Quantification of conservative endurance times in thermally insulated cold-stressed digits

1991 ◽  
Vol 71 (6) ◽  
pp. 2528-2535 ◽  
Author(s):  
A. Shitzer ◽  
L. A. Stroschein ◽  
W. R. Santee ◽  
R. R. Gonzalez ◽  
K. B. Pandolf
Keyword(s):  
Cold Stress ◽  
Thermal Insulation ◽  
Heat Generation ◽  
Blood Perfusion ◽  
Measured Data ◽  
Cold Weather ◽  
Maximum Deviation ◽  
Conservative Estimation ◽  
Environmental Temperatures ◽  
Volumetric Heat Generation

The estimation of endurance times of the digits exposed to cold weather is performed by an analytical, one-dimensional cylindrical model. Blood perfusion effects are lumped into a volumetric heat-generation term. Cold-induced vasodilatation (CIVD) effects are not included in the present analysis. Endurance times, defined by a drop in cylinder tip temperature to 5 degrees C, were evaluated. Parameters included in this evaluation were 1) environmental temperatures, 2) thermal insulation applied on the cylinder, 3) length of the cylinder, and 4) diameter of the cylinder. It was found that the lower the ambient temperature, the longer the finger, and the smaller its diameter, then the shorter the endurance time for the same thermal insulation. Results of the model were compared with measured data for a subject not exhibiting CIVD response to cold stress. Conformity of results calculated for an adjusted value of the volumetric heat-generation term and measured data was very good, with a maximum deviation of less than 10% at only one particular point in time. This model facilitates the conservative estimation of lower bounds to thermally insulated fingers and toes exposed to cold stress.

Thermal Insulation Performances of Plaster Composites Based on Embedding Natural Rubber Latex Compound

2021 ◽  
Vol 904 ◽  
pp. 441-446
Author(s):  
Nuchnapa Tangboriboon ◽  
Sarun Muntongkaw ◽  
Sompratthana Pianklang
Keyword(s):  
Natural Rubber ◽  
Thermal Insulation ◽  
Water Solubility ◽  
Testing Machine ◽  
Natural Rubber Latex ◽  
Cold Weather ◽  
Mechanical And Thermal Properties ◽  
Rubber Latex ◽  
Universal Testing ◽  
Cost Of Energy

Adding 0, 20, and 50 wt% natural-rubber latex compound into the plaster ceiling matrix affected to increase the physical-mechanical-thermal performance properties of plaster ceiling composites. Adding 50 wt% natural rubber latex compound into plaster composites can increase the superior adhesion of the nail-tensile resistance equal to 57.54 N and decrease thermal conductivity equal to 0.0634 W/m.K. In addition, adding natural rubber latex compounds into plaster composites can reduce water solubility, brittleness, impact, and cost of energy consumption due to the exterior temperature. Adequate thermal insulation for roofing, ceiling, and wall systems also reduces radiative losses that chill occupants in cold weather, and reduce interior surface temperatures in the summer, thereby optimizing the comfort of building occupants. The mechanical and thermal properties of plaster composites were investigated by using a Universal Testing Machine (UTM) and heat flow meter, respectively, measured according to TIS 1211-50, TIS 219-2522, and ASTM C518.

scholarly journals Internal volumetric heat generation and heat capacity prediction during a material electromagnetic treatment process using hybrid algorithms

2018 ◽  
Vol 38 (1) ◽  
pp. 74-82
Author(s):  
Edgar García-Morantes ◽  
Iván Amaya-Contreras ◽  
Rodrigo Correa-Cely
Keyword(s):  
Inverse Problem ◽  
Heat Capacity ◽  
Electromagnetic Field ◽  
Heat Generation ◽  
Initial Conditions ◽  
Limited Range ◽  
First Case ◽  
Realistic Situation ◽  
Wide Range ◽  
Volumetric Heat Generation

