scholarly journals Porous Silk Scaffold Derived from Formic Acid: Characterization and Biocompatibility

2021 ◽  
Vol 2021 ◽  
pp. 1-6
Author(s):  
Ting Zhang ◽  
Qianwei Xiong ◽  
Yuxi Shan ◽  
Feng Zhang ◽  
Shijun Lu
Keyword(s):  
Mechanical Properties ◽  
Formic Acid ◽  
Porous Scaffold ◽  
Space Structure ◽  
Tissue Growth ◽  
3D Scaffold ◽  
Salt Leaching ◽  
3D Space ◽  
Potential Applications ◽  
Silk Scaffold

Silk porous scaffold possesses 3D space structure for cell adhesion and tissue growth and demonstrates promising applications in biomedical engineering. In this study, a porous silk scaffold was prepared from formic acid, and its morphology, structure, mechanical properties, and biocompatibility were characterized. The preparation process involved silk dissolution in formic acid and salt leaching in water, avoiding widely used organic solvent-induced crystallization including methanol or ethanol. The resulting porous silk scaffolds showed good pore structure, stable silk II crystalline structure, good mechanical properties, and enhanced cell biocompatibility. Therefore, these findings demonstrate that porous silk scaffold derived from formic acid has great potential applications as 3D scaffold for cell culture and tissue repair.

scholarly journals A Slot-Die Technique for the Preparation of Continuous, High-Area, Chitosan-Based Thin Films

Polymers ◽  
2021 ◽  
Vol 13 (10) ◽  
pp. 1566
Author(s):  
Oliver J. Pemble ◽  
Maria Bardosova ◽  
Ian M. Povey ◽  
Martyn E. Pemble
Keyword(s):  
Thin Films ◽  
Mechanical Properties ◽  
High Volume ◽  
Mechanical Anisotropy ◽  
Diverse Range ◽  
Direction Parallel ◽  
High Area ◽  
Wide Range ◽  
Slot Die ◽  
Potential Applications

Chitosan-based films have a diverse range of potential applications but are currently limited in terms of commercial use due to a lack of methods specifically designed to produce thin films in high volumes. To address this limitation directly, hydrogels prepared from chitosan, chitosan-tetraethoxy silane, also known as tetraethyl orthosilicate (TEOS) and chitosan-glutaraldehyde have been used to prepare continuous thin films using a slot-die technique which is described in detail. By way of preliminary analysis of the resulting films for comparison purposes with films made by other methods, the mechanical strength of the films produced was assessed. It was found that as expected, the hybrid films made with TEOS and glutaraldehyde both show a higher yield strength than the films made with chitosan alone. In all cases, the mechanical properties of the films were found to compare very favorably with similar measurements reported in the literature. In order to assess the possible influence of the direction in which the hydrogel passes through the slot-die on the mechanical properties of the films, testing was performed on plain chitosan samples cut in a direction parallel to the direction of travel and perpendicular to this direction. It was found that there was no evidence of any mechanical anisotropy induced by the slot die process. The examples presented here serve to illustrate how the slot-die approach may be used to create high-volume, high-area chitosan-based films cheaply and rapidly. It is suggested that an approach of the type described here may facilitate the use of chitosan-based films for a wide range of important applications.

scholarly journals The Infuence of Salicin on Rheological and Film-Forming Properties of Collagen

Molecules ◽  
2021 ◽  
Vol 26 (6) ◽  
pp. 1661
Author(s):  
Katarzyna Adamiak ◽  
Katarzyna Lewandowska ◽  
Alina Sionkowska
Keyword(s):  
Mechanical Properties ◽  
Atomic Force Microscopy ◽  
Infrared Spectroscopy ◽  
Rheological Properties ◽  
Silver Carp ◽  
Shear Tests ◽  
Force Microscopy ◽  
Atomic Force ◽  
Film Forming ◽  
Potential Applications

