The Relationship between Cake Strength of Potash Fertilizer and Initial Moisture Content, Particle Size, and Drying Time

2009 ◽  
Vol 27 (2) ◽  
pp. 166-176 ◽  
Author(s):  
Yan Wang ◽  
Richard W. Evitts ◽  
Robert W. Besant
Keyword(s):  
Particle Size ◽  
Moisture Content ◽  
Initial Moisture Content ◽  
Drying Time ◽  
Potash Fertilizer ◽  
The Relationship

Pengeringan Biji Kakao dengan Pengering Surya Tipe Terowong Berpenggerak Sel Fotovoltaik di Manokwari

Agrotek ◽  
2018 ◽  
Vol 2 (6) ◽  
Author(s):  
Wilson Palelingan Aman
Keyword(s):  
Moisture Content ◽  
Performance Test ◽  
Initial Moisture Content ◽  
Maximum Temperature ◽  
Photovoltaic Module ◽  
Cocoa Beans ◽  
Drying Time ◽  
Tunnel Dryer ◽  
Heat Collector ◽  
New Construction

<em>A research about cocoa beans drying used solar tunnel dryer with photovoltaic module driven have conducted in Manokwari. Solar tunnel dryer used in this research adapted from type Hohenheim with photovoltaic module and integrated air heat collector has been installed at the Department of Agricultural Technology, Papua State University Manokwari to dried cocoa beans. The objectives of this research were to design solar tunnel dryer and evaluate it�s performance in dryed cocoa beans. The result obtained was a new construction of solar tunnel dryer for cocoa beans with dimensions 6 m of length and 0,9 m of wide. The dryer completed with photovoltaic module to drive the blowers of hot drying air. �Performance test of the dryer showed that drying of 10 kg of cocoa beans with initial moisture content about 70% wet basis needed 13 hours of drying time to achieved final moisture content about 7,17% wet basis. The drying time achieved was faster compared than traditional solar drying that needed 20 hours of drying time. The maximum temperature achieved in drying chamber was 60 <sup>o</sup>C.</em>

scholarly journals Cherry Tomato Drying: Sun versus Convective Oven

Horticulturae ◽  
2021 ◽  
Vol 7 (3) ◽  
pp. 40
Author(s):  
Vincenzo Alfeo ◽  
Diego Planeta ◽  
Salvatore Velotto ◽  
Rosa Palmeri ◽  
Aldo Todaro
Keyword(s):  
Moisture Content ◽  
Initial Moisture Content ◽  
Drying Process ◽  
Drying Time ◽  
Oven Drying ◽  
Sun Drying ◽  
Different Temperatures ◽  
Final Water Content ◽  
Drying Curves ◽  
Drying Conditions

Solar drying and convective oven drying of cherry tomatoes (Solanum lycopersicum) were compared. The changes in the chemical parameters of tomatoes and principal drying parameters were recorded during the drying process. Drying curves were fitted to several mathematical models, and the effects of air temperature during drying were evaluated by multiple regression analyses, comparing to previously reported models. Models for drying conditions indicated a final water content of 30% (semidry products) and 15% (dry products) was achieved, comparing sun-drying and convective oven drying at three different temperatures. After 26–28 h of sun drying, the tomato tissue had reached a moisture content of 15%. However, less drying time, about 10–11 h, was needed when starting with an initial moisture content of 92%. The tomato tissue had high ORAC and polyphenol content values after convective oven drying at 60 °C. The dried tomato samples had a satisfactory taste, color and antioxidant values.

scholarly journals Lovastatin Production byAspergillus terreusUsing Agro-Biomass as Substrate in Solid State Fermentation

2012 ◽  
Vol 2012 ◽  
pp. 1-11 ◽  
Author(s):  
Mohammad Faseleh Jahromi ◽  
Juan Boo Liang ◽  
Yin Wan Ho ◽  
Rosfarizan Mohamad ◽  
Yong Meng Goh ◽  
...  
Keyword(s):  
Particle Size ◽  
Solid State ◽  
Moisture Content ◽  
Nitrogen Source ◽  
Solid State Fermentation ◽  
Incubation Temperature ◽  
Initial Moisture Content ◽  
Fermentation Time ◽  
Maximum Production ◽  
Additional Nitrogen

