Measurement of Local Convective Heat Transfer Coefficients With Temperature Oscillation IR Thermography and Radiant Heating

2005 ◽  
Author(s):  
S. Freund ◽  
S. Kabelac
Keyword(s):  
Numerical Model ◽  
Surface Temperature ◽  
Heat Conduction Problem ◽  
Temperature Response ◽  
Three Dimensions ◽  
Single Frequency ◽  
Phase Lag ◽  
Radiant Heating ◽  
Temperature Drift ◽  
Ir Camera

A method using temperature oscillations to measure local convection coefficients from the outside of a heat-transferring wall has been developed. This method is contact-free, employing radiant heating with a laser and an IR camera for surface temperature measurements. The numerical model extends previous research to three dimensions and allows for rapid evaluation of the convection coefficients distribution of sizable heat exchanger areas. The technique relies first on experimental data of the phase-lag of the surface temperature response to periodic heating, and second on a numerical model of the heat-transferring wall that computes the local convection coefficients from the processed data. The temperature data processing includes an algorithm for temperature drift compensation and Single Frequency Discrete Fourier Transformations. The inverse heat conduction problem of deriving a surface map of convection coefficients from the phase-lag data is solved with a new numerical approach based on a complex 3-D finite-difference method. To validate the experimental approach, measurements of the temperature response of a semi-infinite specimen were analyzed. The results obtained were within 1.6% agreement with the analytical solution. The numerical model was verified by comparison with data generated by the FEM program ANSYS. The results of preliminary experiments investigating the local Nusselt number of water entering a tube are in agreement with established correlations. Future applications of this method will involve an aerodynamic vortex generator in a wind tunnel and plate heat exchangers. Another possible application of the experimental method is non-destructive testing of materials known as Lock-In Thermography.

scholarly journals A numerical model and validation of phase change material integrated thermoelectric radiant cooling panel

2019 ◽  
Vol 111 ◽  
pp. 01001
Author(s):  
Hansol Lim ◽  
Hye-Jin Cho ◽  
Seong-Yong Cheon ◽  
Soo-Jin Lee ◽  
Jae-Weon Jeong
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Numerical Model ◽  
Surface Temperature ◽  
Phase Change ◽  
Transfer Coefficient ◽  
Phase Change Material ◽  
Overall Heat Transfer Coefficient ◽  
Radiant Cooling ◽  
Change Material

A phase change material based radiant cooling panel with thermoelectric module (PCM-TERCP) is proposed in this study. It consists of two aluminium panels, and phase change materials (PCMs) sandwiched between the two panels. Thermoelectric modules (TEMs) are attached to one of the aluminium panels, and heat sinks are attached to the top side of TEMs. PCM-TERCP is a thermal energy storage concept equipment, in which TEMs freeze the PCM during the night whose melting temperature is 16○C. Therefore, the radiant cooling panel can maintain a surface temperature of 16◦C without the operation of TEM during the day. Furthermore, it is necessary to design the PCM-TERCP in a way that it can maintain the panel surface temperature during the targeted operating time. Therefore, the numerical model was developed using finite difference method to evaluate the thermal behaviour of PCM-TERCP. Experiments were also conducted to validate the performance of the developed model. Using the developed model, the possible operation time was investigated to determine the overall heat transfer coefficient required between radiant cooling panel and TEM. Consequently, the results showed that a overall heat transfer coefficient of 394 W/m2K is required to maintain the surface temperature between 16○C to 18○C for a 3 hours operation.

scholarly journals Thermal Characteristics of Breast Surface Temperature in Healthy Women

2021 ◽  
Vol 18 (3) ◽  
pp. 1097
Author(s):  
Anna Lubkowska ◽  
Monika Chudecka
Keyword(s):  
Mammary Gland ◽  
Temperature Distribution ◽  
Surface Temperature ◽  
Thermal Characteristics ◽  
The Body ◽  
Imaging Method ◽  
Infrared Thermal Imaging ◽  
Ir Camera ◽  
Entire Area ◽  
Healthy Women

