Effect of the end clearances in a turbine compressor stage on its efficiency of operation

1979 ◽  
Vol 15 (8) ◽  
pp. 579-582
Author(s):  
V. P. Parafeinik ◽  
F. S. Rekstin ◽  
Yu. A. Bondarenko
Keyword(s):  
Compressor Stage

Studies on Downstream Stator With Rotor Re-Staggering and Forward Sweeping in a Subsonic Axial Compressor Stage

2011 ◽  
Author(s):  
P. V. Ramakrishna ◽  
M. Govardhan
Keyword(s):  
Flow Field ◽  
Computational Model ◽  
Flow Rate ◽  
Total Pressure ◽  
Axial Compressor ◽  
Pressure Rise ◽  
Axial Distance ◽  
Compressor Stage ◽  
Numerical Work ◽  
Stagger Angle

The present numerical work studies the flow field in subsonic axial compressor stator passages for: (a) preceding rotor sweep (b) preceding rotor re-staggering (three stagger angle changes: 0°, +3° and +5°); and (c) stator sweeping (two 20° forward sweep schemes). The following are the motives for the study: at the off-design conditions, compressor rotors are re-staggered to alleviate the stage mismatching by adjusting the rows to the operating flow incidence. Fundamental to this is the understanding of the effects of rotor re-staggering on the downstream component. Secondly, sweeping the rotor stages alters the axial distance between the successive rotor-stator stages and necessitates that the stator vanes must also be swept. To the best of the author’s knowledge, stator sweeping to suit such scenarios has not been reported. The computational model for the study utilizes well resolved hexahedral grids. A commercial CFD package ANSYS® CFX 11.0 was used with standard k-ω turbulence model for the simulations. CFD results were well validated with experiments. The following observations were made: (1) When the rotor passage is closed by re-staggering, with the same mass flow rate and the same stator passage area, stators were subjected to negative incidences. (2) Effect of stator sweeping on the upstream rotor flow field is insignificant. Comparison of total pressure rise carried by the downstream stators suggests that an appropriate redesign of stator is essential to match with the swept rotors. (3) While sweeping the stator is not recommended, axial sweeping is preferable over true sweeping when it is necessary.

Influence of Non-Equilibrium Fluid Properties During Fogging on Intake Duct and Compressor Characteristics

2017 ◽  
Author(s):  
Christoph Günther ◽  
Franz Joos
Keyword(s):  
Relative Humidity ◽  
Gas Turbine ◽  
Thermophysical Properties ◽  
Ambient Air ◽  
Compressor Stage ◽  
Compression Process ◽  
Fluid Properties ◽  
Temperature And Pressure ◽  
Gas Turbine Compressor ◽  
Non Equilibrium

This study reports on numerically calculated thermophysical properties of air passing through a gas turbine compressor after passage through an intake duct affected by wet compression. Case of reference is unaffected ambient air (referenced to as dry scenario) passing through intake duct and compressor. Furthermore, ambient air cooled down by (overspray) fogging (referenced to as wet scenarios) was considered. Acceleration at the end of intake duct causing reduction of static temperature and pressure results in supersaturated fluid properties at inlet to gas turbine compressor. These supersaturated fluid properties are non-equilibrium with saturation level above relative humidity of φ = 1. Entrance of supersaturated fluid into gas turbine compressor can result in condensation within first compressor stage. At the same time delayed impact of evaporative cooling influences compression process.

Performance Prediction for Automotive Turbocharger Compressors

1975 ◽  
Vol 189 (1) ◽  
pp. 557-565 ◽  
Author(s):  
A. Whitfield ◽  
F. J. Wallace
Keyword(s):  
Performance Prediction ◽  
Flow Analysis ◽  
Compressor Stage ◽  
Thermodynamic Models ◽  
Flow Rates ◽  
Design Point ◽  
One Dimensional ◽  
Dimensional Flow ◽  
Performance Map ◽  
The Individual

A procedure to predict the complete performance map of turbocharger centrifugal compressors is presented. This is based on a one-dimensional flow analysis using existing published loss correlations that were available and thermodynamic models to describe the incidence loss and slip factor variation at flow rates which differ from the design point. To predict the losses within the complete compressor stage using a one-dimensional flow procedure, it is necessary to introduce a number of empirical parameters. The uncertainty associated with these empirical parameters is assessed by studying the effect of varying them upon the individual losses and upon the overall predicted performance.

Redesign of a Compressor Stage for a High-Performance Electric Supercharger in a Heavily Downsized Engine

2017 ◽  
Vol 140 (4) ◽  
Author(s):  
Peng Wang ◽  
Mehrdad Zangeneh ◽  
Bryn Richards ◽  
Kevin Gray ◽  
James Tran ◽  
...  
Keyword(s):  
Design Method ◽  
Pressure Ratio ◽  
Compressor Stage ◽  
Impeller Blade ◽  
Guide Vanes ◽  
Inlet Guide Vanes ◽  
Surge Margin ◽  
Stable Operating ◽  
Inverse Design Method ◽  
Ported Shroud

