Numerical Model of the Circulation in an Open Bay

1978 ◽  
Vol 35 (12) ◽  
pp. 1631-1635 ◽  
Author(s):  
Brian Petrie ◽  
Ken Drinkwater

An external alongshore current setting to the east and across the mouth is proposed as the driving mechanism for the measured clockwise circulation in St. Georges Bay, Nova Scotia. A barotropic numerical model of an open bay forced by an alongshore current was able to produce a clockwise gyre in the bay. The model current velocities were in good agreement with the data. The generation, size, and intensity of the gyre required low values of vertical viscosity relative to horizontal viscosity. Key words: numerical model, bay, gyre, circulation, barotropic, current, coastal

2010 ◽  
Vol 13 (3) ◽  
pp. 78-87
Author(s):  
Hoai Cong Huynh

The numerical model is developed consisting of a 1D flow model and the morphological model to simulate the erosion due to the water overtopping. The step method is applied to solve the water surface on the slope and the finite difference method of the modified Lax Scheme is applied for bed change equation. The Meyer-Peter and Muller formulae is used to determine the bed load transport rate. The model is calibrated and verified based on the data in experiment. It is found that the computed results and experiment data are good agreement.


Micromachines ◽  
2021 ◽  
Vol 12 (11) ◽  
pp. 1432
Author(s):  
Lev Zakhvatkin ◽  
Alex Schechter ◽  
Eilam Buri ◽  
Idit Avrahami

During aerial missions of fuel-cell (FC) powered drones, the option of FC edge cooling may improve FC performance and durability. Here we describe an edge cooling approach for fixed-wing FC-powered drones by removing FC heat using the ambient air during flight. A set of experiments in a wind tunnel and numerical simulations were performed to examine the efficiency of FC edge cooling at various flight altitudes and cruise speeds. The experiments were used to validate the numerical model and prove the feasibility of the proposed method. The first simulation duplicated the geometry of the experimental setup and boundary conditions. The calculated temperatures of the stack were in good agreement with those of the experiments (within ±2 °C error). After validation, numerical models of a drone’s fuselage in ambient air with different radiator locations and at different flight speeds (10–30 m/s) and altitudes (up to 5 km) were examined. It was concluded that onboard FC edge cooling by ambient air may be applicable for velocities higher than 10 m/s. Despite the low pressure, density, and Cp of air at high altitudes, heat removal is significantly increased with altitude at all power and velocity conditions due to lower air temperature.


2008 ◽  
Vol 88 (6) ◽  
pp. 1093-1094
Author(s):  
Y. A. Papadopoulos ◽  
K. B. McRae ◽  
D. Gehl ◽  
S. A. E. Fillmore

Bruce birdsfoot trefoil (Lotus corniculatus L.) is a 71-clone synthetic variety developed at the Nappan Research Farm, Agriculture and Agri-Food Canada, Nappan, Nova Scotia. Bruce was developed through two cycles of mass selection for plant vigour (top and root growth) and winterhardiness, and one cycle of mass selection for re-growth vigour under grazing. In Atlantic Canada, Bruce produced more forage than the check cultivar Leo during 3 post-seeding years. It was also superior in spring growth with high first-cut herbage yields. Key words: Birdsfoot trefoil, Lotus corniculatus, cultivar description


