scholarly journals The Correlation between Ion Beam/Material Interactions and Practical FIB Specimen Preparation

2003 ◽  
Vol 9 (3) ◽  
pp. 216-236 ◽  
Author(s):  
B.I. Prenitzer ◽  
C.A. Urbanik-Shannon ◽  
L.A. Giannuzzi ◽  
S.R. Brown ◽  
R.B. Irwin ◽  
...  
Keyword(s):  
Monte Carlo Simulation ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Target Material ◽  
Beam Current ◽  
Milling Process ◽  
Specimen Preparation ◽  
Analytical Instrument ◽  
Simulation Code ◽  
Raster Pattern

The focused ion beam (FIB) tool has been successfully used as both a stand alone analytical instrument and a means to prepare specimens for subsequent analysis by SEM, TEM, SIMS, XPS, and AUGER. In this work, special emphasis is given to TEM specimen preparation by the FIB lift-out technique. The fundamental ion/solid interactions that govern the FIB milling process are examined and discussed with respect to the preparation of electron transparent membranes. TRIM, a Monte Carlo simulation code, is used to physically model variables that influence FIB sputtering behavior. The results of such computer generated models are compared with empirical observations in a number of materials processed with an FEI 611 FIB workstation. The roles of incident ion attack angle, beam current, trench geometry, raster pattern, and target-material-dependent removal rates are considered. These interrelationships are used to explain observed phenomena and predict expected milling behaviors, thus increasing the potential for the FIB to be used more efficiently with reproducible results.

Characterization of FIB Damage in Silicon

1999 ◽  
Vol 5 (S2) ◽  
pp. 740-741 ◽  
Author(s):  
C.A. Urbanik ◽  
B.I. Prenitzer ◽  
L.A. Gianhuzzi ◽  
S.R. Brown ◽  
T.L. Shofner ◽  
...  
Keyword(s):  
Focused Ion Beam ◽  
Ion Beam ◽  
Target Material ◽  
Beam Current ◽  
Specimen Preparation ◽  
Transfer Energy ◽  
Transmission Electron ◽  
Preparation Techniques ◽  
Reactive Gas

Focused ion beam (FIB) instruments are useful for high spatial resolution milling, deposition, and imaging capabilities. As a result, FIB specimen preparation techniques have been widely accepted within the semiconductor community as a means to rapidly prepare high quality, site-specific specimens for transmission electron microscopy (TEM) [1]. In spite of the excellent results that have been observed for both high resolution (HREM) and standard TEM specimen preparation applications, a degree of structural modification is inherent to FIB milled surfaces [2,3]. The magnitude of the damage region that results from Ga+ ion bombardment is dependent on the operating parameters of the FIB (e.g., beam current, beam voltage, milling time, and the use of reactive gas assisted etching).Lattice defects occur as a consequence of FIB milling because the incident ions transfer energy to the atoms of the target material. Momentum transferred from the incident ions to the target atoms can result in the creation of point defects (e.g., vacancies, self interstitials, and interstitial and substitutional ion implantation), the generation of phonons, and plasmon excitation in the case of metal targets.

Material Dependence of Sputtering Behavior During Focused Ion Beam Milling: A Correlation Between Monte Carlo Based Simulation and Empirical Observation

1998 ◽  
Vol 4 (S2) ◽  
pp. 858-859 ◽  
Author(s):  
B.I. Prenitzer ◽  
L.A. Giannuzzi ◽  
S.R. Brown ◽  
R.B. Irwin ◽  
T.L. Shofner ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Monte Carlo ◽  
Critical Incident ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Target Material ◽  
Process Efficiency ◽  
Specimen Preparation ◽  
Simulation Code ◽  
Empirical Observation

The focused ion beam (FIB) lift-out method is a high precision technique by which site-specific cross-section transmission electron microscopy (TEM) specimens may be rapidly prepared from virtually any material. The technique is particularly useful when the sample geometry or composition is complex (e.g., fibers, powders, composites and interfaces). In addition to the preparation of TEM specimens, FIB milling has also found widespread utility in micromachining and microfabrication applications as well as specimen preparation for scanning electron microscopy (SEM) and secondary ion mass spectrometry (SIMS).As the applications of the FEB instrument continue to become more universally recognized, the need to understand the interrelationships between the target material, processing parameters, and process efficiency of the milling phenomena becomes more critical. Incident ion attack angle, target material stopping efficiency and sputtering yield, Y, are important variables governing the milling process. TRIM, a binary collision approximation Monte Carlo simulation code, is used to physically model variables that influence FIB sputtering behavior.