Collagen films are widely used as adhesives in medicine and cosmetology. However, its properties require modification. In this work, the influence of salicin on the properties of collagen solution and films was studied. Collagen was extracted from silver carp skin. The rheological properties of collagen solutions with and without salicin were characterized by steady shear tests. Thin collagen films were prepared by solvent evaporation. The structure of films was researched using infrared spectroscopy. The surface properties of films were investigated using Atomic Force Microscopy (AFM). Mechanical properties were measured as well. It was found that the addition of salicin modified the roughness of collagen films and their mechanical and rheological properties. The above-mentioned parameters are very important in potential applications of collagen films containing salicin.

scholarly journals Fabrication of Polycaprolactone/Nano Hydroxyapatite (PCL/nHA) 3D Scaffold with Enhanced In Vitro Cell Response via Design for Additive Manufacturing (DfAM)

Polymers ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1394
Author(s):  
Yong Sang Cho ◽  
So-Jung Gwak ◽  
Young-Sam Cho
Keyword(s):  
Mechanical Properties ◽  
Cell Response ◽  
Structural Characteristics ◽  
Structure Design ◽  
Compressive Modulus ◽  
Control Group ◽  
Design For Additive Manufacturing ◽  
3D Scaffold ◽  
3D Printed

In this study, we investigated the dual-pore kagome-structure design of a 3D-printed scaffold with enhanced in vitro cell response and compared the mechanical properties with 3D-printed scaffolds with conventional or offset patterns. The compressive modulus of the 3D-printed scaffold with the proposed design was found to resemble that of the 3D-printed scaffold with a conventional pattern at similar pore sizes despite higher porosity. Furthermore, the compressive modulus of the proposed scaffold surpassed that of the 3D-printed scaffold with conventional and offset patterns at similar porosities owing to the structural characteristics of the kagome structure. Regarding the in vitro cell response, cell adhesion, cell growth, and ALP concentration of the proposed scaffold for 14 days was superior to those of the control group scaffolds. Consequently, we found that the mechanical properties and in vitro cell response of the 3D-printed scaffold could be improved by kagome and dual-pore structures through DfAM. Moreover, we revealed that the dual-pore structure is effective for the in vitro cell response compared to the structures possessing conventional and offset patterns.

scholarly journals Smart Hydrogel Bilayers Prepared by Irradiation

Polymers ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1753
Author(s):  
Weixian Huo ◽  
Heng An ◽  
Shuquan Chang ◽  
Shengsheng Yang ◽  
Yin Huang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Gamma Radiation ◽  
Antibacterial Properties ◽  
Cross Linking ◽  
Temperature Sensitive ◽  
Temperature Changes ◽  
Smart Hydrogel ◽  
Isopropyl Acrylamide ◽  
Hydrogel Synthesis ◽  
Potential Applications

Environment-responsive hydrogel actuators have attracted tremendous attention due to their intriguing properties. Gamma radiation has been considered as a green cross-linking process for hydrogel synthesis, as toxic cross-linking agents and initiators were not required. In this work, chitosan/agar/P(N-isopropyl acrylamide-co-acrylamide) (CS/agar/P(NIPAM-co-AM)) and CS/agar/Montmorillonite (MMT)/PNIPAM temperature-sensitive hydrogel bilayers were synthesized via gamma radiation at room temperature. The mechanical properties and temperature sensitivity of hydrogels under different agar content and irradiation doses were explored. The enhancement of the mechanical properties of the composite hydrogel can be attributed to the presence of agar and MMT. Due to the different temperature sensitivities provided by the two layers of hydrogel, they can move autonomously and act as a flexible gripper as the temperature changes. Thanks to the antibacterial properties of the hydrogel, their storage time and service life may be improved. The as prepared hydrogel bilayers have potential applications in control devices, soft robots, artificial muscles and other fields.