Ability of two strains ofAspergillus terreus(ATCC 74135 and ATCC 20542) for production of lovastatin in solid state fermentation (SSF) using rice straw (RS) and oil palm frond (OPF) was investigated. Results showed that RS is a better substrate for production of lovastatin in SSF. Maximum production of lovastatin has been obtained usingA. terreusATCC 74135 and RS as substrate without additional nitrogen source (157.07 mg/kg dry matter (DM)). Although additional nitrogen source has no benefit effect on enhancing the lovastatin production using RS substrate, it improved the lovastatin production using OPF with maximum production of 70.17 and 63.76 mg/kg DM forA. terreusATCC 20542 andA. terreusATCC 74135, respectively (soybean meal as nitrogen source). Incubation temperature, moisture content, and particle size had shown significant effect on lovastatin production (P<0.01) and inoculums size and pH had no significant effect on lovastatin production (P>0.05). Results also have shown that pH 6, 25°C incubation temperature, 1.4 to 2 mm particle size, 50% initial moisture content, and 8 days fermentation time are the best conditions for lovastatin production in SSF. Maximum production of lovastatin using optimized condition was 175.85 and 260.85 mg/kg DM forA. terreusATCC 20542 and ATCC 74135, respectively, using RS as substrate.

Stability of Thiamine and Riboflavin During Extrusion Processing of Triticale

1976 ◽  
Vol 39 (4) ◽  
pp. 244-245 ◽  
Author(s):  
G. BEETNER ◽  
T. TSAO ◽  
A. FREY ◽  
K. LORENZ
Keyword(s):  
Moisture Content ◽  
Multiple Regression ◽  
Temperature Effects ◽  
Initial Moisture Content ◽  
Final Moisture Content ◽  
Whole Grain ◽  
Moisture Contents ◽  
Extrusion Processing ◽  
Nozzle Size ◽  
The Relationship

Triticale kernels were extruded using a Brabender Plasticorder extruder with ¾-inch rifled barrel and 1:1 flight depth ratio screw. Whole grain samples were extruded at initial moisture contents of 15, 20, and 25%. Debranned samples were extruded at an initial moisture content of 22%. Barrel temperatures of 350, 400, and 450 F and nozzle openings of 1/8 inch and 1/16 inch were used. The products were analyzed for thiamine and riboflavin content. Results were corrected for final moisture content and expressed as fraction retained. A multiple regression was done to determine the relationship between independent and derived variables, and the retention. Riboflavin retention was correlated simply as a function of barrel temperature. Thiamine retention of the debranned material was correlated as a function of nozzle size and barrel temperature. Thiamine retention of the whole grain samples was correlated for nozzle size, first and second order temperature effects, and confounding between nozzle size and temperature.

scholarly journals Karakteristik Pengeringan Biji Jagung (Zea Mays L.) Menggunakan Alat Pengering Surya Adriyarkara Termodifikasi

2018 ◽  
Vol 3 (2) ◽  
pp. 351-360
Author(s):  
Athul Fadhli ◽  
Diswandi Nurba ◽  
Raida Agustina
Keyword(s):  
Zea Mays ◽  
Relative Humidity ◽  
Moisture Content ◽  
Zea Mays L ◽  
Initial Moisture Content ◽  
Solar Irradiation ◽  
Air Velocity ◽  
Drying Time ◽  
Average Temperature ◽  
Average Relative Humidity

