scholarly journals Study on Evaluation Indexes of Surgical Manipulations with a Stereoscopic Endoscope

2004 ◽  
pp. 1083-1084
Author(s):  
Yasushi Yamauchi ◽  
Kazuhiko Shinohara
Keyword(s):  
Evaluation Indexes ◽  
Surgical Manipulations

PARAMETER OPTIMIZATION AND EXPERIMENTAL RESEARCH ON THE HAMMER MILL 锤片式粉碎机参数优化与试验研究

2020 ◽  
pp. 341-350
Author(s):  
Di Wang ◽  
Changbin He ◽  
Haiqing Tian ◽  
Liu Fei ◽  
Zhang Tao ◽  
...  
Keyword(s):  
Moisture Content ◽  
Orthogonal Experiment ◽  
Electricity Consumption ◽  
Spindle Speed ◽  
Hammer Mill ◽  
Factors Affecting ◽  
Evaluation Indexes ◽  
Grain Moisture ◽  
Validation Experiment ◽  
Corn Grain

Low productivity and high electricity consumption are considered problems of the hammer mill, which is widely used in current feed production. In this paper, the mechanical properties of corn grain ground by a hammer mill were analysed, and the key factors affecting the performance of the hammer mill were determined. The single-factor experiment and three-factor, three-level quadratic regression orthogonal experiment were carried out with the spindle speed, corn grain moisture content and number of hammers as experimental factors and the productivity and electricity consumption per ton as evaluation indexes. The results showed that the order of influence on the productivity was spindle speed > corn grain moisture content > number of hammers and that the order of influence on the electricity consumption per ton was corn grain moisture content > spindle speed > number of hammers. The parameters were optimized based on the response surface method with the following results: the spindle speed was 4306 r/min, the corn grain moisture content was 10%, and the number of hammers was 24. The validation experiment was carried out with the optimal parameters’ combination. The productivity and electricity consumption per ton were 988.12 kg/h and 5.37 kW·h/t, respectively, which were consistent with the predicted results of the model.

Dynamic Performance of High-Speed Electric Multiple Unit within Multi-Body System Simulation

2019 ◽  
Vol 12 (4) ◽  
pp. 339-349
Author(s):  
Junguo Wang ◽  
Daoping Gong ◽  
Rui Sun ◽  
Yongxiang Zhao
Keyword(s):  
High Speed ◽  
Rapid Development ◽  
Dynamic Performance ◽  
Body System ◽  
High Speed Railway ◽  
Evaluation Indexes ◽  
Actual Operation ◽  
Multiple Unit ◽  
The Stability ◽  
Multi Body

Background: With the rapid development of the high-speed railway, the dynamic performance such as running stability and safety of the high-speed train is increasingly important. This paper focuses on the dynamic performance of high-speed Electric Multiple Unit (EMU), especially the dynamic characteristics of the bogie frame and car body. Various patents have been discussed in this article. Objective: To develop the Multi-Body System (MBS) model of EMU, verify whether the dynamic performance meets the actual operation requirements, and provide some useful information for dynamics and structural design of the proposed EMU. Methods: According to the technical characteristics of a typical EMU, a MBS model is established via SIMPACK, and the measured data of China high-speed railway is taken as the excitation of track random irregularity. To test the dynamic performance of the EMU, including the stability and safety, some evaluation indexes such as wheel-axle lateral forces, wheel-axle lateral vertical forces, derailment coefficients and wheel unloading rates are also calculated and analyzed in detail. Results: The MBS model of EMU has better dynamic performance especially curving performance, and some evaluation indexes of the stability and safety have also reached China’s high-speed railway standards. Conclusion: The effectiveness of the proposed MBS model is verified, and the dynamic performance of the MBS model can meet the design requirements of high-speed EMU.

scholarly journals Subjective Product Evaluation System Based on Kansei Engineering and Analytic Hierarchy Process

Symmetry ◽  
2020 ◽  
Vol 12 (8) ◽  
pp. 1340 ◽  
Author(s):  
Yaxue Zuo ◽  
Zhenya Wang
Keyword(s):  
Evaluation System ◽  
Comprehensive Evaluation ◽  
Subjective Evaluation ◽  
Reliability And Validity ◽  
Objective Evaluation ◽  
Product Evaluation ◽  
Kansei Engineering ◽  
Analytic Hierarchy ◽  
Evaluation Indexes ◽  
Hierarchy Process

