scholarly journals Experimental Study on Freeze-Thaw Effects on Creep Characteristics of Rubber Concrete

2022 ◽  
Vol 2022 ◽  
pp. 1-14
Author(s):  
Qi Li ◽  
Fei Xu ◽  
Hemin Zheng ◽  
Junhao Shi ◽  
Jianyu Zhang
Keyword(s):  
Compressive Strength ◽  
Elastic Modulus ◽  
Stress Level ◽  
Creep Behavior ◽  
Mass Loss Rate ◽  
Crumb Rubber ◽  
Dynamic Elastic Modulus ◽  
Freeze Thaw ◽  
Stress Levels ◽  
Rubber Concrete

Crumb Rubber Concrete (CRC) can exhibit high freeze-thaw resistance, but its long-term creep behavior under various freeze-thaw conditions remains unclear, which is essential for the safety of pavement engineering in the severe cold zone. In this study, the freeze-thaw effects on the creep behavior of CRC under different stress levels were systematically analyzed by testing the compressive strength, the uniaxial creep under different stress levels, and the dynamic elastic modulus. To simulate real conditions of the road environment in the cold area, the lowest temperature of −20°C, six freeze-thaw cycles of 0, 30, 60, 90, 120, and 150, and seven different stress levels of 0.4, 0.5, 0.6, 0.7, 0.8, and 0.9 of the compressive strength were employed in this study. The test results showed that the mass loss rate was 6%–11.2% and the compressive strength decreased by 6.51%–47% after 30–150 freeze-thaw cycles. When the stress level reached its critical value, the relative dynamic elastic modulus decreased with the number of freeze-thaw cycles. After 150 freeze-thaw cycles, failure did not appear when the stress level was lower than 50%, above which the creep failure was determined by the stress level and the number of the freeze-thaw cycles. Meanwhile, it was found that the cracking and interfacial debonding between the matrix and the crumb rubber particle were the main reasons for the degradation of CRC creep performance. Finally, a Weibull distribution-based empirical creep damage model was established to predict the failure of CRC, which can enhance its application to related engineering.

scholarly journals Experimental Investigation on the Freeze–Thaw Resistance of Steel Fibers Reinforced Rubber Concrete

Materials ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1260
Author(s):  
Tao Luo ◽  
Chi Zhang ◽  
Chaowei Sun ◽  
Xinchao Zheng ◽  
Yanjun Ji ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Elastic Modulus ◽  
Mass Loss ◽  
Loss Rate ◽  
Bending Strength ◽  
Mass Loss Rate ◽  
Steel Fibers ◽  
Freeze Thaw ◽  
Four Point Bending ◽  
Rubber Concrete

The reuse of rubber in concrete results in two major opposing effects: an enhancement in durability and a reduction in mechanical strength. In order to strengthen the mechanical properties of rubber concrete, steel fibers were added in this research. The compressive strength, the four-point bending strength, the mass loss rate, and the relative dynamic elastic modulus of steel fiber reinforced rubber concrete, subjected to cyclic freezing and thawing, were tested. The effects of the content of steel fibers on the freeze–thaw resistance are discussed. The microstructure damage was captured and analyzed by Industrial Computed Tomography (ICT) scanning. Results show that the addition of 2.0% steel fibers can increase the compressive strength of rubber concrete by 26.6% if there is no freeze–thaw effect, but the strengthening effect disappears when subjected to cyclic freeze–thaw. The enhancement of steel fibers on the four-point bending strength is effective under cyclic freeze–thaw. The effect of steel fibers is positive on the mass loss rate but negative on the relative dynamic elastic modulus.

scholarly journals Analysis and Prediction of Compressive Properties for Steel Fiber-and-Nanosilica-Reinforced Crumb Rubber Concrete

2020 ◽  
Vol 2020 ◽  
pp. 1-15
Author(s):  
Danying Gao ◽  
Tao Zhang ◽  
Yihong Wang ◽  
Yiming Kong ◽  
Dawei Li ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Elastic Modulus ◽  
Volume Content ◽  
Steel Fiber ◽  
Crumb Rubber ◽  
Steel Fibers ◽  
Peak Strain ◽  
Compressive Properties ◽  
Crumb Rubber Concrete ◽  
Rubber Concrete

