On-Design and Off-Design Performance Analysis of a Gas Turbine Combined Cycle Using the Exergy Method

2000 ◽  
Author(s):  
Alcides Codeceira Neto ◽  
Pericles Pilidis
Keyword(s):  
Natural Gas ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Exergy Analysis ◽  
Pressure Ratio ◽  
Calorific Value ◽  
Combined Cycle ◽  
Exergy Destruction ◽  
Turbine Engine ◽  
Design Point

The present paper describes an on-design and an off-design performance study of gas turbine combined cycle based power plants. The exergy analysis has been carried out along with the performance assessment, considering the overall plant exergetic efficiency and the exergy destruction in the various components of the plant. The exergy method highlights irreversibility within the plant components, and it is of particular interest in this investigation. A computational analysis has been carried out to investigate the effects of compressor pressure ratio and gas turbine entry temperature on the thermodynamic performance of combined gas / steam power cycles. The exergy analysis has been performed for on-design point calculations, considering single shaft gas turbines with different compressor pressure ratios and turbine entry temperatures. Nearly 100 MW shaft power gas turbine engines burning natural gas fuel have been selected in this study. The off-design calculations have been performed for one of the gas turbines selected from the on-design point studies. For this particular gas turbine engine, fuel has been changed from natural gas to a low calorific value fuel gas originated from the gasification of wood. The exergy analysis indicates that maximum exergy is destroyed in the combustor, in the case of combined gas / steam cycles burning natural gas. For these studies on-design point, the exergy destruction in the combustor is found to decrease with increasing compressor pressure ratio to an optimum value and with increasing turbine entry temperature. In the off-design case the gas turbine engine is burning low calorific value fuel originated from the gasification of wood. The maximum exergy destruction occurs in the gasification process, followed by the combustion process in the gas turbine.

Exergy Analysis of Gas-Turbine Combined Cycle With CO2 Capture Using Pre-Combustion Decarbonization of Natural Gas

2002 ◽  
Author(s):  
Hanne M. Kvamsdal ◽  
Ivar S. Ertesva˚g ◽  
Olav Bolland ◽  
Tor Tolstad
Keyword(s):  
Natural Gas ◽  
Electric Power ◽  
Gas Turbine ◽  
Co2 Capture ◽  
Exergy Analysis ◽  
Pressure Ratio ◽  
Power Production ◽  
Combined Cycle ◽  
Electric Power Production ◽  
Chemical Exergy

A concept for natural-gas fired power plants with CO2 capture has been investigated using exergy analysis. The present approach involves decarbonization of the natural gas by authothermal reforming prior to combustion, producing a hydrogen-rich fuel. An important aspect of this type of process is the integration between the combined cycle and the reforming process. The net electric power production was 47.7% of the Lower Heating Value (LHV) or 45.8% of the chemical exergy of the supplied natural-gas. In addition, the chemical exergy of the captured CO2 and the compression of this CO2 to 80 bar represented 2.1% and 2.7%, respectively, of the natural-gas chemical exergy. For a corresponding conventional combined cycle without CO2 capture, the net electric power production was 58.4% of the LHV or 56.1% of the fuel chemical exergy. A detailed breakdown of irreversibility is presented. In the decarbonized natural-gas power plant, the effect of varying supplementary firing (SF) for reformer-feed preheating was investigated. This showed that SF increased the total irreversibility and decreased the net output of the plant. Next, the effects of increased gas-turbine inlet temperature and of gas-turbine pressure ratio were studied. For the conventional plant, higher pressure led to increased efficiency for some cases. In the decarbonized natural-gas process, however, higher pressure ratio led to higher irreversibility and reduced thermal-plant efficiency.