Product evaluation is very important for product improvement and development, and subjective product evaluation determines customer’s evaluation of products to some extent, so the purpose of this study is to establish a reasonable subjective product evaluation system. In this study, we comprehensively determine the evaluation indexes based on Kansei engineering (KE), establish an overall product evaluation system by using analytic hierarchy process (AHP), and establish the subjective product evaluation system by classifying the evaluation indexes in the overall product evaluation system into “objective evaluation index” and “subjective evaluation index”, removing the objective evaluation indexes, and retaining the subjective evaluation indexes. Additionally, we select some modern chairs as experimental samples to verify the reliability and validity of this subjective product evaluation system by means of questionnaires. The experimental results show that, in this subjective product evaluation system, the subjective evaluation of the product is positively correlated with the “favorite” level of the product in comprehensive evaluation, and negatively correlated with the “least favorite” level of the product in comprehensive evaluation, indicating that this subjective product evaluation system realizes a symmetry between subjective product evaluation and comprehensive product evaluation. Therefore, it can be concluded that this subjective product evaluation system based on KE and AHP proposed in this study has reliability and validity, and can be used for product evaluation to judge the popularity of products and enhance the competitiveness of products.

Comparison of phaco time parameters in eyes with and without glaucoma filtration surgery due to pseudoexfoliation glaucoma

2021 ◽  
pp. 112067212110177
Author(s):  
Ayse Gul Kocak Altintas ◽  
Cagri Ilhan
Keyword(s):  
Clinical Characteristics ◽  
Pseudoexfoliation Glaucoma ◽  
Filtration Surgery ◽  
Glaucoma Filtration Surgery ◽  
Mean Values ◽  
Time Parameters ◽  
The Mean ◽  
Group 2 ◽  
Surgical Manipulations ◽  
Phaco Time

Purpose: To compare the phaco time parameters including ultrasound time (UST), effective phaco time (EPT), and average phaco power (APP) in eyes with pseudoexfoliation glaucoma (PEG) and had or had not glaucoma filtration surgery. Methods: In this retrospective comparative study, Group 1 was constructed with 84 PEG patients who had not operated previously, and Group 2 was constructed with 49 PEG patients who had glaucoma filtration surgery. The mean values of UST, EPT, and APP were compared. The preoperative clinical characteristics and surgical manipulations were also compared. Results: The mean ages and male-to-female ratios of the groups were similar ( p > 0.05, for both). There was no difference in the preoperative clinical characteristics, including biometric values between the groups ( p > 0.05, for all). Some surgical manipulations, including pupillary stretching ( p = 0.004), pupillary membrane peeling ( p = 0.021), iris hook using ( p = 0.041), and capsular tension ring implantation ( p = 0.041), were significantly performed more commonly in Group 2. Although the mean UST and EPT values were similar ( p > 0.05, for both), the mean APP value was significantly lower in Group 2 ( p = 0.011). Conclusion: The lower APP parameter was observed in PEG patients having had glaucoma filtration surgery. Needing more surgical manipulation to overcome poor pupillary dilation and weak zonular instability can be a reason for this result.

Preparation, evaluation, and in vitro release of chitosan-alginate tanshinone self-microemulsifying sustained-release microcapsules

2020 ◽  
pp. 1-9
Author(s):  
Yunhong Wang ◽  
Rong Hu ◽  
Yanlei Guo ◽  
Weihan Qin ◽  
Xiaomei Zhang ◽  
...  
Keyword(s):  
Drug Release ◽  
Sustained Release ◽  
Release Rate ◽  
Orthogonal Design ◽  
Drug Loading ◽  
In Vitro Release ◽  
Core Material ◽  
Evaluation Indexes ◽  
Vitro Release

OBJECTIVE: In this study we explore the method to prepare tanshinone self-microemulsifying sustained-release microcapsules using tanshinone self-microemulsion as the core material, and chitosan and alginate as capsule materials. METHODS: The optimal preparation technology of chitosan-alginate tanshinone self-microemulsifying sustained-release microcapsules was determined by using the orthogonal design experiment and single-factor analysis. The drug loading and entrapment rate were used as evaluation indexes to assess the quality of the drug, and the in vitro release rate was used to evaluate the drug release performance. RESULTS: The best technology of chitosan-alginate tanshinone self-microemulsifying sustained-release microcapsules is as follows: the concentration of alginate is 1.5%, the ratio of tanshinone self-microemulsion volume to alginate volume to chitosan mass is 1:1:0.5 (ml: ml: g), and the best concentration of calcium chloride is 2.0%. To prepare the microcapsules using this technology, the drug loading will be 0.046%, the entrapment rate will be 80.23%, and the 24-hour in vitro cumulative release rate will be 97.4%. CONCLUSION: The release of the microcapsules conforms to the Higuchi equation and the first-order drug release model and has a good sustained-release performance.

