scholarly journals Sessile Drop in Microgravity: Creation, Contact Angle and Interface

2009 ◽  
Vol 21 (S1) ◽  
pp. 67-76 ◽  
Author(s):  
David Brutin ◽  
ZhiQuiang Zhu ◽  
Ouamar Rahli ◽  
JingChang Xie ◽  
QuiSheng Liu ◽  
...  
Keyword(s):  
Contact Angle ◽  
Sessile Drop

Comparative studies of nitrogen plasma and argon plasma treatment on the strength of PBO fibre reinforced high-temperature resistant thermoplastic composite

2021 ◽  
pp. 095400832098729
Author(s):  
K Sudheendra ◽  
Jennifer Vinodhini ◽  
M Govindaraju ◽  
Shantanu Bhowmik
Keyword(s):  
Contact Angle ◽  
High Temperature ◽  
Plasma Treatment ◽  
Sessile Drop ◽  
Dynamic Contact Angle ◽  
Argon Plasma ◽  
Film Surface ◽  
Fibre Surface ◽  
Nitrogen Plasma ◽  
Thermoplastic Composite

The study involves the processing of a novel poly [1, 4-phenylene-cis-benzobisoxazole] (PBO) fibre reinforced high-temperature thermoplastic composite with polyaryletherketone (PAEK) as the matrix. The PBO fibre and the PAEK film surface was modified using the method of argon and nitrogen plasma treatment. The investigation primarily focuses on evaluating the tensile properties of the fabricated laminates and correlating it with the effect of plasma treatment, surface characteristics, and its fracture surface. A 5% decrease in tensile strength was observed post argon plasma treatment while a 27% increase in strength was observed post nitrogen plasma treatment. The morphology of the failure surface was investigated by scanning electron microscopy and an interfacial failure was observed. Furthermore, the effect of plasma on the wettability of PBO fibres and PAEK film surface was confirmed by the Dynamic Contact Angle analysis and sessile drop method respectively. FTIR spectral analysis was done to investigate the effect of plasma treatment on the chemical structure on the surface. The results of the wettability study showed that the argon plasma treatment of the fibre surface increased its hydrophobicity while nitrogen plasma treatment resulted in the reduction of contact angle.

scholarly journals Interfacial Behaviour in Ferroalloys: The Influence of Sulfur in FeMn and SiMn Systems

2021 ◽  
Author(s):  
Sergey Bublik ◽  
Sarina Bao ◽  
Merete Tangstad ◽  
Kristian Etienne Einarsrud
Keyword(s):  
Contact Angle ◽  
Interfacial Tension ◽  
Sessile Drop ◽  
Interfacial Properties ◽  
Apparent Contact Angle ◽  
Holding Time ◽  
Transfer Rates ◽  
Experimental Parameters ◽  
Interfacial Behaviour ◽  
Modelling Approach

AbstractThe present study has investigated the influence of sulfur content in synthetic FeMn and SiMn from 0 to 1.00 wt pct on interfacial properties between these ferroalloys and slags. The effect of experimental parameters such as temperature and holding time was evaluated. Interfacial interaction between ferroalloys and slags was characterized by interfacial tension and apparent contact angle between metal and slag, measured based on the Young–Laplace equation and an inverse modelling approach developed in OpenFOAM. The results show that sulfur has a significant influence on both interfacial tension and apparent contact angle, decreasing both values and promoting the formation of a metal-slag mixture. Despite the fact that sulfur was added only to the ferroalloys, most of sulfur is distributed into slag after reactions with the metal phase. Increasing the maximum experimental temperature in the sessile drop furnace also resulted in a decrease of both interfacial properties, resulting in higher mass transfer rates and intensive reactions between metal and slag. The effect of holding time demonstrated that after reaching equilibrium in FeMn-slag and SiMn-slag systems (both with and without sulfur), interfacial tension and apparent contact angle remain constant.

scholarly journals Carbon dioxide adsorption and interaction with formation fluids of Jordanian unconventional reservoirs

2021 ◽  
Author(s):  
H. Samara ◽  
T. V. Ostrowski ◽  
F. Ayad Abdulkareem ◽  
E. Padmanabhan ◽  
P. Jaeger
Keyword(s):  
Carbon Dioxide ◽  
Contact Angle ◽  
Interfacial Tension ◽  
Oil Recovery ◽  
Gas Adsorption ◽  
Sessile Drop ◽  
Global Climate ◽  
Gravimetric Method ◽  
Rock Surface ◽  
Operating Pressure

