scholarly journals Effect of Landslide Surge on Pile Foundation of Overhead Vertical Wharf

2020 ◽  
Vol 2020 ◽  
pp. 1-8
Author(s):  
Xiaolong Zhang ◽  
Junshuai Mu ◽  
Chengzhi Wang ◽  
Duoyin Wang
Keyword(s):  
Experimental Data ◽  
Influencing Factors ◽  
Structural Design ◽  
Empirical Formula ◽  
Pile Foundation ◽  
Extreme Values ◽  
Wave Pressure ◽  
Pressure Time ◽  
Great Harm ◽  
Good Agreement

Waves generated by landslides into water cause great harm to wharfs. Hence, the surge wave pressure generated by the landslide serves as an important reference for the structural design of wharfs in reservoir areas. In this study, a series of hydraulic model tests were performed to study the energy and wave pressure produced by the surge. According to wave pressure-time curves, the extreme values of sudden transient changes in wave pressure are obtained. The mechanism and influencing factors of surge wave pressure on vertical wharf buildings are expounded. On this basis, a formula to calculate the wave pressure exerted by landslide surge on the pile foundation of an overhead vertical wharf is developed. A large number of experiments show that the empirical formula is in good agreement with the experimental data.

Model Test Research on Soil-Landslide Surge by River Channel Reservoir

2013 ◽  
Vol 353-356 ◽  
pp. 2610-2613
Author(s):  
Li Chen ◽  
Ping Yi Wang ◽  
Tao Yu ◽  
Fan Zhang ◽  
Yong Qiang Men
Keyword(s):  
Experimental Data ◽  
Influencing Factors ◽  
Model Test ◽  
Empirical Formula ◽  
Exchange Process ◽  
River Channel ◽  
Test Results ◽  
Generalized Model ◽  
Landslide Occurrence

By fully collected and surveyed on the soil landslide, with the help of generalized model, the experiment simulated the landslide occurrence and exchange process of soil landslide entered the water. Through the calculation and analysis of test results and influencing factors, it is given out the height of the initial surge, variation of the progressive surge and empirical formula of soil-landslide surge. Compared with experimental data, it is found that empirical formula has certain accuracy and it can provide a certain reference on surge disaster forecast.

CFD Analysis of Gas-Insulated Transformers

2004 ◽  
Author(s):  
D. J. Lee ◽  
S. S. Seol ◽  
I. S. Park ◽  
J. H. Kim ◽  
S. B. Shin ◽  
...  
Keyword(s):  
Experimental Data ◽  
Design Process ◽  
Temperature Rise ◽  
Empirical Formula ◽  
Pressure Loss ◽  
Thermal Design ◽  
Cfd Analysis ◽  
Empirical Formulas ◽  
Loss Of Coolant ◽  
Good Agreement

A thermal design of transformers has been performed using an empirical formula. In order to reduce the developing cost and time, CFD analysis is used in thermal design process for gas-insulated transformers. We calculated the pressure loss of coolant and the temperature rise of winding with empirical formulas and CFD analysis. Also, we constructed some real machines and compared the analytic results with the experimental data. The comparison shows a good agreement between the CFD calculations and experimental results.

Calculation and Analysis of Submersible Well Pump Clearance Leakage Loss

2013 ◽  
Vol 456 ◽  
pp. 225-229
Author(s):  
Xiong Fa Gao ◽  
Wei Dong Shi ◽  
Qi Hua Zhang ◽  
De Sheng Zhang
Keyword(s):  
Experimental Data ◽  
Numerical Simulation ◽  
Empirical Formula ◽  
Guide Vane ◽  
Three Dimensional ◽  
Integral Model ◽  
Leakage Loss ◽  
Second Stage ◽  
External Characteristics ◽  
Good Agreement

The 200QJ80-22 submersible well pump was investigated to predict the effects of leakage change of the submersible well pump on external characteristics. The integral model of impeller, guide vane and wear-ring was established and the numerical simulation for three-dimensional whole flow field was carried out. The results show that the predicted results have a good agreement with the experimental data. The result of the numerical simulation shows that the head and efficiency of pump decrease with the size of clearance increasing. Especially when the size of clearance is larger than 0.7 mm, the decreasing becomes more obvious. The leakage calculated through numerical simulation were compared with the values obtained according to empirical formula and the results indicates internal clearance leakage at design point is close to the value calculated through empirical formula in smaller wear-ring clearance, but the simulated values of leakage have a small gap with calculated value obtained from empirical formula. Simultaneously, the Second stage leakage decrease significantly compared to the first stage leakage with the flow rate increasing, while the values got by the empirical formula have a small gap with simulated values obtained.