This work considers the estimation of internal volumetric heat generation, as well as the heat capacity of a solid spherical sample, heated by a homogeneous, time-varying electromagnetic field. To that end, the numerical strategy solves the corresponding inverse problem. Three functional forms (linear, sinusoidal, and exponential) for the electromagnetic field were considered. White Gaussian noise was incorporated into the theoretical temperature profile (i.e. the solution of the direct problem) to simulate a more realistic situation. Temperature was pretended to be read through four sensors. The inverse problem was solved through three different kinds of approach: using a traditional optimizer, using modern techniques, and using a mixture of both. In the first case, we used a traditional, deterministic Levenberg-Marquardt (LM) algorithm. In the second one, we considered three stochastic algorithms: Spiral Optimization Algorithm (SOA), Vortex Search (VS), and Weighted Attraction Method (WAM). In the final case, we proposed a hybrid between LM and the metaheuristics algorithms. Results show that LM converges to the expected solutions only if the initial conditions (IC) are within a limited range. Oppositely, metaheuristics converge in a wide range of IC but exhibit low accuracy. The hybrid approaches converge and improve the accuracy obtained with the metaheuristics. The difference between expected and obtained values, as well as the RMS errors, are reported and compared for all three methods.

Analytical Study of Natural Convection in a Cavity With Volumetric Heat Generation

Volume 1 ◽  
2004 ◽  
Author(s):  
Mandar V. Joshi ◽  
U. N. Gaitonde ◽  
Sushanta K. Mitra
Keyword(s):  
Natural Convection ◽  
Aspect Ratio ◽  
Heat Generation ◽  
Central Region ◽  
Analytical Study ◽  
Vertical Direction ◽  
Maximum Temperature ◽  
Small Aspect Ratio ◽  
Governing Equations ◽  
Volumetric Heat Generation

A semi-analytical method for natural convection in a two dimensional rectangular enclosure, with uniform volumetric heat generation, having insulated horizontal boundaries, and isothermal vertical boundaries, has been studied here. In this method, the governing equations for natural convection, have been solved under the assumption that for a cavity with small aspect ratio, the flow in the central region of the cavity is only in the vertical direction. It is found that for the cavities with small aspect ratio, the temperature in central region of the cavity is nearly constant along the horizontal direction. However, there is a uniform temperature gradient in the vertical direction, which can be related to the maximum temperature in conduction. The velocity profiles and temperature profiles obtained in the present work, are compared with the numerical simulations by Fluent and a fair agreement is found between these results.

A Comparative Analysis of the Tumor Pathology and the Metabolic Heat Generation of Growing Malignant Tumors

2020 ◽  
Author(s):  
Alyssa Owens ◽  
Manasi Godbole ◽  
Donnette Dabydeen ◽  
Lori Medeiros ◽  
Pradyumna Phatak ◽  
...  
Keyword(s):  
Breast Cancer ◽  
Heat Generation ◽  
Infrared Imaging ◽  
Malignant Tumors ◽  
Blood Perfusion ◽  
The United States ◽  
Generation Rate ◽  
Heat Generation Rate ◽  
Clinical Patient ◽  
Tumor Pathology

Abstract Cancer is one of the most debilitating diseases in the world, affecting over 9.6 million people worldwide every year. Breast cancer remains the second largest cause of death in women. Despite major advances in treatment, over 40,920 women died of breast cancer in 2018 in the United States alone. Early detection of abnormal masses can be crucial for diagnosis and dramatically increase survival. Current screening techniques have varying accuracy and perform poorly when used on heterogeneously and extremely dense breast tissue. Infrared imaging has the potential to detect growing tumors within the breast based on thermal signatures on the breast surface by imaging temperature gradients induced by blood perfusion and tumor metabolic activity. Using clinical patient images, previous methods to estimate tumor properties involve an iterative algorithm to estimate the tumor position and diameter. The details from the MRI are used in estimating the volumetric heat generation rate. This is compared with the published values and the reasons for differences are investigated. The tumor pathology is used in estimating the expected growth rate and compared with the predicted values. The correlation between the tumor characteristics and heat generation rate is fundamental information that is needed in accurately predicting the tumor size and location.

