scholarly journals Influence of Alkaline Activators on Unconfined Compressive Strength of Saline Soils Stabilised with Ground Granulated Blast Furnace Slags

2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Guoqi Xing ◽  
Lijun Zhang ◽  
Wei Xuan ◽  
Yueyue Pan ◽  
Yue Zhao ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Unconfined Compressive Strength ◽  
Saline Soils ◽  
Hydration Reaction ◽  
Hydration Products ◽  
Nonrenewable Resource ◽  
Cement Production ◽  
Study Results ◽  
Alkali Activated

To mitigate the environmental impact induced by CO2 emissions and nonrenewable resource consumption, which are typically associated with Portland cement production, ground granulated blast furnace slags (GGBSs) are usually added to the cement. In this study, the stabilisation effect of alkali-activated GGBS on saline soil and the hydration products of alkali-activated GGBS were investigated by unconfined compressive strength tests and scanning electron microscopy, respectively. The results show that Ca(OH)2 and NaOH as alkaline activators for GGBS significantly improve the unconfined compressive strength of saline soils. This strength is also enhanced by Na2SO4; however, the increase is considerably less than that provided by Ca(OH)2 and NaOH. In contrast, Na2CO3 is not a suitable alkaline activator for GGBS and has no significant effect on the unconfined compressive strength of saline soils. The study results further show that the morphology of hydration products varies because of the different alkaline activators involved in the hydration reaction with GGBS in saline soils.

scholarly journals Effect of Sodium Aluminate Dosage as a Solid Alkaline Activator on the Properties of Alkali-Activated Slag Paste

2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Bin Chen ◽  
Jun Wang ◽  
Jinyou Zhao
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Setting Time ◽  
Sodium Aluminate ◽  
Hydration Reaction ◽  
Hydration Products ◽  
Alkali Activated Slag ◽  
Alkaline Activator ◽  
Activated Slag ◽  
Alkali Activated

Extensive research into alkali-activated slag as a green gel material to substitute for cement has been done because of the advantages of low-carbon dioxide emissions and recycling of industrial solid waste. Alkali-activated slag usually has good mechanical properties, but the too fast setting time restricted its application and promotion. Changing the composition of alkaline activator could optimize setting time, usually making it by adding sodium carbonate or sodium sulfate but this would cause insufficient hydration reaction power and hinder compressive strength growth. In this paper, the effect of sodium aluminate dosage as an alkaline activator on the setting time, fluidity, compressive strength, hydration products, and microstructures was studied through experiments. It is fair to say that an appropriate amount of sodium aluminate could obtain a suitable setting time and better compressive strength. Sodium aluminate provided enough hydroxyl ions for the paste to promote the hydration reaction process that ensured obtaining high compressive strength and soluble aluminium formed precipitate wrapped on the surface of slag to inhibit the hydration reaction process in the early phase that prolonged setting time. The hydration mechanism research found that sodium aluminate played a key role in the formation of higher cross-linked gel hydration products in the late phase of the process. Preparing an alkali-activated slag with excellent mechanical properties and suitable setting time will significantly contribute to its application and promotion.

scholarly journals Red Mud-Blast Furnace Slag-Based Alkali-Activated Materials

2021 ◽  
Vol 13 (20) ◽  
pp. 11298
Author(s):  
Alessio Occhicone ◽  
Mira Vukčević ◽  
Ivana Bosković ◽  
Claudio Ferone
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Red Mud ◽  
Blast Furnace Slag ◽  
Bauxite Residue ◽  
Sodium Silicate Solution ◽  
Silicate Solution ◽  
Waste Products ◽  
Furnace Slag ◽  
Alkali Activated

The aluminum Bayer production process is widespread all over the world. One of the waste products of the Bayer process is a basic aluminosilicate bauxite residue called red mud. The aluminosilicate nature of red mud makes it suitable as a precursor for alkali-activated materials. In this work, red mud was mixed with different percentages of blast furnace slag and then activated by sodium silicate solution at different SiO2/Na2O ratios. Obtained samples were characterized by chemical–physical analyses and compressive strength determination. Very high values of compressive strength, up to 50 MPa, even for high percentage of red mud in the raw mixture (70 wt.% of RM in powder mixture), were obtained. In particular, the higher compressive strength was measured for cubic samples containing 50 wt.% of RM, which showed a value above 70 MPa. The obtained mixtures were characterized by no or scarce environmental impact and could be used in the construction industry as an alternative to cementitious and ceramic materials.