Thermography is widely used in the medical field, including in the detection of breast disorders. The aim of the research was to characterize the range of breast surface temperature values, taking into account the entire area of the mammary gland and, independently, the nipple, in healthy women. An additional aim was to assess the symmetry of the breast temperature distribution (using an IR camera) and the correlation of temperatures with the content of adipose tissue. Thermograms were made for the right and left breasts, each time delineating the area of the entire breast and a separate area of the nipple, chest, and abdomen. Analyzing the intergroup differences in temperature of selected body areas (Tmean), it was shown that, in all cases, they were significantly higher in younger women. Statistical analysis showed no significant differences between breast and nipple temperatures in relation to the body sides. The highest temperatures within the mammary gland were recorded for the nipple area. The use of the high-resolution digital infrared thermal imaging method in early and screening preventive diagnoses of changes in the mammary gland requires individual interpretation of the results, taking into account the assessment of the physiological pattern of temperature distribution in both breasts.

scholarly journals The relevance of mid-Holocene Arctic warming to the future

2019 ◽  
Vol 15 (4) ◽  
pp. 1375-1394 ◽  
Author(s):  
Masakazu Yoshimori ◽  
Marina Suzuki
Keyword(s):  
Surface Temperature ◽  
General Circulation ◽  
Temperature Response ◽  
Longwave Radiation ◽  
General Circulation Models ◽  
Cross Model ◽  
Arctic Warming ◽  
Temperature Changes ◽  
The Future ◽  
Arctic Climate Change

Abstract. There remain substantial uncertainties in future projections of Arctic climate change. There is a potential to constrain these uncertainties using a combination of paleoclimate simulations and proxy data, but such a constraint must be accompanied by physical understanding on the connection between past and future simulations. Here, we examine the relevance of an Arctic warming mechanism in the mid-Holocene (MH) to the future with emphasis on process understanding. We conducted a surface energy balance analysis on 10 atmosphere and ocean general circulation models under the MH and future Representative Concentration Pathway (RCP) 4.5 scenario forcings. It is found that many of the dominant processes that amplify Arctic warming over the ocean from late autumn to early winter are common between the two periods, despite the difference in the source of the forcing (insolation vs. greenhouse gases). The positive albedo feedback in summer results in an increase in oceanic heat release in the colder season when the atmospheric stratification is strong, and an increased greenhouse effect from clouds helps amplify the warming during the season with small insolation. The seasonal progress was elucidated by the decomposition of the factors associated with sea surface temperature, ice concentration, and ice surface temperature changes. We also quantified the contribution of individual components to the inter-model variance in the surface temperature changes. The downward clear-sky longwave radiation is one of major contributors to the model spread throughout the year. Other controlling terms for the model spread vary with the season, but they are similar between the MH and the future in each season. This result suggests that the MH Arctic change may not be analogous to the future in some seasons when the temperature response differs, but it is still useful to constrain the model spread in the future Arctic projection. The cross-model correlation suggests that the feedbacks in preceding seasons should not be overlooked when determining constraints, particularly summer sea ice cover for the constraint of autumn–winter surface temperature response.

Influence of Covering Layer on Surface Temperature of Floor Radiant Heating System

2012 ◽  
Vol 204-208 ◽  
pp. 4260-4263 ◽  
Author(s):  
Hai Qian Zhao ◽  
Zhong Hua Wang ◽  
Lan Shuang Zhang
Keyword(s):  
Heat Transfer ◽  
Surface Temperature ◽  
Heating System ◽  
Radiant Heating ◽  
Wooden Floor ◽  
Surface Temperature Distribution ◽  
Covering Layer ◽  
Floor Surface ◽  
Space Saving ◽  
Cover Material

Floor radiant heating system has many advantages, energy and space saving, for example. The radiant floor is the radiator of floor radiant heating system, and its thermal parameters influence surface temperature distribution and comfort. In this paper, mathematical model of heat exchange coil under floor was established, and boundary heat transfer conditions were given. Based on these, surface temperature of different covering layer was calculated. According to the results, using different covering layer, the floor surface temperature has a great difference. Using wooden floor as cover material, the floor surface temperature is more moderate and uniform.