Energy Levels and Electromagnetic Transition of 90-94mo Nuclei Using Ibm-1

2020 ◽  
pp. 149-152
Keyword(s):  
Experimental Data ◽  
Transition Probability ◽  
Energy Levels ◽  
Dynamical Symmetry ◽  
Interacting Boson Model ◽  
Excitation Energies ◽  
Electromagnetic Transition ◽  
Boson Model ◽  
Energy States ◽  
Good Agreement

The energy states for the J , b , ɤ bands and electromagnetic transitions B (E2) values for even – even molybdenum 90 – 94 Mo nuclei are calculated in the present work of "the interacting boson model (IBM-1)" . The parameters of the equation of IBM-1 Hamiltonian are determined which yield the best excellent suit the experimental energy states . The positive parity of energy states are obtained by using IBS1. for program for even 90 – 94 Mo isotopes with bosons number 5 , 4 and 5 respectively. The" reduced transition probability B(E2)" of these neuclei are calculated and compared with the experimental data . The ratio of the excitation energies of the 41+ to 21+ states ( R4/2) are also calculated . The calculated and experimental (R4/2) values showed that the 90 – 94 Mo nuclei have the vibrational dynamical symmetry U(5). Good agreement was found from comparison between the calculated energy states and electric quadruple probabilities B(E2) transition of the 90–94Mo isotopes with the experimental data .

Predicting the Effect of Tire Tread Pattern Design on Thick Film Wet Traction

1977 ◽  
Vol 5 (1) ◽  
pp. 6-28 ◽  
Author(s):  
A. L. Browne
Keyword(s):  
Experimental Data ◽  
Network Design ◽  
Thick Film ◽  
Digital Computer ◽  
Analytical Tool ◽  
Design Practice ◽  
Pattern Design ◽  
Performance Results ◽  
Good Agreement

Abstract An analytical tool is presented for the prediction of the effects of changes in tread pattern design on thick film wet traction performance. Results are reported for studies in which the analysis, implemented on a digital computer, was used to determine the effect of different tread geometry features, among these being the number, width, and lateral spacing of longitudinal grooves and the angle of zigzags in longitudinal grooves, on thick film wet traction. These results are shown to be in good agreement with experimental data appearing in the literature and are used to formulate guidelines for tread groove network design practice.

A New Condition of Formation and Stablity of All Crystalline Systems in a Good Agreement with Experimental Data

2015 ◽  
Vol 11 (3) ◽  
pp. 3224-3228
Author(s):  
Tarek El-Ashram
Keyword(s):  
Experimental Data ◽  
Brillouin Zone ◽  
Electron Concentration ◽  
Free Electron ◽  
Lattice Point ◽  
Valence Electron ◽  
Fermi Gas ◽  
Valence Electron Concentration ◽  
Fermi Sphere ◽  
Good Agreement

In this paper we derived a new condition of formation and stability of all crystalline systems and we checked its validity andit is found to be in a good agreement with experimental data. This condition is derived directly from the quantum conditionson the free electron Fermi gas inside the crystal. The new condition relates both the volume of Fermi sphere VF andvolume of Brillouin zone VB by the valence electron concentration VEC as ;𝑽𝑭𝑽𝑩= 𝒏𝑽𝑬𝑪𝟐for all crystalline systems (wheren is the number of atoms per lattice point).

Virus Removal by Filtration

1982 ◽  
Vol 14 (4-5) ◽  
pp. 253-256
Author(s):  
N Sriramula ◽  
M Chaudhuri
Keyword(s):  
Experimental Data ◽  
Escherichia Coli ◽  
Cationic Polyelectrolyte ◽  
Electrokinetic Phenomena ◽  
Virus Removal ◽  
Bacterial Virus ◽  
Gravity Settling ◽  
And Diffusion ◽  
Model Virus ◽  
Good Agreement

An investigation was undertaken on the removal of a model virus, bacterial virus MS2 against Escherichia coli, by sand filtration using untreated, and alum or cationic polyelectrolyte treated media, and uncoagulated as well as alum coagulated influent. Data on discrete virus removal were satisfactorily accounted for by electrokinetic phenomena and diffusion. For virus in association with turbidity, filter coefficients computed from experimental data were in good agreement with those predicted by mechanical straining and gravity settling which were the dominant mechanisms for removal of the turbidity particles to which the viruses attached.