Engine downsizing is a modern solution for the reduction of CO2 emissions from internal combustion engines. This technology has been gaining increasing attention from industry. In order to enable a downsized engine to operate properly at low speed conditions, it is essential to have a compressor stage with very good surge margin. The ported shroud, also known as the casing treatment, is a conventional way used in turbochargers to widen the working range. However, the ported shroud works effectively only at pressure ratios higher than 3:1. At lower pressure ratio, its advantages for surge margin enhancements are very limited. The variable inlet guide vanes are also a solution to this problem. By adjusting the setting angles of variable inlet guide vanes, it is possible to shift the compressor map toward the smaller flow rates. However, this would also undermine the stage efficiency, require extra space for installing the inlet guide vanes, and add costs. The best solution is therefore to improve the design of impeller blade itself to attain high aerodynamic performances and wide operating ranges. This paper reports a recent study of using inverse design method for the redesign of a centrifugal compressor stage used in an electric supercharger, including the impeller blade and volute. The main requirements were to substantially increase the stable operating range of the compressor in order to meet the demands of the downsized engine. The three-dimensional (3D) inverse design method was used to optimize the impeller geometry and achieve higher efficiency and stable operating range. The predicted performance map shows great advantages when compared with the existing design. To validate the computational fluid dynamics (CFD) results, this new compressor stage has also been prototyped and tested. It will be shown that the CFD predictions have very good agreement with experiments and the redesigned compressor stage has improved the pressure ratio, aerodynamic efficiency, choke, and surge margins considerably.

An Investigation of the Stability Enhancement of a Centrifugal Compressor Stage Using a Porous Throat Diffuser

2017 ◽  
Vol 140 (1) ◽  
Author(s):  
Lee Galloway ◽  
Stephen Spence ◽  
Sung In Kim ◽  
Daniel Rusch ◽  
Klemens Vogel ◽  
...  
Keyword(s):  
Centrifugal Compressor ◽  
Compressor Stage ◽  
Vaned Diffuser ◽  
Flow Rates ◽  
Stall Inception ◽  
Centrifugal Compressor Stage ◽  
Operating Range ◽  
Stable Operating ◽  
The Stability ◽  
Circumferential Pressure

The stable operating range of a centrifugal compressor stage of an engine turbocharger is limited at low mass flow rates by aerodynamic instabilities which can lead to the onset of rotating stall or surge. There have been many techniques employed to increase the stable operating range of centrifugal compressor stages. The literature demonstrates that there are various possibilities for adding special treatments to the nominal diffuser vane geometry, or including injection or bleed flows to modify the diffuser flow field in order to influence diffuser stability. One such treatment is the porous throat diffuser (PTD). Although the benefits of this technique have been proven in the existing literature, a comprehensive understanding of how this technique operates is not yet available. This paper uses experimental measurements from a high pressure ratio (PR) compressor stage to acquire a sound understanding of the flow features within the vaned diffuser which affect the stability of the overall compression system and investigate the stabilizing mechanism of the porous throat diffuser. The nonuniform circumferential pressure imposed by the asymmetric volute is experimentally and numerically examined to understand if this provides a preferential location for stall inception in the diffuser. The following hypothesis is confirmed: linking of the diffuser throats via the side cavity equalizes the diffuser throat pressure, thus creating a more homogeneous circumferential pressure distribution, which delays stall inception to lower flow rates. The results of the porous throat diffuser configuration are compared to a standard vaned diffuser compressor stage in terms of overall compressor performance parameters, circumferential pressure nonuniformity at various locations through the compressor stage and diffuser subcomponent analysis. The diffuser inlet region was found to be the element most influenced by the porous throat diffuser, and the stability limit is mainly governed by this element.

Assessment of a Novel Non-Axial Counter-Rotating Compressor Concept for Aero-Engines

2018 ◽  
Author(s):  
Quentin Dejour ◽  
Huu Duc Vo
Keyword(s):  
Pressure Rise ◽  
Axial Direction ◽  
Boundary Layer Separation ◽  
Low Flow ◽  
Compressor Stage ◽  
Mixed Flow ◽  
Stall Margin ◽  
High Loss ◽  
Multi Stage ◽  
Flow Compressor

This paper presents the first assessment of a new non-axial counter-rotating compressor concept. This concept consists of replacing the stator of a mixed-flow compressor stage or the diffuser of a centrifugal compressor stage with a counter-rotating rotor that will turn the flow back to the axial direction with much lower diffusion factor, while providing the equivalent in work of the upstream mixed-flow rotor or impeller. This concept has two advantages. First, the very high stage pressure rise means that only a single counter-rotating rotor may be required, making mechanical implementation simpler than for multi-stage axial counter-rotating compressors. Second, the replacement of the high flow turning (high loss) stator/diffuser in a non-axial stage with a low flow turning counter-rotating rotor gives the new concept potential for achieving higher efficiency than conventional non-axial compressors. As a first proof of concept, a subsonic counter-rotating mixed-flow compressor and its conventional (i.e. rotor-stator) equivalent have been designed with the intent of being implemented in a test rig. CFD simulations have been carried out for a comparative evaluation of both configurations. Results show that the counter-rotating mixed-flow compressor produces more than double the pressure rise of its conventional version with a slightly higher peak-efficiency while having a smaller axial length. Moreover, the counter-rotating configuration has a better stall margin than its conventional counterpart, for which the boundary layer separation from excessive flow turning in the stator causes early stall.

Sign in / Sign up

Export Citation Format

Share Document