scholarly journals Mechanical Properties and Morphological Characterization of PLA/Chitosan/Epoxidized Natural Rubber Composites

2013 ◽  
Vol 2013 ◽  
pp. 1-7 ◽  
Author(s):  
Zainoha Zakaria ◽  
Md. Saiful Islam ◽  
Azman Hassan ◽  
M. K. Mohamad Haafiz ◽  
Reza Arjmandi ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Natural Rubber ◽  
Morphological Characteristics ◽  
Tensile Modulus ◽  
Phase Segregation ◽  
Morphological Characterization ◽  
Attractive Interaction ◽  
Poly Lactic Acid ◽  
Good Dispersion

Poly (lactic acid) (PLA)/chitosan (CS) natural polymer/epoxidised natural rubber (ENR) composites were successfully prepared through a solution casting method. The morphological characteristics of fabricated composites were investigated by scanning electron microscopy (SEM) and optical microscopy. The microstructure of PLA/ENR was significantly altered with the addition of CS. SEM analysis of composites fractured surfaces revealed smooth and homogeneous texture and good dispersion of CS. However for 15 wt% CS composites, the phase segregation and poor adhesion between the polymers were observed. Fourier transform infrared spectroscopy revealed some levels of attractive interaction between CS, PLA, and ENR in the composites. The mechanical properties of composites in terms of tensile strength and tensile modulus were significantly improved with the addition of CS into the matrix while the percent elongation at break decreased. The tensile strength increased up to 5 wt% CS loading for both PLA/CS and PLA/ENR/CS and thereafter decreased while Young’s modulus increased up to 10 wt%. However, when the CS content was increased to 15 wt%, the tensile strength and tensile modulus were slightly decreased. These improvements were attributed to good dispersion of CS at the optimum filler levels and attractive interaction between the composites components.

Effect of Aging on Mechanical Properties of Natural Rubber Latex Products Filled with Alkanolamide-Modified Cassava Peel Waste Powder (CPWP)

2015 ◽  
Vol 1123 ◽  
pp. 387-390 ◽  
Author(s):  
Hamidah Harahap ◽  
Adrian Hartanto ◽  
Kelvin Hadinatan ◽  
Indra Surya ◽  
Baharin Azahari
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Natural Rubber ◽  
Natural Rubber Latex ◽  
Tensile Modulus ◽  
Rubber Latex ◽  
Elongation At Break ◽  
Hot Air ◽  
Before And After ◽  
Cassava Peel

The effect of aging on mechanical properties of natural rubber latex (NRL) products filled with alkanolamide-modified cassava peel waste powder (CPWP) was studied. CPWP used as fillers was prepared by milling and sieving it until the size of 100 mesh. The powder then was dispersed in a suspension containing water and alkanolamide in order to modify the prepared powders. The dispersion system of 10 pphr (part per hundred rubber) then was added into NRL matrix followed by pre-vulcanization at 70°C for 10 minutes. The NRL compound then were casted into films by coagulant dipping method then dried at 120°C for 10 minutes. Afterwards, the films were allowed to cool at room temperature for 24 hours before being aged in a circulation of hot air for 24 hours at 70°C. The properties such as tensile strength, tensile modulus, and elongation at break were evaluated between the aged samples and the unaged samples. From this study, it showed that the aged films have increasing value of tensile strength and tensile modulus while the value of elongation at break decreases. These datas are supported by Scanning Electron Microscope (SEM) micrographs which indicate that the change of morphology in NRL films occurs before and after aging.

Cellular Bi2O3/natural rubber composites for light-weight and lead-free gamma-shielding materials and their properties under gamma irradiation

2021 ◽  
pp. 0021955X2199735
Author(s):  
Phakamat Limarun ◽  
Teerasak Markpin ◽  
Narongrit Sombatsompop ◽  
Ekachai Wimolmala ◽  
Kiadtisak Saenboonruang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Natural Rubber ◽  
Gamma Irradiation ◽  
Attenuation Coefficient ◽  
Tensile Modulus ◽  
Lead Free ◽  
Morphological Properties ◽  
Light Weight ◽  
Elongation At Break

