scholarly journals Effects of Rapid Preheating and Solution Heat Treatment on Mechanical Properties of AA2618 Forged Samples

2012 ◽  
pp. 177-180
Author(s):  
A. Chennakesava Reddy
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
Solution Heat Treatment ◽  
Mechanical Characteristics ◽  
Rapid Heating ◽  
Radiation Heating ◽  
Rapid Radiation

The microstructural and mechanical characteristics of rapid radiation heating and convection gas-fired heating on AA2618 forged samples have been studied. The rapid heating obtains refinement in grain size. The mechanical properties are greater in the AA2618 samples of rapid radiation heating.

scholarly journals INFLUENCE OF HEAT TREATMENT ON MICROSTRUCTURAL EVOLUTION AND MECHANICAL CHARACTERISTICS OF AA6061 ALUMINUM ALLOY / TERMINIO APDOROJIMO ĮTAKA ALIUMINIO LYDINIO AA6061 MIKROSTRUKTŪRAI IR MECHANINĖMS SAVYBĖMS

2019 ◽  
Vol 11 (0) ◽  
pp. 1-5
Author(s):  
Hanae Chabba ◽  
Irmantas Gedzevičius ◽  
Valentinas Varnauskas ◽  
Driss Dafir ◽  
Fouzi Belmir
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Electrical Resistivity ◽  
Aluminum Alloy ◽  
Solution Heat Treatment ◽  
Room Temperature ◽  
Mechanical Characteristics ◽  
Micro Hardness ◽  
Treatment Conditions ◽  
Experimental Parameters

This study aims to understand the influence of heat treatment on behavior of AA6061 aluminum alloy at room temperature for various heat treatment. Two experimental parameters for this alloy are defined: micro hardness and the electrical resistivity, as a function of heat treatment at ambient temperature. The results show that the heat treatment conditions have an effective influence in mechanical properties of Al-Mg-Si aluminum alloy. This variation of the mechanical properties is the result of microstructural changes which have been observed using optical microscopy. When the material is subjected to a solution heat treatment followed by quenching and artificial aging, its mechanical properties, especially micro hardness and electrical resistivity, reach their highest levels and become very good compared to the other heat treatment applied to the same alloy.

scholarly journals Grain Size Evolution and Mechanical Properties of Nb, V–Nb, and Ti–Nb Boron Type S1100QL Steels

Metals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 492
Author(s):  
Jan Foder ◽  
Jaka Burja ◽  
Grega Klančnik
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
Hot Forging ◽  
Size Control ◽  
High Strength ◽  
Fatigue Properties ◽  
Titanium Addition ◽  
Austenite Grain Size ◽  
Size Evolution

Titanium additions are often used for boron factor and primary austenite grain size control in boron high- and ultra-high-strength alloys. Due to the risk of formation of coarse TiN during solidification the addition of titanium is limited in respect to nitrogen. The risk of coarse nitrides working as non-metallic inclusions formed in the last solidification front can degrade fatigue properties and weldability of the final product. In the presented study three microalloying systems with minor additions were tested, two without any titanium addition, to evaluate grain size evolution and mechanical properties with pre-defined as-cast, hot forging, hot rolling, and off-line heat-treatment strategy to meet demands for S1100QL steel. Microstructure evolution from hot-forged to final martensitic microstructure was observed, continuous cooling transformation diagrams of non-deformed austenite were constructed for off-line heat treatment, and the mechanical properties of Nb and V–Nb were compared to Ti–Nb microalloying system with a limited titanium addition. Using the parameters in the laboratory environment all three micro-alloying systems can provide needed mechanical properties, especially the Ti–Nb system can be successfully replaced with V–Nb having the highest response in tensile properties and still obtaining satisfying toughness of 27 J at –40 °C using Charpy V-notch samples.

scholarly journals Influence of Post Weld Heat Treatment on the Grain Size, and Mechanical Properties of the Alloy-800H Rotary Friction Weld Joints

