scholarly journals Valorization of Agroindustrial Wastes as Biosorbent for the Removal of Textile Dyes from Aqueous Solutions

2012 ◽  
Vol 2012 ◽  
pp. 1-9 ◽  
Author(s):  
Elsa Contreras ◽  
Luisa Sepúlveda ◽  
Carolyn Palma

The goal is to determinate the technical feasibility of using agroindustrial wastes for adsorption of dyes. The pHpzcof Brewer’s spent grains and Orange peel is 5.3 and 3.5, respectively. The equilibrium isotherms of Basic Blue 41, Reactiive Black 5, and Acid Black 1 were carried out without pHs control which ranging between 4 and 5.5. The equilibrium concentrations for both adsorbents were fitted by the Freundlich and Langmuir models. The maximum adsorption capacity measured for Basic Blue 41, Reactive Black 5, and Acid Black 1 was 32.4, 22.3, and 19.8 mg g-1for Brewer’s spent grains; and 157, 62.6, and 45.5 for orange peel, respectively. The kinetic of process was fitted by the model of pseudo-second order. The constant rate for orange peel decreased to extend the initial concentration of dye increased, obtaining 4.08 * 10−3−0.6 * 10−3(Basic Blue 41), 2.98 * 10−3−0.36 * 10−3(Acid Black 1), and 3.40 * 10−3−0.46 * 10−3 g mg−1 min−1(Reactive Black 5). The best removal efficiency was obtained in orange peel with values started from 63% to 20%. Consequently, according the results obtained there are two positive effects, the reuse of agricultural wastes and its use as low-cost adsorbent of the dyes.

2018 ◽  
Vol 77 (5) ◽  
pp. 1313-1323 ◽  
Author(s):  
Jianjun Zhou ◽  
Xionghui Ji ◽  
Xiaohui Zhou ◽  
Jialin Ren ◽  
Yaochi Liu

Abstract A novel magnetic bio-adsorbent (MCIA) was developed, characterized and tested for its Cd(II) removal from aqueous solution. MCIA could be easily separated from the solution after equilibrium adsorption due to its super-paramagnetic property. The functional and magnetic bio-material was an attractive adsorbent for the removal of Cd(II) from aqueous solution owing to the abundant adsorption sites, amino-group and oxygen-containing groups on the surface of Cyclosorus interruptus. The experimental results indicated that the MCIA exhibited excellent adsorption ability and the adsorption process was spontaneous and endothermic. The adsorption isotherm was consistent with the Langmuir model. The adsorption kinetic fitted the pseudo-second-order model very well. The maximum adsorption capacity of Cd(II) onto MCIA was 40.8, 49.4, 54.6 and 56.6 mg/g at 293, 303, 313 and 323 K, respectively. And the MCIA exhibited an excellent reusability and impressive regeneration. Therefore, MCIA could serve as a sustainable, efficient and low-cost magnetic adsorbent for Cd(II) removal from aqueous solution.


2017 ◽  
Vol 36 (1-2) ◽  
pp. 372-392 ◽  
Author(s):  
Borano Te ◽  
Boonchai Wichitsathian ◽  
Chatpet Yossapol ◽  
Watcharapol Wonglertarak

In this study, natural clay, iron oxide, and iron powder were combined to develop low-cost iron mixed porous pellet adsorbent for arsenate and arsenite removal from aqueous solution in batch experiments. The augmented simplex centroid mixture design was applied to obtain the optimum proportion of each constituent. Higher correlation coefficient of the models (R2 > 0.95), good distribution of residuals, and lower values of p value (<0.05) indicated that the method is suitable for determining the optimum mixture proportion. Extensive decrease of both arsenate and arsenite adsorption occurred in the alkaline condition (pH > 9). Kinetic and isotherm experimental data of both arsenate and arsenite were well described by the pseudo-second order and Sips models, respectively. The maximum adsorption capacity of arsenate and arsenite derived from Sips model were 13.33 and 19.06 mg/g, respectively. The separation and heterogeneity factors showed that both arsenate and arsenite were favorably adsorbed. Among coexisting anions, phosphate significantly showed negative effect on the adsorption of either arsenate or arsenite. The adsorbent could be effectively reused for several times after its regeneration and was considered as non-hazardous material after adsorption.


