A Stable Mode-Selectable Oscillator with Variable Duty Cycle and High-Efficiency

2015 ◽  
Vol 24 (09) ◽  
pp. 1550132 ◽  
Author(s):  
Li-Ye Cheng ◽  
Xin-Quan Lai
Keyword(s):  
Duty Cycle ◽  
High Efficiency ◽  
Dynamic Performance ◽  
Operation Mode ◽  
Charge Pump ◽  
Input Voltage ◽  
Cmos Process ◽  
Pump Efficiency ◽  
Stable Mode ◽  
Wide Range

A mode-selectable oscillator (OSC) with variable duty cycle for improved charge pump efficiency is proposed in this paper. The novel OSC adjusts its duty cycle according to the operation mode of the charge pump, thus improves the charge-pump efficiency and dynamic performance. The control of variable duty cycle is implemented in digital logic hence it provides robust noise immunity and instantaneous response. The OSC and the charge-pump have been implemented in a 0.6-μm 40-V CMOS process. Experimental results show that the peak efficiency is 92.7% at 200-mA load, the recovery time is less than 25 μs and load transient is 15 mV under 500-mA load variation. The system is able to work under a wide range of input voltage (V IN ) in all modes with low EMI.

High-Efficiency Charge Pump LED Driver Circuit Design

2013 ◽  
Vol 389 ◽  
pp. 612-617 ◽  
Author(s):  
Yi Jiang Cao ◽  
Hao De ◽  
Jia Mu Cao ◽  
Xing Hua Tang ◽  
Qian Cui
Keyword(s):  
Electromagnetic Interference ◽  
High Efficiency ◽  
Circuit Simulation ◽  
Charge Pump ◽  
Input Voltage ◽  
Cmos Process ◽  
Led Driver ◽  
Simulation Tools ◽  
Driver Circuit ◽  
Static Power

In this paper, Using CSMC 0.5μm CMOS process to design each sub-module, the circuit simulation, and adjustment and validation of parameters have been carried out by simulation tools. The low static power and high conversion efficiency charge pump LED driver circuit has been designed. The circuits nucleus module is adaptive charge pump (1x/1.5x/2x charge pump), to converse a wider range of input voltage to a constant output voltage with high efficiency. This circuit only needs some external capacitors, and dont need inductor. So it reduces EMI electromagnetic interference and application cost, etc.

scholarly journals Step-Up Series Resonant DC–DC Converter with Bidirectional-Switch-Based Boost Rectifier for Wide Input Voltage Range Photovoltaic Applications

Energies ◽  
2020 ◽  
Vol 13 (14) ◽  
pp. 3747 ◽  
Author(s):  
Abualkasim Bakeer ◽  
Andrii Chub ◽  
Dmitri Vinnikov
Keyword(s):  
Theoretical Analysis ◽  
Duty Cycle ◽  
Input Voltage ◽  
Voltage Regulation ◽  
Switching Frequency ◽  
Voltage Gain ◽  
Voltage Range ◽  
Dc Voltage ◽  
Wide Range ◽  
Series Resonant

This paper proposes a high gain DC–DC converter based on the series resonant converter (SRC) for photovoltaic (PV) applications. This study considers low power applications, where the resonant inductance is usually relatively small to reduce the cost of the converter realization, which results in low-quality factor values. On the other hand, these SRCs can be controlled at a fixed switching frequency. The proposed topology utilizes a bidirectional switch (AC switch) to regulate the input voltage in a wide range. This study shows that the existing topology with a bidirectional switch has a limited input voltage regulation range. To avoid this issue, the resonant tank is rearranged in the proposed converter to the resonance capacitor before the bidirectional switch. By this rearrangement, the dependence of the DC voltage gain on the duty cycle is changed, so the proposed converter requires a smaller duty cycle than that of the existing counterpart at the same gain. Theoretical analysis shows that the input voltage regulation range is extended to the region of high DC voltage gain values at the maximum input current. Contrary to the existing counterpart, the proposed converter can be realized with a wide range of the resonant inductance values without compromising the input voltage regulation range. Nevertheless, the proposed converter maintains advantages of the SRC, such as zero voltage switching (ZVS) turn-on of the primary-side semiconductor switches. In addition, the output-side diodes are turned off at zero current. The proposed converter is analyzed and compared with the existing counterpart theoretically and experimentally. A 300 W experimental prototype is used to validate the theoretical analysis of the proposed converter. The peak efficiency of the converter is 96.5%.

scholarly journals Impact of Transformer Turns Ratio on the Power Losses and Efficiency of the Wide Range Isolated Buck–Boost Converter for Photovoltaic Applications

