A LOW-VOLTAGE LOW-POWER 10-BIT 200 MS/S PIPELINED ADC IN 90 NM CMOS

2010 ◽  
Vol 19 (02) ◽  
pp. 393-405 ◽  
Author(s):  
SAHEL ABDINIA ◽  
MOHAMMAD YAVARI
Keyword(s):  
Low Power ◽  
Low Voltage ◽  
Supply Voltage ◽  
Cmos Technology ◽  
Cmos Process ◽  
Pipelined Adc ◽  
Pipeline Adc ◽  
Class A ◽  
Reduction Techniques ◽  
Dynamic Comparators

This paper presents a low-power 10-bit 200 MS/s pipelined ADC in a 90 nm CMOS technology with 1 V supply voltage. To decrease the power dissipation efficiently, a new architecture using a combination of two power reduction techniques named double-sampling and opamp-sharing has been used to reduce the power consumption significantly, without any degradation in the performance of the ADC. In addition, the stage scaling technique has been applied to the ADC efficiently, and two-stage class A/AB and class A amplifiers and dynamic comparators have been used in sample and hold and sub-ADCs. According to HSPICE simulation results, the 10-bit 200 MSample/s pipeline ADC with a 9.375 MHz, 1-VP-P,diff input signal in a 90 nm CMOS process achieves a SNDR of 58.5 dB while consuming only 30.9 mW power from a 1 V supply voltage.

scholarly journals A 0.3 V Rail-to-Rail Ultra-Low-Power OTA with Improved Bandwidth and Slew Rate

2021 ◽  
Vol 11 (2) ◽  
pp. 19
Author(s):  
Francesco Centurelli ◽  
Riccardo Della Sala ◽  
Pietro Monsurrò ◽  
Giuseppe Scotti ◽  
Alessandro Trifiletti
Keyword(s):  
Low Power ◽  
Low Voltage ◽  
Supply Voltage ◽  
Cmos Process ◽  
Slew Rate ◽  
Large Signal ◽  
Output Stage ◽  
Ultra Low Power ◽  
Input Stage ◽  
Rail To Rail

In this paper, we present a novel operational transconductance amplifier (OTA) topology based on a dual-path body-driven input stage that exploits a body-driven current mirror-active load and targets ultra-low-power (ULP) and ultra-low-voltage (ULV) applications, such as IoT or biomedical devices. The proposed OTA exhibits only one high-impedance node, and can therefore be compensated at the output stage, thus not requiring Miller compensation. The input stage ensures rail-to-rail input common-mode range, whereas the gate-driven output stage ensures both a high open-loop gain and an enhanced slew rate. The proposed amplifier was designed in an STMicroelectronics 130 nm CMOS process with a nominal supply voltage of only 0.3 V, and it achieved very good values for both the small-signal and large-signal Figures of Merit. Extensive PVT (process, supply voltage, and temperature) and mismatch simulations are reported to prove the robustness of the proposed amplifier.

Low-Power and Reference-Less Data and Clock Recovery Circuit for Visible Light Receivers

2018 ◽  
Author(s):  
Ming-Cheng Liu ◽  
Paul C.-P. Chao ◽  
Soh Sze Khiong
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
Visible Light ◽  
Low Voltage ◽  
Supply Voltage ◽  
Clock And Data Recovery ◽  
Optical Receiver ◽  
Clock Recovery ◽  
Cmos Process ◽  
Rf Receiver

In this paper a low power all-digital clock and data recovery (ADCDR) with 1Mhz frequency has been proposed. The proposed circuit is designed for optical receiver circuit on the battery-less photovoltaic IoT (Internet of Things) tags. The conventional RF receiver has been replaced by the visible light optical receiver for battery-less IoT tags. With this proposed ADCDR a low voltage, low power consumption & tiny IoT tags can be fabricated. The proposed circuit achieve the maximum bandwidth of 1MHz, which is compatible with the commercial available LED and light sensor. The proposed circuit has been fabricated in TSMC 0.18um 1P6M standard CMOS process. Experimental results show that the power consumption of the optical receiver is approximately 5.58uW with a supply voltage of 1V and the data rate achieves 1Mbit/s. The lock time of the ADCDR is 0.893ms with 3.31ns RMS jitter period.

scholarly journals A Low-Voltage Low-Power Opamp-Less 8-bit 1-MS/s Pipelined ADC in 90-nm CMOS Technology

2014 ◽  
Vol 3 (6) ◽  
pp. 416-424
Author(s):  
Hamed Abbasizadeh ◽  
Behnam Samadpoor Rikan ◽  
Dong-Soo Lee ◽  
Abbas Syed Hayder ◽  
Kang-Yoon Lee
Keyword(s):  
Low Power ◽  
Low Voltage ◽  
Cmos Technology ◽  
Pipelined Adc

scholarly journals A New Low-Voltage Low-Power Dual-Mode VCII-Based SIMO Universal Filter

