Preparation of aqueous dispersion of thermoplastic sizing agent for carbon fiber by emulsion/solvent evaporation

TiO2/carbon fiber composite is achieved by loading TiO2 nanoparticles on biomass carbon fiber, which originates from the carbonized natural bast. The carbonized process and the loading amount of TiO2 are researched in detail. It is found that the carbonized bast fiber shows robust adsorption characteristics for TiO2 nanoparticles in aqueous dispersion, and TiO2 nanoparticles with ~15 wt.% in total weight are uniformly loaded onto the fiber surface. The photocatalytic properties of TiO2/carbon fiber composite are evaluated by photocatalytic degradation of rhodamine B and water splitting for hydrogen production. The results indicate that 90% RhB molecules could be attacked in 60 min under UV light irradiation, and the hydrogen production rate of water splitting is up to 338.51 μmol/h. The highlight is that TiO2/carbon fiber composite is easy to be recycled due to the incorporation of macroscopical biomass carbon fiber.

Download Full-text

Morphological transformations in solution-cast Styrene-Butadiene-Styrene (SBS) triblock copolymer thin films

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s042482010013729x ◽

1995 ◽

Vol 53 ◽

pp. 184-185

Author(s):

Ginam Kim ◽

W. Marsillo ◽

M. Libera

Keyword(s):

Thin Films ◽

Triblock Copolymer ◽

Annealing Treatment ◽

Minor Component ◽

Solvent Evaporation ◽

Single Crystal Substrate ◽

Transparent Films ◽

Crystal Substrate ◽

Solution Cast ◽

Morphological Transformations

The fact that block copolymers can assume a range of morphologies depending upon such variables as relative block length and molecular weight is now well known. In the case of poly(styrene)[PS]-poly(butadiene)[PB]-poly(styrene) (SBS) triblock copolymer, the morphologies range from spheres (roughly ~20% minor component), to cylinders (roughly 20%~35% minor component), to lamellae (roughly equal component fractions) Most recently, there has been increasing interest in transformations between morphologies by thermal annealing. This paper describes initial results studying the effect of solvent evaporation rate and post-casting annealing treatment on the morphology of SBS thin films.TEM specimens were prepared by solution casting electron transparent films. 50 μl of 0.1 wt% SBS (30% styrene, Mw=14,000, Scientific Polymer Products, Inc.) dissolved in toluene was deposited on a polished NaCl single crystal substrate placed in a small dish. After solvent evaporation the film was cut into small squares, floated from the salt in water, and each square was collected on a Cu grid.

Download Full-text

Effects of high pressure on the crystallization of carbon fiber reinforced polyetheretherketone (CF/PEEK) laminate composites

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100177519 ◽

1990 ◽

Vol 48 (4) ◽

pp. 876-877

Author(s):

Hong-Ming Lin ◽

C. H. Liu ◽

R. F. Lee

Keyword(s):

High Pressure ◽

Carbon Fiber ◽

Sample Surface ◽

High Yield ◽

Fiber Reinforced ◽

Laminate Composites ◽

Peek Composite ◽

Continuous Carbon Fiber ◽

Carbon Fiber Reinforced

Polyetheretherketone (PEEK) is a crystallizable thermoplastic used as composite matrix materials in application which requires high yield stress, high toughness, long term high temperature service, and resistance to solvent and radiation. There have been several reports on the crystallization behavior of neat PEEK and of CF/PEEK composite. Other reports discussed the effects of crystallization on the mechanical properties of PEEK and CF/PEEK composites. However, these reports were all concerned with the crystallization or melting processes at or close to atmospheric pressure. Thus, the effects of high pressure on the crystallization of CF/PEEK will be examined in this study.The continuous carbon fiber reinforced PEEK (CF/PEEK) laminate composite with 68 wt.% of fibers was obtained from Imperial Chemical Industry (ICI). For the high pressure experiments, HIP was used to keep these samples under 1000, 1500 or 2000 atm. Then the samples were slowly cooled from 420 °C to 60 °C in the cooling rate about 1 - 2 degree per minute to induce high pressure crystallization. After the high pressure treatment, the samples were scanned in regular DSC to study the crystallinity and the melting temperature. Following the regular polishing, etching, and gold coating of the sample surface, the scanning electron microscope (SEM) was used to image the microstructure of the crystals. Also the samples about 25mmx5mmx3mm were prepared for the 3-point bending tests.

Download Full-text

Enhanced performance of supercapacitors by constructing a “mini parallel-plate capacitor” in an electrode with high dielectric constant materials

Journal of Materials Chemistry A ◽

10.1039/d0ta04364h ◽

2020 ◽

Vol 8 (32) ◽

pp. 16661-16668

Author(s):

Huayao Tu ◽

Shouzhi Wang ◽

Hehe Jiang ◽

Zhenyan Liang ◽

Dong Shi ◽

...

Keyword(s):

Dielectric Constant ◽

Carbon Fiber ◽

Parallel Plate ◽

Sandwich Structure ◽

High Dielectric Constant ◽

Parallel Plate Capacitor ◽

Plate Capacitor ◽

Fiber Metal ◽

High Dielectric ◽

Mini Plate

The carbon fiber/metal oxide/metal oxynitride layer sandwich structure is constructed in the electrode to form a mini-plate capacitor. High dielectric constant metal oxides act as dielectric to increase their capacitance.

Download Full-text