scholarly journals Analysis of Stress Characteristics and the Engineering Application of the Self-Balancing Retaining Wall

2017 ◽  
Vol 2017 ◽  
pp. 1-10 ◽  
Author(s):  
Fei Gan ◽  
XiaoMing Ye ◽  
Ke Yin ◽  
Meilin Li ◽  
Jing Bi
Keyword(s):  
Low Cost ◽  
Retaining Wall ◽  
Economic Effect ◽  
Economic Value ◽  
Engineering Application ◽  
Calculation Model ◽  
The Self ◽  
New Type ◽  
Scope Of Application ◽  
The Cost

A new type of retaining wall, the self-balance retaining wall, is introduced in this paper. Based on the stress analysis, the calculation model and method are advanced about the retaining wall. A comparative analysis related to traditional retaining wall is carried out on stress and cost combining with an actual project. The results show that the idea of using upper gravity retaining wall as the resistance of lower retaining wall is clever and reasonable that the self-balance retaining wall has a very wide scope of application relying on the anchor tensile conditions rarely and that the self-balance retaining wall has a great economic value with low cost. The cost of the self-balance retaining wall is 50% compared with the cantilever pile retaining wall under the same conditions which has a good economic effect and application prospect.

Concurrent Tolerance Design Based on Manufacturing Cost and Quality Loss

2014 ◽  
Vol 687-691 ◽  
pp. 4996-4999
Author(s):  
Zhang Rong
Keyword(s):  
High Performance ◽  
Low Cost ◽  
Engineering Application ◽  
Manufacturing Cost ◽  
Tolerance Design ◽  
Quality Loss ◽  
Product Loss ◽  
Parameterized Model ◽  
The Cost ◽  
Design And Manufacture

With the constraints on manufacturing capacity, the satisfaction of product performance and the cost of manufacture are contradictory, the problem between high-performance and low-cost must be solved at the period of design and manufacture for product. To solve this problem, the product loss model has been analyzed, the parameterized and non-parameterized model of anticipant losses has been researched, with concurrent design, in connection with the product with multiple correlated assembly functional dimensions, the relation function between quality loss and process dimension tolerance has been provided, the concurrent tolerance design mathematical model based on lowest-cost and quality loss has been established. The applied case shows that this method has important guiding significance for engineering application.

scholarly journals СОВЕРШЕНСТВОВАНИЕ ГИДРОМЕЛИОРАТИВНЫХ МАШИНС  АВТОМАТИЗАЦИЕЙ ПРОЦЕССА ПОЛИВА

2019 ◽  
Author(s):  
A. Akhtyamov ◽  
A. Ryazantsev ◽  
O. Gavrilina ◽  
A. Boyko ◽  
S. Borychev ◽  
...  
Keyword(s):  
Low Cost ◽  
Economic Effect ◽  
Hydraulic Drive ◽  
Cost Savings ◽  
Practical Implementation ◽  
High Productivity ◽  
Low Degree ◽  
The Cost ◽  
Positive Results ◽  
Horizontal Arrangement

