The Dynamics of a Small-Scale Portable Electronics Device Under Impact Stimuli

Author(s):  
Gerard A. Kelly ◽  
Jeff M. Punch ◽  
Suresh Goyal

The reliability of portable electronic devices is of critical importance due to the consumer boom in mobile telephony in recent years. Impact is a key driver of failure in portable electronics and, in current design practice, extensive testing is used in conjunction with finite element simulations to ensure product reliability under impact stimuli. Testing is time-consuming and expensive – both free-drop and constrained drop tests are usually applied – and simulation techniques are very computationally intensive. The response of portable electronic devices to impact is currently not well understood, and there is clear need for investigation into the range of acceleration levels experienced by a representative model of a portable electronic device on impact. In this paper, free-drop testing was carried out on test vehicles representative of a typical mobile phone in order to acquire acceleration data from impact events. Drop test vehicles from Nylon and aluminium were used to provide a means of comparison for diverse material properties. The primary conclusion was that the dynamics of each drop event were highly sensitive to the initial conditions of the drop test, which was evident from wide variances in the acceleration data.

Author(s):  
A. Bulusu ◽  
D. G. Walker

As electronic device dimensions shrink down to the nanoscale regime, quantum effects such as electron tunneling and quantum confinement become significant. Along with quantum effects, various scattering processes such as carrier-carrier and carrier-defect scattering will influence device performance. Many transport models are not mature enough to couple the thermal effects with electronic solutions at such small scales. Incorporation of strong scattering influences on the electron transport in most cases is extremely difficult and computationally intensive. In this paper, we study a simple model that allows for integration of electron-phonon scattering effects in a nanotransistor. An acoustic deformation potential based electron-phonon scattering model is used to incorporate scattering in the device. A 7.5% drop in channel current was observed for a scattering rate of 1013/sec while current flow dropped by 50% for higher scattering rates. The effective channel resistance due to scattering was found to increase by a factor of 1.3. The results are compared to the I-V characteristics obtained using the non-equilibrium Green’s function (NEGF) formalism and were found to match well. The effect of phase-breaking scattering was also studied using NEGF where a 25% decrease in channel current was obtained thus demonstrating the importance of including scattering effects with quantum transport.


Author(s):  
A. A. Korneev

The article presents the results of the study of the filament modes of electronic lamps and ensuring the rational temperature of the cathode. A brief description and comparative analysis of existing methods with the proposed author are given. The dependence diagrams obtained as a result of a real experiment are presented. A new method of rational control of the electric vacuum devices (EVP) filament mode is proposed, thereby increasing the reliability and increasing the durability of the EVP during operation in high-quality and expensive complex technical systems. According to the results of the study, a new specialized electronic device was developed, which allowed to smoothly regulate the supply of the filament voltage, thereby ensuring the rational control of the operation of the EVP. The technique and specialized electronic device are developed on the basis of modern scientific and technical achievements. This made it possible to increase the reliability and efficiency of the electronic control system for solving critical tasks. When implementing the developed device, the problem of import substitution was solved.


2015 ◽  
Vol 81 (5) ◽  
Author(s):  
Amit Seta ◽  
Pallavi Bhat ◽  
Kandaswamy Subramanian

