scholarly journals Extraction of magnesium from salt pond waste with low lithium grade using sodium silicate reagent

2021 ◽  
Vol 1195 (1) ◽  
pp. 012028
Author(s):  
E Sulistiyono ◽  
S Harjanto ◽  
L H Lalasari
Keyword(s):  
Chemical Composition ◽  
Pharmaceutical Industry ◽  
Production Process ◽  
Sodium Silicate ◽  
Liquid Waste ◽  
Magnesium Silicate ◽  
Raw Material ◽  
Magnesium Ion ◽  
Salt Pond ◽  
Salt Production

Abstract Nowadays, Indonesia’s salt production process has shifted from a traditional salt pond process to a salt pond with a geomembrane tarpaulin system. This system has the advantage of producing a faster salting process and a better salt quality and producing a thick yellow liquid waste known as bittern. The waste produced has not been fully utilized, even though the waste contains valuable elements, namely magnesium, lithium, and others. This paper investigates the potential utilization of bittern by extracting magnesium from by-product salt pond using sodium silicate reagent with various concentrations of 125–250 g/l. The bittern used in this experiment had the chemical composition as follows: 33,184 ppm magnesium (Mg), 23,787 ppm sodium (Na), 6.1 ppm lithium (Li), 5,491 ppm potassium (K), 617 ppm calcium (Ca), 152 ppm boron (B). The highest removal of magnesium ion by addition of sodium silicate of 250 g/l was about 96.2%. The results showed that the solid products were magnesium silicate precipitates without containing asbestos compounds. The magnesium silicate precipitate product can be applied as talc raw material for the pharmaceutical industry.

scholarly journals Garam Indonesia Berkualitas: Studi Kandungan Logam Berat Timbal (Pb) Pada Garam [The Quality of Indonesia Salt: Study of Heavy Metal Lead (Pb) Levels in the Salt]

2019 ◽  
Vol 11 (1) ◽  
pp. 43
Author(s):  
Nurus Samsiyah ◽  
Anita Dewi Moelyaningrum ◽  
Prehatin Trirahayu Ningrum
Keyword(s):  
Heavy Metal ◽  
Production Process ◽  
Descriptive Analysis ◽  
Raw Material ◽  
Soil Environment ◽  
Salt Production ◽  
Pb Contamination ◽  
Production Processes ◽  
Post Production

AbstrakKualitas garam sangat ditentukan oleh perlakuan dan penanganan yang diberikan pada saat pra produksi, proses produksi maupun pasca produksi. Kontaminan Pb dalam garam dapat bersumber dari lingkungan perairan laut sebagai bahan baku, tanah sebagai media / tempat produksi garam dan lingkungan udara dimana proses produksi garam berlangsung di lahan terbuka. Tujuan penelitian ini adalah untuk menganalisis kadar logam berat timbal (Pb) dalam garam di Kabupaten Pamekasan. Jenis penelitian ini adalah jenis deskriptif. Teknik pengumpulan data penelitian melalui observasi dan wawancara. Hasil observasi menunjukkan bahwa rata-rata kadar logam berat timbal (Pb) di Kabupaten Pamekasan masih di bawah batas maksimum yang telah ditentukan dalam SNI 3556-2010 dan SNI 7387-2009 yaitu <10 ppm dengan kadar Pb terendah 0,066 ppm dan tertinggi 0,162 ppm. Proses produksi garam kurang sesuai dengan standar yang telah ditetapkan. Oleh karena itu, perlunya penangangan yang baik pada pra produksi, proses produksi hingga pasca produksi pembuatan garam agar kadar Pb tidak meningkat.AbstractThe quality of salt is very determined by the treatment and handling given during the pre-production, production and post-production processes. Pb contamination in salt can be sourced from the marine environment as raw material in the process of making salt, the soil environment as a medium / place of salt production and the air environment where the salt production process takes place in an open area. The aim of research was to analyze levels of lead heavy metals (Pb) of salt in Pamekasan Regency. This research is a descriptive analysis. The techniques of data collecting of this research are observation and interview. Observations indicate that the average level of heavy metal lead (Pb) in Pamekasan regency is still below the maximum limit specified in SNI 3556-2010 and SNI 7387-2009 is <10 ppm which is the lowest grade of 0.066 ppm and grade the highest is 0.162 ppm. The salt production process is not in accordance with established standards The Therefore, the need for good handling in pre-production, production processes to post-production of salt production so that Pb levels do not increase.

