Glass Transition of LDPE and PP under High Quasi-Hydrostatic Pressure in Room Temperature

2021 ◽  
Author(s):  
Chaohu Yu ◽  
Yewen Zhang ◽  
Jingxian Xu ◽  
Yabo Sun ◽  
Zhi Li ◽  
...  
Keyword(s):  
Glass Transition ◽  
Hydrostatic Pressure ◽  
Room Temperature

Survival of mouse blastocysts after low-temperature preservation under high pressure

2004 ◽  
Vol 52 (4) ◽  
pp. 479-487 ◽  
Author(s):  
Cs. Pribenszky ◽  
M. Molnár ◽  
S. Cseh ◽  
L. Solti
Keyword(s):  
Phase Transition ◽  
Hydrostatic Pressure ◽  
Low Temperature ◽  
High Hydrostatic Pressure ◽  
Room Temperature ◽  
Freezing Point ◽  
Significant Loss ◽  
Embryo Cryopreservation ◽  
Subzero Temperatures ◽  
Survival Capacity

Cryoinjuries are almost inevitable during the freezing of embryos. The present study examines the possibility of using high hydrostatic pressure to reduce substantially the freezing point of the embryo-holding solution, in order to preserve embryos at subzero temperatures, thus avoiding all the disadvantages of freezing. The pressure of 210 MPa lowers the phase transition temperature of water to -21°C. According to the results of this study, embryos can survive in high hydrostatic pressure environment at room temperature; the time embryos spend under pressure without significant loss in their survival could be lengthened by gradual decompression. Pressurisation at 0°C significantly reduced the survival capacity of the embryos; gradual decompression had no beneficial effect on survival at that stage. Based on the findings, the use of the phenomena is not applicable in this form, since pressure and low temperature together proved to be lethal to the embryos in these experiments. The application of hydrostatic pressure in embryo cryopreservation requires more detailed research, although the experience gained in this study can be applied usefully in different circumstances.

A Raman study of B203 through the liquid-glass transition range

1992 ◽  
Vol 02 ◽  
pp. C2-265-C2-270
Author(s):  
A. K. HASSAN ◽  
L. M. TORELL ◽  
L. BORJESSON
Keyword(s):  
Glass Transition ◽  
Correlation Length ◽  
Room Temperature ◽  
Vibrational Mode ◽  
Low Frequency ◽  
Boson Peak ◽  
Transition Range ◽  
Structural Correlation ◽  
Raman Study ◽  
Correlation Range

The low frequency Raman spectrum of B203 and the boroxol ring vibrational mode at 808 cm-1 have been studied from room temperature to 1273 K as the glass transforms to a melt. Both the low frequeney "boson" peak and the boroxol mode are markedly influenced by the glass transition. Raising the temperature above Tg the strength of the 808 cm-1 mode decreases linearly indicating the Similar behavior of the boroxol ring concentration. The boson peak shows a different temperature behavior, which mirrors that of the sound velo city. The structural correlation length demostrates the same correlation range in the liquid and the glass. The results, when compared with neutron diffraction measurements contradict a recently proposed relation between the "boson correlation length" and the position of the first sharp diffraction peak of the structure factor.

Silk Polymer Coating with Low Dielectric Constant and High Thermal Stability for Ulsi Interlayer Dielectric

1997 ◽  
Vol 476 ◽  
Author(s):  
P. H. Townsend ◽  
S. J. Martin ◽  
J. Godschalx ◽  
D. R. Romer ◽  
D. W. Smith ◽  
...  
Keyword(s):  
Thin Film ◽  
Dielectric Constant ◽  
Glass Transition ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Integrated Circuits ◽  
Room Temperature ◽  
Polymer Network ◽  
Flow Characteristics ◽  
Interlayer Dielectric