Zeldovich’s stretch–twist–fold (STF) dynamo provided a breakthrough in conceptual understanding of fast dynamos, including the small-scale fluctuation dynamos. We study the evolution and saturation behaviour of two types of generalized Baker’s map dynamos, which have been used to model Zeldovich’s STF dynamo process. Using such maps allows one to analyse dynamos at much higher magnetic Reynolds numbers $\mathit{Re}_{M}$ as compared to direct numerical simulations. In the two-strip map dynamo there is constant constructive folding, while the four-strip map dynamo also allows the possibility of a destructive reversal of the field. Incorporating a diffusive step parametrized by $\mathit{Re}_{M}$ into the map, we find that the magnetic field $B(x)$ is amplified only above a critical $\mathit{Re}_{M}=R_{\mathit{crit}}\sim 4$ for both types of dynamos. The growing $B(x)$ approaches a shape-invariant eigenfunction independent of initial conditions, whose fine structure increases with increasing $\mathit{Re}_{M}$. Its power spectrum $M(k)$ displays sharp peaks reflecting the fractal nature of $B(x)$ above the diffusive scale. We explore the saturation of these dynamos in three ways: via a renormalized reduced effective $\mathit{Re}_{M}$ (case I) or due to a decrease in the efficiency of the field amplification by stretching, without changing the map (case IIa), or changing the map (case IIb), and a combination of both effects (case III). For case I, we show that $B(x)$ in the saturated state, for both types of maps, approaches the marginal eigenfunction, which is obtained for $\mathit{Re}_{M}=R_{\mathit{crit}}$ independent of the initial $\mathit{Re}_{M}=R_{M0}$. On the other hand, in case II, for the two-strip map, we show that $B(x)$ saturates, preserving the structure of the kinematic eigenfunction. Thus the energy is transferred to larger scales in case I but remains at the smallest resistive scales in case II, as can be seen from both $B(x)$ and $M(k)$. For the four-strip map, $B(x)$ oscillates with time, although with a structure similar to the kinematic eigenfunction. Interestingly, the saturated state in case III shows an intermediate behaviour, with $B(x)$ similar to the kinematic eigenfunction at an intermediate $\mathit{Re}_{M}=R_{\mathit{sat}}$, with $R_{M0}>R_{\mathit{sat}}>R_{\mathit{crit}}$. The $R_{\mathit{sat}}$ value is determined by the relative importance of the increased diffusion versus the reduced stretching. These saturation properties are akin to the range of possibilities that have been discussed in the context of fluctuation dynamos.


2021 ◽  
Vol 79 (6) ◽  
pp. 631-640
Author(s):  
Takaaki Tsunoda ◽  
Takeo Tsukamoto ◽  
Yoichi Ando ◽  
Yasuhiro Hamamoto ◽  
Yoichi Ikarashi ◽  
...  

Electronic devices such as medical instruments implanted in the human body and electronic control units installed in automobiles have a large impact on human life. The electronic circuits in these devices require highly reliable operation. Radiographic testing has recently been in strong demand as a nondestructive way to help ensure high reliability. Companies that use high-density micrometer-scale circuits or lithium-ion batteries require high speed and high magnification inspection of all parts. The authors have developed a new X-ray source supporting these requirements. The X-ray source has a sealed tube with a transmissive target on a diamond window that offers advantages over X-ray sources having a sealed tube with a reflective target. The X-ray source provides high-power-density X-ray with no anode degradation and a longer shelf life. In this paper, the authors will summarize X-ray source classification relevant to electronic device inspection and will detail X-ray source performance requirements and challenges. The paper will also elaborate on technologies employed in the X-ray source including tube design implementations for high-power-density X-ray, high resolution, and high magnification simultaneously; reduced system downtime for automated X-ray inspection; and reduced dosages utilizing quick X-ray on-and-off emission control for protection of sensitive electronic devices.


Author(s):  
Т.П. Сабгайда ◽  
А.Н. Эделева

Проанализирована смертность лиц старше трудоспособного возраста (женщины 55+ и мужчины 60+) в условиях пандемии COVID-19 для определения потенциальной возможности её предотвращения. Использовали информацию базы данных РФС-ЕМИАС Москвы за 2019, 2020 и 2021 гг. (за периоды до 15 июня). Сделано заключение, что на фоне более корректного учета причин смерти в 2021 г., связанных с инфицированием вирусом SARS-CoV-2, вклад психических расстройств и болезней эндокринной системы в структуру причин смерти лиц старше трудоспособного возраста без учета случаев смерти от COVID-19 превышает показатели 2019 г. Рост смертности от заболеваний этих классов в значительной степени является следствием экзогенного стресса, связанного с пандемией, изоляцией лиц 65 лет и старше в начале пандемии, снижением эффективности их медико-социальной поддержки. Недостатки в организации социальной помощи лицам старших возрастных групп, слабое внедрение новых информационных технологий и носимых электронных устройств в практическую работу здравоохранения, малые масштабы общественных инициатив в области социальной помощи привели к потерям населения, которые могли бы быть предотвращены в период пандемии. The mortality of people over working age (women 55+ and men 60+) was analyzed in the context of COVID-19 pandemic in order to determine the potential for its prevention. The information from the Moscow mortality database for 2019, 2020 and 2021 (up to June 15) was used. Against the background of more correct accounting of death causes associated with SARS-CoV-2 virus infection in 2021, the contributions of mental disorders and endocrine diseases to the structure of death causes (excluding deaths from COVID-19) for people over working age are more than in 2019. The increase in mortality from diseases of these classes is largely a consequence of exogenous stress associated with a pandemic, isolation of people older 64 years and a decrease in the effectiveness of medical care. It was concluded that indirect losses from COVID-19 include avoidable mortality of elderly caused by shortcomings in organization of social assistance for them, the weak introduction of new information technologies and wearable electronic devices into the practical work of health care, small scale of public initiatives in the field of social assistance.