scholarly journals Comparative Analysis of the Thermal Insulation of Multi-Layer Thermal Inserts in a Protective Jacket

Materials ◽  
2020 ◽  
Vol 13 (12) ◽  
pp. 2672
Author(s):  
Dubravko Rogale ◽  
Goran Majstorović ◽  
Snježana Firšt Rogale
Keyword(s):  
Thermal Properties ◽  
Comparative Analysis ◽  
Thermal Insulation ◽  
Professional Services ◽  
Cold Weather ◽  
Complete Analysis ◽  
Thermal Manikin ◽  
Scientific Methods ◽  
Textile Materials ◽  
Measurement Results

This paper presents the measurement results of the thermal insulation of the outer shell, thermal inserts, and clothing systems, as well as a comparative analysis of the thermal insulation of multi-layer thermal inserts in a thermal jacket intended for professional services in cold weather. Detachable thermal inserts are made of double-faced, diamond-shaped quilted lining with different masses per unit area, and together with the jacket, they form clothing systems with different thermal properties. Tests of the thermal properties of clothing were performed on a thermal manikin. They showed that an increase in the mass of thermal insulation textile materials contributes to an increase in the thermal insulation properties of clothing and are insufficient for a complete analysis of the thermal properties of clothing. Therefore, for the first time, three new parameters of integration efficiency of the thermal insert, thermal insulation efficiency parameters, and efficiency parameters of the integration of the textile material integrated into the clothing system were introduced. Based on these parameters, it is possible to perform an effective and accurate comparative analysis of the thermal insulation of multi-layer thermal inserts in clothing. This makes it possible to apply exact scientific methods largely in the technical design of the thermal properties of integrated textile materials, instead of experience-based methods as in the past.

scholarly journals Stem Water Content for Crape Myrtle in Response to Drought, Cold, and Disease Stress

2020 ◽  
Vol 2020 ◽  
pp. 1-10
Author(s):  
Chao Gao ◽  
Yue Zhao ◽  
Yandong Zhao
Keyword(s):  
Drought Stress ◽  
Cold Stress ◽  
Water Content ◽  
Negative Correlation ◽  
Correlation Coefficients ◽  
Cold Weather ◽  
Positive Correlation ◽  
Health Level ◽  
Diurnal Range ◽  
Stem Water

The abiotic and biotic stresses including drought, cold, and disease stress are linked by the fact that they all decrease the availability of water to plant cells. In previous studies, some physiological factors related with plant water status, such as stem sap flow, leaf transpiration rate, and water potential, were used to assess the effects of these stresses on plants. But there are few studies about the effects of these stresses on stem water content (StWC) which can be measured by a novel SWR sensor. In this study, crape myrtle was selected as an experimental subject and its StWC was observed in four experiments including no stress, drought, cold, and disease stress. Before conducting stress experiments, the StWC and environmental and physiological parameters were synchronously monitored under unstressed conditions on a typical day in summer. In the experiment of drought stress, the StWC was monitored under different gradients of soil moisture. In the experiment of cold stress, the StWC was monitored in warm and cold weather, respectively. In the experiment of disease stress, the StWC was monitored under different frequencies of disease treatment. The results showed that the correlation coefficients between StWC and PAR and VPD were larger than 0.5 and the correlation coefficients between StWC and Pn, Tr, Gs, and Ci were larger than 0.8 under no stress. The diurnal mean of StWC decreased firstly, then remained stable for a period of time, and eventually continued to fall under drought stress. On the whole, there was a negative correlation between the diurnal mean of StWC and the degree of drought stress. The StWC showed opposite diurnal variation rules in warm and cold weather. There was a positive correlation between the diurnal range of StWC and the degree of cold stress. The diurnal minimum, maximum, and mean of StWC showed a positive correlation with the health level of plants and the diurnal range of StWC showed a negative correlation with the health level of plants. In conclusion, the StWC can be used as a qualitative evaluation index of the degree of the three types of stress.

Sign in / Sign up

Export Citation Format

Share Document