scholarly journals INVESTIGATION OF THE METHOD OF PROCESSING HOLES WITH A ROTARY CUP CUTTER WITH SURFACING

2021 ◽  
pp. 1-6
Author(s):  
Bakytzhan Donenbayev ◽  
Karibek Sherov ◽  
Assylkhan Mazdubay ◽  
Aybek Sherov ◽  
Medgat Mussayev ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Cutting Tool ◽  
Large Diameter ◽  
Cutting Tools ◽  
Experimental Studies ◽  
Surface Hardness ◽  
Hard Metal ◽  
Metal Plates ◽  
Study Results ◽  
The Cost

This article presents the experimental study results of the process of rotational friction holes boring using a cup cutter surfaced by STOODY M7-G material. As a result of experimental studies, the following quality indicators were achieved: surface roughness within Ra=10÷1,25 micrometer; surface hardness within HB 212-248. Using a cup cutter surfaced by STOODY M7-G material in case of rotational friction boring of large-diameter holes for large-sized parts can improve processing performance in comparison with cutting tools equipped with hard metal plates and provided the required surface roughness. Preliminary calculations showed that the manufacture of cup cutters from non-instrumental materials reduces the cost of the cutting tool by 5-7 times and the cost of the operation by 1.5-2 times.

scholarly journals Method of drilling process control and experimental studies of resistance forces during bits drilling with PDC cutters

2020 ◽  
Vol 245 ◽  
pp. 539-546
Author(s):  
Vyacheslav Neskromnykh ◽  
Marina Popova ◽  
A. Golovchenko ◽  
P. PETENEV ◽  
Liu Baochang
Keyword(s):  
Cutting Tool ◽  
Cutting Tools ◽  
Experimental Studies ◽  
Rotation Frequency ◽  
Rock Cutting ◽  
Rock Failure ◽  
Drilling Process ◽  
Drilling Mud ◽  
Cost Of Time ◽  
The Cost

A rational, theoretically proved and empirically verified control system is a condition for optimal management of the drilling process in compliance with the criteria for minimizing the cost of time and material resources. A new generation of rock-cutting tools using PDC cutters (polycrystalline diamante cutters), which are extremely effective when drilling wells for various purposes in medium-hard rocks, dictates the need to develop methods and criteria for optimal control of the drilling process using this tool. The paper presents an analysis of the force interaction between rock-cutting elements, face rock, and drilling mud saturated with slam, highlights the influencing factors and provides dependencies for determining the parameters of rock failure. Empirical verification of the theoretical propositions was carried out based on the data analysis from experimental bit drilling of marble with PDC cutters with a diameter of 76.2 mm, processed using the method of full factor experiment to obtain mathematical models of factors and their graphical interpretation. The method of controlling the drilling process based on the optimal ratio of the tool rotation frequency, axial weight and deepening per one turnover is considered, which allows determining the rock failure mode at the well bottom by indirect signs and choose the optimal values of the drilling mode parameters that correspond to the most optimal conditions in terms of achieving the maximum mechanical drilling speed in conjunction with the rational mode of rock-cutting tool operation. A scheme is presented that contains possible variants of the bit run mode and ways to recognize them by the ratio of the deepening per turnover and the rotation frequency of the rock-cutting tool.

scholarly journals Evaluation of Cutting-Tool Coating on the Surface Roughness and Hole Dimensional Tolerances during Drilling of Al6061-T651 Alloy

Materials ◽  
2021 ◽  
Vol 14 (7) ◽  
pp. 1783
Author(s):  
Hamza A. Al-Tameemi ◽  
Thamir Al-Dulaimi ◽  
Michael Oluwatobiloba Awe ◽  
Shubham Sharma ◽  
Danil Yurievich Pimenov ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Cutting Tool ◽  
Good Practice ◽  
Cutting Tools ◽  
Statistical Design ◽  
Cutting Parameters ◽  
Statistical Design Of Experiments ◽  
Hole Quality ◽  
Coated Tools ◽  
Tool Coating