Целью исследования являлось теоретическое обоснование и практическая реализация нового способа полива гидромелиоративной машиной Фрегат с гидроприводом на сложном рельефе с минимальными затратами на модернизацию и энергозатратами. Объектом исследования является экспериментальный кранзадатчик скорости, устанавливаемый на гидромелиоративную машину. Исследования проводились в сравнении с показателями машин серийного производства. В ходе исследования было установлено, что существующая технология полива не отвечает необходимым требованиям гидромелиорации и имеет низкую степень экономической эффективности. Предлагаемая технология полива решает вопрос неравномерного распределения влаги по площади, повышает урожайность и снижает стоимость обслуживания машины вследствие уменьшения числа поломок. Имеющиеся модернизации дождевальной машины (ДМ) Фрегат , позволяющие работать по предлагаемой технологии, сложны по конструкции, ненадежны и имеют относительно высокую стоимость модернизации и сезонного обслуживания. С целью увеличения экономии средств и упрощения процесса модернизации серийных машин был разработан и протестирован кранзадатчик скорости, позволяющий снизить риск эрозии почв, застревания колес тележек и, тем самым, простой машины с необходимостью ее ремонта. Главной особенностью экспериментального краназадатчика скорости является его горизонтальное расположение относительно тележки. Два плеча с увеличенной длиной позволяют задавать поливную норму путем касания вех в начале каждого сектора, где необходимо сменить скорость движения машины. Таким образом, происходит регулирование поливной нормы, выдаваемой машиной при ее движении по орошаемой площади. Получившийся экономический эффект позволяет утверждать о положительных результатах в проведенных исследованияхThe aim of the research is the theoretical justification and practical implementation of the new method of irrigation irrigation and drainage machines Frigat with hydraulic drive for complex tasks of modernization and energy consumption. The object of the study is an experimental speedadjusting crane installed on a water reclamation machine. The studies were conducted in comparison with indicators of machine production. In the course of research it was found that the existing technology does not meet the requirements of irrigation and drainage and has a low degree of economic efficiency. The issue of uneven distribution of the owner by area, high productivity and low cost of maintenance is being addressed. DM Frigat, which allows you to work on the proposed technologies, does not require the cost of modernization and seasonal maintenance. In order to increase cost savings and develop new models of machines, a speed control crane has been developed and tested to reduce the risk of machine destruction. The operation of the trolley is the horizontal arrangement of the trolley. The speed of the machine can be increased. Thus, regulation of the irrigation rate occurs. The resulting economic effect allows us to argue about the positive results in the studies

scholarly journals Efficiency of using flour from hydrobionts of different cooking technologies in the diet of rain-bow trout

2021 ◽  
pp. 50-53
Author(s):  
Dmitriy Sergeevich Vasiliev ◽  
Sergey Petrovich Moskalenko ◽  
Irina Vasilievna Poddubnaya ◽  
Olga Evgenievna Vilutis
Keyword(s):  
Rainbow Trout ◽  
Fish Meal ◽  
Low Cost ◽  
Economic Effect ◽  
Live Weight ◽  
Feed Costs ◽  
The Cost ◽  
Protein Feed ◽  
Positive Effect ◽  
Experimental Group

The introduction of high-protein feed from crustacean processing products in the form of flour into the composition of the rainbow trout compound feed has a positive effect on the growth of fish live weight, reduces feed costs, does not change the biochemical composition of the blood, changes the chemical composition of muscle tissue, improves the amino acid rate in the 1st experimental group. Due to the relatively low cost in comparison with fish meal, the use of crayfish meal makes the cost of compound feed cheaper and increases the economic effect of growing rainbow trout.

Performance Analysis of GFRP/Steel Composite Box Beams

2012 ◽  
Vol 166-169 ◽  
pp. 716-719
Author(s):  
Yun Yu Li ◽  
Yan Lei Wang ◽  
Jin Ping Ou
Keyword(s):  
Cross Section ◽  
Low Cost ◽  
Volume Ratio ◽  
Shear Capacity ◽  
Steel Plates ◽  
Box Beam ◽  
Box Beams ◽  
New Type ◽  
Steel Composite ◽  
The Cost

To overcome the inadequacy such as the low stiffness, the weak shear capacity, brittle failure and the big initial cost in all FRP box beam, and to make use of the benefits of steel such as the high stiffness, the strong shear capacity, good ductility and the low cost, a new type of GFRP/steel composite box beam was proposed. A given GFRP box beam was used to investigate the effects of adding steel volume ratio (the ratio of steel volume to the total volume in the adding section) on the performance of the GFRP box beam by theoretical calculation, and the adding sections of steel plates for GFRP box beam included top and bottom flanges, and all cross-section, respectively. The analytical results indicate that the performance of GFRP box beam increases dramatically and the cost of beam remains almost unchanged after adding steel plates. At the same time, the performance of GFRP box beam is obviously more excellent by adding steel plates into the all cross-section compared with top and bottom flanges.

scholarly journals Cost/Performance Tradeoffs for Reflectors Used in Solar Concentrating Dish Systems

2008 ◽  
Author(s):  
Charles E. Andraka
Keyword(s):  
Low Cost ◽  
Economic Value ◽  
Thermodynamic Cycle ◽  
Heat Absorber ◽  
Receiver System ◽  
Parabolic Dish ◽  
Slope Error ◽  
The Cost ◽  
The Impact ◽  
Normally Distributed