This work investigated the effects of a radiation-protective filler, namely bismuth oxide (Bi2O3), and blowing agents, namely azodicarbonamide (ADC) and oxy-bis (benzene sulfonyl) hydrazide (OBSH), on gamma attenuation and the mechanical, physical, and morphological properties of cellular natural rubber (NR) composites for potential use as light-weight and lead-free gamma-shielding materials. The contents of Bi2O3 were varied from 100 to 300 and 500 parts per hundred of rubber by weight (phr) and the contents of ADC or OBSH were varied from 0 to 8 and 16 phr. The results indicated that the addition of Bi2O3 enhanced the overall gamma-shielding ability, density, tensile modulus, and hardness (Shore OO), but lowered the tensile strength and elongation at break. On the other hand, the addition of ADC or OBSH resulted in decreases in the density, linear attenuation coefficient ( μ), and overall tensile properties but an increase in the mass attenuation coefficient ( μm), with ADC producing better mechanical properties than samples with OBSH. In addition, investigations on the properties of the cellular Bi2O3/NR composites under additional 35 kGy and 70 kGy gamma irradiation revealed that the irradiated samples had increased density, tensile modulus, and hardness (Shore OO), but decreased tensile strength, elongation at break, and μm after such ageing. In conclusion, the overall results suggested that the developed cellular Bi2O3/NR composites not only had efficient and promising gamma-shielding and mechanical properties but also offered comfort and light-weight to users, which could potentially reduce discomforts caused by wearing heavier conventional radiation-protective equipment.

Mechanical Properties of Bamboo Charcoal (BC)/Poly(Lactic) Acid (PLA) Composites

2019 ◽  
Vol 801 ◽  
pp. 121-126
Author(s):  
Rapeeporn Srisuk ◽  
Laongdaw Techawinyutham ◽  
Wantana Koetniyom ◽  
Rapeephun Dangtungee
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Lactic Acid ◽  
Shear Viscosity ◽  
Tensile Modulus ◽  
Poly Lactic Acid ◽  
Bamboo Charcoal ◽  
Elongation At Break ◽  
The Matrix

The influence of bamboo charcoal (BC) in Poly (lactic) acid (PLA) matrix as masterbatch was studied on mechanical 40:60, 50:50 and 60:40 of masterbatch. BC MBs were diluted at 1 phr, 3 phr, and 5 phr. BC showed even distribution in PLA matrix; however,, it decreased compatibility in the matrix. The infusion of BC in PLA matrix enhanced the tensile modulus; however, there was a reduction in the tensile strength and the elongation at break. It could also be ascertained that there is no signification difference in the hardness of BC/PLA composites compared with neat PLA. The addition of BC slightly decreased shear viscosity of the composites. The optimal BC content in the composites was found to be 2.82wt.% (5 phr 60:40).

scholarly journals Mechanical Properties of Poly (lactic acid) Composites Reinforced with CaCO3 Eggshell Based Fillers

MRS Advances ◽  
2017 ◽  
Vol 2 (47) ◽  
pp. 2545-2550 ◽  
Author(s):  
Nicholas G. Betancourt ◽  
Duncan E. Cree
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Lactic Acid ◽  
Water Absorption ◽  
Filler Content ◽  
Tensile Modulus ◽  
Charpy Impact ◽  
Filler Loading ◽  
Poly Lactic Acid ◽  
Particle Sizes

ABSTRACTPoly (lactic acid) (PLA) bioplastics are recyclable and biodegradable thermoplastics. They are derived from environmentally friendly sources such as potatoes, cornstarch and sugarcane. However, PLA is inherently brittle with low impact strength. The goal of this study is to improve mechanical properties of PLA by the addition of calcium carbonate (CaCO3) fillers. PLA composites were prepared by injection molding conventional limestone (LS) and white chicken eggshell (WES) powders with particle sizes of 63 μm and 32 μm in amounts of 5 wt. %, 10 wt. % and 20 wt. %. Mechanical properties such as, tensile strength, tensile modulus, and Charpy impact strengths were investigated. These three properties were evaluated and the results statistically analyzed using ANOVA F-test. For both particle sizes, the tensile strength decreased as the filler content increased, but was highest for a filler loading of 5 wt. %. In general, the 32 μm powder fillers had better tensile strengths than 63 μm sized fillers. The tensile modulus increased with filler content and was highest at 20 wt. % for both particle sizes. The LS/PLA composites had better toughness than the WES/PLA composites. The particle filler morphology and fractured surfaces were observed by scanning electron microscopy (SEM) and determined to have well dispersed particles with smooth fractured surfaces. Water absorption behavior of PLA/CaCO3 composites were studied by immersion in distilled water at room temperature for 56 days. Virgin PLA absorbed the least amount of water while the water absorption of CaCO3 composites were a function of powder type and content.

