Direct Writing on Paper Substrate to Prepare Silver Electrode Structures for Flexible Sensors

2021 ◽  
Vol 21 (12) ◽  
pp. 6048-6053
Author(s):  
Qi Wang ◽  
Mingwei Li ◽  
Yao Xie ◽  
Yun Ou ◽  
Weiping Zhou
Keyword(s):  
Low Cost ◽  
Rapid Development ◽  
Silver Electrode ◽  
Silver Nanostructures ◽  
Direct Writing ◽  
Paper Substrate ◽  
Electronic Products ◽  
Glass Substrates ◽  
Different Temperatures ◽  
Writing Technology

With the rapid development of the electronics industry, electronic products based on silicon and glass substrates electronic products will gradually be unable to meet the rising demand. Flexibility, environmental protection, and low costs are important for the development of electronic products. In this study, an efficient and low-cost method for preparing silver electrode structures by direct writing on paper has been demonstrated. Based on this method, a flexible paper-based sensor was prepared. The liquid printing ink used mainly comprises a precursor liquid without pre-prepared nanomaterials. The precursor liquid is transparent with good fluidity. Simple direct writing technology was used to write on the paper substrate using the precursor ink. When the direct-writing paper substrate was subsequently heated, silver nanostructures precipitated from the precursor liquid ink onto the paper substrate. The effect of different temperatures on the formation of the silver nanostructures and the influence of different direct writing processes on the structures were studied. Finally, a paper-based flexible sensor was prepared for finger-bending signal detection. The method is simple to operate and low in cost and can be used for the preparation of environment-friendly paper-based devices.

SYNTHESIS AND ETHANOL SENSING CHARACTERISTICS OF NANOSTRUCTURED MoO3:Zn THIN FILMS

2018 ◽  
Vol 25 (01) ◽  
pp. 1850046 ◽  
Author(s):  
SEYYED HAMID MOUSAVI-ZADEH ◽  
MOHAMMAD BAGHER RAHMANI
Keyword(s):  
Thin Films ◽  
Gas Sensing ◽  
Molybdenum Trioxide ◽  
Low Cost ◽  
Ethanol Vapor ◽  
Glass Substrates ◽  
Structure Changes ◽  
Recovery Times ◽  
Different Temperatures ◽  
Sensing Characteristics

In this research, gas sensing characteristics of undoped and zinc-doped molybdenum trioxide (MoO[Formula: see text] thin films toward ethanol vapor were investigated. Thin films were deposited using low cost and simple technique of spray pyrolysis on top of glass substrates at 450[Formula: see text]C. Effects of addition of Zn, as an impurity, on the surface morphology, structural and optical properties of MoO3 thin films were also investigated. X-ray diffraction (XRD) pattern analysis showed that by increasing the amount of impurity, crystal structure changes from orthorhombic [Formula: see text]-MoO3 to two new phases of monoclinic [Formula: see text]-ZnMoO4 and Mo5O[Formula: see text] reduced phase. Field emission scanning electron microscope (FESEM) images showed that by increasing the amount of impurity up to 5[Formula: see text]at.%, grain sizes decrease to about 60[Formula: see text]nm. UV–Vis analysis showed that by increasing the percentage of impurity the band gap of thin films increases. Gas sensing properties of samples were studied at three temperatures of 200[Formula: see text]C, 250[Formula: see text]C and 300[Formula: see text]C toward different concentrations of ethanol vapor. Gas response of 5[Formula: see text]at.% Zn-doped MoO3 thin film reached the maximum value of [Formula: see text]% when it exposed to 1000[Formula: see text]ppm of ethanol vapor. Response and recovery times for all samples were reported at different temperatures.

scholarly journals Microstructure and Thermoelectric Properties of (Bi0.48Sb1.52)Te3 Thick Films Prepared with Tape Casting Method

Electronics ◽  
2021 ◽  
Vol 10 (2) ◽  
pp. 140
Author(s):  
Lichen Liu ◽  
Ziping Cao ◽  
Min Chen ◽  
Jun Jiang
Keyword(s):  
Thermoelectric Properties ◽  
Low Cost ◽  
Thick Films ◽  
Tape Casting ◽  
Casting Process ◽  
Casting Method ◽  
Glass Substrates ◽  
Conductive Films ◽  
Casting Technology

