scholarly journals On the reduction of hydraulic resistance based on the hydrophobization of functional surfaces

2021 ◽  
Vol 2124 (1) ◽  
pp. 012018
Author(s):  
M R Dasaev ◽  
E S Trushin ◽  
O V Kalakutskaya ◽  
A P Voloshenko
Keyword(s):  
Contact Angle ◽  
Reynolds Number ◽  
Hydraulic Resistance ◽  
Experimental Studies ◽  
Hydrophobic Surfaces ◽  
Hydraulic Losses ◽  
Water Transportation ◽  
Laser Equipment ◽  
Functional Surfaces ◽  
Experimental Tube

Abstract Analysis of various studies has shown that one of the most promising ways to reduce hydraulic resistance in pipelines during transportation of liquid fluid is a method based on changing the wettability of functional surfaces, i.e. hydrophobization. This paper presents the results of experimental studies of the effect of hydrophobization of pipe surfaces on hydraulic losses. For this purpose, experimental tube samples of steel (20Kh13) were made, on the surface of which a spiral relief was formed using laser equipment, resulting in a hydrophobic state, and the value of the contact angle was 160.7°. From the analysis of the results of experimental studies, the dependence of hydraulic resistance on Reynolds number was obtained, from which it follows that the use of hydrophobic surfaces during water transportation helps to reduce the hydraulic resistance to 9.7%.

scholarly journals Capacitance Effects of a Hydrophobic-Coated Ion Gel Dielectric on AC Electrowetting

Micromachines ◽  
2021 ◽  
Vol 12 (3) ◽  
pp. 320
Author(s):  
Taewoo Lee ◽  
Sung-Yong Park
Keyword(s):  
Contact Angle ◽  
Experimental Studies ◽  
Frequency Region ◽  
Mixing Enhancement ◽  
High Capacitance ◽  
Angle Change ◽  
Gel Layer ◽  
Resonance Frequencies ◽  
Ion Gel ◽  
Capacitance Effects

We present experimental studies of alternating current (AC) electrowetting dominantly influenced by several unique characteristics of an ion gel dielectric in its capacitance. At a high-frequency region above 1 kHz, the droplet undergoes the contact angle modification. Due to its high-capacitance characteristic, the ion gel allows the contact angle change as large as Δθ = 26.4°, more than 2-fold improvement, compared to conventional dielectrics when f = 1 kHz. At the frequency range from 1 to 15 kHz, the capacitive response of the gel layer dominates and results in a nominal variation in the angle change as θ ≈ 90.9°. Above 15 kHz, such a capacitive response of the gel layer sharply decreases and leads to the drastic increase in the contact angle. At a low-frequency region below a few hundred Hz, the droplet’s oscillation relying on the AC frequency applied was mainly observed and oscillation performance was maximized at corresponding resonance frequencies. With the high-capacitance feature, the ion gel significantly enlarges the oscillation performance by 73.8% at the 1st resonance mode. The study herein on the ion gel dielectric will help for various AC electrowetting applications with the benefits of mixing enhancement, large contact angle modification, and frequency-independent control.

Flow and Thermal Fields in a Pendant Droplet Moving on Lyophobic Surface

2010 ◽  
Author(s):  
Basant Singh Sikarwar ◽  
K. Muralidhar ◽  
Sameer Khandekar
Keyword(s):  
Heat Transfer ◽  
Contact Angle ◽  
Reynolds Number ◽  
Shear Stress ◽  
Heat Transfer Coefficient ◽  
Wall Shear Stress ◽  
Transfer Coefficient ◽  
Maximum Shear Stress ◽  
Computational Domain ◽  
Wall Shear