scholarly journals PELUANG PENERAPAN PRODUKSI BERSIH PADA KAWASAN INDUSTRI PERIKANAN MUNCAR KABUPATEN BANYUWANGI JAWA TIMUR

2016 ◽  
Vol 11 (1) ◽  
pp. 95 ◽  
Author(s):  
Lestario Widodo
Keyword(s):  
Production Process ◽  
Liquid Waste ◽  
Production Method ◽  
Cleaner Production ◽  
Raw Material ◽  
Industrial Implementation ◽  
Main Input ◽  
The Impact ◽  
Unpleasant Smell ◽  
Excessive Water

Coastal areas in Muncar Banyuwangi has developed one of the largest fisherys industry centers in Indonesia. Fisherys industry in the production process using a fish as a main input and also need a lot of clean water. The impact of these activities is the occurrence of environmental pollution in the form of liquid waste and the unpleasant smell. Cleaner produktion is minimization of waste from source. The application of cleaner production with its assessment and identification to production process will create any innovations. In the cleaner production method contains several strategies that can be implemented forreducing and minimizing of industrial waste including prevention, recycling, treatment and disposing. One of prospective instruments that can be developed further in the industrial implementation of cleaner production is fisherys industry at Muncar Banyuwangi. The main opportunities to implementation of cleaner production, especially in stages using excessive water in the process of weeding and cleaning fish, stage of the main raw material the use of fish by re-sorting a more effective, and efficient charging process scattered on the tin.Key words : Cleaner production, fisherys industry

scholarly journals Production, Characterization, and Sensory Profiling of Novel Pepper Distilled Spirit

2021 ◽  
Vol 2021 ◽  
pp. 1-8
Author(s):  
Yap Chin Ann ◽  
Foo See Wei ◽  
Gilbert Yeo ◽  
Teow Wei Ping ◽  
Lawrence Tuah
Keyword(s):  
Chemical Composition ◽  
Production Process ◽  
Descriptive Analysis ◽  
Fermentation Medium ◽  
Extraction Process ◽  
Raw Material ◽  
Sensory Profile ◽  
Human Consumption ◽  
Composition Analysis ◽  
Organoleptic Quality

This study described the production method of novel whiskey using black pepper berries as raw material including the determination of chemical composition and sensory profile of this distillate. The production process consisted of production of fermentation medium via hydrothermal treatment, followed by fermentation and distillation. The incorporation of hydrothermal extraction process makes this whiskey production process differ from the existing commercial spirit production protocol. Chemical composition analysis showed that there were 12 main volatile compounds that contribute to the aroma profile of this pepper whiskey which consisted of 1 aldehyde group, 3 ester groups, 2 phenolic compounds, and 6 alcohol groups. All of these compounds are presented at different concentrations that are able to give pleasant and signature aroma to this spirit. A 10-member descriptive analysis panel conducted showed that 7 descriptors can be used to define the organoleptic quality of this whiskey, namely, clarity and brilliance (visual), fruity and flora (aroma), spiciness and sweetness (taste), and fruity mouthfeels. In conclusion, pepper berries can be used as raw material for pepper whiskey production and having organoleptic quality acceptable for human consumption.

scholarly journals Produksi Garam Dan Bittern Di Tambak Garam

2016 ◽  
Vol 19 (1) ◽  
pp. 43
Author(s):  
Nur Taufiq Syamsudin Putra Jaya ◽  
Retno Hartati ◽  
Widianingsih Widianingsih
Keyword(s):  
Sea Water ◽  
High Tide ◽  
Raw Material ◽  
Basic Technique ◽  
Salt Pond ◽  
Salt Production ◽  
The Road ◽  
High Production ◽  
Collection Point ◽  
Very High

