scholarly journals Physical and Mechanical Properties of Heat Treated Daniella oliveri (Africa Balsam Tree) Wood

2019 ◽  
pp. 1-9 ◽  
Author(s):  
Ebenezer Adeyemi Iyiola ◽  
Babatola Olufemi ◽  
Victoria Olubukola Oyerinde ◽  
J. M. Owoyemi ◽  
Ayanleye Samuel
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Compressive Strength ◽  
Study Design ◽  
Dimensional Stability ◽  
Treated Wood ◽  
Physical And Mechanical Properties ◽  
Thermal Modification ◽  
Average Weight ◽  
Direction Parallel

Aims: This work investigated the effect of thermal modification on some of the physical properties and mechanical properties of Daniella oliveri wood. Study Design: The study design used for this experiment was 3 x4 Factorial experiment in Completely Randomized Design. Place and Duration of Study: The study was conducted at the Federal University of Technology, Akure wood laboratory and the study lasted for 6 months. Methodology: Wood samples were thermally treated at the temperature of 120, 140, 160 and 180°C, for different durations of 1, 1.5 and 2 hours in a muffle furnace. The planks were air-dried to reduce the moisture content and then machined into the required dimensions in the direction parallel to grain with a circular saw. Thirty-nine defect-free samples of dimensions 20 mm × 20 mm × 60 mm were prepared for dimensional stability and compression test, static bending tests and the hardness tests to make a total of 117 samples. Results: The result showed that the average weight loss of the treated wood samples varied from 3.79% at 120°C for 1 hour to 7.51% at 180°C for 2 hours. The treatment led to reduction in density from 528 to 459 kg/m3 at 180°C for 2 hours. The heat treatment also led to reduction in water absorption and volumetric swelling of the treated samples. The mean value for Modulus of elasticity (MOE) ranges from 2.17x103 N/mm2 to 2.96 x 103 N/mm2 for the treated samples while the untreated was 2.22x103 N/mm2. Heat treatment brought about improvement in the maximum compressive strength and the Janka hardness parallel to the grain of wood samples. The value of compressive strength increased from 26.58 N/mm2 to 41.71 N/mm2 and hardness from 69.24 N to 75.5 N. It can therefore be concluded that thermal modification greatly enhanced the dimensional stability and mechanical properties of wood samples.

scholarly journals New Perspective on Wood Thermal Modification: Relevance between the Evolution of Chemical Structure and Physical-Mechanical Properties, and Online Analysis of Release of VOCs

Polymers ◽  
2019 ◽  
Vol 11 (7) ◽  
pp. 1145 ◽  
Author(s):  
Jiajia Xu ◽  
Yu Zhang ◽  
Yunfang Shen ◽  
Cong Li ◽  
Yanwei Wang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Dimensional Stability ◽  
Chemical Structure ◽  
Low Cost ◽  
Physical And Mechanical Properties ◽  
Decay Resistance ◽  
Thermal Modification ◽  
Infrared Spectrometry ◽  
Dominant Component ◽  
New Perspective

Thermal modification (TM) is an ecological and low-cost pretreated method to improve the dimensional stability and decay resistance of wood. This study systematically investigates the relevance between the evolution of chemical structure and the physical and mechanical properties during wood thermal modification processes. Moreover, the volatility of compounds (VOCs) was analyzed using a thermogravimetric analyzer coupled with Fourier transform infrared spectrometry (TGA-FTIR) and a pyrolizer coupled with gas chromatography/mass spectrometer (Py-GC/MS). With an increase of TM temperature, the anti-shrink efficiency and contact angle increased, while the equilibrium moisture content decreased. This result indicates that the dimensional stability improved markedly due to the reduction of hydrophilic hydroxyl (–OH). However, a slight decrease of the moduli of elasticity and of rupture was observed after TM due to the thermal degradation of hemicellulose and cellulose. Based on a TGA-FTIR analysis, the small molecular gaseous components were composed of H2O, CH4, CO2, and CO, where H2O was the dominant component with the highest absorbance intensity, i.e., 0.008 at 200 °C. Based on the Py-GC/MS analysis, the VOCs were shown to be mainly composed of acids, aldehydes, ketones, phenols, furans, alcohols, sugars, and esters, where acids were the dominant compounds, with a relative content of 37.05−42.77%.

