scholarly journals Development of α+β-type biomedical Ti–Nb alloys with high oxygen content

2020 ◽  
Vol 321 ◽  
pp. 05003
Author(s):  
K. Ueda ◽  
M. Omiya ◽  
Y. Hirose ◽  
T. Narushima
Keyword(s):  
Oxygen Content ◽  
Low Cost ◽  
Total Elongation ◽  
Ti Alloy ◽  
High Oxygen Content ◽  
Β Phase ◽  
Α Phase ◽  
Heat Treated ◽  
Iced Water ◽  
Nb Content

Ti-(5–20)Nb-(0.5–1)O alloys (mass%) were investigated for developing low-cost biomedical α+β-type Ti alloy. Ti-(5, 10, 15, 20)Nb-(0.5, 0.75, 1)O alloys (mass%) were arc-melted and forged into bars. The forged alloy bars were heat-treated at 873 to 1373 K for 3.6 ks in an Ar atmosphere and quenched in iced water. β transus (Tβ) of the Ti-Nb-O alloys decreased with increasing Nb content. An increase in the oxygen content led to an increase in Tβ. After quenching, the formation of α′ martensite was observed in Ti-5Nb-yO alloys. An increase in the Nb content to 10 mass% led to the formation of α′ and α″ martensites. A further increase in the Nb content to 15 and 20mass% resulted in the formation of more α″ martensites. The boundary temperature for the formation of α′ and α″ martensite in the Ti-10Nb-yO alloys increased with increasing oxygen content, because oxygen enhances the Nb distribution to the β phase. The ultimate tensile strength of the Ti-xNb-0.75O alloys heattreated to obtain the α-phase fraction (fα) of 0.5 was over 1000 MPa, except for the Ti-15Nb-0.75O alloy. The total elongation decreased with increasing Nb content. The Ti-5Nb-0.75O alloy exhibited excellent strength-ductility balance as a low-cost α+β-type biomedical Ti alloy.

scholarly journals Effects of thermomechanical history and environment on the fatigue behavior of (β)-Ti-Nb implant alloys

2018 ◽  
Vol 165 ◽  
pp. 06001 ◽  
Author(s):  
André Reck ◽  
Stefan Pilz ◽  
Ulrich Thormann ◽  
Volker Alt ◽  
Annett Gebert ◽  
...  
Keyword(s):  
Fatigue Strength ◽  
Cyclic Loading ◽  
Fatigue Behavior ◽  
Fatigue Tests ◽  
Grain Structure ◽  
Fatigue Properties ◽  
Β Phase ◽  
Α Phase ◽  
Nb Content ◽  
Implant Alloys

This study examined the fatigue properties of a newly developed cast and thermomechanical processed (β)-Ti-40Nb alloy for a possible application as biomedical alloy due to exceptional low Young’s modulus (64-73 GPa), high corrosion resistance and ductility (20-26%). Focusing on the influence of two microstructural states with fully recrystallized β-grain structure as well as an aged condition with nanometer-sized ω-precipitates, tension-compression fatigue tests (R=-1) were carried out under lab-air and showed significant differences depending on the β-phase stability under cyclic loading. Present ω- precipitates stabilized the β-phase against martensitic α’’ phase transformations leading to an increased fatigue limit of 288 MPa compared to the recrystallized state (225 MPa), where mechanical polishing and subsequent cyclic loading led to formation of α’’-phase due to the metastability of the β-phase. Additional studied commercially available (β)-Ti-45Nb alloy revealed slightly higher fatigue strength (300 MPa) and suggest a change in the dominating cyclic deformation mechanisms according to the sensitive dependence on the Nb-content. Further tests in simulated body fluid (SBF) at 37°C showed no decrease in fatigue strength due to the effect of corrosion and prove the excellent corrosion fatigue resistance of this alloy type under given test conditions.

scholarly journals Phase transformations during continuous heating: effect of Sn addition on the microstructure of Ti-13Mo alloy

2020 ◽  
Vol 321 ◽  
pp. 05017
Author(s):  
M.G. de Mello ◽  
F.H. da Costa ◽  
R. Caram
Keyword(s):  
Lattice Parameter ◽  
Continuous Heating ◽  
Phase Precipitation ◽  
Heating Rates ◽  
Scanning Calorimetry ◽  
Β Phase ◽  
Ω Phase ◽  
Α Phase ◽  
Heat Treated ◽  
Kinetics Of

The addition of Sn to the Ti-Mo system can diminish the formation of ω phase and slow down the precipitation kinetics of α phase due to the low atomic diffusivity of Sn atoms in Ti. To explore α phase precipitation in Ti-13Mo and Ti-13Mo-6Sn (wt.%) alloys, differential scanning calorimetry (DSC) was applied using different heating rates to determine ω phase dissolution, α phase precipitation and β transus temperatures. The DSC results were then used to determine the aging heat treatment temperatures. Samples were heat-treated at 600 °C for 1 h and 24 h to examine microstructure features. The addition of Sn to Ti-13Mo alloy was found to increase the β phase lattice parameter, increasing β transus temperatures and resulting in microstructures with heterogeneous and coarser α phase precipitation.