AbstractShales are mostly unexploited energy resources. However, the extraction and production of their hydrocarbons require innovative methods. Applications involving carbon dioxide in shales could combine its potential use in oil recovery with its storage in view of its impact on global climate. The success of these approaches highly depends on various mechanisms taking place in the rock pores simultaneously. In this work, properties governing these mechanisms are presented at technically relevant conditions. The pendant and sessile drop methods are utilized to measure interfacial tension and wettability, respectively. The gravimetric method is used to quantify CO2 adsorption capacity of shale and gas adsorption kinetics is evaluated to determine diffusion coefficients. It is found that interfacial properties are strongly affected by the operating pressure. The oil-CO2 interfacial tension shows a decrease from approx. 21 mN/m at 0.1 MPa to around 3 mN/m at 20 MPa. A similar trend is observed in brine-CO2 systems. The diffusion coefficient is observed to slightly increase with pressure at supercritical conditions. Finally, the contact angle is found to be directly related to the gas adsorption at the rock surface: Up to 3.8 wt% of CO2 is adsorbed on the shale surface at 20 MPa and 60 °C where a maximum in contact angle is also found. To the best of the author’s knowledge, the affinity of calcite-rich surfaces toward CO2 adsorption is linked experimentally to the wetting behavior for the first time. The results are discussed in terms of CO2 storage scenarios occurring optimally at 20 MPa.

scholarly journals THE CONTACT ANGLE CONTROL OF THE SOLDER FOR IMPROVING THE SOLDERING QUALITY

2021 ◽  
pp. 161-166
Author(s):  
Чуйко М.М. ◽  
Завальський В.
Keyword(s):  
Contact Angle ◽  
Sessile Drop ◽  
Electrical Contact ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Soldering Process ◽  
Basic Parameters ◽  
The Right

High quality of the soldering process can be achieved with the right choice of the necessary soldering materials. Since wetting determines the further nature of the connection between the solder and the main soldering material, the contact angle  measurement  is the basis for quality control of soldering materials, provided that the basic requirements of the technological process. The determination of the contact angle value is carried out by the indirect method of the sessile drop, by measuring the basic parameters of the drop using infrared transducer. A smaller value of the contact angle corresponds to a better interaction of materials, and hence a better electrical contact

scholarly journals THE METHOD OF PREPARING SOIL SAMPLES FOR SOIL – WATER CONTACT ANGLE MEASUREMENT USING SESSILE-DROP TECHNIQUE

2019 ◽  
pp. 91-112
Author(s):  
N. V. Matveeva ◽  
E. Yu. Milanovsky ◽  
O. B. Rogova
Keyword(s):  
Contact Angle ◽  
Sample Preparation ◽  
Sessile Drop ◽  
Solid Phase ◽  
Chestnut Soil ◽  
Soil Samples ◽  
Adhesive Tape ◽  
Membrane Filters ◽  
Advantages And Disadvantages ◽  
Significant Difference

The method of soil samples preparation for measuring the (wetting) contact angle (CA) of the soil solid phase surface using membrane filters is proposed. The samples of kaolinite, a standard sample of chernozem and samples of agro-chestnut soil were taken for the experiment. The results of the CA measurements using two types of sample preparation for the analysis were compared. The first method of sample preparation was to apply a sample to a double-sided adhesive tape; the second method involved the deposition of suspensions of the studied samples of certain concentrations on membrane filters. The advantages and disadvantages of each sample preparation method are described. The significant difference in the obtained CA values depending on the sample preparation for measurement was revealed. The method of sample preparation with the use of membrane filters developed by the authors made it possible to reduce the CA measurement error by more than 2 times. Reducing the variation of the CA value of a single sample will allow comparing similar soil samples, including soils of the same type, but involved in different land use systems.