Optimization Based Geometric Modeling of Nano/Micro Scale Ion Milling of Organic Materials

2009 ◽  
Author(s):  
Jing Fu ◽  
Sanjay B. Joshi
Keyword(s):  
Geometric Modeling ◽  
Focused Ion Beam ◽  
Organic Materials ◽  
Ion Beam ◽  
Target Material ◽  
Milling Process ◽  
Ion Milling ◽  
Flexible Tool ◽  
Water Ice ◽  
Micro Scale

Recently, Focused Ion Beam (FIB) instruments have begun be applied to organic materials such as polymers and biological systems. This provides a novel tool for sectioning biological samples for analysis, or microfabrication with environment friendly materials. The modeling of nano/micro scale geometry accurately sculptured by FIB milling is crucial for generating the milling plan and process control, and for computer simulation for prediction and visualization of the milled geometry. However, modeling of the ion milling process on compound materials, especially for high aspect ratio feature, is still difficult due to the complexity of target material, as well as multiple physical and chemical interactions involved. In this study, a comprehensive model of ion milling with organic targets is presented to address the challenges using a simulation based approach. This platform has also been validated by milling different features on water ice in a cryogenic environment, and the simulation and experiment results show great consistency. With the proliferation of nanotechnology to biomedical and biomaterial domains, the proposed approach is expected to be a flexible tool for various applications involving novel and heterogeneous milling targets.

Optimization of FIB-Milling Technique for Preparation of TEM Specimens from Copper/Low-K Materials

1999 ◽  
Vol 5 (S2) ◽  
pp. 902-903
Author(s):  
F. Shaapur ◽  
D. Brazeau ◽  
B. Foran
Keyword(s):  
Structural Damage ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Milling Process ◽  
Ion Source ◽  
Specimen Preparation ◽  
Ion Milling ◽  
Cross Sectional ◽  
Area Of Interest ◽  
Low K

Focused ion beam (FIB) thinning of materials to electron transparency is now a routine procedure for preparation of specimens for transmission electron microscopy (TEM) of microelectronic materials and devices. The nano-scale structural damage, including implantation and amorphization due to this ion milling process has been well investigated and documented. In this paper, we discuss the micro-scale structural damage observed in copper/low-k materials and our efforts to minimize the extent of the damage without compromising the overall specimen preparation time.Figure 1 shows an area-specific cross-sectional specimen prepared from a copper/low-k via-chain test structure using the FIB-milling technique. The procedure involved mechanical thinning of a transverse wafer sliver followed by FIB-milling the area of interest to electron transparency according to conventional steps and conditions' using a liquid Ga+ ion source FIB system. The evidence of structural damage in terms of melting and/or sputtering of the metallization is visible at different areas.

Focused Ion Beam Milling for Site Specific Scanning and Transmission Electron Microscopy Specimen Preparation

1997 ◽  
Vol 3 (S2) ◽  
pp. 347-348
Author(s):  
L.A. Giannuzzi ◽  
J.L. Drownt ◽  
S.R. Brown ◽  
R.B. Irwin ◽  
F.A. Stevie
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Region Of Interest ◽  
Beam Current ◽  
Specimen Preparation ◽  
Site Specific ◽  
Sem Image ◽  
Transmission Electron

It has been shown that a focused ion beam (FIB) instrument may be used to prepare site specific cross-sectioned specimens to within < 0.1 μm for both scanning and transmission electron microscopy (SEM and TEM, respectively). FIB specimen preparation has been used almost exclusively in the microelectronics industry. Recently, FIB specimen preparation has been utilized for other materials systems and applications.A cross-sectioned SEM specimen is produced by sputtering away a trench of material from near the region of interest. Large amounts of material are sputtered using large ion beam diameters (e.g., l00’s nm) and high beam current (e.g., l000’s pA), while the final sputtering operations are achieved using smaller beam diameters (e.g., < 10 nm) and lower beam current (e.g., 10’s of pA). The SEM specimen may then be etched to reveal particular microstructural features of interest. A low magnification SEM image of a multi-layered device prepared for cross-section analysis by the FIB method is shown in FIG. 1.

Low Energy Ar Ion Milling of FIB TEM Specimens from 14 nm and Future FinFET Technologies

2018 ◽  
Author(s):  
C.S. Bonifacio ◽  
P. Nowakowski ◽  
M.J. Campin ◽  
M.L. Ray ◽  
P.E. Fischione
Keyword(s):  
Field Effect Transistor ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Specimen Preparation ◽  
Ion Milling ◽  
Transmission Electron ◽  
High Resolution Tem ◽  
Effect Transistor ◽  
20 Nm ◽  
Argon Ion

Abstract Transmission electron microscopy (TEM) specimens are typically prepared using the focused ion beam (FIB) due to its site specificity, and fast and accurate thinning capabilities. However, TEM and high-resolution TEM (HRTEM) analysis may be limited due to the resulting FIB-induced artifacts. This work identifies FIB artifacts and presents the use of argon ion milling for the removal of FIB-induced damage for reproducible TEM specimen preparation of current and future fin field effect transistor (FinFET) technologies. Subsequently, high-quality and electron-transparent TEM specimens of less than 20 nm are obtained.

