scholarly journals Study on the Mechanism of Stabilizing Loess with Lime: Analysis of Mineral and Microstructure Evolution

2021 ◽  
Vol 2021 ◽  
pp. 1-11
Author(s):  
Yawei Ma ◽  
Wenwu Chen
Keyword(s):  
Mineral Composition ◽  
Nitrogen Adsorption ◽  
Strength Increase ◽  
X Ray Diffraction ◽  
Compact Structure ◽  
Acicular Crystal ◽  
Mesh Structure ◽  
X Ray ◽  
Curing Period ◽  
Soil Fabric

X-ray diffraction (XRD) technique was adopted to test the mineral composition of quicklime-solidified loess with different lime-adding rates at different curing periods. Scanning electron microscopy (SEM) and nitrogen adsorption were used to analyze the microporous structure of the solidified loess. The unconfined compressive strength and limit moisture content of solidified loess were combined to analyze the evolution mechanism of mineral composition and microstructure of solidified loess with the change of curing period and clarify the mechanism of quicklime-solidified loess. The results showed reduced content of clay minerals and decrease in the number of large pores due to increase of hydrates and pozzolanic products during extended curing period. The solidified soil fabric transformed from a compact structure into a mesh structure composing of acicular crystal and cementation. The main reasons for strength increase and change of liquid and plastic limits with the lime-solidified loess after extended curing are the change of the substance and the microstructure.

Effect of Fly Ash and Slag on the Resistance to H2S Attack of Oil Well Cement

2009 ◽  
Vol 79-82 ◽  
pp. 71-74
Author(s):  
Qi Wang ◽  
Lin Qiao ◽  
Peng Song
Keyword(s):  
Fly Ash ◽  
Compression Strength ◽  
Blended Cement ◽  
Oil Well ◽  
X Ray Diffraction ◽  
X Ray ◽  
Curing Period ◽  
Oil Well Cement ◽  
Xrd Patterns ◽  
Well Cement

In this paper, the resistance to H2S attack of pastes made from slag-fly ash blended cement used in oil well (SFAOW) was studied, in which fly ash (FA) was used at replacement dosages of 30% to 60% by weight of slag. Samples of SCOW and SFAOW pastes were demoulded and cured by immersion in fresh water with 2 Mp H2S insulfflation under 130oC for 15 days. After this curing period, compression strength and permeability of the samples were investigated. The reaction mechanisms of H2S with the paste were carried out through a microstructure study, which included the use of x-ray diffraction (XRD) patterns and scanning electron microscope (SEM). Based on the obtained data in this study, incorporation of FA into SCOW results in the comparable effects in the resistance to H2S attack. When the replacement dosage of slag is about 40%, the paste exhibits the best performance on resistance to H2S attack with compression strength 36.58Mp.

Application of raw and modified Uruguayan clays to phosphate adsorption for water remediation

MRS Advances ◽  
2018 ◽  
Vol 3 (61) ◽  
pp. 3543-3549
Author(s):  
Pablo González ◽  
Andrea C. De Los Santos ◽  
Jorge R. Castiglioni ◽  
María A. De León
Keyword(s):  
Nitrogen Adsorption ◽  
Pillared Clay ◽  
Water Remediation ◽  
Phosphate Adsorption ◽  
X Ray Diffraction ◽  
Order Model ◽  
Freundlich Model ◽  
X Ray ◽  
First Order ◽  
Adsorption Desorption

ABSTRACTA raw clay from Uruguay was modified with aluminium to obtain an aluminium pillared clay (Al-PILC). The solids were characterized by scanning electron microscopy, X-ray diffraction and nitrogen adsorption-desorption isotherms. The Al-PILC retained the typical laminar structure of montmorillonite. The specific surface area and the microporous volume of the Al-PILC, 235 m2 g-1 and 0.096 cm3 g-1, respectively, were much higher than those of the clay. The phosphate adsorption capacity of the Al-PILC was higher than those of the clay. The phosphate adsorption kinetic followed the pseudo-first-order model for both, the clay and the Al-PILC, and the phosphate adsorption isotherm for the Al-PILC fit the Freundlich model.

The Adsorption and Chemistry of Tripropyl phosphate (TPP) into Microporous and Mesoporous NaX Zeolites

2011 ◽  
Vol 1304 ◽  
Author(s):  
Qingguo Meng ◽  
David C. Doetschman ◽  
Apostolos K. Rizos ◽  
Min-Hong Lee ◽  
Jürgen T. Schulte ◽  
...  
Keyword(s):  
Solid State ◽  
Structural Properties ◽  
Nmr Spectra ◽  
Nitrogen Adsorption ◽  
X Ray Diffraction ◽  
X Ray ◽  
Nax Zeolite ◽  
Stoichiometric Amount ◽  
Polydiallyldimethylammonium Chloride ◽  
Adsorption Analysis