1979 ◽  
Vol 16 (3) ◽  
pp. 505-522 ◽  
Author(s):  
C. E. Keen

The subsidence histories of the Labrador and Nova Scotian rifted continental margins have been determined from biostratigraphic data for 11 deep exploratory wells off Nova Scotia, for five wells off Labrador, for three wells northeast of Newfoundland, and for one well off the northeast coast of the United States of America. The components of subsidence, due to sediment loading, and when possible due to loading by changes in eustatic sea level, were removed, leaving that part of the subsidence, the tectonic subsidence, caused by cooling of the lithosphere or by other deep seated processes. The thermal cooling model theoretically predicts a linear relationship between tectonic subsidence and t½, where t is the time since subsidence began. This relationship should be obeyed during the first tens of Ma of subsidence. The slope of this curve depends upon the temperature to which the crust and upper mantle were heated during the initial rifting stage and can be used to derive the temperature–time history within the sediments, the present temperature distribution, and geothermal gradient. The data show that the observed subsidence curves behave in accordance with the thermal cooling model, at least during the first 80 Ma after subsidence began and obey the equation y = 300(± 80)t1/2 m, where y is the tectonic subsidence. The slopes of the subsidence curves are similar for the Labrador Shelf, the Nova Scotian Shelf, and the shelf off the northeastern U.S.A. More rapid and variable subsidence occurs northeast of Newfoundland and this may be associated, in a way yet to be established, with the anomalous foundered continental crust near the Orphan Knoll and Flemish Cap micro-continents which lie close to this area. After about 80 Ma, the subsidence appears to depart from the linear t1/2 law in a manner similar to the subsidence curves for oceanic crust, but this is not well established by the data. The present temperatures and temperature gradients computed using the slope of the subsidence curves show good agreement with measured values; geothermal gradients of 17.5 °C km−1 and 26 °C km−1 are calculated off Nova Scotia and Labrador respectively, and mean values of about 23 °C km−1 are observed. The computed temperature–time history within the sediments was used to estimate values of vitrinite reflectance, an indicator of the degree of organic metamorphism. These values show reasonable agreement with the measured values and suggest that only the Upper Jurassic and Lower Cretaceous sediments off Nova Scotia and the Paleocene sediments off Labrador are sufficiently mature to be good sources of petroleum. The linear t1/2 behaviour of the subsidence, and the good agreement between predicted and observed temperatures support the contention that cooling is largely responsible for the observed tectonic subsidence. The similarity of results from different areas suggests that the usefulness of the method is not restricted to a particular geographical area and may be applied to other rifted continental margins. Comparisons between the subsidence rates, thermal histories, and crustal structure at rifted margins on a worldwide scale may provide insights concerning the processes controlling their development. The temperature–time histories of the sediments estimated from the subsidence may be useful in establishing the potential of a rifted margin area for petroleum generation when little other information is available.


2000 ◽  
Vol 31 (1) ◽  
pp. 57-72 ◽  
Author(s):  
N. R. B. Olsen ◽  
D. K. Lysne

A three-dimensional numerical model was used to model water circulation and spatial variation of temperature in Lake Sperillen in Norway. A winter situation was simulated, with thermal stratification and ice cover. The numerical model solved the Navier-Stokes equations on a 3D unstructured non-orthogonal grid with hexahedral cells. The SIMPLE method was used for the pressure coupling and the k-ε model was used to model turbulence, with a modification for density stratification due to the vertical temperature profile. The results were compared with field measurements of the temperature in the lake, indicating the location of the water current. Reasonably good agreement was found.


Energies ◽  
2020 ◽  
Vol 13 (9) ◽  
pp. 2364 ◽  
Author(s):  
Hengxu Liu ◽  
Feng Yan ◽  
Fengmei Jing ◽  
Jingtao Ao ◽  
Zhaoliang Han ◽  
...  

This paper introduces a new point-absorber wave energy converter (WEC) with a moonpool buoy—the moonpool platform wave energy converter (MPWEC). The MPWEC structure includes a cylinder buoy and a moonpool buoy and a Power Take-off (PTO) system, where the relative movement between the cylindrical buoy and the moonpool buoy is exploited by the PTO system to generate energy. A 1:10 scale model was physically tested to validate the numerical model and further prove the feasibility of the proposed system. The motion responses of and the power absorbed by the MPWEC studied in the wave tank experiments were also numerically analyzed, with a potential approach in the frequency domain, and a computational fluid dynamics (CFD) code in the time domain. The good agreement between the experimental and the numerical results showed that the present numerical model is accurate enough, and therefore considering only the heave degree of freedom is acceptable to estimate the motion responses and power absorption. The study shows that the MPWEC optimum power extractions is realized over a range of wave frequencies between 1.7 and 2.5 rad/s.


2019 ◽  
Vol 9 (20) ◽  
pp. 4289 ◽  
Author(s):  
Sangki Park

In South Korea, the construction of new multi-unit residential structures has been continuously increasing in order to accommodate multiple households in single structures. However, the presence of walls and floors shared with neighbors makes these structures exceptionally vulnerable to floor noise transmission when the noise of everyday life occurs. In particular, South Korea has many social problems associated with such floor noise, which require the utmost attention and immediate resolution. In this study, a 17-story structure was selected as a test structure. Field measurements were carried out. A numerical model for the 17-story structure was developed in order to perform a vibro-acoustic analysis. The validation of the numerical model comparing with the field measurement data results shows a good agreement. Finally, it is concluded that numerical analysis can be applied to resolve floor noise problems arising in multi-unit residential structures.