Comparative Study of Surface Energies of Native Oxides of Si(100) and Si(111) via Three Liquid Contact Angle Analysis

MRS Advances ◽  
2018 ◽  
Vol 3 (57-58) ◽  
pp. 3379-3390 ◽  
Author(s):  
Saaketh R. Narayan ◽  
Jack M. Day ◽  
Harshini L. Thinakaran ◽  
Nicole Herbots ◽  
Michelle E. Bertram ◽  
...  
Keyword(s):  
Contact Angle ◽  
Surface Energy ◽  
Sessile Drop ◽  
Surface Composition ◽  
Ion Beam ◽  
Contact Angles ◽  
Van Der Waals Interactions ◽  
Native Oxides ◽  
Relative Errors ◽  
Contact Angle Analysis

ABSTRACTThe effects of crystal orientation and doping on the surface energy, γT, of native oxides of Si(100) and Si(111) are measured via Three Liquid Contact Angle Analysis (3LCAA) to extract γT, while Ion Beam Analysis (IBA) is used to detect Oxygen. During 3LCAA, contact angles for three liquids are measured with photographs via the “Drop and Reflection Operative Program (DROP™). DROP™ removes subjectivity in image analysis, and yields reproducible contact angles within < ±1°. Unlike to the Sessile Drop Method, DROP can yield relative errors < 3% on sets of 20-30 drops. Native oxides on 5 x 1013 B/cm3 p- doped Si(100) wafers, as received in sealed, 25 wafer teflon boats continuously stored in Class 100/ISO 5 conditions at 24.5°C in 25% controlled humidity, are found to be hydrophilic. Their γT, 52.5 ± 1.5 mJ/m2, is reproducible between four boats from three sources, and 9% greater than γT of native oxides on n- doped Si(111), which averages 48.1 ± 1.6 mJ/m2 on four 4” Si(111) wafers. IBA combining 16O nuclear resonance with channeling detects 30% more oxygen on native oxides of Si(111) than Si(100). While γT should increase on thinner, more defective oxides, Lifshitz-Van der Waals interactions γLW on native oxides of Si(100) remain at 36 ± 0.4 mJ/m2, equal to γLW on Si(111), 36 ± 0.6 mJ/m2, since γLW arises from the same SiO2 molecules. Native oxides on 4.5 x 1018 B/cm3 p+ doped Si(100) yield a γT of 39 ± 1 mJ/m2, as they are thicker per IBA. In summary, 3LCAA and IBA can detect reproducibly and accurately, within a few %, changes in the surface energy of native oxides due to thickness and surface composition arising from doping or crystal structure, if conducted in well controlled clean room conditions for measurements and storage.

A Method for Measuring Contact Angle and the Influence of Surface-Fluid Parameters on the Boiling Heat Transfer Performance

2020 ◽  
Vol 142 (9) ◽  
Author(s):  
Alex P. da Cunha ◽  
Taye S. Mogaji ◽  
Reinaldo R. de Souza ◽  
Elaine M. Cardoso
Keyword(s):  
Heat Transfer ◽  
Surface Roughness ◽  
Contact Angle ◽  
Heat Transfer Performance ◽  
Sessile Drop ◽  
Pool Boiling ◽  
Transfer Performance ◽  
Transfer Coefficients ◽  
Experimental Apparatus ◽  
Boiling Process

Abstract An experimental apparatus and a computational routine were developed and implemented in order to obtain the sessile drop images and the contact angle measurement for different fluids and surface conditions. Moreover, experimental results of heat transfer coefficients (HTCs) during pool boiling of de-ionized water (DI water), Al2O3-DI water- and Fe2O3-DI water-based nanofluids are presented in this paper. Based on these results, the effect of surface roughness and nanofluid concentration on the surface wettability, contact angle, and the heat transfer coefficient was analyzed. The experiments were performed on copper heating surfaces with different roughness values (corresponding to a smooth surface or a rough surface). The coated surfaces were produced by the nanofluid pool boiling process at two different volumetric concentrations. All surfaces were subjected to metallographic, wettability and roughness tests. For smooth surfaces, in comparison to DI water, heat transfer enhancement up to 60% is observed for both nanofluids at low concentrations. As the concentration of the nanofluid increases, the surface roughness increases and the contact angle decreases, characterizing a hydrophilic behavior. The analyses indicate that the boiling process of nanofluid leads to the deposition of a coating layer on the surface, which influences the heat transfer performance in two-phase systems.

Sign in / Sign up

Export Citation Format

Share Document