Thermal Diffusivity of Dispersed Materials

1978 ◽  
Vol 100 (4) ◽  
pp. 720-724 ◽  
Author(s):  
T. Y. R. Lee ◽  
R. E. Taylor
Keyword(s):  
Thermal Conductivity ◽  
Thermal Diffusivity ◽  
Room Temperature ◽  
Volume Fraction ◽  
Transient State ◽  
Second Phase ◽  
Effective Thermal Diffusivity ◽  
Variable Dispersion ◽  
Flash Technique ◽  
Effective Diffusivities

Measurements have been made of the effective thermal diffusivity at room temperature of composites consisting of one phase randomly dispersed in a second phase. The method is based on the flash technique. Data are presented for four types of composites ranging in particle-to-matrix diffusivity ratios from 0.48 to 1137, in volume specific heat ratios 0.04 to 1.16, and in volume fraction of dispersed particle from zero up to 34 percent. The results show that the limitations of the concept of an effective thermal diffusivity are far beyond the situations to which it is currently applied in the transient state heat conduction problems. Values of effective diffusivities derived from values of the effective thermal conductivity calculated from the Bruggeman variable-dispersion equation are found to agree well with the measured diffusivity values.

Effects of microstructural evolution on the thermal conductivity of α–Al2O3 prepared from nano-size γ–Al2O3 powder

2000 ◽  
Vol 15 (3) ◽  
pp. 744-750 ◽  
Author(s):  
Eduardo J. Gonzalez ◽  
Grady White ◽  
Lanhua Wei
Keyword(s):  
Thermal Conductivity ◽  
Thermal Diffusivity ◽  
Microstructural Evolution ◽  
Vickers Hardness ◽  
Room Temperature ◽  
Volume Fraction ◽  
Al2o3 Powder ◽  
Α Al2o3 ◽  
Thermal Diffusivities ◽  
Nano Size

The thermal diffusivities (D) of porous α–Al2O3 specimens prepared from nano-size γ–Al2O3 powder and from conventional submicrometer-size alumina powders were measured at room temperature, and the thermal conductivity (κ) was calculated from D. Plots of κ versus the volume fraction of porosity (P) showed that the data from both sets of samples followed similar linear curves. Similarly, data of Vickers hardness versus P obtained from the same specimens also followed a single linear curve. The good correlation of thermal diffusivity with P suggests that grain boundaries have a lesser effect on thermal transport than porosity.

Simultaneous Measurement of the Effective Thermal Conductivity and Effective Thermal Diffusivity of Nanofluids

2008 ◽  
Author(s):  
S. M. Sohel Murshed ◽  
Kai Choong Leong ◽  
Chun Yang
Keyword(s):  
Thermal Conductivity ◽  
Thermal Diffusivity ◽  
Effective Thermal Conductivity ◽  
Simultaneous Measurement ◽  
Volume Fraction ◽  
Particle Volume Fraction ◽  
Maximum Increase ◽  
Effective Thermal Diffusivity ◽  
Thermal Diffusivities ◽  
Volumetric Loading

A transient double hot-wire technique was developed for precise and simultaneous measurement of the effective thermal conductivity and effective thermal diffusivity of nanofluids. The measured effective thermal conductivities and effective thermal diffusivities of nanofluids were found to be higher than those of base fluids and they increase significantly with increasing volume fraction of nanoparticles. The increments of the thermal diffusivities were found to be slightly larger compared to the thermal conductivity values. For example, at 5% volumetric loading of TiO2 nanoparticles of 15 nm and 10 × 40 nm in ethylene glycol, the maximum increase in effective thermal conductivity was found to be 17% and 20%, whereas the maximum increase in effective thermal diffusivity was 25% and 29%, respectively. Besides particle volume fraction, particle material, particle size and the nature of the base fluid were found to have influence on the effective thermal conductivity and diffusivity of nanofluids. Based on the calibration results obtained for the base fluids the measurement error was estimated to be within 1.2 to 2%.

