scholarly journals A Tunable Wideband Frequency Synthesizer Using LC-VCO and Mixer for Reconfigurable Radio Transceivers

2011 ◽  
Vol 2011 ◽  
pp. 1-7 ◽  
Author(s):  
Yusaku Ito ◽  
Kenichi Okada ◽  
Kazuya Masu

This paper proposes a novel wideband LC-based voltage-controlled oscillator (VCO) for multistandard transceivers. The proposed VCO has a core LC-VCO and a tuning-range extension circuit, which consists of switches, a mixer, dividers, and variable gain combiners with a spurious rejection technique. The experimental results exhibit 0.98 to 6.6 GHz continuous frequency tuning with −206 dBc/Hz of FoMT, which is fabricated by using a 0.18 μm CMOS process. The frequency tuning range (FTR) is 149%, and the chip area is 800 μm × 540 μm.

Electronics ◽  
2021 ◽  
Vol 10 (8) ◽  
pp. 889
Author(s):  
Xiaoying Deng ◽  
Peiqi Tan

An ultra-low-power K-band LC-VCO (voltage-controlled oscillator) with a wide tuning range is proposed in this paper. Based on the current-reuse topology, a dynamic back-gate-biasing technique is utilized to reduce power consumption and increase tuning range. With this technique, small dimension cross-coupled pairs are allowed, reducing parasitic capacitors and power consumption. Implemented in SMIC 55 nm 1P7M CMOS process, the proposed VCO achieves a frequency tuning range of 19.1% from 22.2 GHz to 26.9 GHz, consuming only 1.9 mW–2.1 mW from 1.2 V supply and occupying a core area of 0.043 mm2. The phase noise ranges from −107.1 dBC/HZ to −101.9 dBc/Hz at 1 MHz offset over the whole tuning range, while the total harmonic distortion (THD) and output power achieve −40.6 dB and −2.9 dBm, respectively.


2012 ◽  
Vol 256-259 ◽  
pp. 2373-2378
Author(s):  
Wu Shiung Feng ◽  
Chin I Yeh ◽  
Ho Hsin Li ◽  
Cheng Ming Tsao

A wide-tuning range voltage-controlled oscillator (VCO) with adjustable ground-plate inductor for ultra-wide band (UWB) application is presented in this paper. The VCO was implemented by standard 90nm CMOS process at 1.2V supply voltage and power consumption of 6mW. The tuning range from 13.3 GHz to 15.6 GHz with phase noise between -99.98 and -115dBc/Hz@1MHz is obtained. The output power is around -8.7 to -9.6dBm and chip area of 0.77x0.62mm2.


Electronics ◽  
2021 ◽  
Vol 10 (2) ◽  
pp. 109
Author(s):  
Youming Zhang ◽  
Xusheng Tang ◽  
Zhennan Wei ◽  
Kaiye Bao ◽  
Nan Jiang

This paper presents a Ku-band fractional-N frequency synthesizer with adaptive loop bandwidth control (ALBC) to speed up the lock settling process and meanwhile ensure better phase noise and spur performance. The theoretical analysis and circuits implementation are discussed in detail. Other key modules of the frequency synthesizer such as broadband voltage-controlled oscillator (VCO) with auto frequency calibration (AFC) and programable frequency divider/charge pump/loop filter are designed for integrity and flexible configuration. The proposed frequency synthesizer is fabricated in 0.13 μm CMOS technology occupying 1.14 × 1.18 mm2 area including ESD/IOs and pads, and the area of the ALBC is only 55 × 76 μm2. The out frequency can cover from 11.37 GHz to 14.8 GHz with a frequency tuning range (FTR) of 26.2%. The phase noise is −112.5 dBc/Hz @ 1 MHz and −122.4 dBc/Hz @ 3 MHz at 13 GHz carrier frequency. Thanks to the proposed ALBC, the lock-time can be shortened by about 30% from about 36 μs to 24 μs. The chip area and power consumption of the proposed ALBC technology are slight, but the beneficial effect is significant.


2019 ◽  
Vol 28 (07) ◽  
pp. 1950122 ◽  
Author(s):  
Imen Ghorbel ◽  
Fayrouz Haddad ◽  
Wenceslas Rahajandraibe ◽  
Mourad Loulou

A design methodology of CMOS LC voltage-controlled oscillator (VCO) is proposed in this paper. The relation between components and specifications of the LC-VCO is studied to easily identify its design trade-offs. This methodology has been applied to design ultra-low-power LC-VCOs for different frequency bands. An LC-VCO based on the current reuse technique has been realized with the proposed methodology in 0.13[Formula: see text][Formula: see text]m CMOS process. Measurements present an ultra-low power consumption of only 262[Formula: see text][Formula: see text]W drawn from 1[Formula: see text]V supply voltage. The measured frequency tuning range is about 10% between 2.179[Formula: see text]GHz and 2.409[Formula: see text]GHz. The post-layout simulation presents a phase noise (PN) of [Formula: see text][Formula: see text]dBc/Hz, while the measured PN is [Formula: see text][Formula: see text]dBc/Hz.