Clusters of liquid drops growing and moving on physically or chemically textured lyophobic surfaces are encountered in drop-wise mode of vapor condensation. As opposed to film-wise condensation, drops permit a large heat transfer coefficient and are hence attractive. However, the temporal sustainability of drop formation on a surface is a challenging task, primarily because the sliding drops eventually leach away the lyophobicity promoter layer. Assuming that there is no chemical reaction between the promoter and the condensing liquid, the wall shear stress (viscous resistance) is the prime parameter for controlling physical leaching. The dynamic shape of individual droplets, as they form and roll/slide on such surfaces, determines the effective shear interaction at the wall. Given a shear stress distribution of an individual droplet, the net effect of droplet ensemble can be determined using the time averaged population density during condensation. In this paper, we solve the Navier-Stokes and the energy equation in three-dimensions on an unstructured tetrahedral grid representing the computational domain corresponding to an isolated pendant droplet sliding on a lyophobic substrate. We correlate the droplet Reynolds number (Re = 10–500, based on droplet hydraulic diameter), contact angle and shape of droplet with wall shear stress and heat transfer coefficient. The simulations presented here are for Prandtl Number (Pr) = 5.8. We see that, both Poiseuille number (Po) and Nusselt number (Nu), increase with increasing the droplet Reynolds number. The maximum shear stress as well as heat transfer occurs at the droplet corners. For a given droplet volume, increasing contact angle decreases the transport coefficients.

Vortex-Induced Vibrations of a Cylinder at Subcritical Reynolds Number

2011 ◽  
Author(s):  
Yoann Jus ◽  
Elisabeth Longatte ◽  
Jean-Camille Chassaing ◽  
Pierre Sagaut
Keyword(s):  
Reynolds Number ◽  
Numerical Simulations ◽  
Numerical Study ◽  
Damping Ratio ◽  
Experimental Studies ◽  
Cross Flow ◽  
Physical Analysis ◽  
Arbitrary Lagrangian Eulerian ◽  
Vortex Induced Vibrations ◽  
Low Mass

The present work focusses on the numerical study of Vortex-Induced Vibrations (VIV) of an elastically mounted cylinder in a cross flow at moderate Reynolds numbers. Low mass-damping experimental studies show that the dynamic behavior of the cylinder exhibits a three-branch response model, depending on the range of the reduced velocity. However, few numerical simulations deal with accurate computations of the VIV amplitudes at the lock-in upper branch of the bifurcation diagram. In this work, the dynamic response of the cylinder is investigated by means of three-dimensional Large Eddy Simulation (LES). An Arbitrary Lagrangian Eulerian framework is employed to account for fluid solid interface boundary motion and grid deformation. Numerous numerical simulations are performed at a Reynolds number of 3900 for both no damping and low-mass damping ratio and various reduced velocities. A detailed physical analysis is conducted to show how the present methodology is able to capture the different VIV responses.

Quantitative Experimental Study of SiO2-Water Nanofluids on Backward-Facing Step Flow under Low Reynolds Number

2018 ◽  
Vol 916 ◽  
pp. 221-225
Author(s):  
Ji Zu Lv ◽  
Liang Yu Li ◽  
Cheng Zhi Hu ◽  
Min Li Bai ◽  
Sheng Nan Chang ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Reynolds Number ◽  
Volume Fraction ◽  
Pure Water ◽  
Experimental Studies ◽  
Flow Characteristics ◽  
Thermal Engineering ◽  
Heat Transfer Medium ◽  
Step Flow

Nanofluids is an innovative study of nanotechnology applied to the traditional field of thermal engineering. It refers to the metal or non-metallic nanopowder was dispersed into water, alcohol, oil and other traditional heat transfer medium, to prepared as a new heat transfer medium with high thermal conductivity. The role of nanofluids in strengthening heat transfer has been confirmed by a large number of experimental studies. Its heat transfer mechanism is mainly divided into two aspects. On the one hand, the addition of nanoparticles enhances the thermal conductivity. On the other hand, due to the interaction between the nanoparticles and base fluid causing the changes in the flow characteristics, which is also the main factor affecting the heat transfer of nanofluids. Therefore, a intensive study on the flow characteristics of nanofluids will make the study of heat transfer more meaningful. In this experiment, the flow characteristics of SiO2-water nanofluids in two-dimensional backward step flow are quantitatively studied by PIV. The results show that under the same Reynolds number, the turbulence of nanofluids is larger than that of pure water. With the increase of nanofluids volume fraction, the flow characteristics are constantly changing. The quantitative analysis proved that the nanofluids disturbance was enhanced compared with the base liquid, which resulting in the heat transfer enhancement.