Characterization of Fouled Flat Sheet Membranes by Infrared Thermography

2014 ◽  
Author(s):  
Kennethrex O. Ndukaife ◽  
George Agbai Nnanna
Keyword(s):  
Surface Temperature ◽  
Infrared Thermography ◽  
Spectral Power ◽  
Membrane Surface ◽  
Infrared Camera ◽  
Feed Solution ◽  
Feed Concentration ◽  
Ir Camera ◽  
Measure Surface Temperature

An Infrared thermography (IRT) technique for characterization of fouling on membrane surface has been developed. The emitted spectral power from the fouled membrane is a function of emissivity and surface morphology. In this work, a FLIR A320 IR camera was used to measure surface temperature and emissivity. The surface temperature and the corresponding emissivity value of various areas on the fouled membrane surface is measured by the infrared camera and recorded alongside its thermogram. Different fouling experiments were performed using different concentrations of aluminum oxide nanoparticle mixed with deionized water as feed solution (333 ppm, 1833 ppm and 3333 ppm) so as to investigate the effect of feed concentration on the degree of fouling and thus its effect on the emissivity values measured on the membrane surfaces. Surface plots in 3D and Line plots are obtained for the measured emissivity values and thickness of the fouling deposit on the membrane surface respectively. The results indicate that the IRT technique is sensitive to changes that occur on the membrane surface due to deposition of contaminants on the membrane surface and that emissivity is a function of temperature, surface roughness and thickness of the specimen under investigation.

A Comparison of Radiation Versus Convection Calibration of Thin-Film Heat Flux Gauges

1999 ◽  
Author(s):  
D. E. Smith ◽  
J. V. Bubb ◽  
O. Popp ◽  
T. E. Diller ◽  
Stephen J. Hevey
Keyword(s):  
Thin Film ◽  
Heat Flux ◽  
Surface Temperature ◽  
Temperature Response ◽  
Turbine Rotor ◽  
Separate Experiment ◽  
Measured Temperature ◽  
Conduction Model ◽  
Time Resolved ◽  
Turbine Rotor Blade

Abstract A transient, in-situ method was examined for calibrating thin-film heat flux gauges using experimental data generated from both convection and radiation tests. Also, a comparison is made between this transient method and the standard radiation substitution calibration technique. Six Vatell Corporation HFM-7 type heat flux gauges were mounted on the surface of a 2-D, first-stage turbine rotor blade. These gauges were subjected to radiation from a heat lamp and in a separate experiment to a convective heat flux generated by flow in a transonic cascade wind tunnel. A second set of convective tests were performed using jets of cooled air impinging on the surface of the gauges. Direct measurements were simultaneously taken of both the time-resolved heat flux and surface temperature on the blade. The heat flux input was used to predict a surface temperature response using a one-dimensional, semi-infinite conduction model into a substrate with known thermal properties. The sensitivities of the gauges were determined by correlating the semi-infinite predicted temperature response to the measured temperature response. A finite-difference code was used to model the penetration of the heat flux into the substrate in order to estimate the time for which the semi-infinite assumption was valid. The results from these tests showed that the gauges accurately record both the convection and radiation modes of heat transfer. The radiation and convection tests yielded gauge sensitivities which agreed to within ±11%.

Transient Thermal Response of the Media by Free Space Laser Heating in Heat Assisted Magnetic Recording

2016 ◽  
Author(s):  
Shaomin Xiong ◽  
Robert Smith ◽  
Na Wang ◽  
Dongbo Li ◽  
Erhard Schreck ◽  
...  
Keyword(s):  
Magnetic Recording ◽  
Heat Conduction Problem ◽  
Temperature Response ◽  
Thermal Response ◽  
Areal Density ◽  
Heat Assisted Magnetic Recording ◽  
Lumped Model ◽  
The Media ◽  
Transient Thermal ◽  
Transient Thermal Response

Heat assisted magnetic recording (HAMR) promises to deliver higher storage areal density than the current perpendicular magnetic recording (PMR) product. A laser is introduced to the HAMR system to heat the high coercively magnetic media above the Curie temperature (Tc) which is as high as 750 K in order to enable magnetic writing. The thermal response of the media becomes very critical for the success of the data writing process. In this paper, a new method is proposed to understand the transient thermal behavior of the HAMR media. The temperature response of the media is measured based on thermal erasure of the magnetically written signal. A lumped model is built to simplify the heat conduction problem to understand the transient thermal response. Finite element modeling (FEM) is implemented to simulate the transient thermal response of the media due to the laser pulse heating. The experimental and simulation results show fairly good agreement.