The disposal of waste tire rubber has gained more attention from the viewpoint of green, environmental protection, and sustainability. Numerous attempts have been stated on the properties of crumb rubber concrete (CRC) and observed that there is a large reduction of compressive strength and elastic modulus of CRC with the increase of the rubber substitution rate. Based on the CRC with the crumb rubber volume content of 5%, the steel fibers and nanosilica were added to CRC to make steel fiber-and-nanosilica-reinforced crumb rubber concrete (SFNS-CRC) in this paper. The effects of the steel fiber volume content and nanosilica content on the compressive properties of SFNS-CRC were studied, including compressive strength, elastic modulus, peak strain, compression toughness, and failure pattern. The test results indicated that the modulus of elasticity and compressive strength of SFNS-CRC have the increasing tendency with the addition of steel fibers and nanosilica. Moreover, the peak strains have a significant increase with the increase of the steel fiber content and nanosilica replacement ratio. The compressive stress-strain curves of SFNS-CRC gradually plump with the increase of the steel fibers and nanosilica. Finally, the prediction formulas for the compressive strength, elastic modulus, and peak strain of SFNS-CRC were set up. A simple predicted model of the stress-strain curve for SFNS-CRC was proposed, which considers the effect of steel fibers and nanosilica.

scholarly journals Mechanical Properties and Micro Structure of Cement Concrete in Freeze-Thaw Environment

2021 ◽  
Vol 233 ◽  
pp. 01011
Author(s):  
Xin jian Lv ◽  
Lei Yu ◽  
Ming ming Chai
Keyword(s):  
Compressive Strength ◽  
Elastic Modulus ◽  
Pore Structure ◽  
Fresh Water ◽  
Pore Diameter ◽  
Dynamic Elastic Modulus ◽  
Freeze Thaw ◽  
Salty Water ◽  
Thaw Cycle ◽  
Freeze Thaw Cycle

In order to find the declay law of mechanical property and the performance difference after salty water and fresh water freeze-thaw cycle, freeze-thaw cycle environments under the salty water and fresh water are simulated. The compressive strength, dynamic elastic modulus and the mass lost are tested. The pore structure parameters are also tested by MIP. Plot the pore diameter distribution curve. The result shows that the compressive strength and dynamic elastic modulus are all decreased. The degree of these two properties decreasing under salty water freeze and thaw recycle is more than the one under fresh water. The parameters of porosity and critical pore diameter become larger. The amount of pores whose diameter is between 100nm and 1000nm increase. The amount of pores whose diameter is under 100nm decrease. The deteriorate degree of pore structure is deeper in salty water than in fresh water.

Performance Comparison between High Strength Concrete and Ordinary Concrete under Mixed Erosion and Freeze-Thaw Cycling

2010 ◽  
Vol 163-167 ◽  
pp. 1667-1672
Author(s):  
Jian Zhang ◽  
Bo Diao ◽  
Yan Dong Li ◽  
Xiao Ning Zheng
Keyword(s):  
Compressive Strength ◽  
Elastic Modulus ◽  
High Strength Concrete ◽  
Mass Loss Rate ◽  
Peak Stress ◽  
High Strength ◽  
Performance Comparison ◽  
Freeze Thaw ◽  
Strength Concrete ◽  
Ordinary Concrete

: Performance of high strength concrete and ordinary concrete under alternating action of mixed erosion and freeze-thaw cycling were compared. The erosion solution was mixed by weight of 3% sodium chloride and 5% sodium sulfate. Results showed that, after 200 freeze-thaw cycles, the effect of surface scaling of ordinary concrete was more significant than that of high strength concrete, and the mass loss rate of ordinary concrete was much higher; The relative dynamic modulus of elasticity of high strength concrete slightly increased by 2.99%, while that of ordinary concrete decreased more than 13%. Compressive strength and elastic modulus of high strength and ordinary concrete behaved almost in the same way in the first 50 freeze-thaw cycles, with the increase of freeze-thaw cycles in the following test, the compressive strength and elastic modulus of ordinary concrete showed larger reductions than these of high strength concrete. As the freeze-thaw cycles increased, the corresponding strain to the peak stress of high strength concrete decreased, but it increased for ordinary concrete.

scholarly journals Experimental Study on the Durability of Alkali-Activated Slag Concrete after Freeze-Thaw Cycle

2021 ◽  
Vol 2021 ◽  
pp. 1-19
Author(s):  
Bin Chen ◽  
Jun Wang
Keyword(s):  
Compressive Strength ◽  
Elastic Modulus ◽  
Raw Material ◽  
Dynamic Elastic Modulus ◽  
Important Indicator ◽  
Alkali Activated Slag ◽  
Freeze Thaw ◽  
Thaw Cycle ◽  
Activated Slag ◽  
Alkali Activated

