Treatment of Drilling Fluid to Combat Drill Pipe Corrosion

CORROSION ◽  
1990 ◽  
Vol 46 (9) ◽  
pp. 778-782 ◽  
Author(s):  
M. A. Al-Marhoun ◽  
S. S. Rahman
Keyword(s):  
Drilling Fluid ◽  
Drill Pipe

Pipe stick problems of deep well drilling

2021 ◽  
Vol 66 (05) ◽  
pp. 192-195
Author(s):  
Rövşən Azər oğlu İsmayılov ◽  
Keyword(s):  
Drilling Fluid ◽  
Drill Pipe ◽  
Drill String ◽  
Differential Pressure ◽  
Drilling Mud ◽  
Fluid Circulation ◽  
Well Drilling ◽  
Deep Well ◽  
Pressure Pipe ◽  
Bottomhole Pressure

The aricle is about the pipe stick problems of deep well drilling. Pipe stick problem is one of the drilling problems. There are two types of pipe stick problems exist. One of them is differential pressure pipe sticking. Another one of them is mechanical pipe sticking. There are a lot of reasons for pipe stick problems. Indigators of differential pressure sticking are increase in torque and drug forces, inability to reciprocate drill string and uninterrupted drilling fluid circulation. Key words: pipe stick, mecanical pipe stick,difference of pressure, drill pipe, drilling mud, bottomhole pressure, formation pressure

Scaling Formulae for the Wellbore Hydraulics Similitude with Drill Pipe Rotation and Eccentricity

2021 ◽  
Author(s):  
Thad Nosar ◽  
Pooya Khodaparast ◽  
Wei Zhang ◽  
Amin Mehrabian
Keyword(s):  
Power Law ◽  
Flow Rate ◽  
Annular Flow ◽  
Rotation Speed ◽  
Drilling Fluid ◽  
Drill Pipe ◽  
Flow Loop ◽  
Annular Flows ◽  
Fluid Rheology ◽  
Pipe Rotation

Abstract Equivalent circulation density of the fluid circulation system in drilling rigs is determined by the frictional pressure losses in the wellbore annulus. Flow loop experiments are commonly used to simulate the annular wellbore hydraulics in the laboratory. However, proper scaling of the experiment design parameters including the drill pipe rotation and eccentricity has been a weak link in the literature. Our study uses the similarity laws and dimensional analysis to obtain a complete set of scaling formulae that would relate the pressure loss gradients of annular flows at the laboratory and wellbore scales while considering the effects of inner pipe rotation and eccentricity. Dimensional analysis is conducted for commonly encountered types of drilling fluid rheology, namely, Newtonian, power-law, and yield power-law. Appropriate dimensionless groups of the involved variables are developed to characterize fluid flow in an eccentric annulus with a rotating inner pipe. Characteristic shear strain rate at the pipe walls is obtained from the characteristic velocity and length scale of the considered annular flow. The relation between lab-scale and wellbore scale variables are obtained by imposing the geometric, kinematic, and dynamic similarities between the laboratory flow loop and wellbore annular flows. The outcomes of the considered scaling scheme is expressed in terms of closed-form formulae that would determine the flow rate and inner pipe rotation speed of the laboratory experiments in terms of the wellbore flow rate and drill pipe rotation speed, as well as other parameters of the problem, in such a way that the resulting Fanning friction factors of the laboratory and wellbore-scale annular flows become identical. Findings suggest that the appropriate value for lab flow rate and pipe rotation speed are linearly related to those of the field condition for all fluid types. The length ratio, density ratio, consistency index ratio, and power index determine the proportionality constant. Attaining complete similarity between the similitude and wellbore-scale annular flow may require the fluid rheology of the lab experiments to be different from the drilling fluid. The expressions of lab flow rate and rotational speed for the yield power-law fluid are identical to those of the power-law fluid case, provided that the yield stress of the lab fluid is constrained to a proper value.