Moderate Reynolds Number Mixing in a T-Channel

2010 ◽  
Author(s):  
Susan Thomas ◽  
Tim Ameel
Keyword(s):  
Reynolds Number ◽  
Cross Section ◽  
Rectangular Cross Section ◽  
Large Body ◽  
Experimental Studies ◽  
Numerical Work ◽  
Moderate Reynolds Number ◽  
Wide Range ◽  
Particle Imaging ◽  
Experimental Trials

An experimental investigation of water flow in a T-shaped channel with rectangular cross section (20 × 20 mm inlet ID and 20 × 40 mm outlet ID) has been conducted for a Reynolds number Re range of 56 to 422, based on inlet diameter. Dynamical conditions and the T-channel geometry of the current study are applicable to the microscale. This study supports a large body of numerical work, and resolution and the interrogation region are extended beyond previous experimental studies. Laser induced fluorescence (LIF) and particle imaging velocimetry (PIV) are used to characterize flow behaviors over the broad range of Re where realistic T-channels operate. Scalar structures previously unresolved in the literature are presented. Special attention is paid to the unsteady flow regimes that develop at moderate Re, which significantly impact mixing but are not yet well characterized or understood. An unsteady symmetric topology, which develops at higher Re and negatively impacts mixing, is presented, and mechanisms behind the wide range of mixing qualities predicted for this regime are explained. An optimal Re operating range is identified based on multiple experimental trials.

Preparation of Super Hydrophobic Surfaces by the Stainless Steel Wire Mesh as Templates

2012 ◽  
Vol 562-564 ◽  
pp. 56-59 ◽  
Author(s):  
Jian Zhuang ◽  
Meng Meng Du ◽  
Heng Zhi Cai ◽  
Ya Jun Zhang ◽  
Da Ming Wu
Keyword(s):  
Contact Angle ◽  
Stainless Steel ◽  
Steel Wire ◽  
Contact Angles ◽  
Wire Mesh ◽  
Stainless Steel Wire ◽  
Hydrophobic Surfaces ◽  
Water Contact ◽  
Stainless Steel Wire Mesh ◽  
Steel Wire Mesh

A facile method for manufacturing super hydrophobic surfaces is presented using the stainless steel wire mesh as templates. The rough surfaces of polymers including polycarbonate, polypropylene and PMMA are prepared with hot embossing on different specifications of stainless steel wire mesh. Scanning electron microscopy (SEM) results reveal that the surfaces roughness of the polymers can be controlled by selecting templates. Contact angle measurement shows that the water contact angles(WCA) rise with the increase of surface roughness, especially, the water contact angle on the PC surfaces prepared with specifications of 635mesh screen can reach to 152.3°, alias super hydrophobic surfaces.

scholarly journals Wettability on Different Surfaces

2020 ◽  
Author(s):  
Yeeli Kelvii Kwok
Keyword(s):  
Contact Angle ◽  
Textured Surface ◽  
Original Material ◽  
Textured Surfaces ◽  
Hydrophobic Surfaces ◽  
Hydrophilic Surfaces ◽  
Young's Equation

Wettability has been explored for 100 years since it is described by Young’s equation in 1805. It is all known that hydrophilicity means contact angle (θ), θ < 90°; hydrophobicity means contact angle (θ), θ > 90°. The utilization of both hydrophilic surfaces and hydrophobic surfaces has also been achieved in both academic and practical perspectives. In order to understand the wettability of a droplet distributed on the textured surfaces, the relevant models are reviewed along with understanding the formation of contact angle and how it is affected by the roughness of the textured surface aiming to obtain the required surface without considering whether the original material is hydrophilic or hydrophobic.

Sign in / Sign up

Export Citation Format

Share Document