2016 ◽  
Vol 2016 ◽  
pp. 1-11 ◽  
Author(s):  
Ankur Gupta ◽  
Chandrajit Balomajumder

Fe modified rice husk was prepared as a low cost biosorbent for the removal of Cr(VI) and phenol both singly and in combination from single and binary simulated synthetic waste water. Rice husk was modified by treating with FeSO4·7H2O. The results showed that impregnation of iron onto the surface of rice husk improved the adsorption capability of both Cr(VI) and phenol. The effects of process parameters for multicomponent system such as pH, adsorbent dose, and contact time onto the percentage removal of both Cr(VI) and phenol were investigated. The experimental data for the adsorption of both Cr(VI) and phenol onto the surface of Fe modified rice husk applied to various kinetic and adsorption isotherm models. Multicomponent isotherm models such as Nonmodified Langmuir, Modified Langmuir, Extended Langmuir, Extended Freundlich, Competitive Nonmodified Redlich Peterson, Competitive Modified Redlich Peterson were applied. The results show that Extended Freundlich model best described the experimental data for both Cr(VI) and phenol from binary solution. Pseudo second-order model agreed well with Cr(VI) while pseudo first-order model agreed well with phenol. Maximum adsorption capacity in synthetic binary solution of Cr(VI) and phenol was found to be 36.3817 mg g−1for Cr(VI) and 6.569 mg g−1for phenol, respectively.


2012 ◽  
Vol 65 (8) ◽  
pp. 1341-1349 ◽  
Author(s):  
Shokooh Sadat Khaloo ◽  
Amir Hossein Matin ◽  
Sahar Sharifi ◽  
Masoumeh Fadaeinia ◽  
Narges Kazempour ◽  
...  

The application of almond shell as a low cost natural adsorbent to remove Hg2+ from aqueous solution was investigated. Batch experiments were carried out to evaluate the adsorption capacity of the material. The chemical and physical parameters such as pH, sorbent amount, initial ion concentration, and contact time were optimized for the maximum uptake of mercury onto the solid surface. Adsorption isotherms were expressed by Langmuir and Freundlich adsorption models, and the experimental data were found to fit the Langmuir model rather than the Freundlich. The maximum adsorption capacity obtained from the Langmuir isotherm was 135.13 mg/g. A kinetic study was carried out with pseudo-first-order and pseudo-second-order reaction equations and it was found that the Hg2+ uptake process followed the pseudo-second-order rate expression. The thermodynamic values, ΔG0, ΔH0 and ΔS0, indicated that adsorption was an endothermic and spontaneous process. The potential of this material for mercury elimination was demonstrated by efficient Hg2+ removal from a synthetic effluent.


2016 ◽  
Vol 12 (1) ◽  
pp. 61
Author(s):  
Arenst Andreas Arie ◽  
Emerentina Maerilla Puspaningrum ◽  
Henky Muljana

<p class="Abstract">Low-cost and environmental friendly activated carbons were synthesized from orange peel waste by carbonization followed by activation process using supercritical carbon dioxide. The carbonization process of orange peel waste was conducted in the electrical furnace at temperature of 800 °C for 2 h. Activation process of the impregnated orange peel was carried out in the tubular furnace for 1 h at activation temperature of 140 °C and pressure variation of 80, 125 and 170 bar. Activated carbon with highest surface area of 262.173 m<sup>2</sup>/g was obtained by co<sub>2</sub> pressure of 125 bar. The activated carbons were then utilized as adsorbents for removal of methylene blue (MB) from aqueous solution. The batch adsorption study was carried out by varying the initial concentration of mb solution (2, 4, 6, 8 and 10 ppm). Experimental results showed that the adsorption kinetic of mb fitted the pseudo-second-order rate equation, where as for the adsorption isotherm model followed two models i.e. The dubinin- radushkevich and freundlich model. The adsorption mechanism was found to be governed by the intraparticle and surface diffusion mechanism.</p>


2021 ◽  
pp. 1-12
Author(s):  
Raafia Najam ◽  
Syed Muzaffar Ali Andrabi

Sawdust of willow has been investigated as an adsorbent for the removal of Ni(II), and Cd(II) ions from aqueous solution. Since willow tree is widely grown in almost all parts of Kashmir, it can be a common most easily available, sustainable, low cost adsorbent for the treatment of wastewaters in this part of the world where growing industrialization is affecting water quality like elsewhere in the world. Therefore, it is worthwhile to investigate the potential of sawdust of willow tree as an adsorbent for the removal of Ni(II) and Cd(II) ions from aqueous solution as a first step. Batch experiments were conducted to study the effect of some parameters such as contact time, initial concentration of metal ions, solution pH and temperature. Langmuir and Freundlich models were employed for the mechanistic analysis of experimental data obtained. Results reveal that in our system adsorption follows the Langmuir isotherm. The maximum adsorption capacity of Ni(II) and Cd(II) were found to be 7.98 and 7.11 mg/g respectively at optimum conditions. The pseudo-first-order and pseudo-second-order models were employed for kinetic analysis of adsorption process. The adsorption process follows pseudo-second-order kinetics. The efficacy of the adsorbent in the treatment of effluent from fertilizer factory has been investigated and the results have been found encouraging.