ERD Drilling Record Achieved in the Gulf of Thailand with an Outstanding Drilling Efficiency

2021 ◽  
Author(s):  
Manchukarn Naknaka ◽  
Trinh Dinh Phu ◽  
Khamawat Siritheerasas ◽  
Pattarapong Prasongtham ◽  
Feras Abu-Jafar ◽  
...  
Keyword(s):  
Chemical Elements ◽  
Drilling Fluid ◽  
Drill Pipe ◽  
Oil Field ◽  
Technology Selection ◽  
Low Flow ◽  
Gulf Of Thailand ◽  
Directional Drilling ◽  
Lost Circulation ◽  
The Gulf Of Thailand

Abstract The objective of this research is to describe the methodology used to drill the most extended reach well (ERD) in the Gulf of Thailand. The Jasmine field is a mature, sophisticated, oil field with many shallow reservoir targets that require a minimum 10,000ft horizontal displacement. As such, the main challenges faced, and the novel technology applied is described in detail by this research. The research is an example of successfully drilling a challenging well, safely and efficiently. The Jasmine C – Well X, is a 3-string design structure with an 11-3/4in top hole, an 8-1/2in intermediate section, and a 6-1/8in reservoir horizontal section. Well X was constructed by utilizing an existing platform well slot. The challenge involved drilling from the top hole to the kickoff point and directional drilling away from the casing stump of the existing well to avoid any collision with nearby wells emanating from the Jasmine C platform. The 8-1/2in hole section was the most important segment as it had to reach the landing point precisely in order to start the 6-1/8in section for GeoSteering in the reservoir section. The 8-1/2in section encountered three challenges that could affect drilling efficiency.Directional Drilling – The complexities of the well profile:The method involved making well inclination (INC) lower than 82deg in the tangent interval in order to reduce the well's tortuosity as much as possible.Hole condition – Hole cleaning and fluid losses control:The method involved the use of Low Toxicity Oil Based Mud (LTOBM) CaCO3 system, the chemical elements in the drilling fluid system could help to seal the high permeable zones.Drilling Engineering – Torque and Drag (T&D) control:The method taked into account the 7in casing run to the bottom of the hole, which the casing driven system did not allow for rotation The well was completed successfully without any additional trips. A Total Depth (TD) was of 13,052ftMD was achieved to reach reservoirs at 3,260ft TVDSS. It was therefore announced in 2019 as a new ERD record for Mubadala Thailand (ERD ratio = 3.26, Directional Difficulty Index (DDI) = 6.95). The top hole and 9-5/8in casing were set in the right depth. An 8-1/2in section was accomplished on the planned trajectory with an average on bottom Rate of Penetration (ROP) at 319 ft/hr. The 6-1/8in section was drilled by geosteering to achieve sub-surface objectives. A total of 2,143ft intervals inside the reservoir was successfully achieved. While drilling, lost circulation events occured, but the mud system was conditioned with Lost Circulation Materials (LCM). Therefore, drilling performance was unaffected. Moreover, the Bit's Total Flow Area (TFA) and Rotary steering systems (RSS) flow restrictor was configured to allow directional drilling at a very low Flow rate of 470gpm. Addition, 30 joints of 5-1/2in Heavy Weight Drill Pipe (HWDP) and 39 joints of 4in HWDP were added into the Bottom Hole Assembly (BHA) to transfer string weight to drill bitsand drill to well TD. As complexities of the well profile were fully aware, the casing was runned and minimized the open hole friction until the casing was deployed successfully. In the Gulf of Thailand, drilling the longest ERD well in a shallow True Vertical Depth (TVD) was clearly groundbreaking and entailed the successful management of the key operational challenges related to identification, job planning, design, technology selection, and implementation. This research illuminates the challenges and technical solutions of long ERD well and serves as an example of what can be achieved in the region and globally.

scholarly journals Simulation of steady-state cuttings transport through a horizontal annulus channel

2019 ◽  
Vol 196 ◽  
pp. 00011 ◽  
Author(s):  
Yaroslav Ignatenko ◽  
Andrey Gavrilov ◽  
Oleg Bocharov ◽  
Roland May
Keyword(s):  
Steady State ◽  
Pressure Gradient ◽  
Yield Stress ◽  
Cross Section ◽  
Drilling Fluid ◽  
Drill Pipe ◽  
Axial Flow ◽  
Cuttings Transport ◽  
Rigid Spheres ◽  
Pipe Rotation

The current study is devoted to simulating cuttings transport by drilling fluid through a horizontal section of borehole with an annular cross section. Drill pipe rotates in fixed eccentric position. Steady-state flow is considered. Cuttings are rigid spheres with equal diameters. The carrying fluid is drilling mud with Herschel-Bulkley rheology. Suspension rheology depends on local shear rate and particles concentration. Continuous mixture model with algebraic equation for particles slipping velocity is used. Two hydrodynamic regimes are considered: axial flow without drill pipe rotation and with drill pipe rotation. In the case of axial flow was shown that increasing of power index n and consistency factor k increases pressure gradient and decreases cuttings concentration. Increasing of yield stress leads to increasing of pressure gradient and cuttings concentration. Cuttings concentration achieves constant value for high yield stress and not depends on it. Rotation of the drill pipe significantly changes the flow structure: pressure loss occurs and particles concentration decreases in the cross section. Two basic regimes of rotational flow are observed: domination of primary vortex around drill pipe and domination secondary vorticity structures. Transition between regimes leads to significant changes of flow integral parameters.

