Quality of surface finish on furniture doors of MDF board

2019 ◽  
Vol 105 ◽  
pp. 102-106
Author(s):  
GABRIELA SLABEJOVÁ ◽  
MÁRIA ŠMIDRIAKOVÁ ◽  
IVAN VOZAF
Keyword(s):  
Mechanical Properties ◽  
Surface Finish ◽  
Impact Resistance ◽  
Physical And Mechanical Properties ◽  
Coating Material ◽  
Film Hardness ◽  
The Impact

Quality of Surface Finish on Furniture Doors of MDF Board. The paper deals with the assessment of the quality of furniture door surface. The properties were tested on the following types of the surface finish on MDF doors: PVC foil (glossy and matt), acrylic foil, and PUR pigmented coating material. The following physical and mechanical properties of the surfaces were assessed: the film hardness, the impact resistance, and the resistance against scuffing. The polyurethane surface finish and the glossy PVC foil achieved the same film hardness. The impact resistance of the polyurethane finish was significantly lower than the impact resistance of the PVC foils and the acrylic foil. The resistance against scuffing was lower for the polyurethane finish if compared to the foiled surfaces.

scholarly journals Characterisation of Used PP-Based Car Bumpers and Their Recycling Properties

2013 ◽  
Vol 2013 ◽  
pp. 1-12 ◽  
Author(s):  
M. P. Luda ◽  
V. Brunella ◽  
D. Guaratto
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Impact Resistance ◽  
Dynamic Mechanical Properties ◽  
Speed Test ◽  
The Matrix ◽  
Internal Mixer ◽  
Mineral Fillers ◽  
The Impact

Three used PP-based car bumpers are characterized by many techniques (fractionation, IR, TGA, DSC, DMTA, and SEM). They show different impact and static and dynamic mechanical properties depending on their composition and morphology. It appears that block copolymer compatibilizers constituted by polyethylene-polypropylene sequences allow a better compatibility between the rubber domains and the PP matrix leading to relatively high impact resistance. Indeed if the ethylene sequences of the copolymer are large enough to crystallize, the decreased mobility of the whole system impairs the impact resistance. In addition, a higher amount of rubber in domains regular in shape and of greater dimension (1–3 μm) promotes a more homogeneous dispersion of external force inside the material, decreasing the risk of fracture. The amount of mineral fillers regulates the elastic modulus (the higher the load, the higher the modulus); however, a fairly good interfacial adhesion is required for satisfactory impact strength. All PP-based bumpers have been mechanically recycled in an internal mixer to redistribute oxidized species and to reestablish phase compatibilization. Recycling improves mechanical properties in slow speed test but fails to increase impact strength particularly in filled bumper, in which the quality of the matrix/filler interphase is hard to improve by simple remixing.

scholarly journals Influence of unevened grains of metal on the mechanical properties of seamless hot – rolled pipes.

2020 ◽  
pp. 31-33
Author(s):  
I. A. Kovaleva ◽  
N. A. Khodosovskaya ◽  
M. V. Oborov
Keyword(s):  
Mechanical Properties ◽  
High Performance ◽  
Physical And Mechanical Properties ◽  
World Market ◽  
Grain Structure ◽  
Pressure Drops ◽  
Impact Performance ◽  
Hot Rolled ◽  
The Impact

Seamless hot – rolled pipes are a popular metal product on the world market. During operation, pipelines are subjected to cyclic loads associated with temperature fluctuations, vibrations near compressor stations, and pressure drops in the transformed medium. One of the ways to ensure high performance properties is to manage the quality of pipe metal, including that laid in the process of metallurgical production. All the basic physical and mechanical properties of metal materials are structurally sensitive and significantly depend on both the grain size and the degree of uniformity of the grain structure, that is, on the different grain sizes. For metallographic research, samples of pipes with the size of 70,0×12,5 mm of S460NH steel were selected with satisfactory (#1) and unsatisfactory (#2) results of the impact. It was found that the inhomogeneous (multi – grained) microstructure in sample #2 was the reason for obtaining unsatisfactory results of the impact. As a result, it was found that one of the most important characteristics that can guarantee stable and satisfactory results of mechanical characteristics, in particular the impact performance, is a homogeneous grain structure.