A freeze-thaw resistance is an important indicator of the durability of alkali-activated slag concrete, which causes structural failure when the performance is low, especially in severely cold areas. In this study, solid sodium aluminate and sodium silicate were used as composite alkaline activators, while slag was used as the raw material to prepare alkali-activated slag concrete, whose freeze-thaw resistance, as well as that of ordinary cement concrete, was experimentally studied by varying the freeze-thaw cycles. The effects of the mass, compressive strength, and dynamic elastic modulus of the sample were investigated by considering the influence of different water-to-slag ratios and slag contents, while the damage variables and model were also analyzed. The results showed that alkali-activated slag concrete had an excellent freeze-thaw resistance, which was significantly affected by the water-to-slag ratio and compressive strength; specifically, the higher the water-to-slag ratio, the lower the freeze-thaw resistance, and the higher the compressive strength, the better the freeze-thaw resistance. The freeze-thaw durability, microstructure, and damage mechanism were studied via microscopic analysis. When analyzed via the microstructure test, crack pores and microcracks with narrow spaces and large surface areas were generated under freeze-thaw damage conditions, but the dense hydration structure and high-bonding-strength hydration products led to a better freeze-thaw resistance. The damage model was established using compressive strength and relative dynamic elastic modulus as damage variables, and the attenuation exponential and accumulative damage power function model had a high accuracy, which could better reflect the freeze-thaw damage law and damage degree and predict the lifetime of alkali-activated slag concrete.

Experimental Study on Frost Resistance Properties of Pumice Mixed Aggregate Concrete

2012 ◽  
Vol 476-478 ◽  
pp. 1661-1664
Author(s):  
Jun Fang Huo ◽  
Jian Jun Chu ◽  
Hui Yang
Keyword(s):  
Elastic Modulus ◽  
Mass Loss ◽  
Frost Resistance ◽  
Loss Rate ◽  
Mass Loss Rate ◽  
Strength Loss ◽  
Dynamic Elastic Modulus ◽  
Aggregate Concrete ◽  
Freeze Thaw ◽  
Thaw Cycle

Different amount of pumice were used to replace gravel to make mixed aggregate concrete, the fast freeze-thaw cycle test were conducted and the influence of pumice rate substitution to the frost resistance properties of concrete were studied.The mass loss rate, strength loss and relative dynamic elastic modulus were regarded as the evaluation index of frost resistance properties of concrete. Results showed that the mass loss rate and strength loss rate gradually decreased and the relative dynamic elastic modulus gradually increased with the increase of pumice rate, the mass loss rate, strength loss rate and the relative dynamic elastic modulus gradually decreased with the increase of freeze-thaw cycles. Polypropylene fibers could reduce the strength loss rate, improved the relative dynamic elastic modulus, but had little effect to improve the mass loss. Through the frost resistance, the frost resistance of concrete improved with the increase of pumice content, at the same time, polypropylene fiber also could improve the frost resistance of concrete.

Studies the Properties of Polyaspartic Polyurea Coated Concrete under Coaction of Salt Fog and Freeze-Thaw

2012 ◽  
Vol 455-456 ◽  
pp. 781-785
Author(s):  
Ping Lu ◽  
Xin Mao Li ◽  
Xue Qiang Ma ◽  
Wei Bo Huang
Keyword(s):  
Elastic Modulus ◽  
Frost Resistance ◽  
Dynamic Elastic Modulus ◽  
Freeze Thaw ◽  
Decrease Rate ◽  
Thaw Cycle ◽  
Freeze Thaw Cycle ◽  
Salt Fog

. This paper mainly studied the properties of PAE polyurea coated concrete under coactions of salt fog and freeze-thaw. After exposed salt fog conditions for 200d, T3, B2, F2 and TM four coated concrete relative dynamic elastic modulus have small changes, but different coated concrete variation amplitude is different. T3 coated concrete after 100 times of freeze-thaw cycle the relative dynamic elastic modulus began to drop, 200 times freeze-thaw cycle ends, relative dynamic elastic modulus variation is the largest, decrease rate is 95%, TM concrete during 200 times freeze-thaw cycle, relative dynamic elastic modulus almost no change, B2 concrete and F2 concrete the extent of change between coating T3 and TM. After 300 times the freeze-thaw cycle coated concrete didn't appear freeze-thaw damage phenomenon. Four kinds of coating concrete relative dynamic elastic modulus variation by large to small order: T3 coated concrete > B2 coated concrete >F2 coated concrete > TM coated concrete, concrete with the same 200d rule. Frost resistance order, by contrast, TM coated concrete > B2 coated concrete > F2 coated concrete > T3 coated concrete.