Abstrak. Jagung merupakan tanaman penghasil karbohidrat terpenting. Pengeringan jagung pipil menggunakan alat pengering merupakan proses untuk menghasilkan jagung pipil yang siap diolah untuk pembuatan tepung jagung dengan batas kadar air tertentu sehingga menghaslkan jagung pipil dengan kualitas yang baik. Tujuan penelitian ini adalah untuk mengkaji karakteristik pengeringan biji jagung menggunakan alat pengering surya Termodifikasi. Metode penelitian  menggunakan 3,15 kilogram jagung pipil dengan kadar air awal 22% untuk proses pengeringan. Parameter yang dianalisis terkait alat pengering kolektor surya yaitu temperatur, kelembaban relatif, kecepatan udara dan iradiasi surya, sedangkan parameter yang dianalisis terkait bahan yaitu kadar air, lama waktu pengeringan, laju pengeringan dan organoleptik. Prosedur penelitian terdiri dari pengujian kosong dan pengujian dengan menggunakan jagung pipil. Hasil penelitian menunjukkan bahwa temperatur rata-rata dalam rak pengering sebelum dilakukan modifikasi yaitu 44,4oC, temperatur rata-rata setelah dilakukan modifikasi yaitu 55,5oC dan temperatur rata-rata rak pengering pada pengeringan menggunakan jagung pipil yaitu 46,96oC. Kelembaban relatif rata-rata dalam rak pengering sebelum dilakukan modifikasi yaitu 40,1%, kelembaban relatif rata-rata dalam rak pengering setelah modifikasi yaitu 35,1% dan kelembaban relatif rata-rata pengeringan menggunakan jagung pipil yaitu 44,45%. Dari hasil pengukuran tersebut menunjukkan bahwa nilai temperatur dan kelembaban pada alat setelah modifikasi lebih baik dibandingkan sebelum alat dimodifikasi. Pengukuran temperatur dan kelembaban relatif terdiri dari 4 titik pengukuran yaitu rak 1A,1B dan rak 2A, 2B. Kecepatan udara rata-rata yang diukur konstan yaitu 0,7 m/s pada ruang pengering, sedangkan lingkungan 1,1 m/s. Total iradiasi surya selama pengeringan yaitu 1848,84 W/m2. Kadar air jagung pipil masing-masing rak yaitu rak 1A 14,29%, rak 1B 14,47%, rak 2A 13,91% dan rak 2B 14,1%. Hasil dari pengujian organoleptik, panelis agak menyukai jagung pipil yang dikeringkan menggunakan alat pengering tersebut.Characteristics of Seed Drying (Zea mays L.) Using a Modified Adriyarkara Solar DryerAbstract. Corn is the most important carbohydrate plant. Drying corn using a drying tool is a process to produce corn that are ready to be processed for making corn flour with a certain water content limit so as to produce corn with good quality. The purpose of this study was to examine the characteristics of drying of corn kernels using a modified solar dryer. The research method used 3,15 kilogram of corn milled with the initial moisture content of 22% for drying process. The parameters analyzed in relation to solar collector dryers are temperature, relative humidity, air velocity and solar irradiation, while the parameters analyzed are materials such as moisture content, drying time, drying rate and organoleptic. The research procedure consists of unloaded testing and testing using corn. The results showed that the average temperature in the dryer tray before modification was 44,4°C, the average temperature after modification was 55,5°C and the average temperature of the dryer tray on drying using corn was 46,96oC. The average relative humidity in the dryer tray before modification is 40,1%, the average relative humidity in the dryer tray after modification is 35,1% and the average relative humidity of drying using corn is 44,45%. From the measurement results show that the value of temperature and humidity in the tool after modification is better than before. Measurement of temperature and relative humidity consist of 4 point of measurement that is tray 1A, 1B and tray 2A, 2B. Average mean air velocity measured is 0,7 m/s at the dryer room, while the environment is 1,1 m/s. Total solar irradiation during drying is 1848,84 W/m2. Moisture level of corn each shelves tray 1A is 14,29%, tray 1B is 14.47%, tray 2A is 13,91% and tray 2B is 14,1%. As a result of organoleptic testing, panelists rather like dried corn using the dryer.

