scholarly journals Ephemeral hypoxia reduces oxygen consumption in the Caribbean coral Orbicella faveolata

Coral Reefs ◽  
2021 ◽  
Author(s):  
Philip M. Gravinese ◽  
Alex Douwes ◽  
Katherine R. Eaton ◽  
Erinn M. Muller
Keyword(s):  
Oxygen Consumption ◽  
Elevated Temperature ◽  
Coastal Waters ◽  
Elevated Temperatures ◽  
Wet Season ◽  
Negative Effects ◽  
Hypoxic Conditions ◽  
Orbicella Faveolata ◽  
The Caribbean ◽  
Solubility Of Oxygen

AbstractOxygen concentrations in coastal waters have declined globally by 10% since the mid-twentieth century, and ocean warming will further reduce the solubility of oxygen in coastal habitats. Some nearshore reefs experience periodic hypoxic conditions due to eutrophication, especially during the wet season. Here, we determined the combined impacts of hypoxia and elevated temperature on the reef-building coral, Orbicella faveolata, by exposing corals to normoxic or hypoxic conditions and ambient or elevated temperatures. Oxygen consumption was monitored using closed-system respirometry. Corals within hypoxic conditions consumed 34% less oxygen relative to corals in normoxic conditions. Corals in the elevated temperature normoxic treatment experienced a 10% increase in oxygen consumption relative to the control. Corals exposed to both stressors simultaneously experienced a 62% reduction in oxygen consumption. These results suggest that increased temperature may exacerbate the negative effects of hypoxia on O. faveolata.

On the use of Ozawa/Flynn/Wall method to determine aging activation energy for elastomers

2021 ◽  
pp. 009524432110203
Author(s):  
Sudhir Bafna
Keyword(s):  
Mechanical Properties ◽  
Activation Energy ◽  
Weight Loss ◽  
Oxygen Consumption ◽  
Dwell Time ◽  
Room Temperature ◽  
Elevated Temperatures ◽  
Degradation Mechanism ◽  
Kinetics Of ◽  
Wall Method

It is often necessary to assess the effect of aging at room temperature over years/decades for hardware containing elastomeric components such as oring seals or shock isolators. In order to determine this effect, accelerated oven aging at elevated temperatures is pursued. When doing so, it is vital that the degradation mechanism still be representative of that prevalent at room temperature. This places an upper limit on the elevated oven temperature, which in turn, increases the dwell time in the oven. As a result, the oven dwell time can run into months, if not years, something that is not realistically feasible due to resource/schedule constraints in industry. Measuring activation energy (Ea) of elastomer aging by test methods such as tensile strength or elongation, compression set, modulus, oxygen consumption, etc. is expensive and time consuming. Use of kinetics of weight loss by ThermoGravimetric Analysis (TGA) using the Ozawa/Flynn/Wall method per ASTM E1641 is an attractive option (especially due to the availability of commercial instrumentation with software to make the required measurements and calculations) and is widely used. There is no fundamental scientific reason why the kinetics of weight loss at elevated temperatures should correlate to the kinetics of loss of mechanical properties over years/decades at room temperature. Ea obtained by high temperature weight loss is almost always significantly higher than that obtained by measurements of mechanical properties or oxygen consumption over extended periods at much lower temperatures. In this paper, data on five different elastomer types (butyl, nitrile, EPDM, polychloroprene and fluorocarbon) are presented to prove that point. Thus, use of Ea determined by weight loss by TGA tends to give unrealistically high values, which in turn, will lead to incorrectly high predictions of storage life at room temperature.

scholarly journals Effect of Elevated Temperature on Mechanical Properties of High-Volume Fly Ash-Based Geopolymer Concrete, Mortar and Paste Cured at Room Temperature

Polymers ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1473
Author(s):  
Jun Zhao ◽  
Kang Wang ◽  
Shuaibin Wang ◽  
Zike Wang ◽  
Zhaohui Yang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Elevated Temperature ◽  
Fly Ash ◽  
Residual Strength ◽  
Elevated Temperatures ◽  
High Volume ◽  
Sem Analysis ◽  
Geopolymer Concrete ◽  
Ordinary Concrete ◽  
Exposure Temperature