Efficiency Analysis of Gas Turbine Combined-Cycle Fed with Synthetic Natural Gas (SNG) and Mixture of Syngas and SNG

2015 ◽  
Vol 656-657 ◽  
pp. 113-118
Author(s):  
Hsiu Mei Chiu ◽  
Po Chuang Chen ◽  
Yau Pin Chyou ◽  
Ting Wang
Keyword(s):  
Natural Gas ◽  
Simulation Model ◽  
Steam Turbine ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Combined Cycle ◽  
System Level ◽  
Minimum Requirement ◽  
Synthetic Natural Gas ◽  
System Level Simulation

The effect of synthetic natural gas (SNG) and mixture of syngas and SNG fed to Natural Gas Combined-Cycle (NGCC) plants is presented in this study via a system-level simulation model. The commercial chemical process simulator, Pro/II®V8.1.1, was used in the study to build the analysis model. The NGCC plant consists of gas turbine (GT), heat recovery steam generator (HRSG) and steam turbine (ST). The study envisages two analyses as the basic and feasibility cases. The former is the benchmark case which is verified by the reference data with the GE 7FB gas turbine. According to vendor’s specification, the typical net plant efficiency of GE 7FB NGCC with two gas turbines to one steam turbine is 57.5% (LHV), and the efficiency is the benchmark in the simulation model built in the study. The latter introduces a feasibility study with actual parameters in Taiwan. The SNG-fed GE 7FB based combined-cycle is evaluated, and the mixture of SNG and syngas is also evaluated to compare the difference of overall performance between the two cases. The maximum ratio of syngas to SNG is 0.14 due to the constraint for keeping the composition of methane at a value of 80 mol%, to meet the minimum requirement of NG in Taiwan. The results show that the efficiency in either case of SNG or mixture of SNG and syngas is slightly lower than the counterpart in the benchmark one. Because the price of natural gas is much higher than that of coal, it results in higher idle capacity of NGCC. The advantage of adopting SNG in Taiwan is that it could increase the capacity factor of combined-cycles in Taiwan. The study shows a possible way to use coal and reduce the CO2emission, since coal provides nearly half of the electricity generation in Taiwan in recent years.

Evolution and Future Trend of Large Frame Gas Turbines: A New 1600 Degree C, J Class Gas Turbine

2012 ◽  
Author(s):  
Satoshi Hada ◽  
Masanori Yuri ◽  
Junichiro Masada ◽  
Eisaku Ito ◽  
Keizo Tsukagoshi
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Pressure Ratio ◽  
Standard Condition ◽  
Development Program ◽  
Combined Cycle ◽  
Component Technology ◽  
Extensive Experience ◽  
National Project ◽  
Cycle Efficiency

MHI recently developed a 1600°C class J-type gas turbine, utilizing some of the technologies developed in the National Project to promote the development of component technology for the next generation 1700°C class gas turbine. This new frame is expected to achieve higher combined cycle efficiency and will contribute to reduce CO2 emissions. The target combined cycle efficiency of the J type gas turbine will be above 61.5% (gross, ISO standard condition, LHV) and the 1on1 combined cycle output will reach 460MW for 60Hz engine and 670MW for 50Hz engine. This new engine incorporates: 1) A high pressure ratio compressor based on the advanced M501H compressor, which was verified during the M501H development in 1999 and 2001. 2) Steam cooled combustor, which has accumulated extensive experience in the MHI G engine (> 1,356,000 actual operating hours). 3) State-of-art turbine designs developed through the 1700°C gas turbine component technology development program in Japanese National Project for high temperature components. This paper discusses the technical features and the updated status of the J-type gas turbine, especially the operating condition of the J-type gas turbine in the MHI demonstration plant, T-Point. The trial operation of the first M501J gas turbine was started at T-point in February 2011 on schedule, and major milestones of the trial operation have been met. After the trial operation, the first commercial operation has taken place as scheduled under a predominantly Daily-Start-and-Stop (DSS) mode. Afterward, MHI performed the major inspection in October 2011 in order to check the mechanical condition, and confirmed that the hot parts and other parts were in sound condition.