Thermo-Physical Properties of Copper Matrix Composites Reinforced with 3D-SiC Network

2010 ◽  
Vol 150-151 ◽  
pp. 144-149
Author(s):  
Hong Wei Xing ◽  
Jin Song Zhang ◽  
Xiao Ming Cao
Keyword(s):  
Thermal Conductivity ◽  
Physical Properties ◽  
Room Temperature ◽  
Volume Fraction ◽  
Copper Matrix ◽  
High Thermal Stability ◽  
Matrix Composites ◽  
Copper Matrix Composites ◽  
Specific Heat Capacities ◽  
Thermo Physical Properties

Copper matrix composites reinforced with 3D-SiC network (15v% and 20v% SiC) were fabricated by squeezing copper alloy into 3D-SiC network preforms. The thermo-physical properties of the copper matrix composites were investigated. The specific heat capacities of the composites were about 0.39~0.50 J•g-1•K-1. The coefficients of thermal expansion (CTEs) of the composites were found to be lower than 6.9×10-6 -1 at Room Temperature. The composites exhibited high thermal stability for 3D-SiC network advent. The thermal conductivity of the composites was in the range of 50~80W•m−1•K−1. The thermo-physical properties of Cu matrix composites had a great relationship with the structures of 3D-SiC network preforms. The thermal conductivity of the composites decreased with an increase in the volume fraction of SiC or the structures of the limbs changing compacted, but the CTEs were not completely according this rule.

Thermal Diffusivity and Conductivity of La0.7Ca0.3-xSrxMnO3 (x=0 to 0.10)

2012 ◽  
Vol 501 ◽  
pp. 319-323
Author(s):  
Hasan A. Alwi ◽  
Lay S. Ewe ◽  
Zahari Ibrahim ◽  
Noor B. Ibrahim ◽  
Roslan Abd-Shukor
Keyword(s):  
Thermal Conductivity ◽  
Electrical Conductivity ◽  
Grain Size ◽  
Transition Temperature ◽  
Thermal Diffusivity ◽  
Electrical Properties ◽  
Room Temperature ◽  
Electronic Contribution ◽  
Insulator Metal Transition ◽  
Thermal And Electrical Properties

We report the room temperature thermal conductivity κ and thermal diffusivity α of polycrystalline La0.7Ca0.3-xSrxMnO3 for x = 0 to 0.1. The samples were prepared by heating at 1220 and 1320oC. The insulator-metal transition temperature, TIM and thermal diffusivity increased with Sr content. Phonon was the dominant contributor to thermal conductivity and the electronic contribution was less than 1%. Enhancement of electrical conductivity σ and thermal diffusivity for x ≥ 0.08 was observed in both series of samples. The grain size of the samples (28 to 46 µm) does not show any affect on the thermal and electrical properties.

Influence of Mesocarp Fibre Inclusion on Thermal Properties of Foamed Concrete

2021 ◽  
Vol 87 (1) ◽  
pp. 1-11
Author(s):  
Siti Shahirah Suhaili ◽  
Md Azree Othuman Mydin ◽  
Hanizam Awang
Keyword(s):  
Thermal Conductivity ◽  
Heat Capacity ◽  
Thermal Properties ◽  
Thermal Diffusivity ◽  
Specific Heat ◽  
Specific Heat Capacity ◽  
Volume Fraction ◽  
Thermal Constant ◽  
Volume Fractions ◽  
Foamed Concrete