Structural-Mechanical Properties of Polyurethane Surface after Carbon Ion Subplantation

2021 ◽  
Vol 887 ◽  
pp. 370-375
Author(s):  
I.A. Morozov ◽  
A.S. Kamenetskikh
Keyword(s):  
Mechanical Properties ◽  
Surface Relief ◽  
Low Energy ◽  
Plasma Modification ◽  
Carbon Ions ◽  
Uniaxial Deformation ◽  
Treatment Regimes ◽  
Subsequent Investigation ◽  
Ion Plasma ◽  
Potential Applications

Ion-plasma modification of polymers has many potential applications, in particular, in the development of biomedical products. Treatment of soft polymers can easily damage the surface; low-energy plasma and subsequent investigation of the structural and mechanical properties of the surface are required. Polyurethane is a widely used block copolymer. Subplantation of carbon ions heterogeneously changes the structural and mechanical properties of the surface (relief, stiffness, thickness of the modified coating), forming a graphene-like nanolayer. Uniaxial deformation of the treated materials in some cases leads to the damage of the surface (local nanocracks, folds). Materials have increased hydrophobicity, good deformability (valid for certain treatment regimes) and can find application in design of products with improved biomedical properties.

scholarly journals Biological Effect of Gas Plasma Treatment on CO2Gas Foaming/Salt Leaching Fabricated Porous Polycaprolactone Scaffolds in Bone Tissue Engineering

2014 ◽  
Vol 2014 ◽  
pp. 1-6 ◽  
Author(s):  
Tae-Yeong Bak ◽  
Min-Suk Kook ◽  
Sang-Chul Jung ◽  
Byung-Hoon Kim
Keyword(s):  
Tissue Engineering ◽  
Bone Tissue Engineering ◽  
Bone Tissue ◽  
Nitrogen Plasma ◽  
Salt Leaching ◽  
Foaming Process ◽  
Gas Plasma ◽  
Plasma Surface Treatment ◽  
Potential Applications ◽  
Gas Foaming

Porous polycaprolactone (PCL) scaffolds were fabricated by using the CO2gas foaming/salt leaching process and then PCL scaffolds surface was treated by oxygen or nitrogen gas plasma in order to enhance the cell adhesion, spreading, and proliferation. The PCL and NaCl were mixed in the ratios of 3 : 1. The supercritical CO2gas foaming process was carried out by solubilizing CO2within samples at 50°C and 8 MPa for 6 hr and depressurization rate was 0.4 MPa/s. The oxygen or nitrogen plasma treated porous PCL scaffolds were prepared at discharge power 100 W and 10 mTorr for 60 s. The mean pore size of porous PCL scaffolds showed 427.89 μm. The gas plasma treated porous PCL scaffolds surface showed hydrophilic property and the enhanced adhesion and proliferation of MC3T3-E1 cells comparing to untreated porous PCL scaffolds. The PCL scaffolds produced from the gas foaming/salt leaching and plasma surface treatment are suitable for potential applications in bone tissue engineering.

Pseudoelasticity of Cu-13.8Al-Ni Alloys Containing V and Nb

2008 ◽  
Vol 59 ◽  
pp. 101-107 ◽  
Author(s):  
Rodinei Medeiros Gomes ◽  
Ana Cris R. Veloso ◽  
V.T.L. Buono ◽  
Severino Jackson Guedes de Lima ◽  
Tadeu Antonio de Azevedo Melo
Keyword(s):  
Mechanical Properties ◽  
Shape Memory ◽  
Shape Recovery ◽  
Cold Water ◽  
Low Cost ◽  
Tensile Tests ◽  
Grain Refiner ◽  
Good Shape ◽  
Potential Applications ◽  
Superelastic Behavior

