scholarly journals Corrosion Behavior of Spherical Chromium Carbide Reinforced NiCrBSi Hardmetal Coatings in Sulphuric Acid Solution

2022 ◽  
Author(s):  
Li FAN ◽  
Xue-ying LI ◽  
Haiyan CHEN ◽  
Hailiang DU ◽  
Lei SHI
Keyword(s):  
Corrosion Resistance ◽  
Corrosion Behavior ◽  
Chromium Carbide ◽  
Electrochemical Impedance ◽  
Corrosion Current ◽  
Sulphuric Acid Solution ◽  
Passive State ◽  
Negative Effects ◽  
Stable Passive ◽  
Carbide Content

In the present work, four groups of spherical chromium carbide reinforced NiCrBSi hardmetal coatings were prepared on AISI 4145 steel by plasma transferred arc (PTA) technique. The corrosion behavior of the four as-received hardmetal coatings in 0.5 mol/L H2SO4 solution was investigated by polarization curve and electrochemical impedance spectroscopy (EIS). The results revealed that more Cr-rich carbides (Cr3C2, Cr7C3 and M23(C, B)6) are formed in the chromium carbide reinforced coatings, while for the NiCrBSi hardmetal coating only Cr7C3 carbide was detected by XRD. The polarization results show that the chromium carbide reinforced NiCrBSi hardmetal coatings have positive corrosion potential and lower corrosion current, providing a better protective effect to the substrate metal. The combined effects of Cr-rich carbide ceramic phases and a more stable passive film of Cr2O3 greatly improved the corrosion resistances of the chromium carbide reinforced NiCrBSi hardmetal coatings. The coating with the highest spherical chromium carbide addition has more pores because of the thermal stress due to the difference of thermal expansion coefficient between the NiCrBSi bonding phase and chromium carbide reinforced phase. The negative effects of the pores weaken the corrosion resistance, and the coating with the 30% chromium carbide content shows the best corrosion resistance. For NiCrBSi hardmetal coatings with higher reinforced chromium carbide content, the repeatability of the corrosion current obtained by polarization fitting is not as good as that of coatings with lower chromium carbide content. The repeatability of polarization results becomes worse when the specimens keep in a more stable passive state.

Effects of potassium silicate on corrosion behavior of dacromet coating

2019 ◽  
Vol 66 (6) ◽  
pp. 819-826
Author(s):  
Khashayar Tabi ◽  
Mansour Farzam ◽  
Davood Zaarei
Keyword(s):  
Corrosion Resistance ◽  
Corrosion Behavior ◽  
Automobile Industry ◽  
Electrochemical Impedance ◽  
Salt Spray ◽  
Corrosion Current ◽  
Potassium Silicate ◽  
Coated Steel ◽  
Content Type ◽  
New Information

Purpose Potassium silicate sealer was applied on solvent-cleaned, acid-pickled, dacromet-coated steel to improve its corrosion resistance. The purpose of this paper is to study the corrosion behavior of dacromet-coated steel. Design/methodology/approach Potassium silicate sealer was applied on solvent-cleaned, acid-pickled, dacromet-coated steel to improve its corrosion resistance. Electrochemical impedance spectroscopy (EIS), potentiodynamic polarization, scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS) and salt spray were carried out. SEM was used to study the morphological appearance of the surface. Findings The EIS behavior indicated that solvent-cleaned dacromet-coated steel sealed with potassium silicate showed that the corrosion current density was 2.664E − 5 A.cm2 which was reduced to 8.752E − 6 A.cm2 and the corrosion rate, which was 2.264E − 2 mm.year−1, was reduced to 7.438E − 3 mm.year−1 in NaCl 3.5 wt.per cent. EIS was used in NaCl 3.5 wt.%, and the Bode plot characteristics showed that the corrosion protection of solvent-cleaned, dacromet-coated steel was enhanced when sealed with potassium silicate. The EDS results of salt-sprayed, solvent-cleaned samples after 10 days indicated that the main corrosion products are composed of SiO2, ZnO and Al2O3. Research limitations/implications The detection of Li element in EDS was not possible because of the device limitation. Originality/value The current paper provides new information about the sealing properties of potassium silicate and its effects on the corrosion resistance of dacromet coating, which is widely used in many industries such as the automobile industry.