Electronics ◽  
2019 ◽  
Vol 8 (7) ◽  
pp. 765 ◽  
Author(s):  
Leila Safari ◽  
Gianluca Barile ◽  
Giuseppe Ferri ◽  
Vincenzo Stornelli
Keyword(s):  
Low Power ◽  
Transfer Functions ◽  
Low Voltage ◽  
Supply Voltage ◽  
Building Blocks ◽  
Cmos Technology ◽  
Universal Filter ◽  
Dual Mode ◽  
Input Multiple Output ◽  
Low Pass

In this paper, a new low-voltage low-power dual-mode universal filter is presented. The proposed circuit is implemented using inverting current buffer (I-CB) and second-generation voltage conveyors (VCIIs) as active building blocks and five resistors and three capacitors as passive elements. The circuit is in single-input multiple-output (SIMO) structure and can produce second-order high-pass (HP), band-pass (BP), low-pass (LP), all-pass (AP), and band-stop (BS) transfer functions. The outputs are available as voltage signals at low impedance Z ports of the VCII. The HP, BP, AP, and BS outputs are also produced in the form of current signals at high impedance X ports of the VCIIs. In addition, the AP and BS outputs are also available in inverting type. The proposed circuit enjoys a dual-mode operation and, based on the application, the input signal can be either current or voltage. It is worth mentioning that the proposed filter does not require any component matching constraint and all sensitivities are low, moreover it can be easily cascadable. The simulation results using 0.18 μm CMOS technology parameters at a supply voltage of ±0.9 V are provided to support the presented theory.

LOW VOLTAGE, LOW POWER CHEBYSHEV FILTER IN 0.18 μm CMOS TECHNOLOGY

2013 ◽  
Vol 22 (07) ◽  
pp. 1350053 ◽  
Author(s):  
S. REKHA ◽  
T. LAXMINIDHI
Keyword(s):  
Low Power ◽  
Dynamic Range ◽  
Low Voltage ◽  
Supply Voltage ◽  
Cmos Technology ◽  
Transconductance Amplifier ◽  
Low Pass ◽  
Unity Gain ◽  
Design Centering ◽  
Low Supply Voltage

This paper presents an active-RC continuous time filter in 0.18 μm standard CMOS technology intended to operate on a very low supply voltage of 0.5 V. The filter designed, has a 5th order Chebyshev low pass response with a bandwidth of 477 kHz and 1-dB passband ripple. A low-power operational transconductance amplifier (OTA) is designed which makes the filter realizable. The OTA uses bulk-driven input transistors and feed-forward compensation in order to increase the Dynamic Range and Unity Gain Bandwidth, respectively. The paper also presents an equivalent circuit of the OTA and explains how the filter can be modeled using descriptor state-space equations which will be used for design centering the filter in the presence of parasitics. The designed filter offers a dynamic range of 51.3 dB while consuming a power of 237 μW.

A Novel CNFET Technology Based 3 Bit Flash ADC for Low-Voltage High Speed SoC Application

2015 ◽  
Vol 19 ◽  
pp. 19-36 ◽  
Author(s):  
P.A. Gowri Sankar ◽  
G. Sathiyabama
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
Circuit Design ◽  
Field Effect ◽  
High Speed ◽  
Low Voltage ◽  
Supply Voltage ◽  
Cmos Technology ◽  
Flash Adc ◽  
Simulation Results

The continuous scaling down of metal-oxide-semiconductor field effect transistors (MOSFETs) led to the considerable impact in the analog-digital mixed signal integrated circuit design for system-on-chips (SoCs) application. SoCs trends force ADCs to be integrated on the chip with other digital circuits. These trends present new challenges in ADC circuit design based on existing CMOS technology. In this paper, we have designed and analyzed a 3-bit high speed, low-voltage and low-power flash ADC at 32nm CNFET technology for SoC applications. The proposed ADC utilizes the Threshold Inverter Quantization (TIQ) technique that uses two cascaded carbon nanotube field effect transistor (CNFET) inverters as a comparator. The TIQ technique proposed has been developed for better implementation in SoC applications. The performance of the proposed ADC is studied using two different types of encoders such as ROM and Fat tree encoders. The proposed ADCs circuits are simulated using Synopsys HSPICE with standard 32nm CNFET model at 0.9 input supply voltage. The simulation results show that the proposed 3 bit TIQ technique based flash ADC with fat tree encoder operates up to 8 giga samples per second (GSPS) with 35.88µW power consumption. From the simulation results, we observed that the proposed TIQ flash ADC achieves high speed, small size, low power consumption, and low voltage operation compared to other low power CMOS technology based flash ADCs. The proposed method is sensitive to process, temperature and power supply voltage variations and their impact on the ADC performance is also investigated.