Polycrystalline copper-based shape memory alloys have been of particular interest in relation to Ni-Ti because of their low cost and good shape memory effect. Nevertheless the absence of a pronounced pseudoelasticity effect restricts the number of potential applications. In this work, the influence of Nb and V on the microstructure and the mechanical properties was investigated. Samples of Cu-13.8 Al-Ni containing V and Nb alloy were prepared by induction and solution treated at 850°C and then further quenched into cold water. The addition of Nb and V promotes the formation of precipitates which act as grain refiner and subsequently improve the mechanical properties. The tensile tests were performed at temperatures slightly inferior to Mf and superior to Af, to investigate the shape recovery and pseudoelasticity, respectively. Based on the analyses of the Cu-13,8Al-2Ni-1Nb (wt%) alloy was detected rupture strains greater than 14%, besides observation of the superelasticity of these alloys and quantification of this property by means of cycling, from 0 to strains between 1 and 7%. The studies performed on alloy Cu-13.8Al- 3,5Ni-1V (wt%) made it possible to determine rupture strains in the order of 3% and its superelastic behavior through cycling for deformations between 1 and 3%.

scholarly journals The Combined Effects of Co-Culture and Substrate Mechanics on 3D Tumor Spheroid Formation within Microgels Prepared via Flow-Focusing Microfluidic Fabrication

Pharmaceutics ◽  
2018 ◽  
Vol 10 (4) ◽  
pp. 229 ◽  
Author(s):  
Dongjin Lee ◽  
Chaenyung Cha
Keyword(s):  
Mechanical Properties ◽  
Cell Culture ◽  
Microfluidic Device ◽  
3D Cell Culture ◽  
Breast Adenocarcinoma ◽  
Adherent Cell ◽  
Flow Focusing ◽  
Spheroid Formation ◽  
3D Scaffold ◽  
Tumor Spheroids

Tumor spheroids are considered a valuable three dimensional (3D) tissue model to study various aspects of tumor physiology for biomedical applications such as tissue engineering and drug screening as well as basic scientific endeavors, as several cell types can efficiently form spheroids by themselves in both suspension and adherent cell cultures. However, it is more desirable to utilize a 3D scaffold with tunable properties to create more physiologically relevant tumor spheroids as well as optimize their formation. In this study, bioactive spherical microgels supporting 3D cell culture are fabricated by a flow-focusing microfluidic device. Uniform-sized aqueous droplets of gel precursor solution dispersed with cells generated by the microfluidic device are photocrosslinked to fabricate cell-laden microgels. Their mechanical properties are controlled by the concentration of gel-forming polymer. Using breast adenocarcinoma cells, MCF-7, the effect of mechanical properties of microgels on their proliferation and the eventual spheroid formation was explored. Furthermore, the tumor cells are co-cultured with macrophages of fibroblasts, which are known to play a prominent role in tumor physiology, within the microgels to explore their role in spheroid formation. Taken together, the results from this study provide the design strategy for creating tumor spheroids utilizing mechanically-tunable microgels as 3D cell culture platform.

scholarly journals Preparation of alginate hydrogel microparticles by gelation introducing cross-linkers using droplet-based microfluidics: a review of methods

2021 ◽  
Vol 25 (1) ◽  
Author(s):  
Cheng Zhang ◽  
Romain Grossier ◽  
Nadine Candoni ◽  
Stéphane Veesler
Keyword(s):  
Mechanical Properties ◽  
Physicochemical Properties ◽  
Ease Of Use ◽  
Narrow Size Distribution ◽  
Future Perspectives ◽  
Alginate Hydrogel ◽  
Hydrogel Microparticles ◽  
Potential Applications ◽  
Excellent Control ◽  
On Chip

AbstractThis review examines the preparation of alginate hydrogel microparticles by using droplet-based microfluidics, a technique widely employed for its ease of use and excellent control of physicochemical properties, with narrow size distribution. The gelation of alginate is realized “on-chip” and/or “off-chip”, depending on where cross-linkers are introduced. Various strategies are described and compared. Microparticle properties such as size, shape, concentration, stability and mechanical properties are discussed. Finally, we consider future perspectives for the preparation of hydrogel microparticles and their potential applications.

Sign in / Sign up

Export Citation Format

Share Document