Concentrating Solar Power (CSP) dish systems use a parabolic dish to concentrate sunlight, providing heat for a thermodynamic cycle to generate shaft power and ultimately, electricity. Currently, leading contenders use a Stirling cycle engine with a heat absorber surface at about 800°C. The concentrated light passes through an aperture, which controls the thermal losses of the receiver system. Similar systems may use the concentrated light to heat a thermochemical process. The concentrator system, typically steel and glass, provides a source of fuel over the service life of the system, but this source of fuel manifests as a capital cost up front. Therefore, it is imperative that the cost of the reflector assembly is minimized. However, dish systems typically concentrate light to a peak of as much as 13,000 suns, with an average geometric concentration ratio of over 3000 suns. Several recent dish-Stirling systems have incorporated reflector facets with a normally-distributed surface slope error (local distributed waviness) of 0.8 mrad RMS (1-sigma error). As systems move toward commercialization, the cost of these highly accurate facets must be assessed. However, when considering lower-cost options, any decrease in the performance of the facets must be considered in the evaluation of such facets. In this paper, I investigate the impact of randomly-distributed slope errors on the performance, and therefore the value, of a typical dish-Stirling system. There are many potential sources of error in a concentrating system. When considering facet options, the surface waviness, characterized as a normally-distributed slope error, has the greatest impact on the aperture size and therefore the thermal losses. I develop an optical model and a thermal model for the performance of a baseline system. I then analyze the impact on system performance for a range of mirror quality, and evaluate the impact of such performance changes on the economic value of the system. This approach can be used to guide the evaluation of low-cost facets that differ in performance and cost. The methodology and results are applicable to other point- and line-focus thermal systems including dish-Brayton, dish-Thermochemical, tower systems, and troughs.

Model of Deep Foundation Pit Supporting Technology - Hanging Pit

2013 ◽  
Vol 353-356 ◽  
pp. 2827-2830
Author(s):  
Qing Min Gao ◽  
Kai Chao Jin
Keyword(s):  
Low Cost ◽  
Retaining Wall ◽  
Engineering Application ◽  
Point Of View ◽  
Construction Technology ◽  
Deep Foundation ◽  
Foundation Pit ◽  
Deep Foundation Pit ◽  
Concrete Pile ◽  
New Construction

From the point of view of engineering application, this paper systematically discusses the characteristics of soil retaining, watertight aspects of retaining wall which combined mixing piles of waterproof curtain and bored concrete pile . Aiming at the shortcomings of construction process of the open caisson , this paper puts forward a new type of supporting technology of deep foundation pit - hanging construction technology for foundation pit supporting.It is security construction ,no effect on environment, low cost, and so on. The thesis introduces the technology principal, construction procedures and related points of the new construction technology.

PROSPECTS OF STRENGTHENING OF SHREDDERS KNIVES OF INDUSTRIAL INSTALLATIONS

2021 ◽  
Vol 3 (144) ◽  
pp. 94-99
Author(s):  
Vyacheslav F. Aulov ◽  
◽  
Yuriy N. Rozhkov ◽  
Valentin P. Lyalyakin
Keyword(s):  
High Frequency ◽  
Lower Cost ◽  
Low Cost ◽  
Economic Effect ◽  
Labor Cost ◽  
Research Purpose ◽  
Labor Costs ◽  
Industrial Plants ◽  
The Cost ◽  
Frequency Heating

The main goal of agriculture is to obtain products, but its processing is no less important. At processing enterprises, grinding and cutting are the most important technological process. (Research purpose) The research purpose is in analyzing the market of knives of processing machines, their pricing, resource and describing the economic efficiency of applying strengthening coatings. (Materials and methods) Authors used a digital method of searching through the Internet for enterprises that produce knives for processing machines, types of knives and their characteristics. (Results and discussion) Specialized knives are used for grinding products in the industrial plants. Since knives are a consumable item, the technology of their replacement is subject to requirements for the simplicity of the process, low cost and low labor cost. These requirements, together with the specific ones determined by the technology, form the design of the knives. The efficiency of the processing machine directly depends on the state of its working organs. Replacement of worn-out elements is accompanied by large labor costs, which leads to a decrease in labor productivity and to downtime of equipment in repair, and ultimately − to a decrease in the profit of the enterprise. (Conclusions) The hardening of knives by the borating method using high-frequency heating will increase the productivity of agricultural machinery and will give an economic effect up to 0.32 billion rubles due to an increase in the resource and a lower cost of manufacturing hardened knives compared to imported ones. By reducing the cost of domestic knives, you can get savings on one knife of 1960 rubles, provided that you refuse to purchase imported knives.