This paper presents results from experimental work on mechanical properties of geopolymer concrete, mortar and paste prepared using fly ash and blended slag. Compressive strength, splitting tensile strength and flexural strength tests were conducted on large sets of geopolymer and ordinary concrete, mortar and paste after exposure to elevated temperatures. From Thermogravimetric analyzer (TGA), X-ray diffraction (XRD), Scanning electron microscope (SEM) test results, the geopolymer exhibits excellent resistance to elevated temperature. Compressive strengths of C30, C40 and C50 geopolymer concrete, mortar and paste show incremental improvement then followed by a gradual reduction, and finally reach a relatively consistent value with an increase in exposure temperature. The higher slag content in the geopolymer reduces residual strength and the lower exposure temperature corresponding to peak residual strength. Resistance to elevated temperature of C40 geopolymer concrete, mortar and paste is better than that of ordinary concrete, mortar and paste at the same grade. XRD, TGA and SEM analysis suggests that the heat resistance of C–S–H produced using slag is lower than that of sulphoaluminate gel (quartz and mullite, etc.) produced using fly ash. This facilitates degradation of C30, C40 and C50 geopolymer after exposure to elevated temperatures.

Oxygen consumption and blood gases ofOctopus vulgaris in hypoxic conditions

1982 ◽  
Vol 148 (1) ◽  
pp. 35-40 ◽  
Author(s):  
D. F. Houlihan ◽  
A. J. Innes ◽  
M. J. Wells ◽  
J. Wells
Keyword(s):  
Oxygen Consumption ◽  
Blood Gases ◽  
Hypoxic Conditions

Effects of Elevated Temperatures on the Compressive Strength of HFCC

2011 ◽  
Vol 261-263 ◽  
pp. 416-420 ◽  
Author(s):  
Fu Ping Jia ◽  
Heng Lin Lv ◽  
Yi Bing Sun ◽  
Bu Yu Cao ◽  
Shi Ning Ding
Keyword(s):  
Compressive Strength ◽  
Elevated Temperature ◽  
Fly Ash ◽  
Room Temperature ◽  
Elevated Temperatures ◽  
Relative Strength ◽  
Ordinary Concrete ◽  
Residual Compressive Strength ◽  
Fly Ash Concrete ◽  
The Relationship

This paper presents the results of elevated temperatures on the compressive of high fly ash content concrete (HFCC). The specimens were prepared with three different replacements of cement by fly ash 30%, 40% and 50% by mass and the residual compressive strength was tested after exposure to elevated temperature 250, 450, 550 and 650°C and room temperature respectively. The results showed that the compressive strength apparently decreased with the elevated temperature increased. The presence of fly ash was effective for improvement of the relative strength, which was the ratio of residual compressive strength after exposure to elevated temperature and ordinary concrete. The relative compressive strength of fly ash concrete was higher than those of ordinary concrete. Based on the experiments results, the alternating simulation formula to determine the relationship among relative strength, elevated temperature and fly ash replacement is developed by using regression of results, which provides the theoretical basis for the evaluation and repair of HFCC after elevated temperature.

Microstructure Evolution and Mechanical Properties of an Al-Cu-Mg Alloy at Elevated Temperature

2014 ◽  
Vol 1004-1005 ◽  
pp. 148-153
Author(s):  
Min Hao ◽  
Ji Gang Ru ◽  
Ming Liu ◽  
Kun Zhang ◽  
Liang Wang ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Elevated Temperature ◽  
Elevated Temperatures ◽  
Shear Fracture ◽  
S Phase ◽  
Mg Alloy ◽  
Transmission Electron ◽  
Fracture Features ◽  
Scanning Electron

Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were utilized to study the microstructure and mechanical behavior of an Al-Cu-Mg alloy after tensile test at 125°C, 150°C, 175°C and 200 °C, respectively. The yield strength and ultimate tensile strength decreased with the increase of temperature, while the elongation increased firstly and then decreased. The S and S′ precipitate after tension at elevated temperatures. When the temperature was higher than 175°C, the precipitate coarsens rapidly. The alloys displayed a shear fracture features at elevated temperature. The larger S′ and S phase coarsened and dropped which forming crack in the grain boundaries and precipitate interfaces, resulting in the decrease of the elongation of the alloy.