Study on the Properties of Poly(lactic acid)/Starch/Chitosan Blended Materials

2011 ◽  
Vol 391-392 ◽  
pp. 530-534
Author(s):  
Peng Liu ◽  
Cai Qin Gu ◽  
Qing Zhu Zeng
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Thermal Properties ◽  
Tensile Modulus ◽  
Poly Lactic Acid ◽  
Mechanical And Thermal Properties ◽  
Carbonyl Groups ◽  
Amino Groups ◽  
Molecular Force ◽  
Hydroxy Groups

Former researchers have studied the properties of PLA/starch blended materials, but the influence of chitosan for them has not been studied yet. In this paper, it prepared the blended materials of PLA/starch/chitosan, and studied the compatible, mechanical and thermal properties of them. The results demonstrated that, since chitosan molecules had hydroxy and amino groups, which could form molecular force with the hydroxy groups in starch molecules and the carbonyl groups in PLA molecules respectively, the addition of it would improve the compatibility of PLA and starch. The SEM surface and section photos of blended materials could prove this compatibility, and the mechanical properties of blended materials also certified it. Specifically, with the addition of chitosan, the elongation, tensile modulus and tensile strength were all increase. For thermal properties, the addition of chitosan had no influence on it.

scholarly journals UTILIZATION OF TEA WASTE AS AN ALTERNATIVE FILLER FOR NATURAL RUBBER

2020 ◽  
Vol 82 (4) ◽  
Author(s):  
Nabil Hayeemasae ◽  
Hanafi Ismail
Keyword(s):  
Mechanical Properties ◽  
Natural Rubber ◽  
Tensile Properties ◽  
Morphological Characteristics ◽  
Tensile Modulus ◽  
Curing Time ◽  
Maximum Torque ◽  
Curing Characteristics ◽  
Tea Waste ◽  
Balance Set

Tea leave is considered worthless after being discarded. It frequently dumps to the environment without providing the best solution on it. In this study, tea leave waste (TW) was applied to be used as alternative filler for natural rubber. The study was evaluated through the curing characteristics, tensile properties and the morphology of the composites. The results have shown some interesting findings. As for the curing characteristics, the maximum torque was increased with increasing the TW loadings whereas the scorch and curing time showed the decreasing trend. The tensile modulus was also influenced by the addition of TW which correlated to the maximum torque observed. The extent of mechanical properties depends on the loadings of TW. Considering the amounts of TW, a 10 phr of TW was found to be a content of choice for natural rubber. It provided a balance set of properties regardless whether the mechanical properties and morphological characteristics of the natural rubber.

scholarly journals The effect of carbon black on the curing and mechanical properties of natural rubber/ acrylonitrile- butadiene rubber composites

2021 ◽  
Vol 19 (3) ◽  
pp. 194-201
Author(s):  
H. Boukfessa ◽  
B. Bezzazi
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Carbon Black ◽  
Natural Rubber ◽  
Abrasion Resistance ◽  
Tensile Modulus ◽  
Butadiene Rubber ◽  
Rubber Composites ◽  
Acrylonitrile Butadiene Rubber ◽  
Different Content

The present work investigates the effect of the amount of carbon black on curing and mechanical properties such as tensile strength, elongation at break, hardness and abrasion resistance of the natural rubber (NR)/ acrylonitrile-butadiene rubber (NBR) blend. For that purpose, a blend composed of 65% NR and 35% NBR filled with different content of carbon black N330 was used. The curing results indicate that the viscosity and the crosslink density of rubber composites increase and the scorch and curing times decrease with increasing the filler content. Mechanical properties such as tensile modulus and hardness of the CB filled NR/NBR blend were remarkably improved, indicating the inherent reinforcing potential of CB. Regarding tensile strength and abrasion resistance, they increase with the addition of carbon black, up to 50 phr. After that, these properties decrease slightly with filleraddition.

scholarly journals The effect of dynamic vulcanization on the morphological and mechanical properties of the toughened poly (lactic acid)/epoxidized natural rubber