scholarly journals ECONOMIC ASPECTS OF THE ORGANIZATION OF CARBON FARMS ON FOREST SITE

2021 ◽  
Vol 9 (1) ◽  
pp. 17-25
Author(s):  
Svetlana Morkovina ◽  
Ekaterina Panyavina ◽  
I. Shanin ◽  
Irina Avdeeva
Keyword(s):  
Carbon Dioxide Emissions ◽  
Carbon Balance ◽  
Economic Effect ◽  
Forest Carbon ◽  
Forest Site ◽  
Economic Aspects ◽  
Voronezh Region ◽  
New Type ◽  
Forest Lands ◽  
The Cost

The article considers the possibilities of developing forest entrepreneurship through expanding the range of ecosystem services and organizing sequestration Inustry on forest lands. The new type of forest management is based on the ability to balance carbon dioxide emissions into the atmosphere. The economic aspects of creating and using forest carbon farms are considered. To determine the standard costs for creating poplar and pine carbon plantations, the standard method was used. Creating carbon farms on forest land is a costly process, but carbon storage activities can bring numerous economic and environmental effects in addition to maintaining the carbon balance. The cost of creating one hectare of forest carbon farm is from 262 to 304 thousand rubles, while the economic effect of their use can significantly exceed the investment. The first stage in the organization of carbon farms should be the creation of test plantations-carbon polygons. It is proved that the necessary resources and prerequisites are available for the implementation of the actual practice-oriented task of creating carbon polygons in the Voronezh region.

LIFE SKILLS EDUCATION FOR SCHOOL DROP OUTS IN TAMAN SARI, DISTRICT BOGOR REGENCY

2019 ◽  
Vol 1 (2) ◽  
pp. 46
Author(s):  
Stefani Nawati EKORESTI
Keyword(s):  
Life Skills ◽  
Economic Value ◽  
Skills Training ◽  
Poor People ◽  
Housing Conditions ◽  
The Cost ◽  
Skills Education ◽  
Work Done ◽  
Drop Outs ◽  
Life Skills Education

Taman Sari Sub-District, Bogor Regency has the potential for fertile soil. But these lands have not been tilled properly. Narrow housing conditions, especially for poor people, do not allow residents to plant crops. Causing the lack of consumption of vegetables; which causes residents become easily sick. In addition, there is also a lot of plastic waste, especially bottled drinking water and other things that come from tourists and fishermen who have not been processed. This condition gave rise to the idea to provide life skills training in making vertical gardens, hydroponic plants and waste management. Besides the need for makeup and haircutting skills also needed especially for orphans fostered by Yasayan Usawatun Hasanah. Community Service Activities (PkM) aims to foster community awareness of the cleanliness of the environment and empower citizens to be more creative and entrepreneurial. Therefore, in addition to the types of activities requested by the residents, UPBJJ-UT Bogor will also teach about identifying the economic value of the work done in the form of determining the cost of goods sold / production. This activity was attended by 50 orphans and it ran smoothly and successfully. Now orphans already have life skills that hope can lift their economy.

Advance Protection for Three Phase Induction Motor using Microcontroller Atmega32

2018 ◽  
Vol 8 (1) ◽  
pp. 172
Author(s):  
Karan S Belsare ◽  
Gajanan D Patil
Keyword(s):  
Induction Motor ◽  
Low Cost ◽  
Short Circuit ◽  
Cost Factor ◽  
Protection Scheme ◽  
Three Phase ◽  
The Cost

A low cost and reliable protection scheme has been designed for a three phase induction motor against unbalance voltages, under voltage, over voltage, short circuit and overheating protection. Taking the cost factor into consideration the design has been proposed using microcontroller Atmega32, MOSFETs, relays, small CTs and PTs. However the sensitivity of the protection scheme has been not compromised. The design has been tested online in the laboratory for small motors and the same can be implemented for larger motors by replacing the i-v converters and relays of suitable ratings.

Sign in / Sign up

Export Citation Format

Share Document