Corrosion Behavior of Zr53.5Cu26.5Ni5Al12Ag3 Bulk Amorphous Alloy in 3.5% NaCl Solution

2011 ◽  
Vol 299-300 ◽  
pp. 427-431
Author(s):  
Yun Li ◽  
Shi Zhi Shang ◽  
Ming Cheng ◽  
Liang Xu ◽  
Shi Hong Zhang
Keyword(s):  
Corrosion Resistance ◽  
Amorphous Alloy ◽  
Passive Film ◽  
Corrosion Behavior ◽  
Electrochemical Impedance ◽  
Corrosion Current ◽  
Bulk Amorphous Alloy ◽  
Nacl Solution ◽  
Current Densities ◽  
Resistance Decrease

The corrosion behavior of Zr53.5Cu26.5Ni5Al12Ag3 bulk amorphous alloy in 3.5% NaCl solution was investigated by using potentiodynamic polarization experiments and electrochemical impedance spectroscopy (EIS). The results show that Zr53.5Cu26.5Ni5Al12Ag3 bulk amorphous alloy has the better corrosion resistance than its corresponding crystal alloy. During the bath in the 3.5% NaCl solution at 25°C, Zr53.5Cu26.5Ni5Al12Ag3 alloy has the lower corrosion current density than the corresponding crystal alloy. After 100h, the corrosion current densities of Zr53.5Cu26.5Ni5Al12Ag3 and the corresponding crystal alloy are 3.8415×10-8A/cm2 and 5.2827×10-7A/cm2, respectively. The results of EIS test indicate that Zr53.5Cu26.5Ni5Al12Ag3 bulk amorphous alloy has the excellent corrosion resistance because passive film with stable structure formed on the surface in 3.5% NaCl solution. With an increase in the immersion time, the passive film becomes thicker. It leads to impedance resistance and corrosion resistance decrease. The surface of Zr53.5Cu26.5Ni5Al12Ag3 bulk amorphous alloy in 3.5% NaCl solution for 100h was analyzed by SEM and EDS. The results show that the corrosive pitting can be found at both the amorphous alloy and the corresponding crystal alloy. However, the amorphous alloy has the better corrosive pitting resistance than the crystal one because the corrosion products formed by selective dissolving of Zr and Al elements. Moreover, the addition of Ag element helps to improve the corrosion resistance of the amorphous alloy greatly.

scholarly journals Corrosion Behavior and Osteogenic Activity of a Biodegradable Orthopedic Implant Mg–Si Alloy with a Gradient Structure

Metals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 781
Author(s):  
Weiyan Jiang ◽  
Wenzhou Yu
Keyword(s):  
Corrosion Resistance ◽  
Corrosion Behavior ◽  
Polarization Resistance ◽  
Corrosion Current Density ◽  
Corrosion Current ◽  
Gradient Structure ◽  
Orthopedic Implant ◽  
Biological Functions ◽  
Alloy Matrix ◽  
Osteogenic Activity

A gradient Mg-8 wt % Si alloy, which was composed of the agglomerated Mg2Si crystals coating (GMS8-1) and the eutectic Mg–Si alloy matrix (GMS8-2), was designed for biodegradable orthopedic implant materials. The bio-corrosion behavior was evaluated by the electrochemical measurements and the immersion tests. The results show that a significant improvement of bio-corrosion resistance was achieved by using the gradient Mg–Si alloy, as compared with the traditional Mg-8 wt % Si alloy (MS8), which should be attributed to the compact and insoluble Mg2Si phase distributed on the surface of the material. Especially, GMS8-1 exhibits the highest polarization resistance of 1610 Ω, the lowest corrosion current density of 1.7 × 10−6 A.cm−2, and the slowest corrosion rate of 0.10 mm/year. In addition, GMS8-1 and GMS8-2 show better osteogenic activity than MS8, with no cytotoxicity to MC3T3-E1 cells. This work provides a new way to design a gradient biodegradable Mg alloys with some certain biological functions.

scholarly journals Chemical Composition and Corrosion Behavior of a-C:H/DLC Film-Coated Titanium Substrate in Simulated PEMFC Environment