Characterization of Ti-xNb (x = 25 – 35) Alloys in as Melt and Annealed States

2019 ◽  
Vol 946 ◽  
pp. 287-292
Author(s):  
Alexander Thoemmes ◽  
Ivan V. Ivanov ◽  
Alexey Ruktuev
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Xrd Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Β Phase ◽  
Α Phase ◽  
Nb Content ◽  
Scanning Electron

The effect of Nb content on microstructure, mechanical properties and phase formation in as-melt and annealed binary Ti-Nb alloys were investigated using scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX) and X-ray diffraction (XRD) analysis. The content of Nb varied in the range 25-35 mass % leading to significant changes in the microstructure. The annealed and furnace-cooled binary Ti-Nb samples exhibited HCP martensitic α` phase at a Nb content below 27.5 mass % and metastable BCC β phase at higher contents of Nb. The mechanical properties of alloys depended strongly on the Nb content and type of the dominating phase.

Microstructural Evaluation of Boron Free and Boron Containing Heat-Treated Ti-35Nb-7.2Zr-5.7Ta Alloy

2012 ◽  
Vol 18 (2) ◽  
pp. 295-303 ◽  
Author(s):  
Pallab Majumdar
Keyword(s):  
X Ray Diffraction ◽  
Second Stage ◽  
Β Phase ◽  
Solution Treated ◽  
Α Phase ◽  
Treatment Conditions ◽  
Transmission Electron ◽  
Heat Treated ◽  
Microstructural Evaluation ◽  
Diffraction Patterns

AbstractThe microstructure of Ti-35Nb-7.2Zr-5.7Ta (TNZT) and Ti-35Nb-7.2Zr-5.7Ta-0.5B (TNZTB) alloys under different heat treatment conditions has been analyzed. The solution-treated and water-quenched TNZT sample consists mainly of β phase with a very small amount of fine athermal ω precipitate. Precipitation of α can be observed when solution-treated samples are directly aged at 580°C for 8 h. The microstructure of the samples subjected to single-stage aging at 300°C or 400°C consists of ω precipitates in equiaxed β grains. Second stage aging at 580°C for 8 h after first stage of aging at 300°C or 400°C results in the replacement of ω precipitates by secondary α. In all of these samples, the amount of ω or α phase was very small, and therefore they could not be detected by X-ray diffraction studies. However, analysis of selected area diffraction patterns obtained from transmission electron microscopy studies confirms their presence. The addition of boron leads to the formation of dispersed precipitates of TiB in the β matrix of the TNZT alloy and also refines the β grains in the microstructure. However, other microstructural features of the TNZTB alloy are similar to those of the TNZT alloy.

Influence of Oxygen on Microstructures of Ti-Mo-Cr Alloy

2014 ◽  
Vol 896 ◽  
pp. 613-616 ◽  
Author(s):  
Junaidi Syarif ◽  
Eko Kurniawan ◽  
Mohd Rasidi Rasani ◽  
Zainuddin Sajuri ◽  
Mohd Zaidi Omar ◽  
...  
Keyword(s):  
Oxygen Content ◽  
Oxygen Concentration ◽  
Solid Solution Hardening ◽  
Stable Phase ◽  
Powder Metallurgy Method ◽  
Β Phase ◽  
Α Phase ◽  
Phase Calculation ◽  
Oxygen Addition ◽  
Effect Of Oxygen

In this study, the effect of oxygen addition on the microstructures of Ti-18%Mo-10%Cr alloy was investigated. The alloy was fabricated by a powder metallurgy method. The samples were subjected to sintering at 1300°C for 4 hours and furnace cooling. A Bo-Md method was initially applied for predicting stable phase. Calculation using the Bo-Md method showed that Ti-18%Mo-10%Cr alloy have bcc (β) phase at ambient temperature. All samples with various oxygen contents exhibited needle-like structures within equiaxed grains. The increase of oxygen content promoted formation of porosity in the α phase. Calculation of phase stability using JMatProTM showed that the decrease of β phase’s stability was not due to formation of the α phase on sintering, but due to promotion of nucleation and grain growth of diffusional α phase upon furnace cooling. It was also shown that vol.% of porosity of the alloy slightly increased with increasing oxygen content. Therefore, the increase of oxygen concentration could accelerate the formation of α phase and reduce the alloy’s density. The hardness increased as the oxygen concentration increased. The increase of the hardness might be due to combination of the solid solution hardening of oxygen and the precipitation hardening of α phase.

scholarly journals Element Distribution and Its Induced Peritectic Reaction during Solidification of Ti-Al-Nb Alloys

Metals ◽  
2021 ◽  
Vol 11 (9) ◽  
pp. 1386
Author(s):  
Xiangjun Xu ◽  
Junpin Lin ◽  
Chao Xiang ◽  
Yongfeng Liang
Keyword(s):  
Element Distribution ◽  
Solidification Path ◽  
Directionally Solidified ◽  
Al Content ◽  
Β Phase ◽  
Α Phase ◽  
Composition Segregation ◽  
Nb Content ◽  
The Difference ◽  
Mutual Conversion