2018 ◽  
Vol 14 (3) ◽  
pp. 348-352 ◽  
Author(s):  
Nur Amira Sahirah Abdullah ◽  
Zurina Mohamad
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Lactic Acid ◽  
Impact Strength ◽  
Natural Rubber ◽  
Crosslinking Agent ◽  
Epoxidized Natural Rubber ◽  
Poly Lactic Acid ◽  
Dynamic Vulcanization ◽  
The Impact

Poly (lactic acid)/epoxidized natural rubber (PLA/ENR) was prepared by using counter-rotating twin-screw extruder. For dynamic vulcanization process, ENR was compounded with 3 phr of N, N’-m-phenylenebismaleimide (HVA-2) as a crosslinking agent. The aim of this study is to determine the effect of unvulcanized and dynamically vulcanized of ENR on the properties of PLA/ENR blend. The blending of PLA with ENR was prepared with the various composition of ENR (0 wt% to 30 wt%). The morphology and mechanical properties of the blends were investigated by using scanning electron microscope (SEM), tensile test, and impact test. The unvulcanized blend produced a co-continuous morphology of PLA and ENR and the dynamically vulcanized blend shows the dispersed ENR rubber particles in PLA continuous matrix.  For both systems, the tensile strength value was dropped with the increasing amount of ENR content. The impact strength of both systems shows the maximum value at 20 wt% of ENR content. However, dynamically vulcanized PLA/ENR blend shows a better tensile strength and impact strength value as compared with unvulcanized blend.

Mechanical Property Improvement of Poly(Butylene Succinate) by Reinforcing with Modified Fumed Silica

2014 ◽  
Vol 1025-1026 ◽  
pp. 215-220 ◽  
Author(s):  
Sasirada Weerasunthorn ◽  
Pranut Potiyaraj
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Flexural Strength ◽  
Fumed Silica ◽  
Tensile Modulus ◽  
Silica Particles ◽  
Melt Mixing ◽  
Butylene Succinate ◽  
Ir Spectrophotometry

Fumed silica particles (SiO2) were directly added into poly (butylene succinate) (PBS) by melt mixing process. The effects of amount of fumed silica particles on mechanical properties of PBS/fumed silica composites, those are tensile strength, tensile modulus, impact strength as well as flexural strength, were investigated. It was found that the mechanical properties decreased with increasing fumed silica loading (0-3 wt%). In order to increase polymer-filler interaction, fumed silica was treated with 3-glycidyloxypropyl trimethoxysilane (GPMS), and its structure was analyzed by FT-IR spectrophotometry. The PBS/modified was found to possess better tensile strength, tensile modulus, impact strength and flexural strength that those of PBS/fumed silica composites.

Effect of Polyethylene Glycol in Nanocellulose/PLA Composites

2019 ◽  
Vol 821 ◽  
pp. 89-95
Author(s):  
Wanasorn Somphol ◽  
Thipjak Na Lampang ◽  
Paweena Prapainainar ◽  
Pongdhorn Sae-Oui ◽  
Surapich Loykulnant ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Lactic Acid ◽  
Polyethylene Glycol ◽  
Aspect Ratio ◽  
Mechanical Performance ◽  
Tensile Modulus ◽  
Poly Lactic Acid ◽  
Solvent Casting ◽  
Casting Method ◽  
Mediated Oxidation

Poly (lactic acid) or PLA was reinforced by nanocellulose and polyethylene glycol (PEG), which were introduced into PLA matrix from 0 to 3 wt.% to enhance compatibility and strength of the PLA. The nanocellulose was prepared by TEMPO-mediated oxidation from microcrystalline cellulose (MCC) powder and characterized by TEM, AFM, and XRD to reveal rod-like shaped nanocellulose with nanosized dimensions, high aspect ratio and high crystallinity. Films of nanocellulose/PEG/PLA nanocomposites were prepared by solvent casting method to evaluate the mechanical performance. It was found that the addition of PEG in nanocellulose-containing PLA films resulted in an increase in tensile modulus with only 1 wt% of PEG, where higher PEG concentrations negatively impacted the tensile strength. Furthermore, the tensile strength and modulus of nanocellulose/PEG/PLA nanocomposites were higher than the PLA/PEG composites due to the existence of nanocellulose chains. Visual traces of crazing were detailed to describe the deformation mechanism.

Sign in / Sign up

Export Citation Format

Share Document