The mechanical properties of perfect crystals I. The ideal strength

1972 ◽  
Vol 330 (1582) ◽  
pp. 291-308 ◽  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Shear Strength ◽  
Sodium Chloride ◽  
Room Temperature ◽  
Cleavage Plane ◽  
Ideal Strength ◽  
Lennard Jones ◽  
Computer Calculations ◽  
The Ideal

In this paper we present computer calculations of the ideal strength of crystals of sodium chloride and argon, for a variety of modes of homogeneous deformation. As models of the interatomic binding we employ the simple, two-body, central-force Born-Mayer and Lennard-Jones potentials respectively. The calculations for argon are appropriate to absolute zero, those for sodium chloride to room temperature. The results indicate a very marked anisotropy of the ideal tensile strength for sodium chloride, with a pronounced minimum at <100>, which is consistent with the observed cleavage on this plane. The ideal tensile strength of argon is shown to be much less dependent on orientation, which accords with the lack of any obvious cleavage plane in this material. We also make some estimates of the ideal shear strength, and find this to be a minimum for {111} <112> shear for both argon and sodium chloride.

scholarly journals Effects of Substitution of Y with Yb and Ce on the Microstructures and Mechanical Properties of Mg88.5Zn5Y6.5

Metals ◽  
2020 ◽  
Vol 11 (1) ◽  
pp. 31
Author(s):  
Hongxin Liao ◽  
Taekyung Lee ◽  
Jiangfeng Song ◽  
Jonghyun Kim ◽  
Fusheng Pan
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Yield Strength ◽  
Creep Resistance ◽  
Room Temperature ◽  
High Thermal Stability ◽  
Long Period ◽  
Microstructures And Mechanical Properties

The microstructures and mechanical properties of the Mg88.5Zn5Y6.5-XREX (RE = Yb and Ce, X = 0, 1.5, 3.0, and 4.5) (wt.%) alloys were investigated in the present study. Mg88.5Zn5Y6.5 is composed of three phases, namely, α-Mg, long-period stacking ordered (LPSO) phases, and intermetallic compounds. The content of the LPSO phases decreased with the addition of Ce and Yb, and no LPSO phases were detected in Mg88.5Zn5Y2.0Yb4.5. The alloys containing the LPSO phases possessed a stratified microstructure and exhibited excellent mechanical properties. Mg88.5Zn5Y5.0Ce1.5 exhibited the highest creep resistance and mechanical strength at both room temperature and 200 °C, owing to its suitable microstructure and high thermal stability. The yield strength of Mg88.5Zn5Y5.0Ce1.5 at room temperature was 358 MPa. The ultimate tensile strength of Mg88.5Zn5Y5.0Ce1.5 at room temperature and 200 °C was 453 MPa and 360 MPa, respectively.

Effect of Small Iron, Chromium and Boron Additions as Alloying Elements on Microstructure and Mechanical Properties of Ni3Al

2007 ◽  
Vol 23 ◽  
pp. 123-126
Author(s):  
Radu L. Orban ◽  
Mariana Lucaci
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Room Temperature ◽  
Alloying Elements ◽  
Alloyed Powder ◽  
Mechanically Alloyed ◽  
Powder Mixtures ◽  
B Additions ◽  
Strength And Ductility ◽  
Iron Chromium

This paper investigates the effect of Fe, Cr and B additions, in small proportions, as alloying elements in Ni3Al with the purpose to reduce its intrinsic fragility and extrinsic embrittlement and to enhance, in the same time, its mechanical properties. It represents a development of some previous research works of the authors, proving that Ni3Al-Fe-Cr-B alloys obtained by reactive synthesis (SHS) starting from Mechanically Alloyed powder mixtures have superior both room temperature tensile strength and ductility, and compression ones at temperatures up to 800 °C, than pure Ni3Al. These create premises for their using as superalloys substitutes.