Energies ◽  
2020 ◽  
Vol 13 (21) ◽  
pp. 5645
Author(s):  
Hamed Mashinchi Maheri ◽  
Dmitri Vinnikov ◽  
Andrii Chub ◽  
Vadim Sidorov ◽  
Elizaveta Liivik
Keyword(s):  
High Efficiency ◽  
Input Voltage ◽  
Power Losses ◽  
Efficient Operation ◽  
Wide Range ◽  
Photovoltaic Applications ◽  
Theoretical Predictions ◽  
Converter Topology ◽  
Isolation Transformer ◽  
The Impact

In this paper, the impact of transformer turns ratio on the performance of the quasi-Z-source galvanically isolated DC-DC converters is studied. Embedded buck–boost functionality enables these converters to regulate the input voltage and load in a wide range, which makes them suitable for such demanding application as photovoltaic microconverters. The isolation transformer here plays a central role as its turns ratio defines the point of transition between the boost and buck modes and overall capability of the converter to regulate the input voltage in a wide range at high efficiency. The studied quasi-Z-source galvanically isolated DC-DC converter is benchmarked in terms of power loss of components and weighted power conversion efficiency for three different turns ratios of isolation transformer to achieve the best and optimized turns ratio lead to the efficient operation. Operation in a wide range of input voltage at high efficiency is the main criterion for assessing the effect of turns ratio on the efficiency of the converter. The proposed loss model and theoretical predictions of the efficiency were validated with the help of a 300 W experimental prototype of the photovoltaic microconverter based on the quasi-Z-source galvanically isolated DC-DC converter topology.

scholarly journals A Structure-Reconfigurable Soft-Switching DC-DC Converter for Wide-Range Applications

Energies ◽  
2019 ◽  
Vol 12 (15) ◽  
pp. 2905 ◽  
Author(s):  
Xianxu Huo ◽  
Ke Xu ◽  
Ruixin Liu ◽  
Xi Chen ◽  
Zhanchun Li ◽  
...  
Keyword(s):  
Direct Current ◽  
High Efficiency ◽  
Zero Point ◽  
Input Voltage ◽  
Optimal Switching ◽  
Peak Efficiency ◽  
Loss Analysis ◽  
Wide Range ◽  
Analysis Calculation ◽  
Current Converter

In this paper, a structure-reconfigurable resonant DC-DC (direct current – direct current) converter is presented. By controlling the state of the auxiliary switch, the converter could change the resonant structure to acquire a high efficiency and wide voltage gain range simultaneously. The characteristics of the LLC (inductor-inductor-capacitor) resonant converter are firstly analyzed. Based on this, through introducing additional resonant elements and adopting the topology morphing method, the proposed converter can be formed. Moreover, a novel parameter selection method is discussed to satisfy both working states. Then, a detailed loss analysis calculation is conducted to determine the optimal switching point. In addition, an extra resonant zero point is generated by the topology itself, and the inherent over-current protection is guaranteed. Finally, a 500 W prototype is built to demonstrate the theoretical rationality. The output voltage is constant at 400 V even if the input voltage varies from 160 to 400 V. A peak efficiency of 97.2% is achieved.

A High-Efficiency Switched-Capacitance HTFET Charge Pump for Low-Input-Voltage Applications

2015 ◽  
Author(s):  
Unsuk Heo ◽  
Xueqing Li ◽  
Huichu Liu ◽  
Sumeet Gupta ◽  
Suman Datta ◽  
...  
Keyword(s):  
High Efficiency ◽  
Charge Pump ◽  
Input Voltage ◽  
Low Input

scholarly journals Wide-Range Operation of High Step-Up DC-DC Converters with Multimode Rectifiers

Electronics ◽  
2021 ◽  
Vol 10 (8) ◽  
pp. 914
Author(s):  
Andrii Chub ◽  
Dmitri Vinnikov ◽  
Oleksandr Korkh ◽  
Tanel Jalakas ◽  
Galina Demidova
Keyword(s):  
Duty Cycle ◽  
Input Voltage ◽  
Voltage Range ◽  
Front End ◽  
Wide Range ◽  
Theoretical Predictions

This paper discusses the essence and application specifics of the multimode rectifiers in high step-up DC-DC converters. It presents an overview of existing multimode rectifiers. Their use enables operation in the wide input voltage range needed in highly demanding applications. Owing to the rectifier mode changes, the converter duty cycle can be restricted to a range with a favorable efficiency. It is shown that the performance of such converters depends on the front-end inverter type. The study considers current- and impedance-source front-end topologies, as they are the most relevant in high step-up applications. It is explained why the full- and half-bridge implementations provide essentially different performances. Unlike the half-bridge, the full-bridge implementation shows step changes in efficiency during the rectifier mode changes, which could compromise the long-term reliability of the converter. The theoretical predictions are corroborated by experimental examples to compare performance with different boost front-end inverters.

scholarly journals A Comparative Analysis of Half-Bridge LLC Resonant Converters Using Si and SiC MOSFETs