The effect of mechanical treatment of beech wood surface on quality of surface finish

2019 ◽  
Vol 106 ◽  
pp. 99-106
Author(s):  
GABRIELA SLABEJOVÁ ◽  
MÁRIA ŠMIDRIAKOVÁ
Keyword(s):  
Film Thickness ◽  
Surface Finish ◽  
Wood Surface ◽  
Mechanical Treatment ◽  
Beech Wood ◽  
Impact Resistance ◽  
Coating Materials ◽  
Surface Finishes ◽  
The Impact

The effect of mechanical treatment of beech wood surface on quality of surface finish. The paper deals with the quality of three surface finishes intended into interior. Three types of coating materials were tested (polyurethane, waterborne, wax). Each type of the surface finish was created on beech wood surface in three various coating thicknesses. The coating thicknesses differed in number of coatings of the coating material. The surface finishes were evaluated according to the impact resistance and the resistance to abrasion. The polyurethane surface finish showed the lowest resistance to abrasion. If the film thickness was increasing, the resistance to abrasion was decreasing. The greatest differences in the resistance to abrasion, depending on the wood surface treatment, were found on the wax surface finish. In general, the waterborne surface finish showed the best resistance to abrasion. Pressing the wood surface before finishing increased the impact resistance of all three surface finishes. The damage of the surfaces was only of grade 2 (No cracks on the surface and the intrusion was only slightly visible). The lowest impact resistance of the surface finishes was found on grinded wood surface; the damage was graded as 4 (Visible large cracks at the intrusion). At the drop height of 400 mm, the effect of the film thickness on the impact resistance was no longer present on all differently mechanically treated surfaces.

scholarly journals Effect of thermocycling in a hard denture liner and acrylic resin after different chemical and mechanical polishing

2015 ◽  
Vol 63 (4) ◽  
pp. 397-404
Author(s):  
Graziella Morfim Schramm ALIGNANI ◽  
Juliana Maria Costa Nuñez PANTOJA ◽  
Jessica Mie Ferreira Koyama TAKAHASHI ◽  
Andréa Araújo de VASCONCELLOS ◽  
Marcelo Ferraz MESQUITA ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Impact Resistance ◽  
Surface Hardness ◽  
Physical And Mechanical Properties ◽  
Acrylic Resin ◽  
Mechanical Polishing ◽  
Tukey Test ◽  
Before And After ◽  
The Impact ◽  
Resistance Tests

Objective: To evaluate the effect of aging in a hard denture reline (New Truliner) and an acrylic resin (Classic) after chemical and mechanical polishing. Methods: Eighty specimens were made, divided randomly between 8 groups: G1.Acrylic Resin Classic (RAC)/Mechanical Polishing (PM); G2.RAC/PM + thermocycling (TR); G3) RAC/Chemical Polishing (PQ); G4.RAC/PQ + TR; G5.New Truliner (NT)/PM; G6.NT/PM + TR; G7. NT/PQ; G8.NT/PQ + TR. The surface hardness was measured before and after polishing, and after TR. The impact resistance tests were measured after all applied treatments. The data were submitted to ANOVA and Tukey test (a=5%). Results: Regardless of the polishing, it was noted that RAC presented significantly higher surface hardness than NT; PM had higher hardness in both materials compared with PQ; on both polishing, the impact resistance of the RAC was higher than NT. Independently of TR test, the impact resistance of the materials that received PQ was higher than received PM. The PQ caused greater changes in properties than the PM. Conclusion: Aging and chemical and mechanical polishing influenced the physical and mechanical properties of hard denture reline and acrylic resin.

Effect of combined drink cans and steel fibers on the impact resistance and mechanical properties of concrete

2020 ◽  
Vol 14 (2) ◽  
pp. 6734-6742
Author(s):  
A. Syamsir ◽  
S. M. Mubin ◽  
N. M. Nor ◽  
V. Anggraini ◽  
S. Nagappan ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Reinforced Concrete ◽  
Impact Resistance ◽  
Fiber Reinforced Concrete ◽  
Steel Fibers ◽  
Fiber Reinforced ◽  
Indirect Tensile ◽  
The Impact