The element distribution and the microstructures of directionally solidified ingots of Ti-45Al-8Nb and Ti-46Al-8Nb alloys were studied by scanning electron microscope (SEM) and electron probe microanalyzer (EPMA) equipped with wavelength-dispersive X-ray spectroscope (WDS). At high solidification rates, e.g., more than 50 μm/s, the ingot solidified in columnar β dendrites, while at low solidification rates, e.g., less than 30 μm/s, the solidification path changed from initial β solidification to L + β→α peritectic solidification, forming cellular dendrites with the β phase matrix surrounded by the α phase. The difference of Ti content in dendritic arms and interdendritic regions was not pronounced. The composition segregation was mainly caused by the mutual conversion of Al and Nb contents. Therefore, it was difficult to distinguish the variation of Ti in microstructure by EPMA-WDS map and line profiles. The composition of the peritectic α phase was different from that of the α phase transformed directly from the β phase. The Al content of the former was about 1 at% higher than that of the latter, while the Nb content was about 1 at% lower. The change of solidification path in the final solidified part resulted from the more severe segregation caused by slow solidification.

Comparison of Mechanical Properties and Microstructure of Annealed and Quenched Ti-Nb Alloys

2018 ◽  
Vol 769 ◽  
pp. 29-34 ◽  
Author(s):  
Alexander Thoemmes ◽  
Ivan V. Ivanov ◽  
Adelya A. Kashimbetova
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Xrd Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Β Phase ◽  
Α Phase ◽  
Nb Content ◽  
Scanning Electron

The effect of Nb content on microstructure, mechanical properties and phase formation in annealed and quenched binary Ti-Nb alloys were investigated using scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX) and X-ray diffraction (XRD) analysis. The content of Nb varied in the range 0-37 mass % leading to significant changes in the microstructure. The annealed and furnace-cooled binary Ti-Nb samples exhibited HCP martensitic α` phase at a Nb content below 14 mass % and stable BCC β phase at higher contents of Nb. The structure of the quenched samples changed with increase of Nb content in the following order: coarse primary martensite → fine acicular (α`+α``) martensite → single β phase structure. The mechanical properties of alloys strongly depended on the Nb content and type of the dominating phase.

Thermodynamic study at high temperature of the superconducting system YBa2Cu3Oz with 6

1987 ◽  
Vol 2 (6) ◽  
pp. 757-761 ◽  
Author(s):  
J. F. Marucco ◽  
C. Noguera ◽  
P. Garoche ◽  
G. Collin
Keyword(s):  
High Temperature ◽  
Large Deviations ◽  
Oxygen Content ◽  
Phase Stability ◽  
Stability Studies ◽  
Β Phase ◽  
Α Phase ◽  
Lower Oxygen ◽  
New Phase ◽  
Partial Oxygen

The YBa2Cu3Oz system has been investigated by thermogravimetry in a controlled partial oxygen pressure PO2 ranging from 105-10 Pa. A compound with z = 6.290 was prepared at T = 950°C and PO2 = 105 Pa and identified as a metastable β phase. Subsequent isothermal or isobar phase stability studies were performed. This β phase has a narrow metastability domain 6.25 <z < 6.50 at high temperature. By decreasing the temperature or increasing the PO2, the β phase transforms irreversibly into an α phase characterized by large deviations 7—x from stoichiometry. Near the stoichiometry z = 7, the structure of the a phase is orthorhombic, and fully ionized vacancies are likely to be predominant. By decreasing the PO2, the β phase transforms into a new phase with a lower oxygen content (z < 6.1).

scholarly journals Strengthening of a Near β-Ti Alloy through β Grain Refinement and Stress-Induced α Precipitation

Materials ◽  
2020 ◽  
Vol 13 (19) ◽  
pp. 4255 ◽  
Author(s):  
Wei Chen ◽  
Chao Li ◽  
Kangtun Feng ◽  
Yongcheng Lin ◽  
Xiaoyong Zhang ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
High Strength ◽  
Ti Alloy ◽  
Β Phase ◽  
Ti Alloys ◽  
Α Phase ◽  
Transmission Electron ◽  
Strength And Ductility ◽  
Α Particles

Near β-Ti alloys with high strength and good ductility are desirable for application in aviation and aerospace industries. Nevertheless, strength and ductility are usually mutually exclusive in structural materials. Here we report a new thermo-mechanical process, that is, the alloy was cross-rolled in β field then aged at 600 °C for 1 h. By such a process, a high strength (ultimate tensile strength: 1480 MPa) and acceptable ductility (elongation: 10%) can be simultaneously achieved in the near β-Ti alloy, based on the microscale β matrix and nanoscale α phase. The microstructure evolution, mechanical properties and strengthening mechanisms have been clarified by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The results showed that the grain size of the β phase progressively decreased with the increasing of rolling reduction. Moreover, dense dislocation structures and martensite phases distributed in the cross-rolled β matrix can effectively promote the precipitation of nanoscale α particles. TEM analyses confirmed that a heat-treatment twin was generated in the newly formed α lath during aging. These findings provide insights towards developing Ti alloys with optimized mechanical properties.

Sign in / Sign up

Export Citation Format

Share Document