Diffusion model for deposition of epitaxial GaAs layers prepared by the MOCVD method

1991 ◽  
Vol 56 (10) ◽  
pp. 2020-2029
Author(s):  
Jindřich Leitner ◽  
Petr Voňka ◽  
Josef Stejskal ◽  
Přemysl Klíma ◽  
Rudolf Hladina
Keyword(s):  
Experimental Data ◽  
Growth Rate ◽  
Kinetic Model ◽  
Gas Phase ◽  
Substrate Surface ◽  
Deposition Process ◽  
Hydrogen Atmosphere ◽  
Epitaxial Gaas ◽  
Kinetics Of ◽  
Good Agreement

The authors proposed and treated quantitatively a kinetic model for deposition of epitaxial GaAs layers prepared by reaction of trimethylgallium with arsine in hydrogen atmosphere. The transport of gallium to the surface of the substrate is considered as the controlling process. The influence of the rate of chemical reactions in the gas phase and on the substrate surface on the kinetics of the deposition process is neglected. The calculated dependence of the growth rate of the layers on the conditions of the deposition is in a good agreement with experimental data in the temperature range from 600 to 800°C.

Numerical evaluation of hydrodynamic characteristics of planing hulls by using a hybrid method

2021 ◽  
pp. 147509022199024
Author(s):  
Emre Kahramanoglu ◽  
Silvia Pennino ◽  
Huseyin Yilmaz
Keyword(s):  
Experimental Data ◽  
Hybrid Method ◽  
Design Stage ◽  
Hydrodynamic Characteristics ◽  
Calm Water ◽  
Preliminary Design Stage ◽  
Reduction Function ◽  
Hull Forms ◽  
Good Agreement

The hydrodynamic characteristics of the planing hulls in particular at the planing regime are completely different from the conventional hull forms and the determination of these characteristics is more complicated. In the present study, calm water hydrodynamic characteristics of planing hulls are investigated using a hybrid method. The hybrid method combines the dynamic trim and sinkage from the Zarnick approach with the Savitsky method in order to calculate the total resistance of the planing hull. Since the obtained dynamic trim and sinkage values by using the original Zarnick approach are not in good agreement with experimental data, an improvement is applied to the hybrid method using a reduction function proposed by Garme. The numerical results obtained by the hybrid and improved hybrid method are compared with each other and available experimental data. The results indicate that the improved hybrid method gives better results compared to the hybrid method, especially for the dynamic trim and resistance. Although the results have some discrepancies with experimental data in terms of resistance, trim and sinkage, the improved hybrid method becomes appealing particularly for the preliminary design stage of the planing hulls.

scholarly journals Fatigue Modeling and Numerical Analysis of Re-Filling Probe Hole of Friction Stir Spot Welded Joints in Aluminum Alloys

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2171
Author(s):  
Armin Yousefi ◽  
Ahmad Serjouei ◽  
Reza Hedayati ◽  
Mahdi Bodaghi
Keyword(s):  
Experimental Data ◽  
Tensile Strength ◽  
Fatigue Life ◽  
Fatigue Strength ◽  
Fatigue Behavior ◽  
Element Model ◽  
Plastic Strain Amplitude ◽  
Friction Stir ◽  
Probe Hole ◽  
Good Agreement

In the present study, the fatigue behavior and tensile strength of A6061-T4 aluminum alloy, joined by friction stir spot welding (FSSW), are numerically investigated. The 3D finite element model (FEM) is used to analyze the FSSW joint by means of Abaqus software. The tensile strength is determined for FSSW joints with both a probe hole and a refilled probe hole. In order to calculate the fatigue life of FSSW joints, the hysteresis loop is first determined, and then the plastic strain amplitude is calculated. Finally, by using the Coffin-Manson equation, fatigue life is predicted. The results were verified against available experimental data from other literature, and a good agreement was observed between the FEM results and experimental data. The results showed that the joint’s tensile strength without a probe hole (refilled hole) is higher than the joint with a probe hole. Therefore, re-filling the probe hole is an effective method for structures jointed by FSSW subjected to a static load. The fatigue strength of the joint with a re-filled probe hole was nearly the same as the structure with a probe hole at low applied loads. Additionally, at a high applied load, the fatigue strength of joints with a refilled probe hole was slightly lower than the joint with a probe hole.

Sign in / Sign up

Export Citation Format

Share Document