Materials ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4366
Author(s):  
Saqib Anwar ◽  
Ateekh Ur Rehman ◽  
Yusuf Usmani ◽  
Ali M. Al-Samhan
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
Heat Affected Zone ◽  
Tensile Testing ◽  
Weld Zone ◽  
Alloy 800H ◽  
Weld Joints ◽  
Heat Treated ◽  
Friction Weld

This study evaluated the microstructure, grain size, and mechanical properties of the alloy 800H rotary friction welds in as-welded and post-weld heat-treated conditions. The standards for the alloy 800H not only specify the composition and mechanical properties but also the minimum grain sizes. This is because these alloys are mostly used in creep resisting applications. The dynamic recrystallization of the highly strained and plasticized material during friction welding resulted in the fine grain structure (20 ± 2 µm) in the weld zone. However, a small increase in grain size was observed in the heat-affected zone of the weldment with a slight decrease in hardness compared to the base metal. Post-weld solution heat treatment (PWHT) of the friction weld joints increased the grain size (42 ± 4 µm) in the weld zone. Both as-welded and post-weld solution heat-treated friction weld joints failed in the heat-affected zone during the room temperature tensile testing and showed a lower yield strength and ultimate tensile strength than the base metal. A fracture analysis of the failed tensile samples revealed ductile fracture features. However, in high-temperature tensile testing, post-weld solution heat-treated joints exhibited superior elongation and strength compared to the as-welded joints due to the increase in the grain size of the weld metal. It was demonstrated in this study that the minimum grain size requirement of the alloy 800H friction weld joints could be successfully met by PWHT with improved strength and elongation, especially at high temperatures.

Development of Heat Treatment Mode with Quenching in Different Quenching Environments for the Casing Pipe in Order to Obtain the Required Mechanical Properties

2020 ◽  
Vol 836 ◽  
pp. 41-45
Author(s):  
S.N. Dzhabbarov ◽  
E.I. Pryakhin
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Mechanical Characteristics ◽  
Oil And Gas ◽  
Oil And Gas Industry ◽  
Treatment Mode ◽  
Gas Industry ◽  
Heat Treatment Mode ◽  
Optimal Technology ◽  
Casing Pipe

Development of an optimal technology of heat treatment for blanks of the casing pipe made of steel 40H (GOST 4543) is used in the oil and gas industry for casing. It is accompanied by quenching in various environments to ensure guaranteed obtainment of the required mechanical characteristics. These characteristics are specified in GOST 632-80 and met in order to improve the properties of the 40H steel.

Effect of Post Weld Heat Treatment on Fusion and Heat Affected Zone Microstructure and Mechanical Properties of Inconel X-750 Welds

2011 ◽  
Vol 214 ◽  
pp. 108-112 ◽  
Author(s):  
Prachya Peasura ◽  
Bovornchok Poopat
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
Grain Boundary ◽  
Weld Metal ◽  
Heat Affected Zone ◽  
Aging Temperature ◽  
Post Weld Heat Treatment ◽  
High Aging Temperature ◽  
Zone Microstructure

The Inconel X-750 indicates good hot corrosion resistance, high stability and strength at high temperatures and for this reason the alloy is used in manufacturing of gas turbine hot components. The objective of this research was study the effect of post weld heat treatment (PWHT) on fusion zone and heat affected zone microstructure and mechanical properties of Inconel X-750 weld. After welding, samples were solutionized at 1500 0C. Various aging temperature and times were studied. The results show that aging temperature and time during PWHT can greatly affect microstructure and hardness in fusion zone and heat affected zone. As high aging temperature was used, the grain size also increased and M23C6 at the grain boundary decreased. This can result in decreased of hardness. Moreover excessive aging temperature can result in increasing MC carbide intensity in parent phase (austenite). It can also be observed that M23C6 at the grain boundary decreased due to high aging temperature. This resulted in decreasing of hardness of weld metal and heat affected zone. Experimental results showed that the aging temperature 705 0C aging time of 24 hours provided smaller grain size, suitable size and intensity of MC carbide resulting in higher hardness both in weld metal and HAZ.