Rembang Regency could be named as Salt City because they have very high production after Pati Regency. Along the road of Juwana (Pati) - Rembang, salt pond could be seen as square salt sea equipped with windmill to take the sea water from the channel into the pond and is processed into salt. Although salt localproduction is sufficient enough for raw material of industry, therefore best practical technology it is needed. The objective of present work are  to improve directly the process of salt production and basic technique for diversiificatio of salt production, i.e. salt and bittern. The result of present works as follows. Getrape type salt pond is applied, where  young water embankment is located upstream and the down to seed pond 1, 2, 3, then distributed to cristalization pan. Seawater is taken through primary dykes to pump at elevation of 1.5 m, so still full of water during high tide. On cristalization pan (size of 200 m2) sea water will be settled during 7–10 days until its cristalized. Salt cristal was located under bittern solution could be scrap and collected in collection point.  The left-after bittern of 29–30° Be could be flowed back into seed pan uo be collected in bitter collection point.  Keywords: Rembang, salt, bittern

Problems Facing the Arab Pharmaceutical Industry: A Case Study from Yemen

2016 ◽  
Vol 2 (4) ◽  
pp. 234-241
Author(s):  
Mohammed Al-Shakka ◽  
Ebtesam Abood ◽  
Adel Al-Dhubhany ◽  
Sami Abdo Radman Aldubai ◽  
Khaled Said ◽  
...  
Keyword(s):  
Pharmaceutical Industry ◽  
Low Income ◽  
Well Being ◽  
Pharmaceutical Products ◽  
Domestic Market ◽  
Raw Material ◽  
Political Crisis ◽  
Pharmaceutical Manufacturer ◽  
University Graduates ◽  
Pharmaceutical Drugs

Because of the almost-instant connection with the welfare and well-being of individuals, pharmaceutical industry stands prominently as a very important factor for the improvement and progress of a healthy productive nation. These days, pharmaceutical industry thrives as one of the largest and exponentially expanding global industries. Nonetheless, millions of people in low income developing countries, have to suffer from the fatal consequences of the inaccessibility and non-availability of essential drugs. This is also happening in Yemen, where the pharmaceutical manufacturers sector have to face up to many challenges. The Yemen Drug Company (YEDCO) was founded in 1964 by the Yemeni government as it collaborated with private investors. It was endorsed as a company with the expertise in the medicinal drug marketing. YEDCO started its work by taking in drugs from foreign companies and then locally marketing and distributing them. In 1982, YEDCO built the first medicinal factory for drugs in Sana’a. Since then, seven companies were set up to manufacture medicines in Yemen. The expanding population has led to the need to have more pharmaceutical products. It may be understandable that pharmaceutical manufacturer companies are also hit by the political crisis in the country. Inadequate amount of fuel and raw material as well as low security status were some of the underlying factors behind these ill-effects in Yemen. Imported drugs make up about nearly 90% % of the pharmaceutical market compared to 10% drugs from the domestic market. This situation has led to an additional burden being shouldered by the national economy, where Yemen spends about US$263 million annually on pharmaceutical drugs, in reference to the national Supreme Drugs Authority. Although there is a very quick growth in the population and drugs consumption, the pharmaceutical industry has not been very active, where global pharmaceutical products play their role dominantly on the domestic market. The pharmaceutical production necessitates skilled human resources like university graduates. By contrast, the government and the private sector should also motivate the pharmaceutical industry and make use of the local employment

Leaching Studies of Cement-Glass Package Containing Sodium Borate

1986 ◽  
Vol 84 ◽  
Author(s):  
Masahiro Okamoto ◽  
Koichi Chino ◽  
Tsutomu Baba ◽  
Tatsuo Izumida ◽  
Fumio Kawamura ◽  
...  
Keyword(s):  
Sodium Silicate ◽  
Liquid Waste ◽  
Sodium Borate ◽  
Pressurized Water Reactor ◽  
X Ray Diffraction ◽  
Adsorption Ability ◽  
Pressurized Water ◽  
X Ray ◽  
Solidification Reaction ◽  
Main Components

AbstractA new solidification technique using cement-glass, which is a mixture of sodium silicate, cement, additives, and initiator of the solidification reaction, was developed for sodium borate liquid waste generated from pressurized water reactor (PWR) plants. The cement-glass could solidify eight times as much sodium borate as cement could, because the solidifying reaction of the cement-glass is not hindered by borate ions.The reaction mechanism of sodium silicate and phosphoric silicate (initiator), the main components of cement-glass, was studied through X-ray diffraction and compressive strength measurements. It was found that three- dimensionally bonded silicon dioxide was produced by polymerization of the two silicates. The leaching ratio of cesium from the cement-glass package was one-tenth that of the cement one. This low value was attributed to a high cesium adsorption ability of the cement-glass and it could be theoretically predicted accordingly.