scholarly journals Role of PEG35, Mitochondrial ALDH2, and Glutathione in Cold Fatty Liver Graft Preservation: An IGL-2 Approach

2021 ◽  
Vol 22 (10) ◽  
pp. 5332
Author(s):  
Raquel G. Bardallo ◽  
Rui Teixeira da Silva ◽  
Teresa Carbonell ◽  
Emma Folch-Puy ◽  
Carlos Palmeira ◽  
...  
Keyword(s):  
Nitric Oxide ◽  
Fatty Liver ◽  
Liver Graft ◽  
Suitable Alternative ◽  
Graft Preservation ◽  
Preservation Solutions ◽  
Microcirculatory Disturbances ◽  
Organ Recovery ◽  
Surgical Manipulations

The total damage inflicted on the liver before transplantation is associated with several surgical manipulations, such as organ recovery, washout of the graft, cold conservation in organ preservation solutions (UW, Celsior, HTK, IGL-1), and rinsing of the organ before implantation. Polyethylene glycol 35 (PEG35) is the oncotic agent present in the IGL-1 solution, which is an alternative to UW and Celsior solutions in liver clinical transplantation. In a model of cold preservation in rats (4 °C; 24 h), we evaluated the effects induced by PEG35 on detoxifying enzymes and nitric oxide, comparing IGL-1 to IGL-0 (which is the same as IGL-1 without PEG). The benefits were also assessed in a new IGL-2 solution characterized by increased concentrations of PEG35 (from 1 g/L to 5 g/L) and glutathione (from 3 mmol/L to 9 mmol/L) compared to IGL-1. We demonstrated that PEG35 promoted the mitochondrial enzyme ALDH2, and in combination with glutathione, prevented the formation of toxic aldehyde adducts (measured as 4-hydroxynonenal) and oxidized proteins (AOPP). In addition, PEG35 promoted the vasodilator factor nitric oxide, which may improve the microcirculatory disturbances in steatotic grafts during preservation and revascularization. All of these results lead to a reduction in damage inflicted on the fatty liver graft during the cold storage preservation. In this communication, we report on the benefits of IGL-2 in hypothermic static preservation, which has already been proved to confer benefits in hypothermic oxygenated dynamic preservation. Hence, the data reported here reinforce the fact that IGL-2 is a suitable alternative to be used as a unique solution/perfusate when hypothermic static and preservation strategies are used, either separately or combined, easing the logistics and avoiding the mixture of different solutions/perfusates, especially when fatty liver grafts are used. Further research regarding new therapeutic and pharmacological insights is needed to explore the underlying mitochondrial mechanisms exerted by PEG35 in static and dynamic graft preservation strategies for clinical liver transplantation purposes.

scholarly journals Quantitative Risk Assessment for Deep Tunnel Failure Based on Normal Cloud Model: A Case Study at the ASHELE Copper Mine, China

2021 ◽  
Vol 11 (11) ◽  
pp. 5208
Author(s):  
Jianpo Liu ◽  
Hongxu Shi ◽  
Ren Wang ◽  
Yingtao Si ◽  
Dengcheng Wei ◽  
...  
Keyword(s):  
Risk Assessment ◽  
Large Scale ◽  
Cloud Model ◽  
Quantitative Risk Assessment ◽  
Geological Condition ◽  
Deep Tunnel ◽  
Entropy Weight ◽  
Copper Mine ◽  
Evaluation Indexes ◽  
Metal Mines

The spatial and temporal distribution of tunnel failure is very complex due to geologic heterogeneity and variability in both mining processes and tunnel arrangement in deep metal mines. In this paper, the quantitative risk assessment for deep tunnel failure was performed using a normal cloud model at the Ashele copper mine, China. This was completed by considering the evaluation indexes of geological condition, mining process, and microseismic data. A weighted distribution of evaluation indexes was determined by implementation of an entropy weight method to reveal the primary parameters controlling tunnel failure. Additionally, the damage levels of the tunnel were quantitatively assigned by computing the degree of membership that different damage levels had, based on the expectation normalization method. The methods of maximum membership principle, comprehensive evaluation value, and fuzzy entropy were considered to determine the tunnel damage levels and risk of occurrence. The application of this method at the Ashele copper mine demonstrates that it meets the requirement of risk assessment for deep tunnel failure and can provide a basis for large-scale regional tunnel failure control in deep metal mines.