scholarly journals Effect of Pads and Thickness of Paddy on Moisture Removal under Sun Drying

2021 ◽  
Author(s):  
A. Narmilan ◽  
G. Niroash ◽  
M.I.M. Mowjood ◽  
A.T.A. Akram
Keyword(s):  
Sri Lanka ◽  
Moisture Content ◽  
Removal Rate ◽  
Initial Moisture Content ◽  
Storage Period ◽  
Moisture Removal ◽  
Drying Time ◽  
Sun Drying ◽  
Regular Time ◽  
Paddy Farmers

Background: Sun drying is a popular post-harvest operation to maintain rice quality during the storage period. Farmers use different pads and thicknesses for sun drying of paddy in Ampara district, Sri Lanka. A study was conducted to evaluate the suitability and effectiveness of the drying pad and thickness as practiced by local paddy farmers during the sun drying process.Methods: The grain with an initial moisture content of 28% (dry basis) was sun dried with four types of drying pads and five levels of thickness of grain. This experiment was conducted between 8.30 am and 4.30 pm at the South Eastern University of Sri Lanka in August 2020. The moisture contents of the grain were measured at regular time intervals.Result: It was found that the duration of drying of paddy from 28% to 13% moisture content on a dry basis was 300 to 540 minutes depending upon the drying pad and thickness. The tarpaulin is reasonable at shallow thickness with less time to reach the necessary moisture level than other drying pads. Black polythene and fertilizer bag can be utilized for sun drying of paddy at 4 cm thickness with 130 minutes. It was found that with an increase in the thickness of paddy from 0.5 cm to 4 cm, the drying time increases. A statistically significant interaction was obtained between drying pads and thickness level on moisture removal of paddy. Therefore, the moisture removal rate differs with the drying pad and thickness of the paddy under open sun drying.

scholarly journals Study on collapsibility of typical structural loess by multi-parameter comparative analysis

2021 ◽  
Vol 293 ◽  
pp. 01032
Author(s):  
Liu Hongcheng ◽  
Lu Changwei ◽  
Wang Yinxia ◽  
Song Yi ◽  
Guan Xiangfeng ◽  
...  
Keyword(s):  
Particle Size ◽  
Comparative Analysis ◽  
Moisture Content ◽  
Composite Structure ◽  
Structural Parameters ◽  
Initial Moisture Content ◽  
Clay Content ◽  
Dry Density ◽  
Particle Content ◽  
Multiple Groups

To study the collapsibility of typical loess and its influencing factors in different areas, the samples in Jingyang, Lanzhou and Yili were studied. The correlation between initial moisture content, dry density, composition of particle size, structural parameters and the coefficient of subsidence is analyzed. The results show that: the coefficient of collapsibility is negatively correlated with the initial moisture content and dry density. In the experiments of multiple groups, the collapsibility coefficient has a certain correlation with the clay content, but not a uniform correlation with the particle content. The collapse coefficient is approximately positively correlated with the composite structure potential.

scholarly journals Ultrasound Drying of Rose Hips: a Process Study

2020 ◽  
Vol 50 (1) ◽  
pp. 79-86
Author(s):  
Elena Verboloz ◽  
Marina Ivanova ◽  
Vera Demchenko ◽  
Sergey Fartukov ◽  
Nikita Evona
Keyword(s):  
Vitamin C ◽  
Moisture Content ◽  
Quality Indicators ◽  
State Standard ◽  
Raw Materials ◽  
Initial Moisture Content ◽  
Raw Material ◽  
Drying Process ◽  
Resource Saving ◽  
Drying Time