This study investigated the combine effect of 0.2 % drink cans and steel fibers with volume fractions of 0%, 0.5%, 1%, 1.5%, 2%, 2.5% and 3% to the mechanical properties and impact resistance of concrete. Hooked-end steel fiber with 30 mm and 0.75 mm length and diameter, respectively was selected for this study.  The drinks cans fiber were twisted manually in order to increase friction between fiber and concrete. The results of the experiment showed that the combination of steel fibers and drink cans fibers improved the strength performance of concrete, especially the compressive strength, flexural strength and indirect tensile strength. The results of the experiment showed that the combination of steel fibers and drink cans fibers improved the compressive strength, flexural strength and indirect tensile strength by 2.3, 7, and 2 times as compare to batch 1, respectively. Moreover, the impact resistance of fiber reinforced concrete has increase by 7 times as compared to non-fiber concretes. Moreover, the impact resistance of fiber reinforced concrete consistently gave better results as compared to non-fiber concretes. The fiber reinforced concrete turned more ductile as the dosage of fibers was increased and ductility started to decrease slightly after optimum fiber dosage was reached. It was found that concrete with combination of 2% steel and 0.2% drink cans fibers showed the highest compressive, split tensile, flexural as well as impact strength.    

scholarly journals Effect of SWCNT-Tuball Paper on the Lightning Strike Protection of CFRPs and Their Selected Mechanical Properties

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3140
Author(s):  
Kamil Dydek ◽  
Anna Boczkowska ◽  
Rafał Kozera ◽  
Paweł Durałek ◽  
Łukasz Sarniak ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Electrical Conductivity ◽  
Copper Foil ◽  
Impact Resistance ◽  
Mechanical Analysis ◽  
Lightning Strike ◽  
Single Wall Carbon Nanotubes ◽  
Carbon Fibre Reinforced Polymer ◽  
The Impact

The main aim of this work was the investigation of the possibility of replacing the heavy metallic meshes applied onto the composite structure in airplanes for lightning strike protection with a thin film of Tuball single-wall carbon nanotubes in the form of ultra-light, conductive paper. The Tuball paper studied contained 75 wt% or 90 wt% of carbon nanotubes and was applied on the top of carbon fibre reinforced polymer before fabrication of flat panels. First, the electrical conductivity, impact resistance and thermo-mechanical properties of modified laminates were measured and compared with the reference values. Then, flat panels with selected Tuball paper, expanded copper foil and reference panels were fabricated for lightning strike tests. The effectiveness of lightning strike protection was evaluated by using the ultrasonic phased-array technique. It was found that the introduction of Tuball paper on the laminates surface improved both the surface and the volume electrical conductivity by 8800% and 300%, respectively. The impact resistance was tested in two directions, perpendicular and parallel to the carbon fibres, and the values increased by 9.8% and 44%, respectively. The dynamic thermo-mechanical analysis showed higher stiffness and a slight increase in glass transition temperature of the modified laminates. Ultrasonic investigation after lightning strike tests showed that the effectiveness of Tuball paper is comparable to expanded copper foil.

scholarly journals Damage Evolution of Granodiorite after Heating and Cooling Treatments

Minerals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 779
Author(s):  
Mohamed Gomah ◽  
Guichen Li ◽  
Salah Bader ◽  
Mohamed Elkarmoty ◽  
Mohamed Ismael
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Failure Mode ◽  
Physical And Mechanical Properties ◽  
P Wave ◽  
Physical Parameters ◽  
Slow Cooling ◽  
Heating And Cooling ◽  
Natural Rock ◽  
The Impact

The awareness of the impact of high temperatures on rock properties is essential to the design of deep geotechnical applications. The purpose of this research is to assess the influence of heating and cooling treatments on the physical and mechanical properties of Egyptian granodiorite as a degrading factor. The samples were heated to various temperatures (200, 400, 600, and 800 °C) and then cooled at different rates, either slowly cooled in the oven and air or quickly cooled in water. The porosity, water absorption, P-wave velocity, tensile strength, failure mode, and associated microstructural alterations due to thermal effect have been studied. The study revealed that the granodiorite has a slight drop in tensile strength, up to 400 °C, for slow cooling routes and that most of the physical attributes are comparable to natural rock. Despite this, granodiorite thermal deterioration is substantially higher for quick cooling than for slow cooling. Between 400:600 °C is ‘the transitional stage’, where the physical and mechanical characteristics degraded exponentially for all cooling pathways. Independent of the cooling method, the granodiorite showed a ductile failure mode associated with reduced peak tensile strengths. Additionally, the microstructure altered from predominantly intergranular cracking to more trans-granular cracking at 600 °C. The integrity of the granodiorite structure was compromised at 800 °C, the physical parameters deteriorated, and the rock tensile strength was negligible. In this research, the temperatures of 400, 600, and 800 °C were remarked to be typical of three divergent phases of granodiorite mechanical and physical properties evolution. Furthermore, 400 °C could be considered as the threshold limit for Egyptian granodiorite physical and mechanical properties for typical thermal underground applications.

