Interfacial Adhesion, Interphase Formation and Mechanical Properties of Single Fibre Polymer Based Composites

1990 ◽  
pp. 561-567 ◽  
Author(s):  
J. Schultz ◽  
M. Nardin
Keyword(s):  
Mechanical Properties ◽  
Interfacial Adhesion ◽  
Single Fibre ◽  
Adhesion Interphase

An Energy-Based interpretation of Interfacial Adhesion from Single Fibre Composite Fragmentation Testing

1993 ◽  
Vol 2 (5) ◽  
pp. 096369359300200 ◽  
Author(s):  
H.D. Wagner ◽  
S. Ling
Keyword(s):  
Interfacial Adhesion ◽  
Mechanical Characteristics ◽  
Interfacial Shear Strength ◽  
Fibre Composite ◽  
Stress Transfer ◽  
Single Fibre ◽  
Transfer Length ◽  
Fragmentation Test ◽  
Energy Balance Approach ◽  
Fibre Matrix

An energy balance approach is proposed for the single fibre composite (or fragmentation) test, by which the degree of fibre-matrix bonding is quantified by means of the interfacial energy, rather than the interfacial shear strength, as a function of the fibre geometrical and mechanical characteristics, the stress transfer length, and the debonding length. The validity of the approach is discussed using E-glass fibres embedded in epoxy, both in the dry state and in the presence of hot distilled water.

scholarly journals Mechanical Properties and Bioactivity of Poly(Lactic Acid) Composites Containing Poly(Glycolic Acid) Fiber and Hydroxyapatite Particles

Nanomaterials ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 249
Author(s):  
Han-Seung Ko ◽  
Sangwoon Lee ◽  
Doyoung Lee ◽  
Jae Young Jho
Keyword(s):  
Mechanical Properties ◽  
Lactic Acid ◽  
Flexural Strength ◽  
Interfacial Adhesion ◽  
Glycolic Acid ◽  
Compact Bone ◽  
Poly Lactic Acid ◽  
Coupling Reactions ◽  
The Poor ◽  
Human Compact Bone

To enhance the mechanical strength and bioactivity of poly(lactic acid) (PLA) to the level that can be used as a material for spinal implants, poly(glycolic acid) (PGA) fibers and hydroxyapatite (HA) were introduced as fillers to PLA composites. To improve the poor interface between HA and PLA, HA was grafted by PLA to form HA-g-PLA through coupling reactions, and mixed with PLA. The size of the HA particles in the PLA matrix was observed to be reduced from several micrometers to sub-micrometer by grafting PLA onto HA. The tensile and flexural strength of PLA/HA-g-PLA composites were increased compared with those of PLA/HA, apparently due to the better dispersion of HA and stronger interfacial adhesion between the HA and PLA matrix. We also examined the effects of the length and frequency of grafted PLA chains on the tensile strength of the composites. By the addition of unidirectionally aligned PGA fibers, the flexural strength of the composites was greatly improved to a level comparable with human compact bone. In the bioactivity tests, the growth of apatite on the surface was fastest and most uniform in the PLA/PGA fiber/HA-g-PLA composite.

Effect of Heat Setting Methods on Structures and Properties of High Strength Polyvinyl Alcohol Fibre

2015 ◽  
Vol 815 ◽  
pp. 643-648
Author(s):  
Yin Zhu ◽  
Jiong Xin Zhao
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Polyvinyl Alcohol ◽  
Setting Time ◽  
High Strength ◽  
Single Fibre ◽  
X Ray Diffraction ◽  
Heat Setting ◽  
Heat Treated ◽  
Setting Process

The effect of heat setting methods on the structures and mechanical properties of high strength polyvinyl alcohol (PVA) fibre is studied in this article. The microstructure and mechanical properties of heat treated PVA fibre is investigated by scanning electron microscopy (SEM), X-ray diffraction (XRD), and single fibre electronic tensile strength tester. Results show that the heat setting method with constant tension is a good heat setting method which can largely enhance the tensile strength of PVA fibre. During the heat setting process, the mechanical properties of PVA fibre are greatly affected by the temperature, tension and setting time. When the temperature is 220°C, tension is 5cN/dtex and setting time is 90sec, the tensile strength of PVA fibre increases from 12.0cN/dtex to 16.4cN/dtex in compare with the PVA fibre without heat setting

Effect of graphite and silicon carbide fillers on mechanical properties of PA6 polymer composites

2017 ◽  
Vol 37 (6) ◽  
pp. 547-557 ◽  
Author(s):  
Sekaran Sathees Kumar ◽  
Ganesan Kanagaraj
Keyword(s):  
Mechanical Properties ◽  
Silicon Carbide ◽  
Polymer Composites ◽  
Interfacial Adhesion ◽  
Hybrid Composites ◽  
Fracture Morphology ◽  
Tensile Fracture ◽  
Injection Molded ◽  
The Individual