Coatings ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 820
Author(s):  
Beibei Han ◽  
Mengyuan Yan ◽  
Dongying Ju ◽  
Maorong Chai ◽  
Susumu Sato
Keyword(s):  
Corrosion Resistance ◽  
Corrosion Behavior ◽  
Metal Ion ◽  
Ion Beam ◽  
Titanium Substrate ◽  
Corrosion Current ◽  
Ion Concentration ◽  
Bipolar Plates ◽  
High Adhesion ◽  
Corrosion Behaviors

The amorphous hydrogenated (a-C:H) film-coated titanium, using different CH4/H2 and deposition times, was prepared by the ion beam deposition (IBD) method, which has the advantage of high adhesion because of the graded interface mixes at the atomic level. The chemical characterizations and corrosion behaviors of a-C:H film were investigated and evaluated by SEM, AFM, Raman spectroscopy, EPMA, TEM and XPS. An a-C:H film-coated titanium was corroded at 0.8 V, 90 °C in a 0.5 mol/L H2SO4 solution for 168 h. The metal ion concentration in the H2SO4 corrosion solution and the potentiodynamic polarization behavior were evaluated. Results indicate that a higher CH4/H2 of 1:0 and a deposition time of 12 h can result in a minimum ID/IG ratio of 0.827, Ra of 5.76 nm, metal ion concentration of 0.34 ppm in the corrosion solution and a corrosion current of 0.23 µA/cm2. The current density in this work meets the DOE’s 2020 target of 1 µA/cm2. Electrical conductivity is inversely proportional to the corrosion resistance. The significant improvement in the corrosion resistance of the a-C:H film was mainly attributed to the increased sp3 element and nanocrystalline TiC phase in the penetration layer. As a result, the a-C:H film-coated titanium at CH4/H2 = 1:0 with improved anti-corrosion behavior creates a great potential for PEMFC bipolar plates.

scholarly journals Assessment of nickel titanium and beta titanium corrosion resistance behavior in fluoride and chloride environments

2013 ◽  
Vol 83 (5) ◽  
pp. 864-869 ◽  
Author(s):  
Elisa J. Kassab ◽  
José Ponciano Gomes
Keyword(s):  
Corrosion Resistance ◽  
Corrosion Behavior ◽  
Electrochemical Impedance ◽  
Fluoride Concentration ◽  
Nickel Titanium ◽  
Localized Corrosion ◽  
General Corrosion ◽  
Nacl Solution ◽  
Galvanic Coupling ◽  
Beta Titanium

ABSTRACT Objective: To assess the influence of fluoride concentration on the corrosion behavior of nickel titanium (NiTi) superelastic wire and to compare the corrosion resistance of NiTi with that of beta titanium alloy in physiological solution with and without addition of fluoride. Materials and Methods: NiTi corrosion resistance was investigated through electrochemical impedance spectroscopy and anodic polarization in sodium chloride (NaCl 0.15 M) with and without addition of 0.02 M sodium fluoride (NaF), and the results were compared with those associated with beta titanium. The influence of fluoride concentration on NiTi corrosion behavior was assessed in NaCl (0.15 M) with and without 0.02, 0.04, 0.05, 0.07, and 0.12 M NaF solution. Galvanic corrosion between NiTi and beta titanium were investigated. All samples were characterized by scanning electron microscopy. Results: Polarization resistance decreased when NaF concentration was increased, and, depending on NaF concentration, NiTi can suffer localized or generalized corrosion. In NaCl solution with 0.02 M NaF, NiTi suffer localized corrosion, while beta titanium alloys remained passive. Current values near zero were observed by galvanic coupling of NiTi and beta titanium. Conclusions: There is a decrease in NiTi corrosion resistance in the presence of fluoride. The corrosion behavior of NiTi alloy depends on fluoride concentration. When 0.02 and 0.04 M of NaF were added to the NaCl solution, NiTi presented localized corrosion. When NaF concentration increased to 0.05, 0.07, and 0.12 M, the alloy presented general corrosion. NiTi corrosion resistance behavior is lower than that of beta titanium. Galvanic coupling of these alloys does not increase corrosion rates.