EP Europace ◽  
2021 ◽  
Author(s):  
Sharath Kumar ◽  
Jason Davis ◽  
Bernard Thibault ◽  
Iqwal Mangat ◽  
Benoit Coutu ◽  
...  

Abstract Aims Cardiac implantable electronic devices with device advisories have the potential of device malfunction. Remote monitoring (RM) of devices has been suggested to allow the identification of abnormal device performance and permit early intervention. We sought to describe the outcomes of patients with and without RM in devices subject to the Abbott Premature Battery Depletion (PBD) advisory with data from a Canadian registry. Methods and results Patients with an Abbott device subject to the PBD advisory from nine implantable cardioverter defibrillator (ICD) implanting centres in Canada were included in the registry. The use of RM was identified from baseline and follow-up data in the registry. The primary outcome was detection of PBD and all-cause mortality. A total of 2666 patients were identified with a device subject to the advisory. In all, 1687 patients (63.2%) had RM at baseline. There were 487 deaths during follow-up. At a mean follow-up of 5.7 ± 0.7 years, mortality was higher in those without a remote monitor compared with RM at baseline (24.7% vs. 14.5%; P < 0.001). Pre-mature battery depletion was identified in 36 patients (2.1%) with RM vs. 7 (0.7%) without RM (P = 0.004). Time to battery replacement was significantly reduced in patients on RM (median 5 vs. 13 days, P = 0.001). Conclusion The use of RM in patients with ICD and cardiac resynchronization therapy under advisory improved detection of PBD, time to device replacement, and was associated with a reduction in all-cause mortality. The factors influencing the association with mortality are unknown and deserve further study.


Author(s):  
Patrick W. Wilkerson ◽  
Andrzej J. Przekwas ◽  
Chung-Lung Chen

Multiscale multiphysics simulations were performed to analyze wirebonds for power electronic devices. Modern power-electronic devices can be subjected to extreme electrical and thermal conditions. Fully coupled electro-thermo-mechanical simulations were performed utilizing CFDRC’s CFD-ACE+ multiphysics simulation software and scripting capabilities. Use of such integrated multiscale multiphysics simulation and design tools in the design process can cut cost, shorten product development cycle time, and result in optimal designs. The parametrically designed multiscale multiphysics simulations performed allowed for a streamlined parametric analysis of the electrical, thermal, and mechanical effects on the wirebond geometry, bonding sites and power electronic device geometry. Multiscale analysis allowed for full device thermo-mechanical analysis as well as detailed analysis of wirebond structures. The multiscale simulations were parametrically scripted allowing for parametric simulations of the device and wirebond geometry as well as all other simulation variables. Analysis of heat dissipation from heat generated in the power-electronic device and through Joule heating were analyzed. The multiphysics analysis allowed for investigation of the location and magnitude of stress concentrations in the wirebond and device. These stress concentrations are not only investigated for the deformed wirebond itself, but additionally at the wirebond bonding sites and contacts. Changes in the wirebond geometry and bonding geometry, easily changed through the parametrically designed simulation scripts, allows for investigation of various wirebond geometries and operating conditions.