Gels ◽  
2021 ◽  
Vol 7 (4) ◽  
pp. 178
Author(s):  
Serap Sezen ◽  
Vijay Kumar Thakur ◽  
Mehmet Murat Ozmen

Currently, macroporous hydrogels have been receiving attention in wastewater treatment due to their unique structures. As a natural polymer, alginate is used to remove cationic dyes due to its sustainable features such as abundance, low cost, processability, and being environmentally friendly. Herein, alginate/montmorillonite composite macroporous hydrogels (cryogels) with high porosity, mechanical elasticity, and high adsorption yield for methylene blue (MB) were generated by the one-step cryogelation technique. These cryogels were synthesized by adding montmorillonite into gel precursor, followed by chemical cross-linking employing carbodiimide chemistry in a frozen state. The as-prepared adsorbents were analyzed by FT-IR, SEM, gel fraction, swelling, uniaxial compression, and MB adsorption tests. The results indicated that alginate/montmorillonite cryogels exhibited high gelation yield (up to 80%), colossal water uptake capacity, elasticity, and effective dye adsorption capacity (93.7%). Maximum adsorption capacity against MB was 559.94 mg g−1 by linear regression of Langmuir model onto experimental data. The Pseudo-Second-Order model was fitted better onto kinetic data compared to the Pseudo-First-Order model. Improved porosity and mechanical elasticity yielding enhanced dye removal capacity make them highly potential alternative adsorbents compared to available alginate/montmorillonite materials for MB removal.


Author(s):  
Thaisa Caroline Andrade Siqueira ◽  
Isabella Zanette da Silva ◽  
Andressa Jenifer Rubio ◽  
Rosângela Bergamasco ◽  
Francielli Gasparotto ◽  
...  

Adsorption in biomass has proven to be a cost-effective option for treatment of wastewater containing dyes and other pollutants, as it is a simple and low cost technique and does not require high initial investments. The present work aimed to study the adsorption of methylene blue dye (MB) using sugarcane bagasse (SCB). The biomass was characterized by scanning electron microscopy (SEM). Adsorption studies were conducted batchwise. Kinetics, adsorption isotherms, and thermodynamics were studied. The results showed that SCB presented a maximum adsorption capacity of 9.41 mg g−1 at 45 °C after 24 h of contact time. Adsorption kinetics data better fitted the pseudo-second order model, indicating a chemical process was involved. The Sips’s three-parameter isotherm model was better for adjusting the data obtained for the adsorption isotherms, indicating a heterogeneous adsorption process. The process showed to be endothermic, spontaneous, and feasible. Therefore, it was concluded that SCB presented as a potential biosorbent material for the treatment of MB-contaminated waters.


2018 ◽  
Vol 10 (11) ◽  
pp. 4250 ◽  
Author(s):  
Shuang Xu ◽  
Weiguang Yu ◽  
Sen Liu ◽  
Congying Xu ◽  
Jihui Li ◽  
...  

A low-cost biochar was prepared through slow pyrolysis of banana pseudostem biowaste at different temperatures, and characterized by surface area and porosity analysis, scanning electron microscopy (SEM), Fourier-transform infrared (FTIR) spectroscopy, and X-ray photoelectron spectroscopy (XPS). It was shown that the biochar prepared at low pyrolysis temperature was rich in oxygen-containing groups on the surface. Adsorption experiments revealed that the biochar prepared at 300 °C (BB300) was the best adsorbent for Cr(VI) with 125.44 mg/g maximum adsorption capacity at pH 2 and 25 °C. All the adsorption processes were well described by pseudo-second-order and Langmuir models, indicating a monolayer chemiadsorption. Furthermore, it was demonstrated that adsorption of Cr(VI) was mainly attributed to reduction of Cr(VI) to Cr(III) followed by ion exchange and complexation with the biochar.


2016 ◽  
Vol 12 (1) ◽  
Author(s):  
Arenst Andreas Arie

<p class="Abstract">Low-cost and environmental friendly activated carbons were synthesized from orange peel waste by carbonization followed by activation process using supercritical carbon dioxide. The carbonization process of orange peel waste was conducted in the electrical furnace at temperature of 800 °C for 2 h. Activation process of the impregnated orange peel was carried out in the tubular furnace for 1 h at activation temperature of 140 °C and pressure variation of 80, 125 and 170 bar. Activated carbon with highest surface area of 262.173 m<sup>2</sup>/g was obtained by co<sub>2</sub> pressure of 125 bar. The activated carbons were then utilized as adsorbents for removal of methylene blue (MB) from aqueous solution. The batch adsorption study was carried out by varying the initial concentration of mb solution (2, 4, 6, 8 and 10 ppm). Experimental results showed that the adsorption kinetic of mb fitted the pseudo-second-order rate equation, whereas for the adsorption isotherm model followed two models i.e. The dubinin- radushkevich and freundlich model. The adsorption mechanism was found to be governed by the intraparticle and surface diffusion mechanism.</p>


Sign in / Sign up

Export Citation Format

Share Document