Abstract In this paper, the combined effect of different weight percentages of silicon carbide (SiC) and graphite (Gr) reinforcement on the mechanical properties of polyamide (PA6) composite is studied. Test specimens of pure PA6, 85 wt% PA6+10 wt% SiC+5 wt% Gr and 85 wt% PA6+5 wt% SiC+10 wt% Gr are prepared using an injection molding machine. The tensile, impact, hardness, morphology and thermal properties of the injection molded composites were investigated. The obtained results showed that mechanical properties, such as tensile and impact strength and modulus of the PA6 composites, were significantly higher than the pure PA6, and hybridization with silicon carbide and graphite further enhanced the performance properties, as well as the thermal resistance of the composites. The tensile fracture morphology and the characterization of PA6 polymer composites were observed by scanning electron microscope (SEM) and Fourier transform infrared spectroscopic methods. SEM observation of the fracture surfaces showed the fine dispersion of SiC and Gr for strong interfacial adhesion between fibers and matrix. The individual and combined reinforcing effects of silicon carbide and graphite on the mechanical properties of PA6 hybrid composites were compared and interpreted in this study. Improved mechanical properties were observed by the addition of small amount of SiC and Gr concurrently reinforced with the pure PA6. Finally, thermogravimetric analysis showed that the heat resistance of the composites tended to increase with increasing silicon carbide and graphite content simultaneously.

scholarly journals Physical and Chemical Modifications of Plant Fibres for Reinforcement in Cementitious Composites

2019 ◽  
Vol 2019 ◽  
pp. 1-18 ◽  
Author(s):  
R. Ahmad ◽  
R. Hamid ◽  
S. A. Osman
Keyword(s):  
Mechanical Properties ◽  
Interfacial Adhesion ◽  
Moisture Absorption ◽  
Surface Modifications ◽  
Future Research ◽  
Cementitious Composites ◽  
Chemical Surface ◽  
Plant Fibre ◽  
Physical And Chemical ◽  
Fibre Matrix

This paper highlights the physical and chemical surface modifications of plant fibre (PF) for attaining suitable properties as reinforcements in cementitious composites. Untreated PF faces insufficient adhesion between the fibres and matrix due to high levels of moisture absorption and poor wettability. These conditions accelerate degradation of the fibre in the composite. It is also essential to reduce the risk of hydrophilic PF conditions with surface modification, to enhance the mechanical properties of the fibres. Fibres that undergo chemical and physical modifications had been proven to exhibit improved fibre-matrix interfacial adhesion in the composite and contribute to better composite mechanical properties. This paper also gives some recommendations for future research on chemical and physical modifications of PF.

scholarly journals Surface Modification of Carbon Fibers by Grafting PEEK-NH2 for Improving Interfacial Adhesion with Polyetheretherketone

Materials ◽  
2019 ◽  
Vol 12 (5) ◽  
pp. 778 ◽  
Author(s):  
Elwathig. Hassan ◽  
Tienah. Elagib ◽  
Hafeezullah Memon ◽  
Muhuo Yu ◽  
Shu Zhu
Keyword(s):  
Mechanical Properties ◽  
Shear Strength ◽  
Carbon Fibers ◽  
Interfacial Adhesion ◽  
Mechanical Analysis ◽  
Interlaminar Shear Strength ◽  
Thermoplastic Composites ◽  
Negative Effects ◽  
Covalent Bonds ◽  
Interlaminar Shear

Due to the non-polar nature and low wettability of carbon fibers (CFs), the interfacial adhesion between CFs and the polyetheretherketone (PEEK) matrix is poor, and this has negative effects on the mechanical properties of CF/PEEK composites. In this work, we established a modification method to improve the interface between CFs and PEEK based chemical grafting of aminated polyetheretherketone (PEEK-NH2) on CFs to create an interfacial layer which has competency with the PEEK matrix. The changed chemical composition, surface morphology, surface energy, and interlaminar shear strength were investigated. After grafting, the interlaminar shear strength (ILSS) was improved by 33.4% due to the covalent bonds in the interface region, as well as having good compatibility between the interface modifier and PEEK. Finally, Dynamic Mechanical Analysis (DMA) and Scanning Electron Microscopy (SEM) observation also confirmed that the properties of the modified CF/PEEK composites interface were enhanced. This work is, therefore, a beneficial approach towards enhancing the mechanical properties of thermoplastic composites by controlling the interface between CFs and the PEEK matrix.