Study on the Formability of Aluminium Alloy Sheets at Room and Elevated Temperatures

2016 ◽  
Vol 877 ◽  
pp. 393-399
Author(s):  
Jia Zhou ◽  
Jun Ping Zhang ◽  
Ming Tu Ma
Keyword(s):  
Mechanical Properties ◽  
Aluminum Alloy ◽  
Elevated Temperature ◽  
Aluminium Alloy ◽  
Aluminium Alloys ◽  
Elevated Temperatures ◽  
Hot Stamping ◽  
Natural Aging ◽  
Alloy Sheet ◽  
Aluminum Alloy Sheet

This paper presents the main achievements of a research project aimed at investigating the applicability of the hot stamping technology to non heat treatable aluminium alloys of the 5052 H32 and heat treatable aluminium alloys of the 6016 T4P after six months natural aging. The formability and mechanical properties of 5052 H32 and 6016 T4P aluminum alloy sheets after six months natural aging under different temperature conditions were studied, the processing characteristics and potential of the two aluminium alloy at room and elevated temperature were investigated. The results indicated that the 6016 aluminum alloy sheet exhibit better mechanical properties at room temperature. 5052 H32 aluminum alloy sheet shows better formability at elevated temperature, and it has higher potential to increase formability by raising the temperature.

Experimental Investigation of Ti-6Al-4V with a Biaxial Tensile Test Setup at Elevated Temperature

2014 ◽  
Vol 622-623 ◽  
pp. 273-278 ◽  
Author(s):  
Marion Merklein ◽  
Sebastian Suttner ◽  
Adam Schaub
Keyword(s):  
Elevated Temperature ◽  
Elevated Temperatures ◽  
Tensile Tests ◽  
Advanced Materials ◽  
Uniaxial Tensile ◽  
Plastic Yielding ◽  
Characterization Methods ◽  
Specific Strength ◽  
Biaxial Tensile ◽  
Stress States

The requirement for products to reduce weight while maintaining strength is a major challenge to the development of new advanced materials. Especially in the field of human medicine or aviation and aeronautics new materials are needed to satisfy increasing demands. Therefore the titanium alloy Ti-6Al-4V with its high specific strength and an outstanding corrosion resistance is used for high and reliable performance in sheet metal forming processes as well as in medical applications. Due to a meaningful and accurate numerical process design and to improve the prediction accuracy of the numerical model, advanced material characterization methods are required. To expand the formability and to skillfully use the advantage of Ti-6Al-4V, forming processes are performed at elevated temperatures. Thus the investigation of plastic yielding at different stress states and at an elevated temperature of 400°C is presented in this paper. For this reason biaxial tensile tests with a cruciform shaped specimen are realized at 400°C in addition to uniaxial tensile tests. Moreover the beginning of plastic yielding is analyzed in the first quadrant of the stress space with regard to complex material modeling.

Polycrystal Simulations Investigating the Effect of Additional Slip System Availability in a 6063 Aluminum Alloy at Elevated Temperature

2008 ◽  
Vol 130 (2) ◽  
Author(s):  
Antoinette M. Maniatty ◽  
David J. Littlewood ◽  
Jing Lu
Keyword(s):  
Aluminum Alloy ◽  
Elevated Temperature ◽  
Compression Test ◽  
Elevated Temperatures ◽  
Material Model ◽  
Grain Structure ◽  
Slip Systems ◽  
Modeling Framework ◽  
Element Analysis ◽  
6063 Aluminum Alloy