Physical and Mechanical Properties of Five Heat-Treated Hardwood Species

2012 ◽  
Vol 472-475 ◽  
pp. 1132-1134
Author(s):  
Jin Sun ◽  
Xiao Bo Wang ◽  
Xiao Jing Wang ◽  
Yan Lin ◽  
Zhen Zhong Gao
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Dimensional Stability ◽  
Negative Impact ◽  
Physical And Mechanical Properties ◽  
Betula Platyphylla ◽  
Fraxinus Mandshurica ◽  
Hardwood Species ◽  
Heat Treated ◽  
Betula Platyphylla Suk

Five hardwood species (Schima superba Gardn, kapur( Dryobalanops sp.), ash (Fraxinus mandshurica Rupr.), birch(Betula platyphylla Suk.), tauari (Couratari sp.)) were conducted the Heat treatment at 185°C.. The results indicated that the dimensional stability, modulus of elasticity (MOE) increased greatly while the wettability decreased after treatment. There was a negative impact of heat treatment on MORs.

scholarly journals Dimensional stability, fungal resistance and mechanical properties of radiata pine after combined thermo-mechanical compression and oil heat-treatment

Holzforschung ◽  
2016 ◽  
Vol 70 (8) ◽  
pp. 793-800 ◽  
Author(s):  
Manoj Kumar Dubey ◽  
Shusheng Pang ◽  
Shakti Chauhan ◽  
John Walker
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Dimensional Stability ◽  
Linseed Oil ◽  
Treated Wood ◽  
Untreated Wood ◽  
Radiata Pine ◽  
Fungal Resistance ◽  
Compression Set ◽  
Decay Test

Abstract The dimensional stability and mechanical properties of radiata pine (Pinus radiata) has been investigated after thermo-mechanically compression (TMC) followed by oil heat-treatment (OHT). Wood specimens were first compressed in the radial direction then heat-treated in a linseed oil bath at 160–210°C. Spring-back percentage, water repellence efficiencies, and compression set recovery percentage were determined as indicators of dimensional stability. The resistance of treated wood against a brown rot fungi was assessed based on an accelerated laboratory fungal decay test. Strength, stiffness and hardness were determined as a function of different treatment parameters. After TMC, high compression set (39%) was achieved without any surface checks and cracks. Specimens undergoing TMC followed by OHT showed relatively less swelling and low compression set recovery under high moisture conditions. The fungal resistance of wood after TMC+OHT slightly increased compared to untreated wood and TMC wood. The mechanical properties of TMC+OHT wood were inferior to those of TMC wood.

scholarly journals Selected Physical and Mechanical Properties of Microwave Heat Treated Rubberwood (Hevea brasiliensis)

2020 ◽  
Vol 10 (18) ◽  
pp. 6273
Author(s):  
Aujchariya Chotikhun ◽  
Jitralada Kittijaruwattana ◽  
Emilia-Adela Salca ◽  
Salim Hiziroglu
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Electron Microscope ◽  
Dimensional Stability ◽  
Hevea Brasiliensis ◽  
Physical And Mechanical Properties ◽  
Modulus Of Rupture ◽  
Heat Treated ◽  
Temperature Levels ◽  
Microwave Heat

The objectives of this study were to evaluate some of physical and mechanical properties of rubberwood (Hevea brasiliensis) as function of microwave heat treatment process. The specimens were heat treated at three temperature levels of 150 °C, 180 °C, and 220 °C for 20 min in a small microwave oven connected to a computer. Bending characteristics, namely modulus of elasticity (MOE), modulus of rupture (MOR) as well as hardness of the samples were tested. Dimensional stability in the form of swelling and water absorption of the specimens were also determined. Based on the findings in this work it appears that microwave can be used successfully for heat treatment of rubberwood. Overall mechanical properties of the samples were adversely influenced by the treatment. MOE, MOR and hardness values of the samples treated at a temperature of 220 °C had 2.37, 3.69, and 2.12 times reduced than those of control samples, respectively. Dimensional stability of the heat treated samples as a result of 2-h and 24-h water soaking improved. Micrographs take from scanning electron microscope (SEM) and transmission electron microscope (TEM) revealed that certain amount of damage took place in the cellwall of the treated specimens. Overall discoloration on the samples due to microwave heat treatment was found insignificant.

scholarly journals Physical and Mechanical Properties of Thermally-Modified Beech Wood Impregnated with Silver Nano-Suspension and Their Relationship with the Crystallinity of Cellulose

Polymers ◽  
2019 ◽  
Vol 11 (10) ◽  
pp. 1538 ◽  
Author(s):  
Siavash Bayani ◽  
Hamid R. Taghiyari ◽  
Antonios N. Papadopoulos
Keyword(s):  
Mechanical Properties ◽  
Physical Properties ◽  
Low Temperatures ◽  
Beech Wood ◽  
Treated Wood ◽  
Physical And Mechanical Properties ◽  
Thermal Modification ◽  
Crystalline Cellulose ◽  
Cross Linking ◽  
Amorphous Cellulose