2018 ◽  
Vol 51 (9-10) ◽  
pp. 1133-1160 ◽  
Author(s):  
Bin Jiang ◽  
Rose Schmillen ◽  
William C. Sullivan

Overuse of portable electronic devices depletes one’s attention capacity, a critical cognitive resource. Although contact with nature promotes attentional functioning, we do not know the extent to which exposure to nature and the use of electronic devices interact to promote or inhibit attentional functioning. In this study, 81 participants performed cognitive tasks and then were randomly assigned to one of four rest treatments: green settings with or without a laptop computer and barren settings with or without a laptop computer. Attention was measured three times. Analysis showed a significant effect for both setting and use of a laptop as well as a significant interaction between setting and laptop use. A further analysis controlling for time spent focused on the laptop screen produced similar results. The findings show that using an electronic device in green settings substantially counteracts the attention enhancement benefits of green spaces.


Author(s):  
Eddy Mantjoro

Abstract Goals to be achieved through this research are as follows: (1) the scientific explanation about the initial conditions of fishing effort in the area of ​​research in this area is South Minahasa; (2) To obtain information on the historical development of the fish processing industry in North Sulawesi and Minahasa south in particular; (3) To be informed of the obstacles and challenges faced by the fisheries sector investors, especially fish processing timber. This research focuses on one unit of the fish processing industry wooden fish processing plant, and then in the case study method is relevant. The case study method is expected that researchers can examine more detailed and focused on problems experienced by fish processing company. As a consequence the results can not be generalized as like which would otherwise require science. Unless some case studies on the same topic on other companies and the result is the same, the efforts generalizations can be made. However the results of the case study can paint a picture on the history, constraints and barriers to investment that occur in similar industries and other industries. The initial condition of fisheries business investment in South Minahasa in 1995 was still dominated by small-scale businesses, which is limited to household livelihoods of fishermen. How governance is still very traditional in terms of business objectives just to meet daily food needs. Wooden fish processing technology already existed and developed since the year 700 BC in Japan. In Indonesia, especially in North Sulawesi started introduced in 1927 by a Japanese man named Hara Ko. The new investment started in 1971 until now. Investment in fish processing faces many obstacles and challenges, namely (1) the limited market share, (2) Legal certainty is not guaranteed, (3) Investors from outside the region and abroad to invest by holding on minimal information about the culture and traditions of local communities (4 ) morale of local residents very traditional if not arguably worse. (5) The investment policy is supported by the local government level only at the Regent while Assiten level, down to the village more displays of terror and intimidation to investors. Keywords: fish factory, investment, history, constraints, obstacles Abstrak Tujuan yang ingin dicapai melalui penelitian ini ialah sebagai berikut: (1) Penjelasan ilmiah tentang kondisi awal usaha perikanan di wilayah penelitian dalam hal ini Daerah Minahasa Selatan. (2) Memperoleh informasi tentang sejarah perkembangan industri pengolahan ikan di Sulawesi Utara dan Minahasa selatan khususnya. (3) Mendapatkan informasi mengenai kendala dan tantangan yang dihadapi oleh investor bidang perikanan khususnya pengolahan ikan kayu. Penelitian ini berfokus pada satu unit industri pengolahan ikan yakni pabrik pengolahan ikan kayu, maka metode studi kasus di pandang relevan. Metode studi kasus diharapkan peneliti dapat mengkaji lebih rinci dan fokus pada masalah yang dialami oleh perusahan pengolahan ikan. Sebagai konsekwensinya hasil penelitian tidak dapat digeneralisir sebagai layaknya yang di syaratkan oleh ilmu pengetahuan. Kecuali beberapa studi kasus dengan topik yang sama pada perusahan lain dan hasilnya sama maka upaya generalisasi dapat dilakukan. Walau demikian hasil studi kasus dapat melukiskan gambaran mengenai sejarah, kendala dan hambatan investasi yang terjadi pada industri sejenis dan industri lainnya. Kondisi awal usaha perikanan di wilayah Minahasa selatan pada tahun 1995 ketika investasi pabrik pengolahan ikan kayu di mulai masih didominasi oleh usaha skala kecil, yaitu sebatas mata pencaharian rumah tangga nelayan. Cara kelola pun masih sangat tradisional dalam pengertian tujuan usaha hanya untuk memenuhi kebutuhan makanan harian. Teknologi pengolahan ikan kayu sudah ada dan berkembang sejak tahun 700 sebelum masehi di Jepang. Di Indonesia khususnya di Sulawesi Utara mulai di perkenalkan pada tahun 1927 oleh orang Jepang bernama Hara Ko. Investasi baru dimulai pada tahun 1971 hingga sekarang. Investasi bidang pengolahan ikan menghadapi banyak kendala dan tantangan, yaitu (1) keterbatasan pangsa pasar, (2) Kepastian hukum tidak terjamin, (3) Investor dari luar daerah dan luar negeri berinvestasi dengan berpegang pada informasi minim mengenai budaya dan tradisi masyarakat lokal (4) moral kerja penduduk lokal amat tradisional jika tidak boleh dikatakan buruk.(5) Kebijakan investasi ditunjang oleh pemerintah daerah hanya pada level Bupati sedangkan level assiten, ke bawah sampai kelurahan lebih banyak menampilkan teror dan intimidasi kepada investor. Kata Kunci : pabrik ikan, investasi, sejarah, kendala, hambatan