Off-Design Performance Investigation of a Low Calorific Value Gas Fired Generic-Type Single-Shaft Gas Turbine

2008 ◽  
Vol 130 (3) ◽  
Author(s):  
Raik C. Orbay ◽  
Magnus Genrup ◽  
Pontus Eriksson ◽  
Jens Klingmann
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Pressure Ratio ◽  
Calorific Value ◽  
Working Fluid ◽  
Inlet Temperature ◽  
Flammability Limits ◽  
Generic Type ◽  
Wobbe Index ◽  
The Impact

When low calorific value gases are fired, the performance and stability of gas turbines may deteriorate due to a large amount of inertballast and changes in working fluid properties. Since it is rather rare to have custom-built gas turbines for low lower heating value (LHV) operation, the engine will be forced to operate outside its design envelope. This, in turn, poses limitations to usable fuel choices. Typical restraints are decrease in Wobbe index and surge and flutter margins for turbomachinery. In this study, an advanced performance deck has been used to quantify the impact of firing low-LHV gases in a generic-type recuperated as well as unrecuperated gas turbine. A single-shaft gas turbine characterized by a compressor and an expander map is considered. Emphasis has been put on predicting the off-design behavior. The combustor is discussed and related to previous experiments that include investigation of flammability limits, Wobbe index, flame position, etc. The computations show that at constant turbine inlet temperature, the shaft power and the pressure ratio will increase; however, the surge margin will decrease. Possible design changes in the component level are also discussed. Aerodynamic issues (and necessary modifications) that can pose severe limitations on the gas turbine compressor and turbine sections are discussed. Typical methods for axial turbine capacity adjustment are presented and discussed.

Steam-Cooled Gas Turbine Casings, Struts, and Disks in a Reheat Gas Turbine Combined Cycle: Part I—Compressor and Combustor

1983 ◽  
Vol 105 (4) ◽  
pp. 844-850 ◽  
Author(s):  
I. G. Rice
Keyword(s):  
Steam Turbine ◽  
Gas Turbine ◽  
Gas Turbines ◽  
High Performance ◽  
Material Selection ◽  
Pressure Ratio ◽  
Industrial Applications ◽  
Combined Cycle ◽  
Tip Clearance ◽  
Turbine Output

High-cycle pressure-ratio (38–42) gas turbines being developed for future aircraft and, in turn, industrial applications impose more critical disk and casing cooling and thermal-expansion problems. Additional attention, therefore, is being focused on cooling and the proper selection of materials. Associated blade-tip clearance control of the high-pressure compressor and high-temperature turbine is critical for high performance. This paper relates to the use of extracted steam from a steam turbine as a coolant in a combined cycle to enhance material selection and to control expansion in such a manner that the cooling process increases combined-cycle efficiency, gas turbine output, and steam turbine output.

On the Economics of the Use of Biomass Fuels in Gas Turbine Cycles: Gasification vs. Externally Firing

2004 ◽  
Author(s):  
Sandro Barros Ferreira ◽  
Pericles Pilidis
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Power Plants ◽  
Technological Development ◽  
Pilot Scale ◽  
Combined Cycle ◽  
Point Of View ◽  
Turbine Engine ◽  
Current Technology ◽  
Integrated Gasification

The use of biomass as gas turbine combined cycle fuels is broadly seen as one of the alternatives to diminish greenhouse gas emissions, mainly CO2, due to the efficiency delivered by such systems and the renewable characteristic of biomass itself. Integrated gasification cycles, BIGGT, are the current technology available; however the gasification system severely penalizes the power plant in terms of efficiency and demands modifications in the engine to accommodate the large fuel mass flow. This gives an opportunity to improvements in the current technologies and implementation of new ones. This paper intends to analyze new alternatives to the use of solid fuels in gas turbines, from the economical point of view, through the use of external combustion, EFGT, discussing its advantages and limitations over the current technology. The results show that both EFGT and BIGGT technologies are economically competitive with the current natural gas fired gas turbines. However, BIGGT power plants are still in pilot scale and the EFGT plants need further technological development. Thermodynamically speaking, the inherently recuperative characteristic of the EFGT gas turbine engine makes it well suited to the biomass market. The thermal efficiency of this cycle is higher than the BIGGT system. Furthermore, its fuel flexibility and negligible pre-treatmet is another advantage that makes it an interesting option for the Brazilian market.