The addition of mesocarp fibre as a bio-composite material in foamed concrete can be well used in building components to provide energy efficiency in the buildings if the fibre could also offer excellent thermal properties to the foamed concrete. It has practical significance as making it a suitable material for building that can reduce heat gain through the envelope into the building thus improved the internal thermal comfort. Hence, the aim of the present study is to investigate the influence of different volume fractions of mesocarp fibre on thermal properties of foamed concrete. The mesocarp fibre was prepared with 10, 20, 30, 40, 50 and 60% by volume fraction and then incorporated into the 600, 1200 and 1800 kg/m3 density of foamed concrete with constant cement-sand ratio of 1:1.5 and water-cement ratio of 0.45. Hot disk thermal constant analyser was used to attain the thermal conductivity, thermal diffusivity and specific heat capacity of foamed concrete of various volume fractions and densities. From the experimental results, it had shown that addition of mesocarp fibre of 10-40% by volume fraction resulting in low thermal conductivity and specific heat capacity and high the thermal diffusivity of foamed concrete with 600 and 1800 kg/m3 density compared to the control mix while the optimum amount of mesocarp fibre only limit up to 30% by volume fraction for 1200 kg/m3 density compared to control mix. The results demonstrated a very high correlation between thermal conductivity, thermal diffusivity and specific heat capacity which R2 value more than 90%.

scholarly journals Phonon hydrodynamics and ultrahigh–room-temperature thermal conductivity in thin graphite

Science ◽  
2020 ◽  
Vol 367 (6475) ◽  
pp. 309-312 ◽  
Author(s):  
Yo Machida ◽  
Nayuta Matsumoto ◽  
Takayuki Isono ◽  
Kamran Behnia
Keyword(s):  
Thermal Conductivity ◽  
Thermal Diffusivity ◽  
Wide Temperature Range ◽  
Room Temperature ◽  
Phonon Dispersion ◽  
High Conductivity ◽  
Temperature Range ◽  
A Value ◽  
Out Of Plane ◽  
Intimate Link

Allotropes of carbon, such as diamond and graphene, are among the best conductors of heat. We monitored the evolution of thermal conductivity in thin graphite as a function of temperature and thickness and found an intimate link between high conductivity, thickness, and phonon hydrodynamics. The room-temperature in-plane thermal conductivity of 8.5-micrometer-thick graphite was 4300 watts per meter-kelvin—a value well above that for diamond and slightly larger than in isotopically purified graphene. Warming enhances thermal diffusivity across a wide temperature range, supporting partially hydrodynamic phonon flow. The enhancement of thermal conductivity that we observed with decreasing thickness points to a correlation between the out-of-plane momentum of phonons and the fraction of momentum-relaxing collisions. We argue that this is due to the extreme phonon dispersion anisotropy in graphite.

Effect of timeliness on the thermal properties of paraffin-based Al2O3 nanofluids

2019 ◽  
Vol 33 (05) ◽  
pp. 1950051
Author(s):  
Yangyang Wu ◽  
Baichao Wang ◽  
Dong Li ◽  
Changyu Liu
Keyword(s):  
Thermal Conductivity ◽  
Heat Capacity ◽  
Thermal Diffusivity ◽  
Specific Heat ◽  
Volume Concentration ◽  
Volume Fraction ◽  
Thermal Conversion ◽  
Volumetric Heat Capacity ◽  
Energy Storage Material ◽  
Over Time

Paraffin is an excellent photo-thermal conversion phase change energy storage material, and extensively used in the thermal storage field at the medium-low temperature. However, the low thermal conductivity of paraffin restricts its application in practice. Adding nanoparticles into paraffin is one of the effective methods to improve its thermal conductivity. Nevertheless, the thermal diffusivity, specific heat and volumetric heat capacity of paraffin as well as timeliness were affected after the addition of nanoparticles. In this paper, the influences of volume fraction of Al2O3 nanoparticle and timeliness on these thermal parameters of paraffin were investigated. The results show that the thermal conductivity of paraffin-based Al2O3 nanofluids increases first and then decreases with time, and the maximum thermal conductivity is 0.34 W/[Formula: see text] for volume fraction 1% on third day. The higher volume concentration, the lower specific heat and volumetric heat capacity, all present downtrend over time, until stable in the range of 0.3 MJ/[Formula: see text] and 0.4 MJ/[Formula: see text]. The average enhancement rate of specific heat and volumetric heat capacity are concentrates on −6% to 9%, −10% to 0%, respectively. While increasing the volume concentration, the thermal diffusivity has no obvious regularity, and presents undulatory property over time.