In order to better understand and predict the intragrain heterogeneous deformation in a 6063 aluminum alloy deformed at an elevated temperature, when additional slip systems beyond the usual octahedral slip systems are active, a modeling framework for analyzing representative polycrystals under these conditions is presented. A model polycrystal that has a similar microstructure to that observed in the material under consideration is modeled with a finite element analysis. A large number of elements per grain (more than 1000) are used to capture well the intragranular heterogeneous response. The polycrystal model is analyzed with three different sets of initial orientations. A compression test is used to calibrate the material model, and a macroscale simulation of the compression test is used to define the deformation history applied to the model polycrystal. In order to reduce boundary condition effects, periodic boundary conditions are applied to the model polycrystal. To investigate the effect of additional slip systems expected to be active at elevated temperatures, the results considering only the 12 {111}⟨110⟩ slip systems are compared to the results with the additional 12 {110}⟨110⟩ and {001}⟨110⟩ slip systems available (i.e., 24 available slip systems). The resulting predicted grain structure and texture are compared to the experimentally observed grain structure and texture in the 6063 aluminum alloy compression sample as well as to the available data in the literature, and the intragranular misorientations are studied.

Structural Performance of Pultruded Composites under Elevated Temperatures

2009 ◽  
Vol 79-82 ◽  
pp. 2223-2226
Author(s):  
Ayman S. Mosallam
Keyword(s):  
Elevated Temperature ◽  
High Temperatures ◽  
Elevated Temperatures ◽  
Oxidative Degradation ◽  
Viscoelastic Behavior ◽  
Structural Performance ◽  
Crystalline Polymers ◽  
Damage To The Material ◽  
Continuous Working ◽  
Pultruded Composites

One of the major limitations for wider use of pultruded fiber reinforced polymeric (PFRP) composites in the civil engineering sector has been their behavior under elevated temperature and ultimately fire. This limitation arises not only due to the reduction in mechanical properties at high temperatures, including increased propensity to creep, but also due to limitations on the continuous working temperature causing permanent damage to the material as a result of thermal and oxidative degradation. Significant gains in property retention at high temperatures with crystalline polymers have been derived from the incorporation of fibrous reinforcement, but the development of new polymer matrices is the key for further elevation of the useful temperature range. This paper presents summary results of a research project focused on characterizing the viscoelastic behavior of commercially-produced, off-the-shelf unidirectional PFRP materials subjected to elevated temperature environments.

scholarly journals R-BPMV-Mediated Resistance to Bean pod mottle virus in Phaseolus vulgaris L. Is Heat-Stable but Elevated Temperatures Boost Viral Infection in Susceptible Genotypes

Viruses ◽  
2021 ◽  
Vol 13 (7) ◽  
pp. 1239
Author(s):  
Chouaïb Meziadi ◽  
Julie Lintz ◽  
Masoud Naderpour ◽  
Charlotte Gautier ◽  
Sophie Blanchet ◽  
...  
Keyword(s):  
Elevated Temperature ◽  
Phaseolus Vulgaris ◽  
Elevated Temperatures ◽  
Heat Waves ◽  
Dominant Gene ◽  
Atmospheric Temperature ◽  
Mottle Virus ◽  
Bean Pod Mottle Virus ◽  
Heat Stable ◽  
The Impact

In the context of climate change, elevated temperature is a major concern due to the impact on plant–pathogen interactions. Although atmospheric temperature is predicted to increase in the next century, heat waves during summer seasons have already become a current problem. Elevated temperatures strongly influence plant–virus interactions, the most drastic effect being a breakdown of plant viral resistance conferred by some major resistance genes. In this work, we focused on the R-BPMV gene, a major resistance gene against Bean pod mottle virus in Phaseolus vulgaris. We inoculated different BPMV constructs in order to study the behavior of the R-BPMV-mediated resistance at normal (20 °C) and elevated temperatures (constant 25, 30, and 35 °C). Our results show that R-BPMV mediates a temperature-dependent phenotype of resistance from hypersensitive reaction at 20 °C to chlorotic lesions at 35 °C in the resistant genotype BAT93. BPMV is detected in inoculated leaves but not in systemic ones, suggesting that the resistance remains heat-stable up to 35 °C. R-BPMV segregates as an incompletely dominant gene in an F2 population. We also investigated the impact of elevated temperature on BPMV infection in susceptible genotypes, and our results reveal that elevated temperatures boost BPMV infection both locally and systemically in susceptible genotypes.

Sign in / Sign up

Export Citation Format

Share Document