Peculiarities of Photorefractive Response in Planar Waveguides Fabricated by Combined Proton and Copper Exchange

1997 ◽  
Vol 06 (03) ◽  
pp. 321-331 ◽  
Author(s):  
Sergey Kostritskii
Keyword(s):  
Experimental Investigation ◽  
Photorefractive Effect ◽  
Planar Waveguides ◽  
Ionic Exchange ◽  
Wide Range ◽  
Infra Red ◽  
Anomalous Character ◽  
A New Technique ◽  
Fabrication Parameters ◽  
Copper Exchange

In this work a photorefractive effect in proton-exchanged planar waveguides on LiNbO 3 crystals is discussed. These waveguides are doped by copper with the aid of a new technique using the low-temperature ionic exchange. The experimental investigation has revealed the anomalous character of the photorefractive response in strongly doped waveguides. Photorefractive measurements are made over a wide range of H +, Cu + and Cu 2+ concentrations, altered by a seriesof oxidation treatments caused by back ionic exchange. Fabrication parameters allowing the realization of high photorefractive sensitivity either in visible or near infra-red ranges are identified.

scholarly journals Pulsed Electromagnetic Cross-Well Exploration for Monitoring Permafrost and Examining the Processes of Its Geocryological Changes

Geosciences ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 60
Author(s):  
Viacheslav Glinskikh ◽  
Oleg Nechaev ◽  
Igor Mikhaylov ◽  
Kirill Danilovskiy ◽  
Vladimir Olenchenko
Keyword(s):  
High Performance ◽  
Geophysical Methods ◽  
Three Dimensional ◽  
High Sensitivity ◽  
Data Interpretation ◽  
Industrial Facilities ◽  
Wide Range ◽  
Vector Finite Element ◽  
A New Technique ◽  
Pulsed Electromagnetic

This paper is dedicated to the topical problem of examining permafrost’s state and the processes of its geocryological changes by means of geophysical methods. To monitor the cryolithozone, we proposed and scientifically substantiated a new technique of pulsed electromagnetic cross-well sounding. Based on the vector finite-element method, we created a mathematical model of the cross-well sounding process with a pulsed source in a three-dimensional spatially heterogeneous medium. A high-performance parallel computing algorithm was developed and verified. Through realistic geoelectric models of permafrost with a talik under a highway, constructed following the results of electrotomography field data interpretation, we numerically simulated the pulsed sounding on the computing resources of the Siberian Supercomputer Center of SB RAS. The simulation results suggest the proposed system of pulsed electromagnetic cross-well monitoring to be characterized by a high sensitivity to the presence and dimensions of the talik. The devised approach can be oriented to addressing a wide range of issues related to monitoring permafrost rocks under civil and industrial facilities, buildings, and constructions.

Experimental Investigation of Subsonic Turbulent Flow Over Single and Double Backward Facing Steps

1962 ◽  
Vol 84 (3) ◽  
pp. 317-325 ◽  
Author(s):  
D. E. Abbott ◽  
S. J. Kline
Keyword(s):  
Experimental Investigation ◽  
Velocity Profile ◽  
Flow Pattern ◽  
Reynolds Numbers ◽  
Area Ratio ◽  
Single Step ◽  
Reattachment Length ◽  
Double Step ◽  
Wide Range ◽  
Geometric Variables

Results are presented for flow patterns over backward facing steps covering a wide range of geometric variables. Velocity profile measurements are given for both single and double steps. The stall region is shown to consist of a complex pattern involving three distinct regions. The double step contains an assymmetry for large expansions, but approaches the single-step configuration with symmetric stall regions for small values of area ratio. No effect on flow pattern or reattachment length is found for a wide range of Reynolds numbers and turbulence intensities, provided the flow is fully turbulent before the step.

Automation and Management of Design Process of the Main Drive for an Innovative Fruits and Vegetables Washer

2021 ◽  
Vol 27 (1) ◽  
pp. 9-17
Author(s):  
V. P. Bui ◽  
◽  
S. S. Gavruishin ◽  
V. B. Phung ◽  
H. M. Dang ◽  
...  
Keyword(s):  
Design Process ◽  
Rational Design ◽  
Fruits And Vegetables ◽  
Rational Solution ◽  
Quality Criteria ◽  
Pareto Optimal ◽  
Optimal Domain ◽  
Wide Range ◽  
A New Technique ◽  
New Generation

A new technique is described, used by the authors to automate the design process of the main drive of a new generation machine intended for industrial washing of fruits and vegetables. To solve the problem of multi-criteria design, the original approach is proposed that uses interconnected mathematical models describing the dynamic behavior, strength reliability and functional characteristics of the machine in a unified information space. The generalized mathematical model includes 12 controlled parameters, 16 functional constraints, and 3 quality criteria. A genetic algorithm was used to find the space of Pareto-optimal solutions. The situational approach was used to select the final rational solution from a set of solutions belonging to the Pareto-optimal domain. The rational design of option the washer found using the proposed approach is compared with the existing ones. The proposed design methodology can be recommended for the design of a wide range of similar mechanical structures.