scholarly journals Geopolymer Based on Mechanically Activated Air-cooled Blast Furnace Slag

Materials ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1134 ◽  
Author(s):  
Ilda Tole ◽  
Magdalena Rajczakowska ◽  
Abeer Humad ◽  
Ankit Kothari ◽  
Andrzej Cwirzen
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Portland Cement ◽  
Sodium Silicate ◽  
Blast Furnace Slag ◽  
Ball Mill ◽  
Efficient Solution ◽  
Building Materials ◽  
Furnace Slag ◽  
Alkali Activated

An efficient solution to increase the sustainability of building materials is to replace Portland cement with alkali-activated materials (AAM). Precursors for those systems are often based on water-cooled ground granulated blast furnace slags (GGBFS). Quenching of blast furnace slag can be done also by air but in that case, the final product is crystalline and with a very low reactivity. The present study aimed to evaluate the cementitious properties of a mechanically activated (MCA) air-cooled blast furnace slag (ACBFS) used as a precursor in sodium silicate alkali-activated systems. The unreactive ACBFS was processed in a planetary ball mill and its cementing performances were compared with an alkali-activated water-cooled GGBFS. Mixes based on mechanically activated ACBFS reached the 7-days compressive strength of 35 MPa and the 28-days compressive strength 45 MPa. The GGBFS-based samples showed generally higher compressive strength values.

Alkali Activation of Granulated Blast Furnace Slag

2010 ◽  
Vol 158 ◽  
pp. 1-11 ◽  
Author(s):  
Zi Qiao Jin ◽  
Xian Jun Lu ◽  
Shu Gang Hu
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Portland Cement ◽  
Blast Furnace Slag ◽  
Ordinary Portland Cement ◽  
Hydration Product ◽  
Early Age ◽  
Hydration Products ◽  
Granulated Blast Furnace Slag ◽  
Furnace Slag

In order to stimulate the potential cementitious property of granulated blast furnace slag (GBFS), the ground GBFS sample (Wei Fang Iron and Steel Corporation, China) was activated by lime and gypsum under different dosages. The results showed that lime is an effective activator for the slag, and the optimum dosage of lime is about 10% (w/w) of the slag. At the optimum dosage of lime, the 28 days compressive strength of the lime-slag paste is higher than that of 32.5 ordinary Portland cement (OPC). But, the early age strength (3 and 7 days compressive strength) of the lime-slag paste is lower than that of the OPC. Addition of gypsum can effectively improve the early age strength of the lime-slag paste. At the ratio of gypsum:lime:slag of 8.2:9.2:82.6 (w/w), both the early and long-term compressive strengths of the gypsum-lime-slag paste are higher than that of the OPC. According to XRD, TG-DTA and SEM detections of the hydration products of the lime-slag paste, the gypsum-lime-slag paste and the OPC paste, it reveals that the hydration process of the GBFS-based cementitious material is different from the ordinary Portland cement and the presence of ettringite (AFt) contributes to the early age strength of the pastes. The major hydration product of the OPC paste (<7 days) were measured as ettringite (AFt), but the AFt phase was not detected in the hydration product of the lime-slag paste and the major hydration product of the lime-slag paste was determined as amorphous CSH gel. However, AFt was detected in the hydration products of the gypsum-lime-slag paste in the early stages of hydration, and the formation of AFt is favorable for the early strength improvement of the material.

scholarly journals Mechanism of Alkali-Activated Copper-Nickel Slag Material

2020 ◽  
Vol 2020 ◽  
pp. 1-10 ◽  
Author(s):  
Tingting Zhang ◽  
Haoliang Jin ◽  
Lijie Guo ◽  
Wenchen Li ◽  
Junan Han ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Testing Machine ◽  
Raw Material ◽  
Hydration Reaction ◽  
Reaction Products ◽  
X Ray Diffraction ◽  
Copper Nickel ◽  
Activating Agent ◽  
Cementing Material ◽  
Alkali Activated

A copper-nickel slag-based alkali-activated cementing material (CNSCM) for backfilling was prepared using copper-nickel slag as a raw material and sodium silicate (SS) as an activating agent. The effects of SS content (6%, 8%, and 10%) and curing humidity on the compressive strength of CNSCM were investigated using an electronic universal testing machine. Types of hydration products and microstructures were analyzed by X-ray diffraction, Fourier transform infrared spectroscopy, and scanning electron microscopy. The results indicated that by increasing the SS content, the compressive strength of the CNSCM exhibited an increasing trend, followed by a decreasing trend. The optimal content was 8%. Humidity was identified as another factor affecting compressive strength, which reached 17 MPa after curing for 28 d under standard conditions. A decrease in humidity could improve the compressive strength of the material. The main hydration reaction products of the CNSCM were C-S-H gel, Fe (OH)2 or Fe (OH)3 gel, and CaCO3.