Electronics ◽  
2020 ◽  
Vol 9 (6) ◽  
pp. 935 ◽  
Author(s):  
Arash Hejazi ◽  
YoungGun Pu ◽  
Kang-Yoon Lee

This paper presents a wide-range and low phase noise mm-Wave Voltage Controlled Oscillator (VCO) based on the transconductance linearization technique. The proposed technique eliminates the deep triode region of the active part of the VCO, and lowers the noise introduced by the gm-cell. The switch sizes inside the switched capacitor bank of the VCO are optimized to minimize the resistance of the switches while keeping the wide tuning range. A new layout technique shortens the routing of the VCO outputs, and lowers the parasitic inductance and resistance of the VCO routing. The presented method prevents the reduction of the quality factor of the tank due to the long routing. The proposed VCO achieves a discrete frequency tuning range, of 14 GHz to 18 GHz, through a linear coarse and middle switched capacitor array, and offers superior phase noise performance compared to recent state-of-the-art VCO architectures. The design is implemented in a 45 nm CMOS process and occupies a layout area (including output buffers) of 0.14 mm2. The power consumption of the VCO core is 24 mW from the power supply of 0.8 V. The post-layout simulation result shows the VCO achieves the phase noise performances of −87.2 dBc/Hz and −113 dBc/Hz, at 100 kHz and 1 MHz offset frequencies from the carrier frequency of 14 GHz, respectively. In an 18 GHz carrier frequency, the results are −87.4 dBc/Hz and −110 dBc/Hz, accordingly.


Author(s):  
Abhishek Kumar

In a modern communication system, voltage-controlled oscillator (VCO) acts as a basic building block for frequency generation. VCO with LC tank is preferred with passive inductor and varactor in radio frequency. Practical tuning range of VCO is low and unsuitable for wideband application. Switched capacitor and inductor can widen but at cost of chip area and complex system architecture. To overcome it, an equivalent circuit of the inductor is created. In this work, inductor-less VCO is implemented with CMOS 90nm technology that has center frequency 40GHz and frequency tuning range 37.7GHz to 41.9GHz.


Electronics ◽  
2020 ◽  
Vol 9 (8) ◽  
pp. 1290
Author(s):  
Jeong-Yun Lee ◽  
Gwang Sub Kim ◽  
Goo-Han Ko ◽  
Kwang-Il Oh ◽  
Jae Gyeong Park ◽  
...  

This paper proposes a new structure of 24-GHz class-C voltage-controlled oscillator (VCO) using an auto-adaptive bias technique. The VCO in this paper uses a digitally controlled circuit to eliminate the possibility of start-up failure that a class-C structure can have and has low phase noise and a wide frequency range. To expand the frequency tuning range, a 3-bit cap-bank is used and a triple-coupled transformer is used as the core inductor. The proposed class-C VCO implements a 65-nm RF CMOS process. It has a phase noise performance of −105 dBc/Hz or less at 1-MHz offset frequency and the output frequency range is from 22.8 GHz to 27.3 GHz, which consumes 8.3–10.6 mW of power. The figure-of-merit with tuning range (FoMT) of this design reached 191.1 dBc/Hz.


Author(s):  
Shitesh Tiwari ◽  
Sumant Katiyal ◽  
Parag Parandkar

Voltage Controlled Oscillator (VCO) is an integral component of most of the receivers such as GSM, GPS etc. As name indicates, oscillation is controlled by varying the voltage at the capacitor of LC tank. By varying the voltage, VCO can generate variable frequency of oscillation. Different VCO Parameters are contrasted on the basis of phase noise, tuning range, power consumption and FOM. Out of these phase noise is dependent on quality factor, power consumption, oscillation frequency and current. So, design of LC VCO at low power, low phase noise can be obtained with low bias current at low voltage.  Nanosize transistors are also contributes towards low phase noise. This paper demonstrates the design of low phase noise LC VCO with 4.89 GHz tuning range from 7.33-11.22 GHz with center frequency at 7 GHz. The design uses 32nm technology with tuning voltage of 0-1.2 V. A very effective Phase noise of -114 dBc / Hz is obtained with FOM of -181 dBc/Hz. The proposed work has been compared with five peer LC VCO designs working at higher feature sizes and outcome of this performance comparison dictates that the proposed work working at better 32 nm technology outperformed amongst others in terms of achieving low Tuning voltage and moderate FoM, overshadowed by a little expense of power dissipation. 


Author(s):  
Titus Oyedokun ◽  
Riana H. Geschke ◽  
Tinus Stander

Abstract We present a tunable planar groove gap waveguide (PGGWG) resonant cavity at Ka-band. The cavity demonstrates varactor loading and biasing without bridging wires or annular rings, as commonly is required in conventional substrate-integrated waveguide (SIW) resonant cavities. A detailed co-simulation strategy is also presented, with indicative parametric tuning data. Measured results indicate a 4.48% continuous frequency tuning range of 32.52–33.98 GHz and a Qu tuning range of 63–85, corresponding to the DC bias voltages of 0–16 V. Discrepancies between simulated and measured results are analyzed, and traced to process variation in the multi-layer printed circuit board stack, as well as unaccounted varactor parasitics and surface roughness.


2018 ◽  
Vol 27 (10) ◽  
pp. 1850158 ◽  
Author(s):  
Rekha Yadav ◽  
Pawan Kumar Dahiya ◽  
Rajesh Mishra

In this paper, a novel method to realize LC Voltage-Controlled-Oscillator (LC-VCO) operating at 76.2–76.7[Formula: see text]GHz frequency band for microwave RFIC component is presented. The model of cross-coupled differential LC-VCO is designed in 45[Formula: see text]nm technology using Complementary Metal Oxide Semiconductor (CMOS) process for Frequency Modulated Carrier Wave (FMCW) automotive radar sensors and RF transceivers application. The impact of VDD, control voltage and temperature variation on frequency shift, phase noise, and output power has been analyzed to optimize the trade-off between frequency, phase noise, and power requirement. The results depict that LC-VCO dissipates 10.45[Formula: see text]mW power at an operating voltage of 1.5[Formula: see text]V. The phase noise has been observed to be [Formula: see text]90[Formula: see text]dBc/Hz at 1[Formula: see text]MHz offset at 76[Formula: see text]GHz carrier frequency. The estimated layout area of IC is [Formula: see text]m2. The result shows the edge of the design over existing techniques.


Sign in / Sign up

Export Citation Format

Share Document