PEAS AND PRODUCTS OF ITS PROCESSING OF - NONCONVENTIONAL RAW MATERIAL RESOURCES

2020 ◽  
Author(s):  
D.Y. Bolgova ◽  
◽  
N.A. Tarasenko ◽  
Z.S. Mukhametova ◽  
◽  
...  
Keyword(s):  
Chemical Composition ◽  
Human Health ◽  
Food Production ◽  
Food Industry ◽  
Raw Material ◽  
Plant Proteins ◽  
Material Resources ◽  
The Rich

Nutrition is an important factor that affects human health. The use of plant proteins as various additives in food production has now been actively developed. The rich chemical composition of pea grains determines the possibility of application in the food industry. Peas are characterized by good assimilability and degree of digestion.

Processed Gingers: Current and Prospective Use in Food, Cosmetic, and Pharmaceutical Industry

2019 ◽  
Vol 10 (1) ◽  
pp. 20-26 ◽  
Author(s):  
Jae-Suk Choi
Keyword(s):  
Pharmaceutical Industry ◽  
Adverse Effects ◽  
Shelf Life ◽  
Traditional Medicine ◽  
Functional Foods ◽  
Zingiber Officinale ◽  
Raw Material

Ginger (Zingiber officinale) has been widely used in traditional medicine, and as raw material for cosmetics, beverages, and health functional foods. However, some adverse effects of ginger have been reported. In addition, the hot and pungent taste of ginger leads to reduced consumption. To overcome these problems, methods for the production of fermented, steamed (or steamed-dried), aged, roasted and beopje ginger have been developed. This review provides an overview and summary of new ginger processing procedures, including methods to reduce the pungent flavor of ginger, extend shelf-life, increase the health-functional compound content, and improve safety. These attempts might improve the consumption of ginger as well as prospective applications of processed ginger for food, cosmetics, and the pharmaceutical industry, also as discussed in various patents.

scholarly journals Geochemistry and Mineralogy of Ice-Dammed Lake Sediments of the Lębork Deposit

2021 ◽  
Author(s):  
Radosław Rogoziński ◽  
Alina Maciejewska
Keyword(s):  
Chemical Composition ◽  
Lake Sediments ◽  
Inductively Coupled Plasma ◽  
Mineralogical Composition ◽  
Raw Material ◽  
Element Analysis ◽  
X Ray ◽  
Dominant Component ◽  
Clay Deposits ◽  
Dammed Lake

AbstractVarved clay deposits from ice-dammed lakes are a particularly important and broadly applied raw material used for the production of high-quality ceramics (red bricks, roof tiles, etc.), but the mineralogy and geochemistry of these sediments are not fully understood. The aim of the present study was to determine the chemical and mineralogical composition of ice-dammed lake sediments of the Lębork deposit. Major-element analysis of the compositions of selected samples from the ice-dammed lake clays was performed by X-ray fluorescence (XRF) and trace elements were determined by inductively coupled plasma-mass spectrometry. The mineralogical composition of clay samples was determined by X-ray diffraction (XRD). Analyses of the chemical composition of the ice-dammed lake clays of the Lębork deposit showed that the dominant component was SiO2 with a mean content of 56.13 wt.%; the second most abundant component was Al2O3, with a mean content for the entire deposit of 11.61 wt.%. Analysis by ICP-MS indicated the presence of rare earth elements (REE), e.g. cerium, neodymium, lanthanum, and praseodymium; their mean contents are: 56.9, 27.0, 26.3, and 7.3 ppm, respectively. Mineralogical analysis of the varved clays identified quartz, muscovite, calcite, and clay minerals – illite, kaolinite, and montmorillonite. The material filling the Lębork basin is characterized by small lateral and vertical variability in chemical composition. The results of the present study may be of considerable importance in determining the parent igneous, metamorphic, and sedimentary rocks, the weathering products of which supplied material to the ice-dammed lake, as well as in determining the mechanisms and character of the sedimentation process itself.

Sign in / Sign up

Export Citation Format

Share Document