Magnetic Immobilization and Growth of Nannochloropsis oceanica and Scenedasmus almeriensis

Microalgae are used in industrial and pharmaceutical applications. Their performance on biological applications may be improved by their immobilization. This study presents a way of cell immobilization using microalgae carrying magnetic properties. Nannochloropsis oceanica and Scenedasmus almeriensis cells were treated enzymatically (cellulase) and mechanically (glass beads), generating protoplasts as a means of incorporation of magnetic nanoparticles. Scanning electron microscopy images verified the successful cell wall destruction for both of the examined microalgae cells. Subsequently, protoplasts were transformed with magnetic nanoparticles by a continuous electroporation method and then cultured on a magnetic surface. Regeneration of transformed protoplasts was optimized using various organic carbon and amino acid supplements. Both protoplast preparation methods demonstrated similar efficiency. Casamino acids, as source of amino acids, were the most efficient compound for N. oceanica protoplasts regeneration in enzymatic and mechanical treatment, while for S. almeriensis protoplasts regeneration, fructose, as source of organic carbon, was the most effective. Protoplasts transformation efficiency values with magnetic nanoparticles after enzymatic or mechanical treatments for N. oceanica and S. almeriensis were 17.8% and 10.7%, and 18.6% and 15.7%, respectively. Finally, selected magnetic cells were immobilized and grown on a vertical magnetic surface exposed to light and without any supplement.

Sputter Deposited Magnetostrictive Layers for SAW Magnetic Field Sensors

For the best possible limit of detection of any thin film-based magnetic field sensor, the functional magnetic film properties are an essential parameter. For sensors based on magnetostrictive layers, the chemical composition, morphology and intrinsic stresses of the layer have to be controlled during film deposition to further control magnetic influences such as crystallographic effects, pinning effects and stress anisotropies. For the application in magnetic surface acoustic wave sensors, the magnetostrictive layers are deposited on rotated piezoelectric single crystal substrates. The thermomechanical properties of quartz can lead to undesirable layer stresses and associated magnetic anisotropies if the temperature increases during deposition. With this in mind, we compare amorphous, magnetostrictive FeCoSiB films prepared by RF and DC magnetron sputter deposition. The chemical, structural and magnetic properties determined by elastic recoil detection, X-ray diffraction, and magneto-optical magnetometry and magnetic domain analysis are correlated with the resulting surface acoustic wave sensor properties such as phase noise level and limit of detection. To confirm the material properties, SAW sensors with magnetostrictive layers deposited with RF and DC deposition have been prepared and characterized, showing comparable detection limits below 200 pT/Hz1/2 at 10 Hz. The main benefit of the DC deposition is achieving higher deposition rates while maintaining similar low substrate temperatures.

Design and first result of combined Langmuir-magnetic probe on J-TEXT tokamak

In order to measure boundary electrostatic and magnetic fluctuations simultaneously, a set of combined Langmuir-magnetic probe (CLMP) has been designed and built on Joint-Texas Experimental Tokamak (J-TEXT). The probe consists of 8 graphite probe pins and a 3D magnetic probe, driven by a mechanical pneumatic device. By means of simulation, the shielding effect of the graphite sleeve on the magnetic fluctuation signal is explored, and the influence of the eddy current was reduced by cutting the graphite sleeve. In the experiment, it has been verified that the mutual inductance of electromagnetic signals can be ignored. And a 70~90kHz electromagnetic mode is observed around the last closed magnetic surface (LCFS). The establishment of CLMP provides data for the exploration of the coupling of electrostatic and magnetic fluctuations.

Novel Permanent Magnetic Surface Work Hardening Process for 60/40 Brass

Surface work hardening is a process of deforming a material surface using a thin layer. It hardens and strengthens the surface while keeping the core relatively soft and ductile to absorb stresses. This study introduces a permanent magnate surface work hardening under two opposite permanent poles of a magnet to investigate its influence on a brass surface. The gap between the brass and the north magnet pole—fixed in the spindle of a vertical machine—was filled with martensitic stainless steel balls. The rotational speed and feed rates were 500–1250 rpm and 6–14 mm min−1, respectively. The novel method improved the surface hardness for all parameters by up to 112%, in favor of high speed, and also increased yield by approximately 10% compared to ground samples. Surface roughness showed higher values for all speed–feed rate combinations compared to the ground sample. Nevertheless, it showed better roughness than other treated conditions with high and low feed rates. The ultimate tensile strength and ductility remained unchanged for all conditions other than the untreated brass. A factorial design and nonlinear regression analysis were performed to predict the microhardness equation and effectiveness of the independent variable—speed and feed rate—for the proposed process.

Regular Nanowire Formation on Fe-Based Metal Glass by Manipulation of Surface Waves

We report the formation of a sole long nanowire structure and the regular nanowire arrays inside a groove on the surface of Fe-based metallic glass upon irradiation of two temporally delayed femtosecond lasers with the identical linear polarization parallel and perpendicular to the groove, respectively. The regular structure formation can be well observed within the delay time of 20 ps for a given total laser fluence of F = 30 mJ/cm2 and within a total laser fluence range of F = 30–42 mJ/cm2 for a given delay time of 5 ps. The structural features, including the unit width and distribution period, are measured on a one-hundred nanometer scale, much less than the incident laser wavelength of 800 nm. The degree of structure regularity sharply contrasts with traditional observations. To comprehensively understand such phenomena, we propose a new physical model by considering the spin angular momentum of surface plasmon and its enhanced inhomogeneous magnetization for the ferromagnetic metal. Therefore, an intensive TE polarized magnetic surface wave is excited to result in the nanometer-scaled energy fringes and the ablative troughs. The theory is further verified by the observation of nanowire structure disappearance at the larger time delays of two laser pulses.

Near-to-Far Field Transformation in FDTD: A Comparative Study of Different Interpolation Approaches

Equivalence theorems in electromagnetic field theory stipulate that farfield radiation pattern/scattering profile of a source/scatterer can be evaluated from fictitious electric and magnetic surface currents on an equivalent imaginary surface enclosing the source/scatterer. These surface currents are in turn calculated from tangential (to the equivalent surface) magnetic and electric fields, respectively. However, due to the staggered-in-space placement of electric and magnetic fields in FDTD Yee cell, selection of a single equivalent surface harboring both tangential electric and magnetic fields is not feasible. The work-around is to select a closed surface with tangential electric (or magnetic) fields and interpolate the neighboring magnetic (or electric) fields to bring approximate magnetic (or electric) fields onto the same surface. Interpolation schemes available in the literature include averaging, geometric mean and the mixed-surface approach. In this work, we compare FDTD farfield scattering profiles of a dielectric cube calculated from surface currents that are obtained using various interpolation techniques. The results are benchmarked with those obtained from integral equation solvers available in the commercial packages FEKO and HFSS.