Evaluation of the corrosion behavior of AZ31 magnesium alloy with different protein concentrations

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Yucong Ma ◽  
Mohd Talha ◽  
Qi Wang ◽  
Zhonghui Li ◽  
Yuanhua Lin
Keyword(s):  
Corrosion Resistance ◽  
Corrosion Behavior ◽  
Electrochemical Impedance ◽  
Surface Film ◽  
Energy Dispersive Spectrometer ◽  
Inhibitory Effect ◽  
Corrosion Process ◽  
High Concentration ◽  
Content Type ◽  
Atomic Force

Purpose The purpose of this paper is to study systematically the corrosion behavior of AZ31 magnesium (Mg) alloy with different concentrations of bovine serum albumin (BSA) (0, 0.5, 1.0, 1.5, 2.0 and 5.0 g/L). Design/methodology/approach Electrochemical impedance spectroscopy and potential dynamic polarization tests were performed to obtain corrosion parameters. Scanning electrochemical microscopy (SECM) was used to analyze the local electrochemical activity of the surface film. Atomic force microscope (AFM), Scanning electron microscope-Energy dispersive spectrometer and Fourier transform infrared spectroscopy were used to determine the surface morphology and chemical composition of the surface film. Findings Experimental results showed the presence of BSA in a certain concentration range (0 to 2.0 g/L) has a greater inhibitory effect on the corrosion of AZ31, however, the presence of high-concentration BSA (5.0 g/L) would sharply reduce the corrosion resistance. Originality/value When the concentration of BSA is less than 2.0 g/L, the corrosion resistance of AZ31 enhances with the concentration. The adsorption BSA layer will come into being a physical barrier to inhibit the corrosion process. However, high-concentration BSA (5.0 g/L) will chelate with dissolved metal ions (such as Mg and Ni) to form soluble complexes, which increases the roughness of the surface and accelerates the corrosion process.

scholarly journals Corrosion of Mechanically Alloyed Nanostructured FeAl Intermetallic Powders

2012 ◽  
Vol 2012 ◽  
pp. 1-9 ◽  
Author(s):  
A. Torres-Islas ◽  
C. Carachure ◽  
S. Serna ◽  
B. Campillo ◽  
G. Rosas
Keyword(s):  
Corrosion Behavior ◽  
Electrochemical Impedance ◽  
Electrochemical Techniques ◽  
Corrosion Current ◽  
Test Time ◽  
Uniform Corrosion ◽  
Mechanically Alloyed ◽  
Solution Ph ◽  
Surface Corrosion ◽  
Electrochemical Testing

The corrosion behavior of the Fe40Al60nanostructured intermetallic composition was studied using electrochemical impedance spectroscopy (EIS) and linear polarization resistance (LPR) techniques with an innovative electrochemical cell arrangement. The Fe40Al60(% at) intermetallic composition was obtained by mechanical alloying using elemental powders of Fe (99.99%) and Al (99.99%). All electrochemical testing was carried out in Fe40Al60particles that were in water with different pH values. Temperature and test time were also varied. The experimental data was analyzed as an indicator of the monitoring of the particle corrosion current densityicorr. Different oxide types that were formed at surface particle were found. These oxides promote two types of surface corrosion mechanisms: (i) diffusion and (ii) charge transfer mechanisms, which are a function oficorrbehavior of the solution, pH, temperature, and test time. The intermetallic was characterized before and after each test by transmission electron microscopy. Furthermore, the results show that at the surface particles uniform corrosion takes place. These results confirm that it is possible to sense the nanoparticle corrosion behavior by EIS and LPR conventional electrochemical techniques.

Effect of Uniaxial Tension-Induced Plastic Strain on the Microstructure and Corrosion Behavior of 13Cr Martensitic Stainless Steel

CORROSION ◽  
10.5006/3516 ◽  
2020 ◽  
Vol 76 (12) ◽  
Author(s):  
Salar Salahi ◽  
Mostafa Kazemipour ◽  
Ali Nasiri
Keyword(s):  
Stainless Steel ◽  
Plastic Strain ◽  
Corrosion Behavior ◽  
Chromium Carbide ◽  
Martensitic Stainless Steel ◽  
Electrochemical Impedance ◽  
Passive Layer ◽  
High Concentration ◽  
Pitting Potential ◽  
Heat Treated Sample