The aim of this study was to investigate the physical and mechanical properties of thermally modified beech wood impregnated with silver nano-suspension and to examine their relationship with the crystallinity of cellulose. Specimens were impregnated with a 400 ppm nanosilver suspension (NS); at least, 90% of silver nano-particles ranged between 20 and 100 nano-meters. Heat treatment took place in a laboratory oven at three temperatures, namely 145, 165, and 185 °C. Physical properties and mechanical properties of treated wood demonstrated statistically insignificant fluctuations at low temperatures compared to control specimens. On the other hand, an increase of temperature to 185 °C had a significant effect on all properties. Physical properties (volumetric swelling and water absorption) and mechanical properties (MOR and MOE) of treated wood demonstrated statistically insignificant fluctuations at low temperatures compared to control specimens. This degradation ultimately resulted in significant decrease in MOR, impact strength, and physical properties. However, thermal modification at 185 °C did not seem to cause significant fluctuations in MOE and compression strength parallel to grain. As a consequence of the thermal modification, part of amorphous cellulose was changed to crystalline cellulose. At low temperatures an increased crystallinity caused some of the properties to be improved. Crystallinity also demonstrated a decrease in NS-HT185 in comparison to HT185 treatment. TCr indices in specimens thermally treated at 145 °C revealed a significant increase as a result of impregnation with nanosilver suspension. This improvement in TCr index resulted in a noticeable increase in MOR and MOE values. Other properties did not show significant fluctuations, suggesting that the effect of the increased crystallinity and cross-linking in lignin was more than the negative effect of the low cell-wall polymer degradation caused by thermal modification. Change of amorphous cellulose to crystalline cellulose, as well as cross-linking in lignin, partially ameliorated the negative effects of thermal degradation at higher temperatures and therefore, compression parallel to grain and modulus of elasticity did not decrease significantly. Overall, it can be concluded that increased crystallinity and cross-linking in lignin can compensate for some decreased properties caused by thermal modification, but it would be significantly dependent on the temperature under which modification is carried out. Impregnating specimens with silver nano-suspension prior to thermal modification enhanced the effects of thermal modification as a result of improved thermal conductivity.

scholarly journals Termite Resistance, Chemical and Mechanical Characterization of Paulownia tomentosa Wood before and after Heat Treatment

Forests ◽  
2021 ◽  
Vol 12 (8) ◽  
pp. 1114
Author(s):  
Bruno Esteves ◽  
Helena Ferreira ◽  
Hélder Viana ◽  
José Ferreira ◽  
Idalina Domingos ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
New Species ◽  
Thermal Degradation ◽  
Dimensional Stability ◽  
Treated Wood ◽  
Extractive Content ◽  
Paulownia Tomentosa ◽  
Termite Resistance ◽  
Heat Treated

The introduction of new species in forest management must be undertaken with a degree of care, to help prevent the spread of invasive species. However, new species with higher profitability are needed to increase forest products value and the resilience of rural populations. Paulownia tomentosa has an extremely fast growth. The objective and novelty of this work was to study the potential use of young Paulownia trees grown in Portugal by using heat treatment to improve its properties, thereby allowing higher value applications of the wood. The average chemical composition of untreated and heat-treated wood was determined. The extractive content was determined by successive Soxhlet extraction with dichloromethane (DCM), ethanol and water as solvents. The composition of lipophilic extracts was performed by injection in GC-MS with mass detection. Insoluble and soluble lignin, holocellulose and α-cellulose were also determined. Physical (density and water absorption and dimensional stability) and mechanical properties (bending strength and bending stiffness) and termite resistance was also determined. Results showed that extractive content increased in all solvents, lignin and α-cellulose also increased and hemicelluloses decreased. Compounds derived from the thermal degradation of lignin were found in heat-treated wood extractions. Dimensional stability improved but there was a decrease in mechanical properties. Resistance against termites was better for untreated wood than for heat-treated wood, possibly due to the thermal degradation of some toxic extractives.

scholarly journals Low viscosity melamine urea formaldehyde resin as a bulking agent in reducing formaldehyde emission of treated wood

BioResources ◽  
2020 ◽  
Vol 15 (2) ◽  
pp. 2195-2211
Author(s):  
Rabiatol Adawiah Mohd Ali ◽  
Zaidon Ashaari ◽  
Seng Hua Lee ◽  
Mohd Khairun Anwar Uyup ◽  
Edi Suhaimi Bakar ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Dimensional Stability ◽  
Urea Formaldehyde ◽  
Treated Wood ◽  
Physical And Mechanical Properties ◽  
Formaldehyde Emission ◽  
Wood Products ◽  
Formaldehyde Resin ◽  
Low Viscosity ◽  
Resin Impregnation

Melamine urea formaldehyde (MUF) resin impregnation followed by heat compression is a prominent method in improving mechanical properties and dimensional stability of wood. In addition, melamine is reactive to formaldehyde, and therefore able to reduce the free formaldehyde of the treated wood. This study aimed to produce compressed sesenduk (Endospermum diadenum) wood with low formaldehyde emission using low viscosity MUF resin. The effects of treatment efficiency on the physical and mechanical properties of the wood products were evaluated. The experimental design included impregnation of sesenduk strips with 20% and 30% MUF at five different formulations. Then, it was pre-cured at a temperature of 70 °C for 90 min, followed by hot compression at 140 °C with the compression ratio of 80%. The optimum treatment combination was determined through treatability, mechanical strength, dimensional stability, and formaldehyde emission. It was also compared to other treatments, including impregnation without further compression using formulated MUF and commercial MUF. The results revealed that F4 MUF, which consisted of 30% melamine, 50% formaldehyde, and 20% urea, was the optimal MUF formulation that resulted in low formaldehyde emission and acceptable physical and mechanical properties.