scholarly journals Microstructural and Mechanical Properties of Alkali Activated Materials from Two Types of Blast Furnace Slags

Materials ◽  
2019 ◽  
Vol 12 (13) ◽  
pp. 2089 ◽  
Author(s):  
Jun Xing ◽  
Yingliang Zhao ◽  
Jingping Qiu ◽  
Xiaogang Sun
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Blast Furnace ◽  
Thermal Stabilization ◽  
Hydration Process ◽  
Reaction Products ◽  
Basic Oxide ◽  
X Ray ◽  
Physical And Chemical ◽  
Alkali Activated

This paper investigated the effect of blast furnace slags (BFS) characteristics on the properties achievement after being alkali activated. The physical and chemical characteristics of BFS were determined by X-ray fluorescence (XRF), X-ray Diffraction (XRD) and laser granulometry. Multi-technical characterizations using calorimetry, XRD, Fourier Transform Infrared Spectroscopy (FTIR), Thermogravimetry (TG-DTG), scanning electron microscope (SEM), nitrogen sorption and uniaxial compressive strength (UCS) were applied to give an in-depth understanding of the relationship between the reaction products, microstructure and BFS characteristics. The test results show that the microstructure and mechanical properties of alkali activated blast furnace slags (BFS) highly depend on the characteristics of BFS. Although the higher content of basic oxide could accelerate the hydration process and result in higher mechanical properties, a poor thermal stabilization was observed. On the other hand, with a higher content of Fe, the hydration process in alkali activated BFS2 lasts for a longer time, contributing to a delayed compressive strength achievement.

Research on Mechanism of Architectural Wastes Solidified by Alkali-Activated Cement and Fly Ash

2012 ◽  
Vol 446-449 ◽  
pp. 2708-2713 ◽  
Author(s):  
Qin Li ◽  
Xiao Jun Zhou ◽  
Zhuo Yin Jiang ◽  
Ke Wei Sun
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Hydration Products ◽  
Testing Methods ◽  
Fly Ashes ◽  
Comparison Research ◽  
Cement System ◽  
Cementitious System ◽  
Micro Morphology ◽  
Alkali Activated

An comparison research on the effect of pozzolanic reactions of fly ashes in architectural wastes recycle is described in the paper. In the experiment, NaOH and Na2SO4-Ca(OH)2 were used to activate the pozzolanic activities in the fly ashes—cement system to solidify the architectural wastes. The macro and micro testing methods were used to test the compressive strength, phase and electronic micro morphology of the hydration of alkali-activated fly ashes—cement cementitious system. The testing result shows that proper alkali-activated fly ashes—cement cementitious architectural wastes can shorten the incubation time of the pozzolanic reactions of fly ashes, whi ch make the reactions of fly ashes more sufficient. So the hydration products of fly ashes —cement cementitious system with alkali additions were more than those of without alkali add itions, and the compressive strength of the alkali-activated fly ashes—cement cementitious system is higher than that of non alkali-activated fly ashes—cement cementitious system.

High Strength Alkali Activated Slag Cements with Controlled Setting Times and Early Strength Gain

2015 ◽  
Vol 1100 ◽  
pp. 44-49 ◽  
Author(s):  
Pavel Krivenko ◽  
Oleg Petropavlovsky ◽  
Vit Petranek ◽  
Vasiliy Pushkar ◽  
Grigorii Vozniuk
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Water Glass ◽  
High Strength ◽  
Strength Gain ◽  
Setting Times ◽  
Alkaline Activator ◽  
Early Strength ◽  
Activated Slag ◽  
Alkali Activated

The paper discusses approaches to compositional build-up of high strength alkali activated cements made using water glass as alkaline activator represented by commercial products in a form of powder and liquid. The purpose was to study the influence of fineness of ground granulated blast-furnace slags, admixtures and additives, compatible with alkali activated cements, water glass and mode of manufacturing technology in order to reach high compressive strength (≥ 80 MPa at standard age (28 days)) and early strength (≥ 20 MPa after 3 h of hardening in normal conditions).

Sign in / Sign up

Export Citation Format

Share Document