Experimental investigation of isothermal and reacting flow characteristics downstream of axisymmetric bluff body stabilizers under stratified or fully premixed inlet mixture conditions

2020 ◽  
Author(s):  
Γεώργιος Πατεράκης
Keyword(s):  
Experimental Investigation ◽  
Turbulent Flow ◽  
Bluff Body ◽  
Operating Conditions ◽  
Reacting Flow ◽  
Wide Range ◽  
Flow Features ◽  
Air Mixing ◽  
The Impact ◽  
Stratified Flames

The current work describes an experimental investigation of isothermal and turbulent reacting flow field characteristics downstream of axisymmetric bluff body stabilizers under a variety of inlet mixture conditions. Fully premixed and stratified flames established downstream of this double cavity premixer/burner configuration were measured and assessed under lean and ultra-lean operating conditions. The aim of this thesis was to further comprehend the impact of stratifying the inlet fuelair mixture on the reacting wake characteristics for a range of practical stabilizers under a variety of inlet fuel-air settings. In the first part of this thesis, the isothermal mean and turbulent flow features downstream of a variety of axisymmetric baffles was initially examined. The effect of different shapes, (cone or disk), blockage ratios, (0.23 and 0.48), and rim thicknesses of these baffles was assessed. The variations of the recirculation zones, back flow velocity magnitude, annular jet ejection angles, wake development, entrainment efficiency, as well as several turbulent flow features were obtained, evaluated and appraised. Next, a comparative examination of the counterpart turbulent cold fuel-air mixing performance and characteristics of stratified against fully-premixed operation was performed for a wide range of baffle geometries and inlet mixture conditions. Scalar mixing and entrainment properties were investigated at the exit plane, at the bluff body annular shear layer, at the reattachment region and along the developing wake were investigated. These isothermal studies provided the necessary background information for clarifying the combustion properties and interpreting the trends in the counterpart turbulent reacting fields. Subsequently, for selected bluff bodies, flame structures and behavior for operation with a variety of reacting conditions were demonstrated. The effect of inlet fuel-air mixture settings, fuel type and bluff body geometry on wake development, flame shape, anchoring and structure, temperatures and combustion efficiencies, over lean and close to blow-off conditions, was presented and analyzed. For the obtained measurements infrared radiation, particle image velocimetry, laser doppler velocimetry, chemiluminescence imaging set-ups, together with Fouriertransform infrared spectroscopy, thermocouples and global emission analyzer instrumentation was employed. This helped to delineate a number of factors that affectcold flow fuel-air mixing, flame anchoring topologies, wake structure development and overall burner performance. The presented data will also significantly assist the validation of computational methodologies for combusting flows and the development of turbulence-chemistry interaction models.

scholarly journals Buckling behavior of cold-formed steel columns at both ambient temperature and simulated fire conditions

Fire Research ◽  
2016 ◽  
Author(s):  
Hélder D. Craveiro ◽  
João Paulo C. Rodrigues ◽  
Luís M. Laím
Keyword(s):  
Experimental Investigation ◽  
Ambient Temperature ◽  
Cross Sections ◽  
Failure Modes ◽  
Steel Columns ◽  
Buckling Behavior ◽  
Wide Range ◽  
Cold Formed Steel ◽  
Simulated Fire ◽  
Fire Conditions

Cold-formed steel (CFS) profiles with a wide range of cross-section shapes are commonly used in building construction industry. Nowadays several cross-sections can be built using the available standard single sections (C, U, Σ, etc.), namely open built-up and closed built-up cross-sections. This paper reports an extensive experimental investigation on the behavior of single and built-up cold-formed steel columns at both ambient and simulated fire conditions considering the effect of restraint to thermal elongation. The buckling behavior, ultimate loads and failure modes, of different types of CFS columns at both ambient and simulated fire conditions with restraint to thermal elongation, are presented and compared. Regarding the buckling tests at ambient temperature it was observed that the use of built-up cross-sections ensures significantly higher values of buckling loads. Especially for the built-up cross-sections the failure modes were characterized by the interaction of individual buckling modes, namely flexural about the minor axis, distortional and local buckling. Regarding the fire tests, it is clear that the same levels of restraint used in the experimental investigation induce different rates in the generated restraining forces due to thermal elongation of the columns. Another conclusion that can be drawn from the results is that by increasing the level of restraint to thermal elongation the failure of the columns is controlled by the generated restraining forces, whereas for lower levels of restraint the temperature plays a more important role. Hence, higher levels of imposed restraint to thermal elongation will lead to higher values of generated restraining forces and eventually to lower values of critical temperature and time.

scholarly journals Experimental investigation of rockwool insulation hygrothermal properties related to material structure

2015 ◽  
Vol 19 (3) ◽  
pp. 923-928 ◽  
Author(s):  
Maja Djurovic-Petrovic
Keyword(s):  
Thermal Conductivity ◽  
Experimental Investigation ◽  
Sorption Properties ◽  
Material Structure ◽  
Insulation Material ◽  
Wide Range ◽  
Two Samples