Aluminum alloys are soft and have low melting temperatures; therefore, machining them often results in cut material fusing to the cutting tool due to heat and friction, and thus lowering the hole quality. A good practice is to use coated cutting tools to overcome such issues and maintain good hole quality. Therefore, the current study investigates the effect of cutting parameters (spindle speed and feed rate) and three types of cutting-tool coating (TiN/TiAlN, TiAlN, and TiN) on the surface finish, form, and dimensional tolerances of holes drilled in Al6061-T651 alloy. The study employed statistical design of experiments and ANOVA (analysis of variance) to evaluate the contribution of each of the input parameters on the measured hole-quality outputs (surface-roughness metrics Ra and Rz, hole size, circularity, perpendicularity, and cylindricity). The highest surface roughness occurred when using TiN-coated tools. All holes in this study were oversized regardless of the tool coating or cutting parameters used. TiN tools, which have a lower coating hardness, gave lower hole circularity at the entry and higher cylindricity, while TiN/TiAlN and TiAlN seemed to be more effective in reducing hole particularity when drilling at higher spindle speeds. Finally, optical microscopes revealed that a built-up edge and adhesions were most likely to form on TiN-coated tools due to TiN’s chemical affinity and low oxidation temperature compared to the TiN/TiAlN and TiAlN coatings.

scholarly journals Remaining Useful Life Prediction of Cutting Tools Using an Inverse Gaussian Process Model

2021 ◽  
Vol 11 (11) ◽  
pp. 5011
Author(s):  
Yuanxing Huang ◽  
Zhiyuan Lu ◽  
Wei Dai ◽  
Weifang Zhang ◽  
Bin Wang
Keyword(s):  
Surface Roughness ◽  
Failure Criterion ◽  
Cutting Tool ◽  
Cutting Tools ◽  
Remaining Useful Life ◽  
Model Parameters ◽  
Inverse Gaussian ◽  
Wear Process ◽  
Useful Life ◽  
Dynamic Wear

In manufacturing, cutting tools gradually wear out during the cutting process and decrease in cutting precision. A cutting tool has to be replaced if its degradation exceeds a certain threshold, which is determined by the required cutting precision. To effectively schedule production and maintenance actions, it is vital to model the wear process of cutting tools and predict their remaining useful life (RUL). However, it is difficult to determine the RUL of cutting tools with cutting precision as a failure criterion, as cutting precision is not directly measurable. This paper proposed a RUL prediction method for a cutting tool, developed based on a degradation model, with the roughness of the cutting surface as a failure criterion. The surface roughness was linked to the wearing process of a cutting tool through a random threshold, and accounts for the impact of the dynamic working environment and variable materials of working pieces. The wear process is modeled using a random-effects inverse Gaussian (IG) process. The degradation rate is assumed to be unit-specific, considering the dynamic wear mechanism and a heterogeneous population. To adaptively update the model parameters for online RUL prediction, an expectation–maximization (EM) algorithm has been developed. The proposed method is illustrated using an example study. The experiments were performed on specimens of 7109 aluminum alloy by milling in the normalized state. The results reveal that the proposed method effectively evaluates the RUL of cutting tools according to the specified surface roughness, therefore improving cutting quality and efficiency.

scholarly journals Milling Inconel 718 Workpiece With Cryogenically Treated And Untreated Cutting Tools

2021 ◽  
Author(s):  
Hüseyin Gürbüz ◽  
Şehmus Baday
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Abrasive Wear ◽  
Inconel 718 ◽  
Cutting Tool ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Cutting Tool Wear ◽  
Feed Force

Abstract Although Inconel 718 is an important material for modern aircraft and aerospace, it is a kind material, which is known to have low machinability. Especially, while these types of materials are machined, high cutting temperatures, BUE on cutting tool, high cutting forces and work hardening occur. Therefore, in recent years, instead of producing new cutting tools that can withstand these difficult conditions, cryogenic process, which is a heat treatment method to increase the wear resistance and hardness of the cutting tool, has been applied. In this experimental study, feed force, surface roughness, vibration, cutting tool wear, hardness and abrasive wear values that occurred as a result of milling of Inconel 718 material by means of cryogenically treated and untreated cutting tools were investigated. Three different cutting speeds (35-45-55 m/min) and three different feed rates (0.02-0.03-0.04 mm/tooth) at constant depth of cut (0.2 mm) were used as cutting parameters in the experiments. As a result of the experiments, lower feed forces, surface roughness, vibration and cutting tool wear were obtained with cryogenically treated cutting tools. As the feed rate and cutting speed were increased, it was seen that surface roughness, vibration and feed force values increased. At the end of the experiments, it was established that there was a significant relation between vibration and surface roughness. However, there appeared an inverse proportion between abrasive wear and hardness values. While BUE did not occur during cryogenically treated cutting tools, it was observed that BUE occurred in cutting tools which were not cryogenically treated.