2021 ◽  
Author(s):  
◽  
Tabitha Gaylyn Kura McKenzie

<p>What are the effects of using mobile devices as part of teacher professional development focused on teaching and learning the Māori language for Māori immersion educational settings? Answers to this question are explored by researching the extent to which electronic devices could be an effective strategy to address the crisis of the continuing decline of the Māori language. Another issue explored in the research is whether learners make expected gains in language proficiency through the use of mobile devices in comparison to standard face-to-face methods of language instruction.  An indigenous framework, Hei Korowai, was used to guide the research and ensure the practices used were culturally appropriate, particularly when entering into and negotiating the research project with participants. Kaupapa Māori and Māori centred approaches were also drawn on to gather data from semi-structured interviews, observations of mobile device use, online questionnaires, and Māori language proficiency tests results. Fifty two participants in total took part in the research, 46 from a PLD programme that used mobile devices and 6 from a separate PLD programme that used mainly face-to-face instruction.  Electronic forms of second language acquisition could be advantageous for learners to access audio and video content on the move and at a time, pace and place convenient for them. The capacity to have literally a library’s worth of resources, functions and internet connectivity all in one tool and at the touch of a button could also be of particular significance to users. Conversely, participant attitudes about technology, varied needs for initial and on-going training in how to operate the electronic devices, and interaction preferences were challenges experienced with utilising the device as part of the language learning and teaching process. Videos viewed on the device could also be seen as one-way learning with a lack of spiritual connection and no opportunities for discussion about content, potentially causing road blocks for learners who need extra support.  Face-to-face instruction was a preferred method for participants and the physical presence of the teacher highly valued to allow the space to pose and answer questions and receive an immediate response, which is not possible when learning via videos on a mobile device. However, there was acknowledgement of the complementary nature and value of utilising the mobile device followed by face-to-face meetings.  Evidence suggests that Māori have been quick to adopt and adapt new technologies since the arrival of the early settlers to the shores of Aotearoa. Could technology be the panacea, the cure-all for the revitalisation of the Māori language, a tool that provides access to language, culture and identity to the multitudes? This research tests the hypotheses in the context of two items of modern technology, the iPod Touch® and the iPad®.  The limitations of the research include potential bias in interpretation given the researcher’s insider position, the relatively small scale of the project, and the absence of a widely accepted theoretical framework for mobile learning. Critical questions that still remain are the implications of promoting ‘one Māori language’ for a large-scale programme and the risks in doing so for the preservation of tribal dialect and community identity. This study has, however, begun the conversation about the use of mobile devices in Māori medium educational settings, and it may contribute to an understanding of how to design technologies, media, and interactions to support learning within these settings towards innovative practices.</p>


Sign in / Sign up

Export Citation Format

Share Document