This study aims to understand the correlation between the manufacturing process-induced plastic deformation, microstructure, and corrosion behavior of a 13Cr martensitic stainless steel tubing material (UNS S42000). Comparisons were made between the microstructure, crystallographic orientation, and corrosion performance of a texture-free, heat-treated sample and uniaxially tensioned samples to the elongations of 5% and 22%. Cyclic potentiodynamic polarization tests and electrochemical impedance spectroscopy were performed on all samples in aerated 3.5 wt% NaCl electrolyte at room temperature. Overall, the corrosion resistance of the samples was found to decrease with increasing deformation level. A more stable and higher corrosion potential and pitting potential values with a better stability of the passive film were derived for the nondeformed sample, whereas the 5% and 22% elongated samples exhibited lower corrosion and pitting potential values and were characterized by having a less stable passive layer. All samples consistently revealed micropit formation on the lath boundaries where a high concentration of chromium carbide precipitates was detected. Increasing the level of plastic strain in 13Cr stainless steel was found to enlarge the size of sensitized regions along the matrix/coarse chromium carbide precipitates interface, leading to more regions susceptible to initiation and propagation of pitting.

scholarly journals Erosion-Corrosion Protection Due to Cr3C2-NiCr Cermet Coating on Stainless Steel

Coatings ◽  
2020 ◽  
Vol 10 (11) ◽  
pp. 1042
Author(s):  
Panneer Selvam Kevin ◽  
Abhishek Tiwari ◽  
Saravanan Seman ◽  
Syed Ali Beer Mohamed ◽  
Rengaswamy Jayaganthan
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
Corrosion Behavior ◽  
Potentiodynamic Polarization ◽  
Electrochemical Impedance ◽  
Turbine Blades ◽  
Continuous Exposure ◽  
Hydro Power ◽  
Cermet Coating ◽  
Erosion Corrosion

Cr3C2–NiCr coatings have been used extensively to combat the erosion corrosion of hydro power turbine blades made of stainless steel. Cr3C2–NiCr coatings are also used in aqueous corrosive environments due to the high corrosion resistance rendered by the NiCr binder. In this investigation, both erosion and corrosion environments are introduced to cermet coating to study corrosion behavior using potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) techniques. The cermet coatings are useful for reducing the risk of deterioration of mechanical properties of hydro power turbines due to the continuous exposure to the erosive and corrosive action of the corrosive environment containing silt. It was observed that Cr3C2–NiCr coating offered a reasonable improvement in corrosion resistance when compared to bare substrate. The corrosion behavior of the coating was studied in a 150 mL solution of 0.1 M NaCl with 2 gms of quartz particles (0.2–0.8 mm) at various rotation speeds (3000, 4500, 6000 rpm) of the solution over a 1 h immersion using potentiodynamic polarization and EIS studies in a specifically designed experimental set-up for erosion corrosion. When compared to the bare stainless steel samples at 3000 rpm and 6000 rpm, the coating showed the highest improvement at 6.57 times and the least improvement at 3.79 times, respectively.

Effect of Shot Peening on Microstructure and Properties of 34CrMo4 Alloy

2018 ◽  
Vol 934 ◽  
pp. 105-110 ◽  
Author(s):  
Ke Jian Li ◽  
Qiang Zheng ◽  
Yue Lin Qin ◽  
Xiao Wei Liu
Keyword(s):  
Plastic Deformation ◽  
Corrosion Resistance ◽  
Shot Peening ◽  
Electrochemical Impedance ◽  
Corrosion Current ◽  
Optical Microscope ◽  
Microstructure And Properties ◽  
Before And After ◽  
Sever Plastic Deformation ◽  
Evolution Of Microstructure

Plastic deformation can induce surface modification, such as shot peening (SP) on workpiece surface is the hot issue of recent scientific research. SP is the efficient way to improve mechanical behavior of specimens by inducing sever plastic deformation on their surface. Nevertheless, this surface treatment induced complex microstructural evolutions such as grain refinement, will enhance the corrosion resistance of specimens. In this work, the microstructure and properties of 34CrMo4 alloy of before and after SP for 20 min have been investigated. The evolution of microstructure and properties were analyzed from the surface and cross-section. The microstructure morphology at the different depth was determined by optical microscope. The results show grain size is increasing with the depth, and the microhardness and compressive residual stress decrease gradually. In terms of corrosion resistance, the 50 μm depth specimen has the best property than other depth, which the potential and corrosion current density are-0.484 V and-5.72 Acm-2, respectively. The maximum polarization resistance is 2055 Ωcm2by capacitive arc radius of electrochemical impedance spectroscopy.

Sign in / Sign up

Export Citation Format

Share Document