scholarly journals Ultrasonic dispersion method used in glass polishing experiment

2021 ◽  
Vol 13 (4) ◽  
pp. 168781402110118
Author(s):  
Zenan Chu ◽  
Tao Wang ◽  
Qiang He ◽  
Kai Zhao
Keyword(s):  
Surface Roughness ◽  
Rare Earth ◽  
Surface Morphology ◽  
Ultrasonic Method ◽  
Average Surface Roughness ◽  
Polishing Process ◽  
Ultrasonic Dispersion ◽  
Processing Efficiency ◽  
Average Surface ◽  
Evaluation Indexes

To solve the problems of low processing efficiency and poor glass surface quality when using rare earth polishing powder to grind super-hard K9 glass. The potential, phase structure, surface morphology, and particle size distribution of the nano-rare earth polishing powder were characterized. Compare the evaluation indexes such as polishing efficiency, surface morphology, and contact angle after the polishing process is changed. The results of the comparative study show that the average surface roughness of the glass after heating ultrasonic polishing process is 0.9064 nm, the polishing rate reaches 0.748 μm/min, the average surface roughness of the glass without heating ultrasonic polishing process is 1.3175 nm, and the polishing rate reaches 0.586 μm/min, the ultrasonic assisted polishing process is superior to the conventional polishing process. The heating ultrasonic method provides experimental basis for precise and rapid processing.

scholarly journals Remote Sensing Image Dataset Expansion Based on Generative Adversarial Networks with Modified Shuffle Attention

Sensors ◽  
2021 ◽  
Vol 21 (14) ◽  
pp. 4867
Author(s):  
Lu Chen ◽  
Hongjun Wang ◽  
Xianghao Meng
Keyword(s):  
Remote Sensing ◽  
Neural Networks ◽  
Image Processing ◽  
Remote Sensing Image ◽  
Generative Adversarial Networks ◽  
Generative Adversarial Network ◽  
Evaluation Indexes ◽  
Adversarial Network ◽  
Remote Sensing Image Processing ◽  
Data Expansion

With the development of science and technology, neural networks, as an effective tool in image processing, play an important role in gradual remote-sensing image-processing. However, the training of neural networks requires a large sample database. Therefore, expanding datasets with limited samples has gradually become a research hotspot. The emergence of the generative adversarial network (GAN) provides new ideas for data expansion. Traditional GANs either require a large number of input data, or lack detail in the pictures generated. In this paper, we modify a shuffle attention network and introduce it into GAN to generate higher quality pictures with limited inputs. In addition, we improved the existing resize method and proposed an equal stretch resize method to solve the problem of image distortion caused by different input sizes. In the experiment, we also embed the newly proposed coordinate attention (CA) module into the backbone network as a control test. Qualitative indexes and six quantitative evaluation indexes were used to evaluate the experimental results, which show that, compared with other GANs used for picture generation, the modified Shuffle Attention GAN proposed in this paper can generate more refined and high-quality diversified aircraft pictures with more detailed features of the object under limited datasets.

Design of combined brake system for light weight scooters

2021 ◽  
pp. 095440702110240
Author(s):  
Yuan-Ting Lin ◽  
Chyuan-Yow Tseng ◽  
Jao-Hwa Kuang ◽  
Yeong-Maw Hwang
Keyword(s):  
Ride Comfort ◽  
Brake System ◽  
Force Distribution ◽  
Test Results ◽  
Systematic Method ◽  
Braking Performance ◽  
Evaluation Indexes ◽  
Low Costs ◽  
Braking Force ◽  
Good Agreement

The combined brake system (CBS) is a mechanism that links the front and rear brakes for scooters. For two-wheeled scooters, a CBS with appropriate braking force distribution can reduce the risk of crashing accidents due to insufficient driving proficiency. The design of the braking force distribution for a CBS is challenging to the designer because it has to fulfill many requirements such as braking performance, ride comfort, reliability, and low costs. This paper proposes a systematic method to optimize the parameters of CBS. The evaluation indexes for the design are first discussed. The steps to determine the critical parameter to meet the indexes and a method to predict braking performance are developed. Finally, driving tests are carried out to verify the effectiveness of the proposed method. Experimental results showed that the deceleration of the tested scooter equipped with the designed CBS achieves an average mean fully developed deceleration (MFDD) of 5.246 m/s2, higher than the homologation requirement. Furthermore, the proposed method’s prediction of braking performance is in good agreement with the test results, with errors <1%.

Sign in / Sign up

Export Citation Format

Share Document