Focused Ion Beam Analysis of Low-K Dielectrics

2000 ◽  
Author(s):  
H. J. Bender ◽  
R. A. Donaton
Keyword(s):  
Electron Microscope ◽  
Cross Section ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Single Step ◽  
Specimen Preparation ◽  
Transmission Electron ◽  
Beam Analysis ◽  
Low K ◽  
Scanning Electron

Abstract The characteristics of an organic low-k dielectric during investigation by focused ion beam (FIB) are discussed for the different FIB application modes: cross-section imaging, specimen preparation for transmission electron microscopy, and via milling for device modification. It is shown that the material is more stable under the ion beam than under the electron beam in the scanning electron microscope (SEM) or in the transmission electron microscope (TEM). The milling of the material by H2O vapor assistance is strongly enhanced. Also by applying XeF2 etching an enhanced milling rate can be obtained so that both the polymer layer and the intermediate oxides can be etched in a single step.

Transmission Electron Microscopy (TEM) Specimen Preparation Technique using Focused Ion Beam (FIB): Application to Material Characterization of Chemical Vapor Deposition of Tungsten (W) and Tungsten Silicides (WSix)

1997 ◽  
Author(s):  
K. Doong ◽  
J.-M. Fu ◽  
Y.-C. Huang
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Chemical Vapor Deposition ◽  
Vapor Deposition ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Chemical Vapor ◽  
Specimen Preparation ◽  
Preparation Technique ◽  
Transmission Electron

Abstract The specimen preparation technique using focused ion beam (FIB) to generate cross-sectional transmission electron microscopy (XTEM) samples of chemical vapor deposition (CVD) of Tungsten-plug (W-plug) and Tungsten Silicides (WSix) was studied. Using the combination method including two axes tilting[l], gas enhanced focused ion beam milling[2] and sacrificial metal coating on both sides of electron transmission membrane[3], it was possible to prepare a sample with minimal thickness (less than 1000 A) to get high spatial resolution in TEM observation. Based on this novel thinning technique, some applications such as XTEM observation of W-plug with different aspect ratio (I - 6), and the grain structure of CVD W-plug and CVD WSix were done. Also the problems and artifacts of XTEM sample preparation of high Z-factor material such as CVD W-plug and CVD WSix were given and the ways to avoid or minimize them were suggested.

A Methodology to Reduce Ion Beam Induced Damage in TEM Specimens Prepared by FIB

2002 ◽  
Author(s):  
Chin Kai Liu ◽  
Chi Jen. Chen ◽  
Jeh Yan.Chiou ◽  
David Su
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Sample Preparation ◽  
Integrated Circuit ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Specimen Preparation ◽  
Tem Analysis ◽  
Sensitive Issue ◽  
Transmission Electron

Abstract Focused ion beam (FIB) has become a useful tool in the Integrated Circuit (IC) industry, It is playing an important role in Failure Analysis (FA), circuit repair and Transmission Electron Microscopy (TEM) specimen preparation. In particular, preparation of TEM samples using FIB has become popular within the last ten years [1]; the progress in this field is well documented. Given the usefulness of FIB, “Artifact” however is a very sensitive issue in TEM inspections. The ability to identify those artifacts in TEM analysis is an important as to understanding the significance of pictures In this paper, we will describe how to measure the damages introduced by FIB sample preparation and introduce a better way to prevent such kind of artifacts.

Comparison of Focused Ion Beam and Conventional Techniques on Tem Specimen Preparation of Metal-Ceramic Interfaces

1998 ◽  
Vol 4 (S2) ◽  
pp. 860-861 ◽  
Author(s):  
A. Ramirez de Arellano López ◽  
W.-A. Chiou ◽  
K. T. Faber
Keyword(s):  
Focused Ion Beam ◽  
Ceramic Coating ◽  
Steel Substrate ◽  
Ion Beam ◽  
Specimen Preparation ◽  
Inhomogeneous Materials ◽  
Cross Sectional ◽  
Fine Grain ◽  
Basic Industry ◽  
Coated Surface

The results of TEM analyses of materials are critically dependent on the quality of the sample prepared. Although numerous techniques have been developed in the last two decades, differential thinning of inhomogeneous materials remains a serious problem. Recently, focused ion beam (FIB) technique has been introduced for cross-sectional sample preparation for TEM and SEM.A novel system for depositing a fine-grain (∼ 200 nm) ceramic coating on a metal surface via a patent pending Small-Particle Plasma Spray (SPPS) technique has been developed at the Basic Industry Research Laboratory of Northwestern University. To understand the properties of the coated surface, the ceramic/metal interface and the microstructure of the ceramic coating must be investigated. This paper presents a comparison of the microstructure of an A12O3 coating on a mild steel substrate prepared using conventional and FEB techniques.

Sign in / Sign up

Export Citation Format

Share Document