Optimization of the Case Depth of a Cylinder Made With 4340 Steel by a Control of the Laser Heat Treatment Parameters

2018 ◽  
Author(s):  
Rachid Fakir ◽  
Noureddine Barka ◽  
Jean Brousseau
Keyword(s):  
Heat Treatment ◽  
Numerical Model ◽  
Surface Temperature ◽  
Laser Power ◽  
Case Depth ◽  
Maximum Temperature ◽  
Laser Heat Treatment ◽  
Laser Heat ◽  
4340 Steel ◽  
Cylindrical Workpiece

This paper presents a numerical model able to control the temperature distribution along a 4340 steel cylinder heat-treated with Nd: YAG laser. The numerical model developed using the numerical finite element method, was based on a study of surface temperature variation and the adjustment of this temperature by a control of the heat treatment laser power. The proposed analytical approach was built gradually by (i) the development of a numerical model of laser heat treatment of the cylindrical workpiece, (ii) an analysis of the results of simulations and experimental tests, (iii) development of a laser power adjustment approach, and (iv) proposal of a laser power control predictor using neural networks. This approach was made possible by highlighting the influence of the fixed (non-variable) parameters of the laser heat treatment on the case depth, and has shown that it is possible by controlling the laser parameters to homogenize the distribution of the maximum temperature reached on the surface for a uniform case depth. The feasibility and effectiveness of the proposed approach leads to a reliable and accurate model able to guarantee a uniform surface temperature and a regular case depth for a cylindrical workpiece of a length of 50-mm and with a diameter of between 16-mm and 22-mm.

scholarly journals How Asian aerosols impact regional surface temperatures across the globe

2020 ◽  
Author(s):  
Joonas Merikanto ◽  
Kalle Nordling ◽  
Petri Räisänen ◽  
Jouni Räisänen ◽  
Declan O'Donnell ◽  
...  
Keyword(s):  
Surface Temperature ◽  
Temperature Effects ◽  
Energy Transport ◽  
Temperature Response ◽  
The Arctic ◽  
Anthropogenic Aerosols ◽  
Atmospheric Energy ◽  
Atmospheric Energy Transport ◽  
Temperature Responses ◽  
Global Surface

Abstract. South and East Asian anthropogenic aerosols mostly reside in an air mass extending from the Indian Ocean to the North Pacific. Yet the surface temperature effects of Asian aerosols spread across the whole globe. Here, we remove Asian anthropogenic aerosols from two independent climate models (ECHAM6.1 and NorESM1) using the same representation of aerosols via MACv2-SP (a simple plume implementation of the 2nd version of the Max Planck Institute Aerosol Climatology). We then robustly decompose the global distribution of surface temperature responses into contributions from atmospheric energy flux changes. We find that the horizontal atmospheric energy transport strongly moderates the surface temperature response over the regions where Asian aerosols reside. Atmospheric energy transport and changes in clear-sky longwave radiation redistribute the temperature effects efficiently across the Northern hemisphere, and to a lesser extent also over the Southern hemisphere. The model-mean global surface temperature response to Asian anthropogenic aerosol removal is 0.26 ± 0.04 °C (0.22 ± 0.03 for ECHAM6.1 and 0.30 ± 0.03 °C for NorESM1) of warming. Model-to-model differences in global surface temperature response mainly arise from differences in longwave cloud (0.01 ± 0.01 for ECHAM6.1 and 0.05 ± 0.01 °C for NorESM1) and shortwave cloud (0.03 ± 0.03 for ECHAM6.1 and 0.07 ± 0.02 °C for NorESM1) responses. The differences in cloud responses between the models also dominate the differences in regional temperature responses. In both models, the Northern hemispheric surface warming amplifies towards the Arctic, where the total temperature response is highly seasonal and weakest during the Arctic summer. We estimate that under a strong Asian aerosol mitigation policy tied with strong climate mitigation (Shared Socioeconomic Pathway 1-1.9) the Asian aerosol reductions can add around 8 years' worth of current day global warming during the next few decades.

Sign in / Sign up

Export Citation Format

Share Document