AbstractA novel polymer has been developed for use as a thin film dielectric in the interconnect structure of high density integrated circuits. The coating is applied to the substrate as an oligomeric solution, SiLK*, using conventional spin coating equipment and produces highly uniform films after curing at 400 °C to 450 °C. The oligomeric solution, with a viscosity of ca. 30 cPs, is readily handled on standard thin film coating equipment. Polymerization does not require a catalyst. There is no water evolved during the polymerization. The resulting polymer network is an aromatic hydrocarbon with an isotropie structure and contains no fluorine.The properties of the cured films are designed to permit integration with current ILD processes. In particular, the rate of weight-loss during isothermal exposures at 450 °C is ca. 0.7 wt.%/hour. The dielectric constant of cured SiLK has been measured at 2.65. The refractive index in both the in-plane and out-of-plane directions is 1.63. The flow characteristics of SiLK lead to broad topographic planarization and permit the filling of gaps at least as narrow as 0.1 μm. The glass transition temperature for the fully cured film is greater than 490 °C. The coefficient of thermal expansivity is 66 ppm/°C below the glass transition temperature. The stress in fully cured films on Si wafers is ca. 60 MPa at room temperature. The fracture toughness measured on thin films is 0.62 MPa m ½. Thin coatings absorb less than 0.25 wt.% water when exposed to 80% relative humidity at room temperature.

scholarly journals Reprocessable, Reworkable, and Mechanochromic Polyhexahydrotriazine Thermoset with Multiple Stimulus Responsiveness

Polymers ◽  
2020 ◽  
Vol 12 (10) ◽  
pp. 2375
Author(s):  
Li Chen ◽  
Siyao Zhu ◽  
Innocent Toendepi ◽  
Qiuran Jiang ◽  
Yi Wei ◽  
...  
Keyword(s):  
Glass Transition ◽  
Room Temperature ◽  
Manufacturing Industries ◽  
Stimuli Responsive ◽  
Inorganic Acid ◽  
One Pot ◽  
Thermosetting Polymers ◽  
Multiple Stimulus ◽  
Damage Monitoring ◽  
Modern Manufacturing

Developing recyclable, reworkable, and intelligent thermosetting polymers, as a long-standing challenge, is highly desirable for modern manufacturing industries. Herein, we report a polyhexahydrotriazine thermoset (PHT) prepared by a one-pot polycondensation between 4-aminophenyl disulfide and paraformaldehyde. The PHT has a glass transition temperature of 135 °C and good solvent resistance. The incorporation of dual stimuli-responsive groups (disulfide bond and hexahydrotriazine ring) endows the PHT with re-processability, re-workability, and damage monitoring function. The PHT can be repeatedly reprocessed by hot pressing, and a near 100% recovery of flexural strength is achieved. The PHT can also degrade in inorganic acid or organic thiol solutions at room temperature. The thermally reworkable test demonstrates that, after heating the PHT at 200 °C for 1 h, the residuals can be easily wiped off. Finally, the PHT exhibits a reversible mechanochromic behavior when damaged.

Effect of high pressure on various diffusion mechanisms in oxygen-deficient ReBa2Cu3O7−x (Re = Y, Ho) single crystals

2019 ◽  
Vol 33 (04) ◽  
pp. 1950039
Author(s):  
G. Ya. Khadzhai ◽  
N. R. Vovk ◽  
R. V. Vovk ◽  
I. L. Goulatis ◽  
O. V. Dobrovolskiy
Keyword(s):  
High Pressure ◽  
Electrical Resistivity ◽  
Hydrostatic Pressure ◽  
Single Crystals ◽  
High Hydrostatic Pressure ◽  
Room Temperature ◽  
Diffusion Mechanisms ◽  
Diffusion Coalescence

The effect of high hydrostatic pressure on the relaxation of the electrical resistivity at room temperature of oxygen-nonstoichiometric [Formula: see text] (Re = Y, Ho) single crystals is investigated. The application of hydrostatic pressure has been revealed to significantly intensify the process of diffusion coalescence in the oxygen subsystem. At the same time, the intensity of the redistribution of labile oxygen is significantly changed when yttrium is replaced by holmium.