The hygrothermal properties related to rockwool insulation material structure with different additives are presented using rockwool insulation products obtained from row material of southern Serbia (Vranje region) in the wide range of reference temperatures (10?C to 70?C). The hygrothermal properties of basic sample (without additives) are compared to two samples with different additives for two sets of rockwool insulation samples namely: light-soft-panels (LSP) with density of 50 kg/m3, and middle-weight-panels (MWP) with density of 80 kg/m3. It is shown that there is significant (approximately 10%) improvement of thermal conductivity for additives based on zeolite. Also, correlation of thermal conductivity and sorption properties of selected samples are presented.

Tuning the Mechanical and Geometric Properties of Electrochemically Aligned Collagen Threads Towards Applications in Biohybrid Robotics

2021 ◽  
Author(s):  
Wenhuan Sun ◽  
Jason Paulovich ◽  
Victoria Webster-Wood
Keyword(s):  
Tensile Modulus ◽  
Solution Concentration ◽  
Cross Sectional ◽  
Geometric Properties ◽  
Wide Range ◽  
Crosslinker Concentration ◽  
High Degree ◽  
The Impact ◽  
Fabrication Parameters ◽  
Manufacturing Parameters

Abstract Electrochemically Aligned Collagen (ELAC) threads fabricated by the isoelectric focusing (IF) of collagen have previously shown potential in tissue engineering and more recently in the fabrication of biohybrid robot structures. For applications in biohybrid robotics, ELAC structures are needed that are both robust and compliant enough to facilitate muscle actuation. However, studies on the effects of IF parameters, and the interactions of such fabrication parameters, on the mechanical and geometric properties of resulting ELAC threads have not been previously found in literature. Understanding the impact of these manufacturing parameters on the material properties is critical to facilitate biohybrid robot design. In this study, the effects of IF duration, IF voltage, and collagen solution concentration were investigated and showed statistically significant effects on adjusting ELAC properties via single-factor experiments. The interactions between parameters exhibited significant joint effects on ELAC property tuning through two-factor experiments. Scanning electron microscopy and 2,4,6-trinitrobenzenesulfonic assays revealed the correlation between high mechanical properties and a combination of low porosity and high degree of crosslinking. By simply tuning IF parameters without changing other fabrication steps, such as crosslinker concentration, ELAC threads with a wide range of mechanical and geometric properties were fabricated. The average tensile modulus of the resulting ELAC threads ranged from 198±90 to 758±138 MPa. The average cross-sectional area ranged from 7756±1000 to 1775±457 µm2. The resultant mapping between IF parameters and ELAC thread properties enabled the production of strong and flexible threads with customizable properties.

Domestic Outsourcing and Workers’ Bargaining Power in a Simple Production System

2020 ◽  
Vol 39 (1) ◽  
pp. 42-56
Author(s):  
Aldo Barba
Keyword(s):  
Technical Progress ◽  
Technical Change ◽  
Production System ◽  
Bargaining Power ◽  
Wide Range ◽  
Regulated Firms ◽  
Domestic Outsourcing ◽  
A New Technique ◽  
Distributive Conflict ◽  
Simple Production

Abstract Outsourcing is normally conceived as the result of a cost-minimizing choice of a new technique that also implies a redefinition of the boundaries between firms and sectors. In this paper, we will argue instead that many outsourcing activities do not necessarily imply technical change and that the phenomenon can be explained by placing it in connection with the radical modification of the way in which wages are set for workers in a wide range of poorly regulated firms and industries. More than as an aspect of the spread of technical progress, outsourcing will be analyzed as an important mechanism through which workers are divided and their bargaining power is weakened, thus changing the outcome of the distributive conflict between profit and wages.

Waveguides Fabricated in LiNbO3 by Proton Implantation

1991 ◽  
Vol 244 ◽  
Author(s):  
P. Moretti ◽  
P. Thevenard ◽  
K. Wirl ◽  
P. Hertel
Keyword(s):  
Refractive Index ◽  
Refractive Index Profile ◽  
Planar Waveguides ◽  
Optical Barrier ◽  
Dark Line ◽  
Wide Range ◽  
Ion Energies ◽  
Optical Planar Waveguides ◽  
Proton Implantation ◽  
Mode Spectroscopy

ABSTRACTOptical planar waveguides, with a controllable thickness in a very wide range, typically from 3 to 20 μm, can be fabricated by thermally controlled proton implantation in LiNbO3. In the nuclear stopping region at the end of the ion's tracks a sufficient decrease in refractive index is obtained, thus forming an adequate optical barrier. The mode confinement was investigated by dark line mode spectroscopy, and the refractive index profiles were reconstructed. The effects of different ion fluences and ion energies in the Mev range on the refractive index profile at 300 K have been investigated.

Sign in / Sign up

Export Citation Format

Share Document