Researches on Microstructures and Mechanical Properties of Extruded Mg-Zn-Zr-Y Alloy

2007 ◽  
Vol 353-358 ◽  
pp. 715-717
Author(s):  
Jian Peng ◽  
Rong Shen Liu ◽  
Ding Fei Zhang ◽  
Cheng Meng Song
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
Aging Treatment ◽  
High Strength ◽  
Treatment Processes ◽  
Medium Strength ◽  
Microstructures And Mechanical Properties ◽  
Extruded Products

The microstructures and mechanical properties of Mg-Zn-Zr-Y alloy extruded bar with different heat treatment processes were investigated, including solution treatments of 400 oC, 450 oC and 500 oC for 3 hours followed by 170 oC×24h aging treatment, and solely aging treatments of 160 oC, 180 oC for 24hours without solution after extruding. By comparing the grain size, strength and elongation of the samples, the heat treatment processes for extruded products with high strength and with medium strength were recommended.

Fatigue Behavior of Age-Hardening Cu-6Ni-1.5Si Alloys with Different Grain Sizes

2021 ◽  
Vol 1016 ◽  
pp. 125-131
Author(s):  
Masahiro Goto ◽  
T. Yamamoto ◽  
S.Z. Han ◽  
J. Kitamura ◽  
J.H. Ahn ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Grain Size ◽  
Fatigue Strength ◽  
Solution Heat Treatment ◽  
Fatigue Behavior ◽  
Fatigue Tests ◽  
The Other ◽  
Age Hardening ◽  
Grain Sizes ◽  
Thermomechanical Processes

On the thermomechanical treatments of Cu-Ni-Si alloy, cold-rolling (CR) before solution heat treatment (SHT) is commonly conducted to eliminate defects in a casting slab. In addition, a rolling is applied to reduce/adjust the thickness of casting slab before SHT. In a heavily deformed microstructure by CR, on the other hand, grain growth during a heating in SHT is likely to occur as the result of recrystallization. In general, tensile strength and fatigue strength tend to decrease with an increase in the grain size. However, the effect of difference in grain sizes produced by with and without CR before SHT on the fatigue strength is unclear. In the present study, fatigue tests of Cu-6Ni-Si alloy smooth specimens with a grain fabricated through different thermomechanical processes were conducted. The fatigue behavior of Cu-Ni-Si alloy was discussed.

Development and Characterization of New Ti-25Ta-Zr Alloys for Biomedical Applications

2021 ◽  
Vol 1016 ◽  
pp. 137-144
Author(s):  
Pedro Akira Bazaglia Kuroda ◽  
Fernanda de Freitas Quadros ◽  
Mycaela Vieira Nascimento ◽  
Carlos Roberto Grandini
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Elastic Modulus ◽  
Biomedical Applications ◽  
Solution Heat Treatment ◽  
High Hardness ◽  
Microstructural Characterization ◽  
Β Phase ◽  
Cp Ti ◽  
Microscopy Techniques

This paper deals with the study of the development, structural and microstructural characterization and, selected mechanical properties of Ti-25Ta-50Zr alloy for biomedical applications. The alloy was melted in an arc furnace and various solution heat treatments were performed to analyze the influence of the temperature and time on the structure, microstructure, microhardness and elastic modulus of the samples. The structural and microstructural results, obtained by X-ray diffraction and microscopy techniques, showed that the solution heat treatment performed at high temperatures induces the formation of the β phase, while solution heat treatment performed at low temperatures induces the formation of the α” and ω metastable phases. Regarding the effect of time, samples subjected to heat treatment for 6 hours have only the β phase, indicating that lengthy treatments suppress the α” phase. Regarding the hardness and elastic modulus, the alloy with the α” and ω phases, after treatment performed at a temperature of 500 °C, has a high hardness value and elastic modulus due to the presence of the ω phase that hardens and weakens alloys. The titanium alloys developed in this study have excellent mechanical properties results for use in the orthopedic area, better than many commercial materials such as cp-Ti, stainless steel and Co-Cr alloys.

Sign in / Sign up

Export Citation Format

Share Document