Processing of Nanoporous Gold by Dealloying and its Morphological Control

2007 ◽  
Vol 561-565 ◽  
pp. 1657-1660 ◽  
Author(s):  
Masataka Hakamada ◽  
Mamoru Mabuchi
Keyword(s):  
Mechanical Properties ◽  
Thermal Treatment ◽  
Acid Treatment ◽  
Nanoporous Gold ◽  
Anisotropic Structure ◽  
Ideal Strength ◽  
Pore Characteristics ◽  
Very High ◽  
Ligament Size ◽  
The Ideal

Nanoporous gold was fabricated by dealloying and their pore characteristics were further modified by thermal or acid treatment. The fabricated nanoporous gold had a ligament size of approximately 5 nm. Thermal treatment on the nanoporous gold increased the ligament size to approximately 500 nm. During the thermal treatment, ligaments are bonded across the cracks which had been generated during the dealloying. Acid treatment also increased the ligament size to approximately 500 nm; however, the acid treatment had a different effect on the pore characteristics from the thermal treatment. As a result, nanoporous gold prism microassembly with anisotropic structure was spontaneously fabricated by the acid treatment. The mechanical properties of nanoporous gold were also examined. It is estimated that the yield strength of nanosized ligaments in nanoporous gold is very high and close to the ideal strength of gold.

Test Methods for Mechanical Properties of Structural Adhesives

2010 ◽  
Vol 97-101 ◽  
pp. 814-817 ◽  
Author(s):  
Jun Deng
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Shear Strength ◽  
Elastic Modulus ◽  
Butt Joint ◽  
Test Methods ◽  
Joint Specimen ◽  
Lap Shear ◽  
Better Than

One of the greatest drawbacks to predicting the behaviour of bonded joints has been the lack of reliable data on the mechanical properties of adhesives. In this study, methods for determining mechanical properties of structural adhesive were discussed. The Young’s modulus, Poisson’s ratio and tensile strength of the adhesive were tested by dogbone specimens (bulk form) and butt joint specimens (in situ form). The shear modulus and shear strength were test by V-notched specimens (bulk form) and thick adherend lap-shear (TALS) joint specimens (in situ form). The test results show that the elastic modulus provided by the manufacturer is too low, the dogbone specimen is better than the butt joint specimen to test the tensile strength and elastic modulus and the TALS joint specimen is better than the V-notched specimen to test the shear strength.

Strength of Commercial Aluminum Alloys after Equal Channel Angular Pressing and Post-ECAP Processing

2006 ◽  
Vol 114 ◽  
pp. 91-96 ◽  
Author(s):  
Maxim Yu. Murashkin ◽  
M.V. Markushev ◽  
Julia Ivanisenko ◽  
Ruslan Valiev
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Aluminum Alloys ◽  
Ultimate Tensile Strength ◽  
Equal Channel Angular Pressing ◽  
Room Temperature ◽  
Solution Treatment ◽  
Ecap Processing ◽  
Angular Pressing

The effects of equal channel angular pressing (ECAP), further heat treatment and rolling on the structure and room temperature mechanical properties of the commercial aluminum alloys 6061 (Al-0.9Mg-0.7Si) and 1560 (Al-6.5Mg-0.6Mn) were investigated. It has been shown that the strength of the alloys after ECAP is higher than that achieved after conventional processing. Prior ECAP solution treatment and post-ECAP ageing can additionally increase the strength of the 6061 alloy. Under optimal ageing conditions a yield strength (YS) of 434 MPa and am ultimate tensile strength (UTS) of 470 MPa were obtained for the alloy. Additional cold rolling leads to a YS and UTS of 475 and 500 MPa with 8% elongation. It was found that the post-ECAP isothermal rolling of the 1560 alloy resulted in the formation of a nano-fibred structure and a tensile strength (YS = 540 MPa and UTS = 635 MPa) that has never previously been observed in commercial non-heat treatable alloys.

Investigation of Mechanical Properties of Nanostructured Titanium Processed by Warm ECAP Followed Cold Rolling

2014 ◽  
Vol 875-877 ◽  
pp. 63-67 ◽  
Author(s):  
Dinh van Hai ◽  
Nguyen Trong Giang
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Tensile Strength ◽  
Cold Rolling ◽  
Room Temperature ◽  
Pure Titanium ◽  
Rolling Process ◽  
Coarse Grain ◽  
Nanostructured Titanium

In this work, ECAP technique was combined with cold rolling process in order to enhance mechanical properties and microstructure of pure Titanium. Coarse grain (CG) Titanium with original grain size of 150 μm had been pressed by ECAP at 425oC by 4, 8 and 12 passes, respectively. This process then was followed by rolling at room temperature with 35%, 55%, and 75% rolling strains. After two steps, mechanical properties such as strength, hardness and microstructure of processed Titanium have been measured. The result indicated significant effect of cold rolling on tensile strength, hardness and microstructure of ECAP-Titanium.