Life Prediction of Cutting Tool by the Workpiece Cutting Condition

2011 ◽  
Vol 223 ◽  
pp. 554-563 ◽  
Author(s):  
Noemia Gomes de Mattos de Mesquita ◽  
José Eduardo Ferreira de Oliveira ◽  
Arimatea Quaresma Ferraz
Keyword(s):  
Cutting Tool ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Operating Conditions ◽  
Production Costs ◽  
Depth Of Cut ◽  
Cutting Condition ◽  
Workpiece Material ◽  
The Cost

Stops to exchange cutting tool, to set up again the tool in a turning operation with CNC or to measure the workpiece dimensions have direct influence on production. The premature removal of the cutting tool results in high cost of machining, since the parcel relating to the cost of the cutting tool increases. On the other hand the late exchange of cutting tool also increases the cost of production because getting parts out of the preset tolerances may require rework for its use, when it does not cause bigger problems such as breaking of cutting tools or the loss of the part. Therefore, the right time to exchange the tool should be well defined when wanted to minimize production costs. When the flank wear is the limiting tool life, the time predetermination that a cutting tool must be used for the machining occurs within the limits of tolerance can be done without difficulty. This paper aims to show how the life of the cutting tool can be calculated taking into account the cutting parameters (cutting speed, feed and depth of cut), workpiece material, power of the machine, the dimensional tolerance of the part, the finishing surface, the geometry of the cutting tool and operating conditions of the machine tool, once known the parameters of Taylor algebraic structure. These parameters were raised for the ABNT 1038 steel machined with cutting tools of hard metal.

Optimization of Surface Roughness by Using Different Cutting Tools for Aluminum Alloy 6063

2020 ◽  
Vol 17 (2) ◽  
pp. 961-966
Author(s):  
Allina Abdullah ◽  
Afiqah Azman ◽  
B. M. Khirulrizwan
Keyword(s):  
Surface Roughness ◽  
Aluminum Alloy ◽  
Optimum Condition ◽  
Feed Rate ◽  
Optimum Parameter ◽  
Cutting Tool ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Numerical Control ◽  
Depth Of Cut

This research outlines an experimental study to determine the optimum parameter of cutting tool for the best surface roughness (Ra) of Aluminum Alloy (AA) 6063. For the experiment in this research, cutting parameters such as cutting speed, depth of cut and feed rate are used to identify the effect of both cutting tools which are tungsten carbide and cermet towards the surface roughness (Ra) of material AA6063. The machining operation involved to cut the material is turning process by using Computer Numerical Control (CNC) Lathe machine. The experimental design was designed by Full Factorial. The experiment that had been conducted by the researcher is 33 with 2 replications. The total number of the experiments that had been run is 54 runs for each cutting tool. Thus, the total number of experiments for both cutting tools is 108 runs. ANOVA analysis had been analyzed to identify the significant factor that affect the Ra result. The significant factors that affect the Ra result of AA6063 are feed rate and cutting speed. The researcher used main effect plot to determine the factor that most influenced the surface roughness of AA6063, the optimum condition of surface roughness and the optimum parameter of cutting tool. The factor that most influenced the surface roughness of AA6063 is feed rate. The optimum condition of surface roughness is at the feed rate of 0.05 mm/rev, cutting speed of 600 rpm and depth of cut of 0.10 mm. While the optimum parameter of cutting tool is cermet insert with the lowest value of surface roughness (Ra) result which is 0.650 μm.

The Predictive Model of Surface Roughness and Searching System in Database for Cutting Tool Grinding

2009 ◽  
Vol 626-627 ◽  
pp. 11-16 ◽  
Author(s):  
Yung Cheng Wang ◽  
Chen Hsiang Chen ◽  
Bean Yin Lee
Keyword(s):  
Surface Roughness ◽  
Cutting Tool ◽  
Rapid Development ◽  
Cutting Tools ◽  
Experiment Planning ◽  
Grinding Wheel ◽  
End Mill ◽  
Grinding Parameters ◽  
End Mills ◽  
Tool Grinding

Due to the rapid development in recent cutting technology, demands for different types of precise cutting tools become increasingly complicated. Since the design and grinding of end-mills are the last and the most important processing for cutting tools. The geometrical accuracy and the cutting performance of an end-mill depend essentially on the grinding. However, the complicated geometry of an end-mill will be ground by the specific software of CAD/CAM on the 5-axis CNC tool grinding machine. The precision of end-mill grinder will be determined by the performance of 5-axis CNC tool grinder and setting of grinding parameters. Three regulation factors for grinding are grit size of the diamond grinding wheel, grinding speed and the feeding speed. The variable ranges of each parameter can be divided in large, medium and small interval. In this study for an end-mill with fixed geometrical profile, a series of different grinding parameters have been utilized by the 33 factorial experiment planning. And tool grinding experiments for the rod material specification of tungsten carbide have been performed by 5-axis CNC tool grinder. After grinding, surface roughness of tools will be measured. The reliability and precision of the end-mill grinding can be enhanced by the prediction model of polynomial network for surface roughness of end-mills. Besides, the database system for cutting tool has benn established. Totally 4802 data were constructed in the relational database according to the characteristics of tools.