Heat transfer across sheared suspensions: role of the shear-induced diffusion

2013 ◽  
Vol 724 ◽  
pp. 527-552 ◽  
Author(s):  
Bloen Metzger ◽  
Ouamar Rahli ◽  
Xiaolong Yin
Keyword(s):  
Thermal Diffusivity ◽  
Volume Fraction ◽  
Spherical Particles ◽  
Transient Temperature ◽  
Particle Diffusion ◽  
Driving Mechanism ◽  
Average Particle ◽  
Particle Rotation ◽  
Effective Thermal Diffusivity ◽  
Couette Cell

AbstractSuspensions of non-Brownian spherical particles undergoing shear provide a unique system where mixing occurs spontaneously at low Reynolds numbers. Through a combination of experiments and simulations, we investigate the effect of shear-induced particle diffusion on the transfer of heat across suspensions. The influence of particle size, particle volume fraction and applied shear are examined. By applying a heat pulse to the inner copper wall of a Couette cell and analysing its transient temperature decay, the effective thermal diffusivity of the suspension, $\alpha $, is obtained. Using index matching and laser-induced fluorescence imaging, we measured individual particle trajectories and calculated their diffusion coefficients. Simulations that combined a lattice Boltzmann technique to solve for the flow and a passive Brownian tracer algorithm to solve for the transfer of heat are in very good agreement with experiments. Fluctuations induced by the presence of particles within the fluid cause a significant enhancement (${\gt }200\hspace{0.167em} \% $) of the suspension transport properties. The effective thermal diffusivity was found to be linear with respect to both the Péclet number ($\mathit{Pe}= \dot {\gamma } {d}^{2} / {\alpha }_{0} \leq 100$) and the solid volume fraction ($\phi \leq 40\hspace{0.167em} \% $), leading to a simple correlation $\alpha / {\alpha }_{0} = 1+ \beta \phi \mathit{Pe}$ where $\beta = 0. 046$ and ${\alpha }_{0} $ is the thermal diffusivity of the suspension at rest. In our Couette cell, the enhancement was found to be optimum for a volume fraction, $\phi \approx 40\hspace{0.167em} \% $, above which, due to steric effects, both the particle diffusion motion and of the effective thermal diffusion dramatically decrease. No such correlation was found between the average particle rotation and the thermal diffusivity of the suspension, suggesting that the driving mechanism for enhanced transport is the translational particle diffusivity. Movies are available with the online version of the paper.

Ultra-Fine Grained Al-SiC Metal Matrix Composite by Rotary Swaging Process

2011 ◽  
Vol 702-703 ◽  
pp. 320-323 ◽  
Author(s):  
Sivaswamy Giribaskar ◽  
Gouthama ◽  
Rajesh Prasad
Keyword(s):  
Metal Matrix Composite ◽  
Matrix Composite ◽  
Metal Matrix ◽  
Room Temperature ◽  
Volume Fraction ◽  
Second Phase ◽  
Fine Grained ◽  
Rotary Swaging ◽  
Sic Particles ◽  
Dynamic Recrystallisation

In present study microstructural evolution during swaging on aluminium alloy based metal matrix composite (MMC) reinforced with 15% volume fraction silicon carbide (SiC) particles is presented. Samples were swaged at room temperature in steps with reducing die dimensions using rotary swaging technique. SEM and TEM are used to study the microstructural characteristics of swaged samples. SEM observations were made to understand the flow and deformation characteristics of deforming aluminium matrix in the presence of second phase and reinforced SiC particles during swaging. TEM observations on swaged samples confirmed the formation of ultra-fine grains in Al-15%SiC MMC. It is shown that the dynamic recrystallisation occurring in the proximities of second phase particles during the deformation at room temperature, leads to very fine grained microstructure.

Sign in / Sign up

Export Citation Format

Share Document