Effects of Direct Thermal Method Processing Parameters on Mechanical Properties of Semisolid A6061 Feedstock

2021 ◽  
Vol 18 (1) ◽  
Author(s):  
M. F. M. Tajudin ◽  
A. H. Ahmad ◽  
M. M. Rashidi
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Room Temperature ◽  
Processing Parameters ◽  
Holding Time ◽  
Thermal Method ◽  
Pouring Temperature ◽  
Porosity Level ◽  
Experimental Works ◽  
Temperature Water

This paper highlights the effects of pouring temperature and holding time on the mechanical properties of aluminium 6061 semisolid feedstock billets. The semisolid metal feedstock billets were prepared by a direct thermal method (DTM), in which the molten metal was poured into a cylindrical copper mould with a different combination of pouring temperature and holding time before it was solidified in room temperature water. The results show that the sample with pouring temperature slightly above aluminium 6061 liquidus temperature has the lowest porosity, thereby the highest mechanical properties value. The sample with a pouring temperature of 660 °C and holding time of 60 s has the density, tensile strength and hardness properties of 2.701 g/cm3, 146.797 MPa, and 86.5 HV, respectively. Meanwhile, the sample at a pouring temperature of 640 °C and holding time of 20 s has density, tensile strength and hardness properties of 2.527 g/cm3, 65.39 MPa, and 71.79 HV, respectively. The density and fractography tests were conducted to confirm the existence of porosity within the samples. The results from these experimental works suggested that the mechanical properties of DTM semisolid feedstock billet merely depended on processing parameters, which influenced the porosity level within the feedstock billet, thus directly affected their mechanical properties.

Effect of Hot Processing on Mircrostructure and Properties of Flat Billets of TA15 Titanium Alloy

2021 ◽  
Vol 1016 ◽  
pp. 906-910
Author(s):  
Xin Hua Min ◽  
Cheng Jin
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Titanium Alloy ◽  
High Temperature ◽  
Room Temperature ◽  
High Strength ◽  
Slow Cooling ◽  
Microstructure And Mechanical Properties ◽  
Ta15 Titanium Alloy ◽  
The Ideal

In this paper,effect of the different forging processes on the microstructure and mechanical properties of the flat flat billets of TA15 titanium alloy was investigated.The flat billiets of 80 mm×150 mm×L sizes of TA15 titanium alloy are produced by four different forging processes.Then the different microstrure and properties of the flat billiets were obtained by heat treatment of 800 °C~850 °C×1 h~4h.The results show that, adopting the first forging temperature at T1 °C、slow cooling and the second forging temperature at T2°C 、quick cooling, the primary αphases content is just 10%, and there are lots of thin aciculate phases on the base. This microstructure has both high strength at room temperature and high temperature, while the properties between the cross and lengthwise directions are just the same. So the hot processing of the first forging temperature at T1 °C、slow cooling and the second forging temperature at T2°C 、quick cooling is choosed as the ideal processing for production of aircraft frame parts.

Fabrication and investigation on the properties of ilmenite (FeTiO3)-based Al composite by accumulative roll bonding

2019 ◽  
Vol 54 (10) ◽  
pp. 1259-1271 ◽  
Author(s):  
Medhat Elwan ◽  
A Fathy ◽  
A Wagih ◽  
A R S Essa ◽  
A Abu-Oqail ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Accumulative Roll Bonding ◽  
Room Temperature ◽  
Volume Fraction ◽  
Raw Material ◽  
Accumulative Roll Bonding Process ◽  
Roll Bonding ◽  
Hardness Tests ◽  
Al Composite

In the present study, the aluminum (Al) 1050–FeTiO3 composite was fabricated through accumulative roll bonding process, and the resultant mechanical properties were evaluated at different deformation cycles at ambient temperature. The effect of the addition of FeTiO3 particle on the microstructural evolution and mechanical properties of the composite during accumulative roll bonding was investigated. The Al–2, 4, and 8 vol.% FeTiO3 composites were produced by accumulative roll bonding at room temperature. The results showed improvement in the dispersions of the particles with the increase in the number of the rolling cycles. In order to study the mechanical properties, tensile and hardness tests were applied. It was observed that hardness and tensile strength improve with increasing accumulative roll bonding cycles. The microhardness and tensile strength of the final composites are significantly improved as compared to those of original raw material Al 1050 and increase with increasing volume fraction of FeTiO3, reaching a maximum of ∼75 HV and ∼169 MPa for Al–8 vol.% FeTiO3 at seventh cycle, respectively.

Sign in / Sign up

Export Citation Format

Share Document