Introduction. Rose hips are rich in macro- and micronutrients. Unfortunately, heat treatment destroys most nutrients. Ultrasonic technologies make it possible to reduce the drying time and lower the temperature regime. The research objective was to adjust ultrasound technology to rose hip production in order to reduce the loss of vitamins and improve the quality indicators of the dried product. Study objects and methods. The research featured rose hips of the Rosa canina species collected in the south of Kazakhstan. This subspecies of wild rose is poor in vitamin C. Nevertheless, this shrub is extremely common in Russia and other countries of the Commonwealth of Independent States. The raw material was dried according to standard methods. One group of samples was treated with ultrasound, while the other served as control. Both groups underwent a sensory evaluation and were tested for moisture and vitamin C. Results and discussion. The rose hips were dried in a combination steam oven with a built-in ultrasonic wave generator. The research revealed the following optimal parameters of the ultrasound drying process: frequency of ultrasonic vibrations – 22 kHz, processing time – 2.5 h, temperature in the combination steam oven – +56°C, initial moisture content – 30%. The resulting product met the requirements of State Standard. The loss of moisture was 57%. According to State Standard 1994-93, the initial moisture content should be 15% or less. Time decreased from 360 min to 160 min, and the initial moisture was 13%. The experiment confirmed the initial hypothesis that ultrasonic treatment improves the drying process by improving quality indicators and preserving vitamin C in raw materials using. Conclusion. Ultrasound treatment during moisture removal from rose hips provides a resource-saving technology that fulfills an economically and socially important function.

scholarly journals Optimization of the Cremator Settings for the Disposal of Poultry Waste By Incineration in a Beet-emitting Boiler

2020 ◽  
Author(s):  
Victor Konovalov ◽  
Anna Konovalova ◽  
Vladimir Konovalov ◽  
Sergey Denisov ◽  
Gali Gumarov
Keyword(s):  
Carbon Monoxide ◽  
Moisture Content ◽  
Regression Models ◽  
Initial Moisture Content ◽  
Ash Content ◽  
Chicken Manure ◽  
The Relationship ◽  
Heat Released ◽  
Carbon Monoxide Content ◽  
Continental Climate

The purpose of this work is to substantiate the parameters of the boiler unit, which ensures the cremation of manure using microwave radiation. The substantiation of the amount of heat released during the burning of chicken manure at the industrial keeping of poultry in the conditions of sharply continental climate on the basis of minimization of product utilization values - ash content of wastes and pollution of smoke emissions is presented. Using the obtained regression models of magnetron emission power, moisture content of the burnt manure mass, mass air consumption for the specified product utilization parameters, the analysis of the relationship between the obtained parameters is made. Correlation analysis has shown a high correlation between the amount of heat released during the combustion of manure and the concentration of carbon monoxide in the smoke emissions. Rationally, the value of carbon monoxide content in the flue gases is 3.9%, corresponding to the amount of heat released 2.1 MJ/kg at the combustion of a kilogram of manure at the ash content of the residue of 18.4% and the initial moisture content of the manure of 38.4%. It provides power of radiation of magnetron 400 W on 1 kg of a waste and the mass flow rate of air of 13.8 kg/h.

scholarly journals Modelling of biomass temperature in the drying process

2020 ◽  
Vol 154 ◽  
pp. 01004
Author(s):  
Ewa Golisz ◽  
Małgorzata Jaros ◽  
Szymon Głowacki
Keyword(s):  
Moisture Content ◽  
Initial Moisture Content ◽  
Direct Calculation ◽  
Logistic Function ◽  
Temperature Model ◽  
Drying Process ◽  
Drying Time ◽  
Temperature Changes ◽  
Higher Temperature ◽  
Temperature Rate

The goal of the work was to propose and verify the model of temperature changes of the convective dried biomass depending on the drying time. The algebraic temperature model of the convective dried solid, giving the possibility of its direct calculation, was based on the logistic function of growth. Temperature model was verified for convective dried biomass: vegetable and wood (poplar and willow wood chips) significantly differing in initial moisture content. Parameter W in the temperature model, defined as the coefficient of temperature rate changes reaches greater values in higher temperature of drying air and for wood biomass which has lower initial moisture content. Empirically selected parameter W allows to verify the temperature model with the relative error less than 5%.

Sign in / Sign up

Export Citation Format

Share Document