PEMANFAATAN KAYU AKASIA MANGIUM (Acacia mangium Willd) UNTUK MEBEL

2012 ◽  
Vol 4 (1) ◽  
pp. 1
Author(s):  
Djoko Purwanto
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Physical Properties ◽  
Treatment Process ◽  
Acacia Mangium ◽  
Physical And Mechanical Properties ◽  
Wood Fibers ◽  
Test Parameters ◽  
Mechanical And Physical Properties ◽  
Scale Scores

Timber Acacia mangium (Acacia mangium, Willd) for Furniture. The study aims to determine the mechanical and physical properties and the decorative value (color and fiber) wood of acacia mangium with using finishing materials. This type of finishing material used is ultran lasur natural dof ,ultran lasur classic teak, aqua politur clear dof, aqua politur akasia dan aqua politur cherry. After finishing the wood is stored for 3 months. Test parameters were observed, namely, physical and mechanical properties of wood, adhesion of finishing materials, color and appearance of the fiber, and timber dimensions expansion. The results showed that the mechanical physical properties of acacia wood qualified SNI. 01-0608-89 about the physical and mechanical properties of wood for furniture, air dry the moisture content from 13.78 to 14.89%, flexural strength from 509.25 to 680.50 kg/cm2, and compressive strength parallel to fiber 342.1 - 412.9 kg/cm2. Finishing the treatment process using five types of finishing materials can increase the decorative value (color and fiber) wood. Before finishing the process of acacia mangium wood has the appearance of colors and fibers and less attractive (scale scores 2-3), after finishing acacia wood fibers have the appearance of colors and interesting and very interesting (scale 4-5).Keywords: mangium wood, mechanical properties, decorative value, finishing, furniture.

scholarly journals Enhancing Density-Based Mining Waste Alkali-Activated Foamed Materials Incorporating Expanded Cork

CivilEng ◽  
2021 ◽  
Vol 2 (2) ◽  
pp. 523-540
Author(s):  
Imed Beghoura ◽  
Joao Castro-Gomes
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Pore Size ◽  
Physical And Mechanical Properties ◽  
Critical Parameters ◽  
Porous Structures ◽  
Foaming Agent ◽  
Al Powder ◽  
Highly Porous ◽  
Alkali Activated

This study focuses on the development of an alkali-activated lightweight foamed material (AA-LFM) with enhanced density. Several mixes of tungsten waste mud (TWM), grounded waste glass (WG), and metakaolin (MK) were produced. Al powder as a foaming agent was added, varying from 0.009 w.% to 0.05 w.% of precursor weight. Expanded granulated cork (EGC) particles were incorporated (10% to 40% of the total volume of precursors). The physical and mechanical properties of the foamed materials obtained, the effects of the amount of the foaming agent and the percentage of cork particles added varying from 10 vol.% to 40% are presented and discussed. Highly porous structures were obtained, Pore size and cork particles distribution are critical parameters in determining the density and strength of the foams. The compressive strength results with different densities of AA-LFM obtained by modifying the foaming agent and cork particles are also presented and discussed. Mechanical properties of the cured structure are adequate for lightweight prefabricated building elements and components.

Impact of Chemical Modification on the Physical and Mechanical Properties of Tropical Wood Material

2012 ◽  
Vol 576 ◽  
pp. 314-317
Author(s):  
Sinin Hamdan ◽  
M. Saiful Islam
Keyword(s):  
Mechanical Properties ◽  
Diazonium Salt ◽  
Treated Wood ◽  
Coupling Reaction ◽  
Physical And Mechanical Properties ◽  
Modulus Of Rupture ◽  
Ft Ir ◽  
Ir Analysis ◽  
D Values ◽  
Benzene Diazonium

Five types of selected tropical light hardwoods were chemically modified with benzene diazonium salt to improve their physical and mechanical properties. Benzene diazonium salt underwent a coupling reaction with wood which was confirmed through FT-IR analysis. The compressive modulus of the treated wood increased, whereas modulus of rupture was shown to decrease on treatment. The modified wood samples had higher hardness (Shore D) values compared to that of the control ones.

Sign in / Sign up

Export Citation Format

Share Document