Performance and Cost Analysis of Advanced Gas Turbine Cycles With Precombustion CO2 Capture

2008 ◽  
Vol 131 (2) ◽  
Author(s):  
Stéphanie Hoffmann ◽  
Michael Bartlett ◽  
Matthias Finkenrath ◽  
Andrei Evulet ◽  
Tord Peter Ursin
Keyword(s):  
High Pressure ◽  
Power Plant ◽  
Natural Gas ◽  
Gas Turbine ◽  
Co2 Capture ◽  
Gas Turbines ◽  
High Efficiency ◽  
Combined Cycle ◽  
Co2 Separation ◽  
The Cost

This paper presents the results of an evaluation of advanced combined cycle gas turbine plants with precombustion capture of CO2 from natural gas. In particular, the designs are carried out with the objectives of high efficiency, low capital cost, and low emissions of carbon dioxide to the atmosphere. The novel cycles introduced in this paper are comprised of a high-pressure syngas generation island, in which an air-blown partial oxidation reformer is used to generate syngas from natural gas, and a power island, in which a CO2-lean syngas is burnt in a large frame machine. In order to reduce the efficiency penalty of natural gas reforming, a significant effort is spent evaluating and optimizing alternatives to recover the heat released during the process. CO2 is removed from the shifted syngas using either CO2 absorbing solvents or a CO2 membrane. CO2 separation membranes, in particular, have the potential for considerable cost or energy savings compared with conventional solvent-based separation and benefit from the high-pressure level of the syngas generation island. A feasibility analysis and a cycle performance evaluation are carried out for large frame gas turbines such as the 9FB. Both short-term and long-term solutions have been investigated. An analysis of the cost of CO2 avoided is presented, including an evaluation of the cost of modifying the combined cycle due to CO2 separation. The paper describes a power plant reaching the performance targets of 50% net cycle efficiency and 80% CO2 capture, as well as the cost target of 30$ per ton of CO2 avoided (2006 Q1 basis). This paper indicates a development path to this power plant that minimizes technical risks by incremental implementation of new technology.

Application of “H Gas Turbine” Design Technology to Increase Thermal Efficiency and Output Capability of the Mitsubishi M701G2 Gas Turbine

2005 ◽  
Vol 127 (2) ◽  
pp. 369-374 ◽  
Author(s):  
Y. Fukuizumi ◽  
J. Masada ◽  
V. Kallianpur ◽  
Y. Iwasaki
Keyword(s):  
Gas Turbine ◽  
Thermal Efficiency ◽  
Gas Turbines ◽  
Pressure Ratio ◽  
Turbine Blades ◽  
Combined Cycle ◽  
Load Test ◽  
Air Cooling ◽  
Load Testing ◽  
Design Development

Mitsubishi completed design development and verification load testing of a steam-cooled M501H gas turbine at a combined cycle power plant at Takasago, Japan in 2001. Several advanced technologies were specifically developed in addition to the steam-cooled components consisting of the combustor, turbine blades, vanes, and the rotor. Some of the other key technologies consisted of an advanced compressor with a pressure ratio of 25:1, active clearance control, and advanced seal technology. Prior to the M501H, Mitsubishi introduced cooling-steam in “G series” gas turbines in 1997 to cool combustor liners. Recently, some of the advanced design technologies from the M501H gas turbine were applied to the G series gas turbine resulting in significant improvement in output and thermal efficiency. A noteworthy aspect of the technology transfer is that the upgraded G series M701G2 gas turbine has an almost equivalent output and thermal efficiency as H class gas turbines while continuing to rely on conventional air cooling of turbine blades and vanes, and time-proven materials from industrial gas turbine experience. In this paper we describe the key design features of the M701G2 gas turbine that make this possible such as the advanced 21:1 compressor with 14 stages, an advanced premix DLN combustor, etc., as well as shop load test results that were completed in 2002 at Mitsubishi’s in-house facility.