A Multi-Function Agent Used in Drilling Fluid and Completion Fluid MFA-1

2011 ◽  
Vol 335-336 ◽  
pp. 491-497 ◽  
Author(s):  
Ping Quan Wang ◽  
Zong Xue Yu ◽  
Da Yin ◽  
Hong Jun Liang ◽  
Kun Bin Yang
Keyword(s):  
Drilling Fluid ◽  
Drill Pipe ◽  
Economic Benefits ◽  
Functional Treatment ◽  
Social Benefits ◽  
Production Well ◽  
Well Production ◽  
Treatment Agent ◽  
Well Development

In order to take exploratory well, production well ( development well), and reservoir p-retection into account. Multi-functional treatment agent used in drilling fluid and completion flui-d which called MFA-1 has been successfully developed by the equilibrium principle of dispersion and accumulation. The result shows that MFA-1 is fluorescenceless and low (no)toxicity. Also, it has many perfect properties such as filtration reducing, lubrication, anti-collapsing, plugging, re-servoir protection, strong anti-temperature (＞150°C) ,strong anti-salt,ect. Its whole effect is bett-er than sulphonating asphalts HL-Ⅱ and SAS.So MFA-1 is a good succedaneum of sulphonating asphalts.In more than 20 wells of Tarim Oilfield,drilling fluid and completion fluid which prepared with MFA-1 has been successfully used to solve many problems. Such as drill pipe sticking w-hile testing and the underground complex incidents,ect. As a result,it takes good social benefits a-nd good economic benefits.

FORMATION EVALUATION IN HIGHLY-DEVIATED, LONG REACH DEVELOPMENT WELLS ON THE NORTH RANKIN GAS FIELD, NW SHELF, AUSTRALIA

1990 ◽  
Vol 30 (1) ◽  
pp. 310
Author(s):  
D. Lasserre
Keyword(s):  
Drilling Fluid ◽  
Drill Pipe ◽  
Vertical Resolution ◽  
Gas Field ◽  
Log Data ◽  
Formation Evaluation ◽  
North West ◽  
The North ◽  
Reservoir Description ◽  
Resistivity Log

A large proportion of the North West Shelf development gas wells are long reach (greater than 3500 m) and highly deviated. For reservoir description and management purposes, comprehensive formation evaluation needs to be carried out in these wells.Considerable difficulties have been encountered with electric log data acquisition due to friction and borehole conditions in these long, highly-deviated wells. As a result, new techniques to log the zones of interest were introduced. A system using the drill pipe to transport the downhole logging tools has been successfully used.Also, low-toxicity oil-based mud (LTM) was introduced in order to ease drilling problems and borehole conditions. However, owing to the non-conductive nature of the oil-based drilling fluid, improvements were required in the vertical resolution of the resistivity measurements and the estimation of the formation porosity.A computer program using a forward deconvolution technique recently developed by Shell's research laboratory in Holland has been successfully applied to enhance the vertical resolution of the resistivity log reading.The large range of uncertainty on the pore volume has been reduced to reasonable level by calibrating the porosity log data against core data obtained in a well drilled with LTM.

scholarly journals Bitumen Recovery from Crude Bitumen Samples from Halfaya Oilfield by Single and Composite Solvents—Process, Parameters, and Mechanism

Materials ◽  
2019 ◽  
Vol 12 (17) ◽  
pp. 2656 ◽  
Author(s):  
Yunfeng Liu ◽  
Zhengsong Qiu ◽  
Hanyi Zhong ◽  
Zhen Nie ◽  
Jia Li ◽  
...  
Keyword(s):  
Solvent Extraction ◽  
Drilling Fluid ◽  
Drill Pipe ◽  
Economic Losses ◽  
Optimum Process ◽  
Drilling Process ◽  
Solvent Ratio ◽  
Element Analysis ◽  
Asphaltene Content ◽  
Bitumen Recovery