An 8-Bit Ultra-Low-Power, Low-Voltage Current Steering DAC Utilizing a New Segmented Structure

2019 ◽  
Vol 28 (10) ◽  
pp. 1950172
Author(s):  
Mehdi Bandali ◽  
Alireza Hassanzadeh ◽  
Masoume Ghashghaie ◽  
Omid Hashemipour
Keyword(s):  
Low Power ◽  
Dynamic Range ◽  
Low Voltage ◽  
Supply Voltage ◽  
Cmos Technology ◽  
The Body ◽  
Current Steering ◽  
Ultra Low Power ◽  
Current Cell ◽  
Sample Rate

In this paper, an 8-bit ultra-low-power, low-voltage current steering digital-to-analog converter (DAC) is presented. The proposed DAC employs a new segmented structure that results in low integral nonlinearity (INL) and high spurious-free dynamic range (SFDR). Moreover, this DAC utilizes a low-voltage current cell. The low-voltage characteristic of the current cell is achieved by connecting the body of MOSFET switches to their sources. Utilizing a low supply voltage along with a low bias current in the current cells results in about 623.81-[Formula: see text]W power consumption in 140-MS/s sample rate, which is very small compared to previous reports. The post-layout simulation results in 180-nm CMOS technology and [Formula: see text]-V supply voltage with the sample rate of 140[Formula: see text]MS/s show SFDR [Formula: see text] 64.37[Formula: see text]dB in the Nyquist range. The differential nonlinearity (DNL) and INL of the presented DAC are 0.1254 LSB and 0.1491 LSB, respectively.

scholarly journals Ultra-Low-Voltage Low-Power Bulk-Driven Quasi-Floating-Gate Operational Transconductance Amplifier

2014 ◽  
Vol 2014 ◽  
pp. 1-7 ◽  
Author(s):  
Ziad Alsibai ◽  
Salma Bay Abo Dabbous
Keyword(s):  
Signal Processing ◽  
Power Consumption ◽  
Low Power ◽  
Low Voltage ◽  
Supply Voltage ◽  
Cmos Technology ◽  
Bias Current ◽  
Floating Gate ◽  
Operational Transconductance Amplifier ◽  
Transconductance Amplifier

A new ultra-low-voltage (LV) low-power (LP) bulk-driven quasi-floating-gate (BD-QFG) operational transconductance amplifier (OTA) is presented in this paper. The proposed circuit is designed using 0.18 μm CMOS technology. A supply voltage of ±0.3 V and a quiescent bias current of 5 μA are used. The PSpice simulation result shows that the power consumption of the proposed BD-QFG OTA is 13.4 μW. Thus, the circuit is suitable for low-power applications. In order to confirm that the proposed BD-QFG OTA can be used in analog signal processing, a BD-QFG OTA-based diodeless precision rectifier is designed as an example application. This rectifier employs only two BD-QFG OTAs and consumes only 26.8 μW.

scholarly journals A Low-Voltage, Low-Power Reconfigurable Current-Mode Softmax Circuit for Analog Neural Networks

Electronics ◽  
2021 ◽  
Vol 10 (9) ◽  
pp. 1004
Author(s):  
Massimo Vatalaro ◽  
Marco Lanuzza ◽  
Felice Crupi ◽  
Tatiana Moposita ◽  
Lionel Trojman ◽  
...  
Keyword(s):  
Low Power ◽  
Modular Design ◽  
Low Voltage ◽  
Supply Voltage ◽  
Current Mode ◽  
Cmos Technology ◽  
Chip Area ◽  
Analog Implementation ◽  
Efficient Option ◽  
P Type

This paper presents a novel low-power low-voltage analog implementation of the softmax function, with electrically adjustable amplitude and slope parameters. We propose a modular design, which can be scaled by the number of inputs (and of corresponding outputs). It is composed of input current–voltage linear converter stages (1st stages), MOSFETs operating in a subthreshold regime implementing the exponential functions (2nd stages), and analog divider stages (3rd stages). Each stage is only composed of p-type MOSFET transistors. Designed in a 0.18 µm CMOS technology (TSMC), the proposed softmax circuit can be operated at a supply voltage of 500 mV. A ten-input/ten-output realization occupies a chip area of 2570 µm2 and consumes only 3 µW of power, representing a very compact and energy-efficient option compared to the corresponding digital implementations.

An Ultra-Low-Voltage Low-Power Current-Mode True RMS-to-DC Converter

2016 ◽  
Vol 25 (06) ◽  
pp. 1650066 ◽  
Author(s):  
Pantre Kompitaya ◽  
Khanittha Kaewdang
Keyword(s):  
Integrated Circuits ◽  
Low Power ◽  
High Performance ◽  
Dynamic Range ◽  
Low Voltage ◽  
Supply Voltage ◽  
Circuit Complexity ◽  
Current Mode ◽  
Cmos Technology ◽  
Low Supply Voltage

A current-mode CMOS true RMS-to-DC (RMS: root-mean-square) converter with very low voltage and low power is proposed in this paper. The design techniques are based on the implicit computation and translinear principle by using CMOS transistors that operate in the weak inversion region. The circuit can operate for two-quadrant input current with wide input dynamic range (0.4–500[Formula: see text]nA) with an error of less than 1%. Furthermore, its features are very low supply voltage (0.8[Formula: see text]V), very low power consumption ([Formula: see text]0.2[Formula: see text]nW) and low circuit complexity that is suitable for integrated circuits (ICs). The proposed circuit is designed using standard 0.18[Formula: see text][Formula: see text]m CMOS technology and the HSPICE simulation results show the high performance of the circuit and confirm the validity of the proposed design technique.

Sign in / Sign up

Export Citation Format

Share Document