scholarly journals Experimental Investigation on the Advantages of Dry Machining over Wet Machining during Turning of AISI 1020 Steel

2021 ◽  
Vol 8 ◽  
pp. 12-25
Author(s):  
Boki Dugo Bedada ◽  
Guteta Kabeta Woyesssa ◽  
Moera Gutu Jiru ◽  
Besufekad Negash Fetene ◽  
Tekle Gemechu
Keyword(s):  
Surface Roughness ◽  
Tool Life ◽  
Cutting Tools ◽  
Cutting Temperature ◽  
Dry Machining ◽  
Dry Turning ◽  
Total Cost ◽  
Cemented Carbide Tool ◽  
Lathe Machine ◽  
The Cost

In this study, the experiment was conducted to investigate the advantage of dry machining over wet machining during turning of AISI 1020 steel using cemented carbide tool on a CNC lathe machine. Surface roughness and cutting temperature were measured by VOGEL surface roughness tester and infrared thermometer respectively. The experiments were conducted based on Taguchi L9 orthogonal array design. Surface roughness, cutting temperature, tool life, and machining cost were analyzed graphically. The average surface roughness and cutting temperature achieved with wet machining was 2.01 μm and 26.540C, which was 17.41% and 44.86% respectively, lower than dry machining. The high cutting temperature in dry turning result in short tool life, which was 41.15% shorter than wet turning. The machining cost of wet turning was about 56% greater than the cost of dry turning. The cost of coolant in wet turning is 42.88% greater than that of the cutting tools. The highest cost was shared by tool cost, which was 81.33% of the total cost for dry turning, while 70.00% of the total cost was shared by coolant cost for wet turning. Results revealed that dry turning is more economical than wet turning.

scholarly journals Optimisation of Cutting Tool and Cutting Parameters in Face Milling of Custom 450 through the Taguchi Method

2019 ◽  
Vol 2019 ◽  
pp. 1-10 ◽  
Author(s):  
Harun Gokce
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Tool Wear ◽  
Taguchi Method ◽  
Cutting Tool ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Cutting Tool Wear ◽  
Wide Range

Stainless steels with unique corrosion resistance are used in applications with a wide range of fields, especially in the medical, food, and chemical sectors, to maritime and nuclear power plants. The low heat conduction coefficient and the high mechanical properties make the workability of stainless steel materials difficult and cause these materials to be in the class of hard-to-process materials. In this study, suitable cutting tools and cutting parameters were determined by the Taguchi method taking surface roughness and cutting tool wear into milling of Custom 450 martensitic stainless steel. Four different carbide cutting tools, with 40, 80, 120, and 160 m/min cutting speeds and 0.05, 0.1, 0.15, and 0.2 mm/rev feed rates, were selected as cutting parameters for the experiments. Surface roughness values and cutting tool wear amount were determined as a result of the empirical studies. ANOVA was performed to determine the significance levels of the cutting parameters on the measured values. According to ANOVA, while the most effective cutting parameter on surface roughness was the feed rate (% 50.38), the cutting speed (% 81.15) for tool wear was calculated.

Modification of the Surface of a Reconditioned Cutting Tool via Laser Ablation

2021 ◽  
Vol 1037 ◽  
pp. 558-563
Author(s):  
Elmar Yagyaev ◽  
Seran Akimov
Keyword(s):  
Laser Ablation ◽  
Tool Life ◽  
Processing Speed ◽  
Cutting Tool ◽  
Cutting Tools ◽  
Experimental Studies ◽  
Untreated Sample ◽  
Nanosecond Duration ◽  
Modified Surfaces ◽  
Modification Of The Surface

The article discusses the possibility of using pulsed laser ablation of nanosecond duration to modify the surface of a cutting tool after regrinding and restoration. Experimental studies of the resistance characteristics of cutting tools with modified surfaces via laser ablation in air and in liquid have been carried out. It was found that after modifying the surface of cutting plates via laser ablation in air, the wear on the trailing surface of the cutting tool at a processing speed of V = 50 m/min is 8 times less than that of the untreated one, the build-up is 20 times less. The wear of the trailing surface of the plates at V = 70 m/min is 2 times less than that of the untreated sample. The resistance studies show surface modification of the cutting tool increases the tool life of the remanufactured tool, overall tool life and savings in tool costs.

Sign in / Sign up

Export Citation Format

Share Document