Toughening of Polypropylene Highly Filled with Aluminum Hydroxide

2005 ◽  
Vol 13 (2) ◽  
pp. 139-150 ◽  
Author(s):  
Zhanpai Su ◽  
Pingkai Jiang ◽  
Qiang Li ◽  
Ping Wei ◽  
Yong Zhang
Keyword(s):  
Mechanical Properties ◽  
Tensile Properties ◽  
Aluminum Hydroxide ◽  
Interfacial Adhesion ◽  
Ethylene Propylene Diene Monomer ◽  
The Matrix ◽  
Izod Impact ◽  
Rubbery Phase ◽  
Rubber Phase ◽  
Toughening Agent

The flame retardant and mechanical properties of polypropylene (PP), highly filled with aluminum hydroxide (Al(OH)3) and toughened with ethylene propylene diene monomer (EPDM) and zinc neutralized sulfated EPDM ionomer (Zn-S-EPDM), were studied along with their morphology. The PP matrix when highly filled with Al(OH)3 particles can achieve an adequate level of flame retardancy, but there is a decrease in the mechanical properties because of inadequate adhesion between the Al(OH)3 particles and the PP matrix and the strong tendency of the filler to agglomerate. The rubber incorporated in the PP/Al(OH)3 composites has two roles: as compatibilizer and toughening agent. Although ordinary EPDM significantly improves the Izod impact strength of the composites, the tensile properties are much worse because of the weak interfacial adhesion between the modifier and the matrix. Using Zn-S-EPDM instead EPDM, the tensile properties are much improved with only a slight decrease in toughness, because of improvements in the interfacial adhesion between modifier and matrix. SEM micrographs show that the rubber phase is dispersed in the continuous PP matrix and that most Al(OH)3 particles are uniformly distributed in the rubbery phase. Larger, obviously rubbery, domains can be seen in the PP/EPDM/Al(OH)3 ternary composites. Much finer rubbery domains were found in the PP/Zn-S-EPDM/Al(OH)3 composites.

scholarly journals Patterned Metal/Polymer Composite Film with Good Mechanical Stability and Repeatability for Flexible Electronic Devices Using Nanoimprint Technology

Micromachines ◽  
2019 ◽  
Vol 10 (10) ◽  
pp. 651
Author(s):  
Xu Zheng ◽  
Qing Wang ◽  
Jinjin Luan ◽  
Yao Li ◽  
Ning Wang
Keyword(s):  
Mechanical Properties ◽  
Composite Film ◽  
Polymer Composite ◽  
Interfacial Adhesion ◽  
Metal Film ◽  
Mechanical Stability ◽  
Electronic Devices ◽  
Composite Films ◽  
Polymer Composite Film ◽  
Metal Polymer

Mechanical stability and repeatability are significant factors for the application of metal film flexible electronic devices. In this work, patterned metal/polymer composite films with good mechanical stability and repeatability were fabricated through nanoimprint technology. The mechanical properties characteristic of metal/polymer composite films were exhibited by resistance change (ΔR/R0) after cyclic tension and bending loading. It was found that the ΔR/R0 and error line of patterned metal/polymer composite film was far lower than the other control groups for repeated experiments, which indicates that patterned metal film has excellent mechanical properties and repeatability. The double cantilever beam method was employed to measure the interfacial adhesion properties of composite films. The average interfacial adhesion of patterned metal/polymer composite films is shown to be over 2.9 and 2.2 times higher than that of metal film deposited on bare polymer and metal nanowire-treated polymer substrates, respectively.

scholarly journals Effect of Using Hybrid Polypropylene and Glass Fibre on the Mechanical Properties and Permeability of Concrete

Materials ◽  
2019 ◽  
Vol 12 (22) ◽  
pp. 3786 ◽  
Author(s):  
Abubaker A. M. Ahmed ◽  
Yanmin Jia
Keyword(s):  
Mechanical Properties ◽  
Reinforced Concrete ◽  
Glass Fibre ◽  
Single Fibre ◽  
Air Permeability ◽  
Fibre Content ◽  
Peak Performance ◽  
Fibre Reinforced Concrete ◽  
Performance Limit ◽  
Hybrid Fibre

A comprehensive program of experiments consisting of compression, uniaxial compression, direct shear, flexural as well as splitting tensile and air permeability tests were performed to analyse the effect of the level of fibre dosage and the water–cement ratio on the physical properties of hybrid fibre-reinforced concrete (HFRC). Two types of fibres were studied in terms of their effect on the properties of HFRC. The results indicated that the mechanical properties of concrete were significantly improved by increasing the fibre content. However, increasing the percentage fibre content past a certain peak performance limit (0.9% glass fibre (GF) and 0.45% polypropylene fibre (PPF)) led to a decrease in strength compared to reference mixes. Additionally, the incorporation of hybrid fibres yielded an increase in air permeability in the tested specimens. The results showed that the strength-related properties of HFRC were superior to the properties of single fibre-reinforced concrete.

Sign in / Sign up

Export Citation Format

Share Document