2005 ◽  
Vol 42 (4) ◽  
pp. 1066-1085 ◽  
Author(s):  
Kianoosh Hatami ◽  
Richard J Bathurst

The paper describes a numerical model that was developed to simulate the response of three instrumented, full-scale, geosynthetic-reinforced soil walls under working stress conditions. The walls were constructed with a fascia column of solid modular concrete units and clean, uniform sand backfill on a rigid foundation. The soil reinforcement comprised different arrangements of a weak biaxial polypropylene geogrid reinforcement material. The properties of backfill material, the method of construction, the wall geometry, and the boundary conditions were otherwise nominally the same for each structure. The performance of the test walls up to the end of construction was simulated with the finite-difference-based Fast Lagrangian Analysis of Continua (FLAC) program. The paper describes FLAC program implementation, material properties, constitutive models for component materials, and predicted results for the model walls. The results predicted with the use of nonlinear elastic-plastic models for the backfill soil and reinforcement layers are shown to be in good agreement with measured toe boundary forces, vertical foundation pressures, facing displacements, connection loads, and reinforcement strains. Numerical results using a linear elastic-plastic model for the soil also gave good agreement with measured wall displacements and boundary toe forces but gave a poorer prediction of the distribution of strain in the reinforcement layers.Key words: numerical modelling, retaining walls, reinforced soil, geosynthetics, FLAC.


2020 ◽  
Author(s):  
Nicholas S. Tavouktsoglou ◽  
Aggelos Dimakopoulos ◽  
Jeremy Spearman ◽  
Richard J. S. Whitehouse

Abstract Submerged water jet causing soil excavation is a typical water-soil interaction process that occurs widely in many engineering disciplines. In hydraulic engineering for instance, a typical example would be scour downstream of headcuts, culverts, or dam spillways. In port and waterway engineering, erosion of the channel bed or quay wall by the propellers of passing ships are also typical water jet/soil interaction problems. In ocean engineering, trenching by impinging high-velocity water jets has been used as an efficient method for cable and pipeline burial. At present, physical modelling and simple prediction equations have been the main practical engineering tool for evaluating scour in these situations. However, with the increasing computational power of modern computers and the development of new Computational Fluid Dynamics (CFD) solvers, scour prediction in such engineering problems has become possible. In the present work three-dimensional (3D) numerical modelling has been applied to reproduce the capability of a pair of water jets to backfill an excavated trench. The simulations are carried out using a state-of-the-art three-dimensional Eulerian two-phase scour model based on the open source CFD software OpenFOAM. The fluid phase is resolved by solving modified Navier-Stokes equations, which take into consideration the influence of the solid phase, i.e., the soil particles. This paper first presents a validation of the numerical model against vertical jet erosion tests from the literature and conducted at HR Wallingford. The results of the model show good agreement with the experimental tests, with the numerical model predicting the scour hole depth and extent with good accuracy. The paper then presents a validation of the model’s ability to reproduce deposition which is evaluated through a comparison with settling velocity data and empirical formulations found in literature, again with the model showing good agreement. Finally, the model is applied to a prototype cable burial problem using a commercially available controlled flow jet excavator. The study found that the use of water jets can be effective (subject to confirmation of the time-scale required for real operations) for performing backfill operations but that the effectiveness is closely related to the type of sediment and selection of an appropriate jet discharge. As a result, in order for the water jet method to be effective for backfill, there is a requirement for a good description of the variation in sediment type along the trench and a requirement for the jet discharge to be varied as different sediment types are encountered.


Author(s):  
Aytaç Güven ◽  
Ahmed Hussein Mahmood

Abstract Spillways are constructed to evacuate the flood discharge safely not to let the flood wave overtop the dam body. There are different types of spillways, ogee type being the conventional one. Stepped spillway is an example of nonconventional spillways. The turbulent flow over stepped spillway was studied numerically by using the Flow-3D package. Different fluid flow characteristics such as longitudinal flow velocity, temperature distribution, density and chemical concentration can be well simulated by Flow-3D. In this study, the influence of slope changes on flow characteristics such as air entrainment, velocity distribution and dynamic pressures distribution over the stepped spillway was modelled by Flow-3D. The results from the numerical model were compared with the experimental study done by others in the literature. Two models of the stepped spillway with different discharge for each model was simulated. The turbulent flow in the experimental model was simulated by the Renormalized Group (RNG) turbulence scheme in the numerical model. A good agreement was achieved between the numerical results and the observed ones, which were exhibited in terms of graphics and statistical tables.


Sign in / Sign up

Export Citation Format

Share Document