ABSTRACTAdsorption and chemistry of tripropylphosphate (TPP) in mesoporous NaX zeolite, which was templated by cationic templated polymer (polydiallyldimethylammonium chloride, PDADMAC) with two different length chains, was investigated. The structural properties of the zeolites were characterized by X-ray diffraction (XRD) and nitrogen adsorption analysis. The chemical activities of different zeolites toward the decomposition of TPP were determined with solid state 31P NMR spectra. After exposure of zeolites to TPP was sufficient and equilibrium was reached, a stoichiometric amount of water was also adsorbed and hydrolysis was observed. The TPP decomposition yields in different NaX zeolites were compared.

scholarly journals COMPOSITION, STRUCTURE AND TEXTURAL CHARACTERISTICS OF DOMESTIC ACID ACTIVATED BENTONITE

2014 ◽  
Vol 5 (1) ◽  
Author(s):  
Zоrаn Pеtrоvić ◽  
Pеrо Dugić ◽  
Vојislаv Аlеksić ◽  
Sаbinа Bеgić ◽  
Vlаdаn Мićić ◽  
...  
Keyword(s):  
Sulfuric Acid ◽  
Low Temperature ◽  
Layered Structure ◽  
Nitrogen Adsorption ◽  
X Ray Diffraction ◽  
Textural Characteristics ◽  
X Ray ◽  
Before And After ◽  
Activated Bentonite ◽  
Composition Structure

Bentonites are aluminosilicate minerals which, due to their porosity, layered structure and composition have a wide application. Structural and textural characteristics of bentonite may be improved by different modification procedures. The aim of this study was to investigate compositional, structural and textural characteristics of domestic bentonite in place Gerzovo, before and after the activation with sulfuric acid. These characteristics were investigated by analytical methods, X-ray diffraction (XRD) and the method of low-temperature nitrogen adsorption (BET). Characteristics of acid-activated bentonite were compared with the characteristics of commercial active clay. The obtained results showed that the activation of bentonite with sulfuric acid leads to a significant improvement in structural and textural characteristics. Using these results it can be assumed that this bentonite will have good adsorption characteristics and can serve as an alternative in comparison with imported commercial aluminosilicate-based adsorbents.

Structural and surface aspects of thermally treated copper aluminium mixed hydroxides

1991 ◽  
Vol 69 (10) ◽  
pp. 1511-1515 ◽  
Author(s):  
Awad I. Ahmed ◽  
S. E. Samra ◽  
S. A. El-Hakam
Keyword(s):  
Pore Structure ◽  
Copper Content ◽  
Textural Properties ◽  
Nitrogen Adsorption ◽  
Phase Changes ◽  
X Ray Diffraction ◽  
X Ray ◽  
Surface Areas ◽  
Structure Surface ◽  
Adsorption Desorption

CuO–Al2O3 catalysts containing various amounts of copper oxide have been prepared by precipitation. The phase changes were studied by X-ray diffraction. The results obtained revealed that the thermal treatment of solid CuO–Al2O3 at 700 °C produced only crystalline CuO. Heating to 900 °C led to the formation of copper alumina spinel together with unreacted CuO and γ-Al2O3. The spinel content was found to increase with increasing copper content. Nitrogen adsorption–desorption isotherms on the calcined samples have been measured. Surface areas have been calculated and the pore structure analysed. The textural properties of the system were found to depend on both the copper content and the calcination temperature. Key words: CuO, Al2O3 catalysts, structure, surface area, pore structure.

Hot-mesh Chemical Vapor Deposition for 3C-SiC Growth on Si and SiO2

2005 ◽  
Vol 862 ◽  
Author(s):  
Kanji Yasui ◽  
Jyunpei Eto ◽  
Yuzuru Narita ◽  
Masasuke Takata ◽  
Tadashi Akahane
Keyword(s):  
Chemical Vapor Deposition ◽  
Vapor Deposition ◽  
Chemical Vapor ◽  
X Ray Diffraction ◽  
Rocking Curve ◽  
Mesh Structure ◽  
X Ray ◽  
Si Substrates ◽  
Substrate Temperatures ◽  
Sic Films

AbstractThe crystal growth of SiC films on (100) Si and thermally oxidized Si (SiO2/Si) substrates by hot-mesh chemical vapor deposition (HMCVD) using monomethylsilane as a source gas was investigated. A mesh structure of hot tungsten (W) wire was used as a catalyzer. At substrate temperatures above 750°C and at a mesh temperature of 1600°C, 3C-SiC crystal was epitaxially grown on (100) Si substrates. From the X-ray rocking curve spectra of the (311) peak, SiC was also epitaxially grown in the substrate plane. On the basis of the X-ray diffraction (XRD) measurements, on the other hand, the growth of (100)-oriented 3C-SiC films on SiO2/Si substrates was determined to be achieved at substrate temperatures of 750-800°C, while polycrystalline SiC films, at substrate temperatures above 850°C. From the dependence of growth rate on substrate temperature and W-mesh temperature, the growth mechanism of SiC crystal by HMCVD was discussed.