Since 2007, heterogeneous, high-viscosity active bituminous formations have often occurred during the drilling process in Yadavaran oilfield (Iran), Halfaya oilfield (Iraq), and tar sands (Canada). The formation of bitumen exhibits plastic and creep properties, and its adhesion is strong, so drilling accidents are easily caused, such as adhering vibrating screen, drill pipe sticking, lost circulation, and even well abandonment. These complex problems cause huge economic losses. Solvents used to dissolve bitumen are a feasible technology to remove bitumen effectively. In order to solve this problem, we used crude bitumen samples from Halfaya oilfield to study the relation between the bitumen component and different solvents. In this study, the temperature, crude bitumen sample to solvent ratio, stirring rate, stirring time, and ultrasound time on bitumen recovery by toluene were investigated by a single factor experiment. The optimum process parameter for bitumen recovery was obtained. Toluene, n-heptane, tetrahydrofuran, cyclohexane, cyclopentane, ethyl acetate, and n-pentane were chosen as the solvents for single solvent extraction and composite solvent extraction. The bitumen recovery increased significantly with the use of a composite solvent compared to a single solvent. The composite solvent ratio was 1:1. The highest bitumen recovery was 98.9 wt% by toluene/cyclohexane composite solvent. The SARA (saturates, aromatics, resins, and asphaltenes) components of the bitumen were analyzed. The toluene showed the highest asphaltene content, while the n-alkanes showed the lowest asphaltene content. The higher the asphaltene content, the higher the bitumen recovery. The composite solvent obtained the highest asphaltene content and bitumen recovery. The viscosity of bitumen extraction by different solvents was measured. The lower the bitumen viscosity, the higher the bitumen recovery. The element analysis indicated the solvent’s ability to extract bitumen colloids with the C/H ratio. This study provides a reliable theoretical basis for the subsequent adoption of effective anti-bitumen polluted drilling fluid additives.

New Approaches for Drilling Highly Depleted Reservoir in Deep Water Wells

2021 ◽  
Author(s):  
Ola Mohamed Balbaa ◽  
Hesham Mohamed ◽  
Sherif Mohamed Elkholy ◽  
Mohamed ElRashidy ◽  
Robert Munger ◽  
...  
Keyword(s):  
Deep Water ◽  
Drilling Fluid ◽  
Drill Pipe ◽  
Cost Effective ◽  
Drill String ◽  
Drilling Fluids ◽  
Prevention Measures ◽  
Enabling Factors ◽  
Design Changes ◽  
The Mediterranean

Abstract While drilling highly depleted gas reservoirs with a very narrow drilling window, Common drilling methods like utilizing loss of circulation pills, wellbore strengthening materials and managed pressure drilling (MPD) are being used in several reservoirs, yet it cannot be successful or cost effective if applied in a traditional manner. Innovative approaches to enable drilling wells in highly depleted reservoir in the Mediterranean deep water were adopted. The approaches incorporated design changes to the well and Bottom hole assembly (BHA), optimized drilling practices, and unconventional use of MPD while drilling and cementing production liner. Well design change in comparison to offset wells to allow drilling the reservoir in one hole section. Several design changes were considered in the BHA and drilling fluids to prevent as well as mitigate losses and differential sticking risks. From the BHA viewpoint, one of the key successful prevention measures was maximizing the standoff to reduce the contact area with the formation, this was achieved through utilizing spiral heavy wall drill pipe (HWDP) instead of drill collars in addition to a modeled placement of stabilizers and roller reamers. While on the drilling fluid side, Calcium carbonate material was added to strengthen wellbore, prevent losses and avoid formation damage. Particle size up to 1000 micron and concentration up to 40ppb was used to strengthen the depleted sands dynamically while drilling. Furthermore, as mitigation to stuck pipe, Jar and accelerator placement was simulated to achieve optimum impulse and impact force while maintaining the Jar above potential sticking zone. Whereas to address the consequence of a stuck pipe event, disconnect subs were placed in BHA to allow for recovering the drill string efficiently. MPD was first introduced in the Mediterranean in 2007 and continued to develop this well-known technique to mitigate various drilling challenges. For this well, MPD was one of the key enabling factors to safely drill, run and cement the production liner. Surface back pressure MPD allowed using the lowest possible mud weight in the hole and maintaining downhole pressure constant in order to manage the narrow drilling window between the formation pressure and fracture pressure (less than 0.4 ppg). MPD was also applied for the first time for running and cementing the production liner to prevent losses and achieve good cement quality which is a key to successful well production.