2021 ◽  
Vol 12 (1) ◽  
pp. 43
Author(s):  
Hasaan Farooq ◽  
Hassan Abdullah Khalid ◽  
Waleed Ali ◽  
Ismail Shahid
Keyword(s):  
Silicon Carbide ◽  
Renewable Energy ◽  
High Frequency ◽  
High Efficiency ◽  
Low Voltage ◽  
Low Cost ◽  
Renewable Energy Sources ◽  
Input Voltage ◽  
Resonant Converters ◽  
Wide Range

With the expansion of renewable energy sources worldwide, the need for developing more economical and more efficient converters that can operate on a high frequency with minimal switching and conduction losses has been increased. In power electronic converters, achieving high efficiency is one of the most challenging targets to achieve. The utilization of wideband switches can achieve this goal but add additional cost to the system. LLC resonant converters are widely used in different applications of renewable energy systems, i.e., PV, wind, hydro and geothermal, etc. This type of converter has more benefits than the other converters such as high electrical isolation, high power density, low EMI, and high efficiency. In this paper, a comparison between silicon carbide (SiC) MOSFET and silicon (Si) MOSFET switches was made, by considering a 3KW half-bridge LLC converter with a wide range of input voltage. The switching losses and conduction losses were analyzed through mathematical calculations, and their authenticity was validated with the help of software simulations in PSIM. The results show that silicon carbide (SiC) MOSFETs can work more efficiently, as compared with silicon (Si) MOSFETs in high-frequency power applications. However, in low-voltage and low-power applications, Si MOSFETs are still preferable due to their low-cost advantage.

Fast Transient Capacitor-Less Low-Dropout Regulator Based on Output Voltage Spike Reduction Circuits for SOC Applications

2019 ◽  
Vol 28 (03) ◽  
pp. 1950043 ◽  
Author(s):  
M. Jahangiri ◽  
A. Farrokhi
Keyword(s):  
Output Voltage ◽  
Input Voltage ◽  
Cmos Process ◽  
Ultra Low Power ◽  
Wide Range ◽  
Unity Gain ◽  
Fast Transient ◽  
Low Dropout Regulator ◽  
On Chip ◽  
Voltage Spike

A fast transient capacitor-less low-dropout regulator is presented in this study. The proposed LDO structure is based on Output Voltage Spike Reduction (OVSR) circuits and capacitance compensation circuits to enable a fast-transient response with ultra-low power dissipation and to make the LDO stable for a wide range of output load currents (0–50[Formula: see text]mA). The slew rate is improved with more slew current from the OVSR circuit and unity gain bandwidth is improved by a capacitor multiplayer circuit. The proposed LDO has been simulated with a standard 0.18[Formula: see text][Formula: see text]m CMOS process. The output voltage of the LDO was set to 1.2[Formula: see text]V for an input voltage of 1.4–2[Formula: see text]V. The Simulation results verify that the transient times are less than 2.8[Formula: see text][Formula: see text]s and the maximum undershoot and overshoot are 20[Formula: see text]mV while consuming only 26[Formula: see text][Formula: see text]A quiescent current. The proposed LDO is stable with an on-chip capacitor at the output node within the wide range of 1100[Formula: see text]PF.

scholarly journals A Modified Step-Up DC-DC Flyback Converter with Active Snubber for Improved Efficiency

Energies ◽  
2019 ◽  
Vol 12 (11) ◽  
pp. 2066 ◽  
Author(s):  
Cristian Pesce ◽  
Javier Riedemann ◽  
Ruben Pena ◽  
Werner Jara ◽  
Camilo Maury ◽  
...  
Keyword(s):  
Output Voltage ◽  
High Efficiency ◽  
Controller Design ◽  
Current Mode ◽  
Input Voltage ◽  
Input Power ◽  
Good Efficiency ◽  
Main Research ◽  
Flyback Converter ◽  
Wide Range

The research on DC-DC power converters has been a matter of interest for years since this type of converter can be used in a wide range of applications. The main research is focused on increasing the converter voltage gain while obtaining a good efficiency and reliability. Among the different DC-DC converters, the flyback topology is well-known and widely used. In this paper, a novel high efficiency modified step-up DC-DC flyback converter is presented. The converter is based on a N-stages flyback converter with parallel connected inputs and series-connected outputs. The use of a single main diode and output capacitor reduces the number of passive elements and allows for a more economical implementation compared with interleaved flyback topologies. High efficiency is obtained by including an active snubber circuit, which returns the energy stored in the leakage inductance of the flyback transformers back to the input power supply. A 4.7 kW laboratory prototype is implemented considering four flyback stages with an input voltage of 96 V and an output voltage of 590 V, obtaining an efficiency of 95%. The converter operates in discontinuous current mode then facilitating the output voltage controller design. Experimental results are presented and discussed.

Sign in / Sign up

Export Citation Format

Share Document