The Effect of Thermal History on Porcelain Expansion Behavior

1989 ◽  
Vol 68 (9) ◽  
pp. 1313-1315 ◽  
Author(s):  
C.W. Fairhurst ◽  
D.T. Hashinger ◽  
S.W. Twiggs
Keyword(s):  
Thermal Expansion ◽  
Glass Transition ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Heating Rate ◽  
Room Temperature ◽  
Heating Rates ◽  
Thermal Expansion Data ◽  
Temperature Range ◽  
Expansion Behavior

Porcelain-fused-to-metal restorations are fired several hundred degrees above the glass-transition temperature and cooled rapidly through the glass-transition temperature range. Thermal expansion data from room temperature to above the glass-transition temperature range are important for the thermal expansion of the porcelain to be matched to the alloy. The effect of heating rate during measurement of thermal expansion was determined for NBS SRM 710 glass and four commercial opaque and body porcelain products. Thermal expansion data were obtained at heating rates of from 3 to 30°C/min after the porcelain was cooled at the same rate. By use of the Moynihan equation (where Tg systematically increases in temperature with an increase in cooling/heating rate), the glass-transition temperatures (Tg) derived from these data were shown to be related to the heating rate.

Study of Application of Thermal Infrared Camouflage Materials in the National Defense Engineering

2014 ◽  
Vol 651-653 ◽  
pp. 107-110
Author(s):  
Nai Yan Zhang ◽  
Jun Liu
Keyword(s):  
Differential Scanning Calorimetry ◽  
Glass Transition ◽  
Room Temperature ◽  
Polymer Network ◽  
Thermal Infrared ◽  
Interpenetrating Polymer Network ◽  
National Defense ◽  
Scanning Calorimetry ◽  
Response To Temperature ◽  
Infrared Camouflage

In this paper, a series of semi-interpenetrating polymer network materials based on poly ((2-dimethylamino) ethyl methacrylate)/poly (N, N-diethylacrylamide) (PDMAEMA/PDEA) were synthesized at room temperature. The influence of this additive on the property of resulting PDEA materials was investigated and characterized. The glass transition temperature (Tg) of the semi-IPN materials was observed by Differential Scanning Calorimetry (DSC). Compared to PDEA, the semi-IPN materials exhibited excellent mutative values in response to an alternation of the temperature, and showed fast swelling and deswelling rates in response to temperature change, which suggests that these materials have potential application as thermal infrared camouflage materials.

APPLICATION OF REED-VIBRATION MECHANICAL SPECTROSCOPY FOR LIQUIDS IN STUDYING LIQUID CRYSTALLIZATION

2013 ◽  
Vol 27 (21) ◽  
pp. 1350080 ◽  
Author(s):  
HENG-WEI ZHOU ◽  
LI-NA WANG ◽  
LI-LI ZHANG ◽  
YI-NENG HUANG
Keyword(s):  
Glass Transition ◽  
Room Temperature ◽  
Crystallization Process ◽  
Volume Fraction ◽  
Supercooled Liquid ◽  
Avrami Exponent ◽  
Dimethyl Phthalate ◽  
Mechanical Spectroscopy ◽  
Crystal Volume ◽  
Complex Young’S Modulus

By using the reed-vibration mechanical spectroscopy for liquids (RMS-L), we measured the complex Young's modulus of dimethyl phthalate (DP) during a cooling and heating circulation starting from room temperature at about 2 KHz. The results show that there is no crystallization in the cooling supercooled liquid (CSL) of DP, but a crystallization process in the heating supercooled liquid (HSL) after the reverse glass transition. Based on the measured modulus, crystal volume fraction (v) during the HSL crystallization was calculated. Moreover, the Avrami exponent (n) was obtained according to the JJMA equation and v data. In view of n versus temperature and v, the nucleation dynamics was analyzed, and especially, there has already existed saturate nuclei in DP HSL before the crystallization. Furthermore, the authors inferred that the nuclei are induced by the random frozen stress in the glass, but there is no nucleus in CSL. The above results indicated that RMS-L might provide a new way to measure and analyze the crystallization of liquids.

Sign in / Sign up

Export Citation Format

Share Document