scholarly journals Machining Ti-6Al-4V Alloy Using Nano-Cutting Fluids: Investigation and Analysis

2021 ◽  
Vol 5 (2) ◽  
pp. 42
Author(s):  
Abdelkrem Eltaggaz ◽  
Ibrahim Nouzil ◽  
Ibrahim Deiab
Keyword(s):  
Surface Finish ◽  
Minimum Quantity Lubrication ◽  
Weight Fraction ◽  
Contact Length ◽  
Al2o3 Nanoparticles ◽  
Compressive Stresses ◽  
Cutting Zone ◽  
The Impact ◽  
Cooling And Lubrication

Minimum Quantity Lubrication nanofluid (MQL-nanofluid) is a viable sustainable alternative to conventional flood cooling and provides very good cooling and lubrication in the machining of difficult to cut materials such as titanium and Inconel. The cutting action provides very difficult conditions for the coolant to access the cutting zone and the level of difficulty increases with higher cutting speeds. Furthermore, high compressive stresses, strain hardening and high chemical activity results in the formation of a ‘seizure zone’ at the tool-chip interface. In this work, the impact of MQL-nanofluid at the seizure zone and the corresponding effects on tool wear, surface finish, and power consumption during machining of Ti-6Al-4V was investigated. Aluminum Oxide (Al2O3) nanoparticles were selected to use as nano-additives at different weight fraction concentrations (0, 2, and 4 wt.%). It was observed that under pure MQL strategy there was significant material adhesion on the rake face of the tool while the adhesion was reduced in the presence of MQL-nanofluid at the tool-chip interface, thus indicating a reduction in the tool chip contact length (TCCL) and reduced seizure effect. Furthermore, the flank wear varied from 0.162 to 0.561 mm and the average surface roughness (Ra) varied from 0.512 to 2.81 µm. The results indicate that the nanoparticle concentration and the reduction in the seizure zone positively influence the tool life and quality of surface finish.

Phase Morphology, Thermal and Mechanical Properties of Compatibilized Nylon12/Natural Rubber Blends Using PS/MNR

2013 ◽  
Vol 844 ◽  
pp. 53-56
Author(s):  
Saravalee Saengthaveep ◽  
Sadhan C. Jana ◽  
Rathanawan Magaraphan
Keyword(s):  
Mechanical Properties ◽  
Natural Rubber ◽  
Moisture Absorption ◽  
Rubber Particle ◽  
Impact Resistance ◽  
Phase Morphology ◽  
Thermal And Mechanical Properties ◽  
Binary Blend ◽  
Polyamide 12 ◽  
The Impact

To produce a tough material for application demanding high impact resistance and low moisture absorption, melt blending of Nylon12 (Polyamide 12, PA12) and natural rubber (NR) was carried out in a brabender plasticorder at 210 °C with rotor speed of 70 rpm in the presence of polystyrene/maleated natural rubber (PS/MNR) blend as a compatibilizer. The effect of compatibilizer content (1, 3, 5, 7 and 10 phr) on phase morphology, thermal, and mechanical properties of [Nylon12/NR]/[PS/MNR] blends was investigated by using SEM, DSC, and Izod impact tester, respectively. The result revealed that PS/MNR blend improved the compatibility of Nylon12/NR blends efficiently due to the presence of amide linkage at the interfaces from the reaction between the reactive groups of MNR and the NH2 end groups of Nylon12 during mixing. A fine phase morphology (good dispersion and small dispersed phase size of NR domains in Nylon12 matrix) of [Nylon12/NR]/[PS/MNR] blends was observed at the optimum compatibilizer content of 7 phr, relating to the improvement of mechanical property. The impact energy of [Nylon12/NR]/[PS/MNR] blends was 503 J/m higher than that of neat Nylon12 (115 J/m) and Nylon12/NR binary blend (241 J/m) due to the toughening effect of rubber and proper morphology. The melting temperature of all blends did not change obviously from thermal analysis. However, the presence of rubber particle obstructed the crystallization of Nylon12 phase, leading to the decreasing of %crystallinity from 93% to around 70%.

Sign in / Sign up

Export Citation Format

Share Document