scholarly journals Industrial Waste Utilization of Carbon Dust in Sustainable Cementitious Composites Production

Materials ◽  
2020 ◽  
Vol 13 (15) ◽  
pp. 3295
Author(s):  
Mohammad R. Irshidat ◽  
Nasser Al-Nuaimi
Keyword(s):  
Compressive Strength ◽  
Industrial Waste ◽  
Cement Mortar ◽  
Waste Utilization ◽  
Cementitious Composites ◽  
X Ray Diffraction ◽  
Sem Images ◽  
Compact Structure ◽  
X Ray ◽  
Industrial Waste Utilization

This paper experimentally investigates the effect of utilization of carbon dust generated as an industrial waste from aluminum factories in cementitious composites production. Carbon dust is collected, characterized, and then used to partially replace cement particles in cement mortar production. The effect of adding different dosages of carbon dust in the range of 5% to 40% by weight of cement on compressive strength, microstructure, and chemical composition of cement mortar is investigated. Scanning electron microscopy (SEM), X-ray diffraction (XRD), and X-ray fluorescence (XRF) analysis are used to justify the results. Experimental results show that incorporation of carbon dust in cement mortar production not only reduces its environmental side effects but also enhances the strength of cementitious composites. Up to 10% carbon dust by weight of cement can be added to the mixture without adversely affecting the strength of the mortar. Any further addition of carbon dust would decrease the strength. Best enhancement in compressive strength (27%) is achieved in the case of using 5% replacement ratio. SEM images show that incorporation of small amount of carbon dust (less than 10%) lead to produce denser and more compact-structure cement mortar.

scholarly journals Bulk Versus Surface Modification of Alumina with Mn and Ce Based Oxides for CH4 Catalytic Combustion

Materials ◽  
2019 ◽  
Vol 12 (11) ◽  
pp. 1771 ◽  
Author(s):  
Stefan Neatu ◽  
Mihaela M. Trandafir ◽  
Adelina Stănoiu ◽  
Ovidiu G. Florea ◽  
Cristian E. Simion ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Catalytic Combustion ◽  
Mixed Oxides ◽  
Sol Gel ◽  
Nitrogen Adsorption ◽  
X Ray Diffraction ◽  
X Ray ◽  
Temperature Programmed ◽  
Catalytic Combustion Of Methane ◽  
Adsorption Desorption

This study presents the synthesis and characterization of lanthanum-modified alumina supported cerium–manganese mixed oxides, which were prepared by three different methods (coprecipitation, impregnation and citrate-based sol-gel method) followed by calcination at 500 °C. The physicochemical properties of the synthesized materials were investigated by various characterization techniques, namely: nitrogen adsorption-desorption isotherms, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and H2–temperature programmed reduction (TPR). This experimental study demonstrated that the role of the catalytic surface is much more important than the bulk one. Indeed, the incipient impregnation of CeO2–MnOx catalyst, supported on an optimized amount of 4 wt.% La2O3–Al2O3, provided the best results of the catalytic combustion of methane on our catalytic micro-convertors. This is mainly due to: (i) the highest pore size dimensions according to the Brunauer-Emmett-Teller (BET) investigations, (ii) the highest amount of Mn4+ or/and Ce4+ on the surface as revealed by XPS, (iii) the presence of a mixed phase (Ce2MnO6) as shown by X-ray diffraction; and (iv) a higher reducibility of Mn4+ or/and Ce4+ species as displayed by H2–TPR and therefore more reactive oxygen species.

Characterization of Shivirtui Zeolite Modified with Aluminum Oxyhydroxide Nanofibers

2019 ◽  
Vol 942 ◽  
pp. 40-49
Author(s):  
Yulia Murashkina ◽  
Olga B. Nazarenko
Keyword(s):  
Chemical Properties ◽  
Nitrogen Adsorption ◽  
X Ray Diffraction ◽  
Scanning Electronic Microscopy ◽  
Electronic Microscopy ◽  
X Ray ◽  
Physical And Chemical ◽  
And Chemical Properties ◽  
Aluminum Oxyhydroxide

Natural zeolite of Shivirtui deposit (Russia) was modified with nanofibers of aluminum oxyhydroxide AlOOH. Aluminum oxyhydroxide nanofibers were produced at the heating and oxidation of aluminum powder with water. The properties of modified zeolite were investigated by means of X-ray diffraction, transmission electronic microscopy, scanning electronic microscopy, low-temperature nitrogen adsorption, thermal analysis, and Fourier transform infrared spectroscopy. It was found that water content in the modified sample of zeolite was about 15 %. Based on the study of the physical and chemical properties, shivirtui zeolite modified with nanofibers of aluminum oxyhydroxide can be proposed for use as a flame-retardant additive to polymers.

Sign in / Sign up

Export Citation Format

Share Document