Comprehensive experimental investigation of hole cleaning performance in horizontal wells including the effects of drillstring eccentricity, pipe rotation and cuttings size

2021 ◽  
pp. 1-11
Author(s):  
Ahmed K. Abbas ◽  
Mortadha T. Alsaba ◽  
Mohammed F. Al Dushaishi
Keyword(s):  
Flow Rate ◽  
Oil And Gas ◽  
Drilling Fluid ◽  
Drill Pipe ◽  
Real Field ◽  
Operational Parameters ◽  
Cleaning Efficiency ◽  
Hole Cleaning ◽  
Cleaning Performance ◽  
Pipe Rotation

Abstract Extended reach (ERD) wells with a horizontal and highly deviated section are widely applied in the oil and gas industry because they provide higher drainage area than vertical wells; and hence, increase the productivity or injectivity of the well. Among many issues encountered in a complex well trajectory, poor hole cleaning is the most common problem, which occurs mainly in the deviated and horizontal section of oil and gas wells. There are significant parameters that have a serious impact on hole cleaning performance in high-angle and horizontal sections. These include flow rate, rheology and density of the drilling fluid, drillstring eccentricity, pipe rotation, and cuttings size. It has been recognized that the action of most of these parameters to transport drilled cuttings is constantly a point of controversy among oilfield engineers. In the present study, extensive experiments were conducted in an advanced purpose-built flow rig to identify the main parameters affecting on circulate the cuttings out of the test section in a horizontal position. The flow-loop simulator has been designed to allow easy variation of operational parameters in terms of flow rate, mud density, drillstring eccentricity, pipe rotation, and cuttings size. In addition, the study covers the impacts of laminar, transition, and turbulent flow regimes. The goal of such variation in the operational conditions is to simulate real field situations. The results have shown that drill string rotation and flow rate were the operational parameters with the highest positive influence on the cuttings transports process. In contrast, drill pipe eccentricity has a negative influence on cuttings removal efficiency. The cuttings transportation performance is further improved by pipe rotation at different levels of eccentricity, especially at fully eccentric annuli. It was also shown that larger cuttings appeared to be easier to remove in a horizontal annulus than smaller ones. The experimental results would provide a more in-depth understanding of the relationship between drilling operation parameters and hole cleaning efficiency in ERD operations. This will help the drilling teams to realize what action is better to take for efficient cutting transportation.

Experimental research on improving the wear resistance and anti-friction properties of drill pipe joints

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Zhiqiang Huang ◽  
Zhongquan Yin ◽  
Wei Wu
Keyword(s):  
Wear Resistance ◽  
Friction And Wear ◽  
Drilling Fluid ◽  
Drill Pipe ◽  
Flame Spray ◽  
Wear Resistant ◽  
Content Type ◽  
Pipe Joints ◽  
Friction Performance ◽  
Pipe Joint

Purpose The purpose of this study is to solve the oil drill pipe joints and casing excessive wear problems and to improve the drill pipe joint-casing wear resistance and anti-friction properties. Design/methodology/approach On the surface of the drill pipe joints using oxyacetylene flame bead weld (BW) wear-resistant welding wire ARNCO-100XTTM prepares welding layer, high-velocity oxygen fuel (HVOF) Cr3C275-NiCr25 prepares coating and subsonic flame spray and remelt (SFSR) Ni60 prepares coating, then comparing and analyzing the friction and wear of the three types of wear-resistant layers and the casing under the condition of 1.8 g/cm3 mud drilling fluid lubrication. The wear resistance and anti-friction performance of the drill pipe joints were evaluated based on the wear situation, finally revealing its friction and wear mechanisms. Findings Three types of wear-resistant layers can improve the surface wear resistance of drill pipe joints, the wear-resistant layer and the substrate are well combined and the welding layers and coating are both dense and uniform. The wear resistance of the HVOF-Cr3C275-NiCr25 coating is 10.9 times that of the BW-ARNCO-100XTTM weld layer, and the wear resistance of the SFSR-Ni60 weld layer is 2.45 times that of the BW-ARNCO-100XTTM weld layer. The anti-friction properties of SFSR-Ni60 welding layer is the best, followed by HVOF-Cr3C275-NiCr25 coating, and the anti-friction properties of BW-ARNCO-100XTTM welding layer is the worst among the three. Originality/value The research results of this paper have great practical value in the process and material of improving the wear resistance and anti-friction performance of the drill pipe joint casing.

Sign in / Sign up

Export Citation Format

Share Document