Research on Mechanical Properties of Crumb Rubber Concrete

2011 ◽  
Vol 477 ◽  
pp. 290-295 ◽  
Author(s):  
Li Bo Bian ◽  
Shao Min Song
Keyword(s):  
Mechanical Properties ◽  
Wear Resistance ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Apparent Density ◽  
Crumb Rubber ◽  
Fatigue Performance ◽  
Brittleness Index ◽  
Mixing Ratio ◽  
Rubber Concrete

Considering large number production of the abandoned tyres and the question of the concrete with mixture of crumb rubber，the mainly task of this paper is to study the mechanical properties of different mixing ratio concrete with vary volume of crumb rubber. The results showed that the workability, apparent density, compressive strength, flexural strength and brittleness index decrease as the increase of crumb rubber. While the anti-crack performance and anti-fatigue performance can be improved. The wear-resistance properties are a little lower than common concrete.

scholarly journals Use of Silica Fume and GGBS to Improve Frost Resistance of ECC with High-Volume Fly Ash

2018 ◽  
Vol 2018 ◽  
pp. 1-11 ◽  
Author(s):  
Yushi Liu ◽  
Xiaoming Zhou ◽  
Chengbo Lv ◽  
Yingzi Yang ◽  
Tianan Liu
Keyword(s):  
Elastic Modulus ◽  
Sodium Chloride ◽  
Mass Loss ◽  
Frost Resistance ◽  
Chloride Solution ◽  
Sodium Chloride Solution ◽  
Tap Water ◽  
High Volume ◽  
Dynamic Elastic Modulus ◽  
Freeze Thaw

Fly ash (FA) has been an important ingredient for engineered cementitious composite (ECC) with excellent tensile strain capacity and multiple cracking. Unfortunately, the frost resistance of ECC with high-volume FA has always been a problem. This paper discusses the influence of silica fume (SF) and ground-granulated blast-furnace slag (GGBS) on the frost resistance of ECC with high volume of FA. Four ECC mixtures, ECC (50% FA), ECC (70% FA), ECC (30% FA + 40% SL), and ECC (65% FA + 5% SF), are evaluated by freezing-thawing cycles up to 200 cycles in tap water and sodium chloride solution. The result shows the relative dynamic elastic modulus and mass loss of ECC in sodium chloride solution by freeze-thaw cycles are larger than those in tap water by freeze-thaw cycles. Moreover, the relative dynamic elastic modulus and mass loss of ECC by freeze-thaw cycles increase with FA content increasing. However, the ECC (30% FA + 40% SL) shows a lower relative dynamic elastic modulus and mass loss, but its deflection upon four-point bending test is relatively smaller before and after freeze-thaw cycles. By contrast, the ECC (65% FA + 5% SF) exhibits a significant deflection increase with higher first cracking load, and the toughness increases sharply after freeze-thaw cycles, meaning ECC has good toughness property.

Experimental Study on Ratio of Bending-Compressive Strength of the Crumb Rubber Concrete Modified by Latex

2014 ◽  
Vol 941-944 ◽  
pp. 761-764
Author(s):  
Wei Li ◽  
Zhen Huang ◽  
Xiao Chu Wang ◽  
Zi Sheng Zang
Keyword(s):  
Mechanical Property ◽  
Experimental Study ◽  
Compressive Strength ◽  
Surface Modification ◽  
Flexural Strength ◽  
Crumb Rubber ◽  
Interface Effect ◽  
Rubber Particles ◽  
Crumb Rubber Concrete ◽  
Rubber Concrete

The cementitiousness between rubber particles and cement-based material could be raised because of the surface modification of rubber,thus enhance the mechanical property of crumb rubber concrete and improve the interface effect of rubber particles.We had researched the change regulation about the ratio of bending-compressive strength of the crumb rubber concrete modified by latex,the concrete with various quantity of rubber,under the condition dosage of latex is 0.5% of cement quality.The result of experimental prove that,compressive strength, splitting tensile and flexural strength could be enhanced because of latex injecting,and the ratio of bending-compressive strength could be enhanced at the same time.

Sign in / Sign up

Export Citation Format

Share Document