Next-Generation Integration Concepts for Air Separation Units and Gas Turbines

1997 ◽  
Vol 119 (2) ◽  
pp. 298-304 ◽  
Author(s):  
A. R. Smith ◽  
J. Klosek ◽  
D. W. Woodward
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Pressure Ratio ◽  
Elevated Pressure ◽  
Gas Production ◽  
Combined Cycle ◽  
Air Separation ◽  
Control Measures ◽  
Next Generation ◽  
Separation Unit

The commercialization of Integrated Gasification Combined Cycle (IGCC) Power has been aided by concepts involving the integration of a cryogenic air separation unit (ASU) with the gas turbine combined-cycle module. Other processes, such as coal-based ironmaking and combined power/industrial gas production facilities, can also benefit from the integration. It is known and now widely accepted that an ASU designed for “elevated pressure” service and optimally integrated with the gas turbine can increase overall IGCC power output, increase overall efficiency, and decrease the net cost of power generation when compared to nonintegrated facilities employing low-pressure ASUs. The specific gas turbine, gasification technology, NOx emission specification, and other site specific factors determine the optimal degree of compressed air and nitrogen stream integration. Continuing advancements in both air separation and gas turbine technologies offer new integration opportunities to improve performance and reduce costs. This paper reviews basic integration principles and describes next-generation concepts based on advanced high pressure ratio gas turbines, Humid Air Turbine (HAT) cycles and integration of compression heat and refrigeration sources from the ASU. Operability issues associated with integration are reviewed and control measures are described for the safe, efficient, and reliable operation of these facilities.

Dry, Low Emissions for the ‘H’ Heavy-Duty Industrial Gas Turbines: Full-Scale Combustion System Rig Test Results

2003 ◽  
Author(s):  
Geoff Myers ◽  
Dan Tegel ◽  
Markus Feigl ◽  
Fred Setzer ◽  
William Bechtel ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Pressure Ratio ◽  
Combined Cycle ◽  
Full Scale ◽  
Combustion System ◽  
Heavy Duty ◽  
Test Program ◽  
Industrial Gas Turbines ◽  
Inlet Conditions

The lean, premixed DLN2.5H combustion system was designed to deliver low NOx emissions from 50% to 100% load in both the Frame 7H (60 Hz) and Frame 9H (50 Hz) heavy-duty industrial gas turbines. The H machines employ steam cooling in the gas turbine, a 23:1 pressure ratio, and are fired at 1440 C (2600 F) to deliver over-all thermal efficiency for the combined-cycle system near 60%. The DLN2.5H combustor is a modular can-type design, with 14 identical chambers used on the 9H machine, and 12 used on the smaller 7H. On a 9H combined-cycle power plant, both the gas turbine and steam turbine are fired using the 14-chamber DLN2.5H combustion system. An extensive full-scale, full-pressure rig test program developed the fuel-staged dry, low emissions combustion system over a period of more than five years. Rig testing required test stand inlet conditions of over 50 kg/s at 500 C and 28 bar, while firing at up to 1440 C, to simulate combustor operation at base load. The combustion test rig simulated gas path geometry from the discharge of the annular tri-passage diffuser through the can-type combustion liner and transition piece, to the inlet of the first stage turbine nozzle. The present paper describes the combustion system, and reports emissions performance and operability results over the gas turbine load and ambient temperature operating range, as measured during the rig test program.

Sign in / Sign up

Export Citation Format

Share Document