This paper reports the fabrication and characterization of (Bi0.48Sb1.52)Te3 thick films using a tape casting process on glass substrates. A slurry of thermoelectric (Bi0.48Sb1.52)Te3 was developed and cured thick films were annealed in a vacuum chamber at 500–600 °C. The microstructure of these films was analyzed, and the Seebeck coefficient and electric conductivity were tested. It was found that the subsequent annealing process must be carefully designed to achieve good thermoelectric properties of these samples. Conductive films were obtained after annealing and led to acceptable thermoelectric performance. While the properties of these initial materials are not at the level of bulk materials, this work demonstrates that the low-cost tape casting technology is promising for fabricating thermoelectric modules for energy conversion.

scholarly journals A Multi-Loop Vehicle-Counting Method under Gray Mode and RGB Mode

2021 ◽  
Vol 11 (15) ◽  
pp. 6831
Author(s):  
Yue Chen ◽  
Jian Lu
Keyword(s):  
Intelligent Transportation Systems ◽  
High Efficiency ◽  
Road Traffic ◽  
Low Cost ◽  
Rapid Development ◽  
Intelligent Transportation ◽  
Transportation Systems ◽  
Counting Method ◽  
Moving Vehicle ◽  
Available Information

With the rapid development of road traffic, real-time vehicle counting is very important in the construction of intelligent transportation systems (ITSs). Compared with traditional technologies, the video-based method for vehicle counting shows great importance and huge advantages in its low cost, high efficiency, and flexibility. However, many methods find difficulty in balancing the accuracy and complexity of the algorithm. For example, compared with traditional and simple methods, deep learning methods may achieve higher precision, but they also greatly increase the complexity of the algorithm. In addition to that, most of the methods only work under one mode of color, which is a waste of available information. Considering the above, a multi-loop vehicle-counting method under gray mode and RGB mode was proposed in this paper. Under gray and RGB modes, the moving vehicle can be detected more completely; with the help of multiple loops, vehicle counting could better deal with different influencing factors, such as driving behavior, traffic environment, shooting angle, etc. The experimental results show that the proposed method is able to count vehicles with more than 98.5% accuracy while dealing with different road scenes.

The Design and Implementation of ECC High-Speed Encryption Engine Based on FPGA

2012 ◽  
Vol 459 ◽  
pp. 544-548 ◽  
Author(s):  
Wei Liang ◽  
Jian Bo Xu ◽  
Wei Hong Huang ◽  
Li Peng
Keyword(s):  
Data Transmission ◽  
High Speed ◽  
Lower Cost ◽  
Low Cost ◽  
Rapid Development ◽  
Security Technology ◽  
Multiplication Algorithm ◽  
Secure Data Transmission ◽  
And Performance ◽  
Computation Speed

Network security technology ensures secure data transmission in network. Meanwhile, it brings extra overhead of security system in terms of cost and performance, which seriously affects the rapid development of existing high-speed encryption systems. The existing encryption technology cannot meet the demand of high security, low cost and high real-time. For solving above problems, an ECC encryption engine architecture based on scalable public key cipher and a high-speed configurable multiplication algorithm are designed. The algorithm was tested on FPGA platform and the experiment results show that the system has better computation speed and lower cost overhead. By comparing with other systems, our system has benefits in terms of hardware overhead and encryption time ratio

scholarly journals Superior Degradation Performance of Nanoporous Copper Catalysts on Methyl Orange

Metals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 913
Author(s):  
Jinyi Wang ◽  
Sen Yang
Keyword(s):  
Activation Energy ◽  
Methyl Orange ◽  
High Efficiency ◽  
Low Cost ◽  
Degradation Process ◽  
Copper Catalysts ◽  
Reaction Rate Constant ◽  
Nanoporous Structure ◽  
Intra Particle Diffusion ◽  
Different Temperatures

The development of low-cost and high-efficiency catalysts for wastewater treatment is of great significance. Herein, nanoporous Cu/Cu2O catalysts were synthesized from MnCu, MnCuNi, and MnCuAl with similar ligament size through one-step dealloying. Meanwhile, the comparisons of three catalysts in performing methyl orange degradation were investigated. One of the catalysts possessed a degradation efficiency as high as 7.67 mg·g−1·min−1. With good linear fitting by the pseudo-first-order model, the reaction rate constant was evaluated. In order to better understand the degradation process, the adsorption behavior was considered, and it was divided into three stages based on the intra-particle diffusion model. Three different temperatures were applied to explore the activation energy of the degradation. As a photocatalytic agent, the nanoporous structure of Cu/Cu2O possessed a large surface area and it also had low activation energy, which were beneficial to the excellent degradation performance.

Thermal conversion of CBD grown ZnS thin films to ZnO

2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Kooliyankal Naseema ◽  
Kaniyamkandy Ribin ◽  
Nidiyanga Navya ◽  
Prasoon Prasannan
Keyword(s):  
Thin Films ◽  
Low Cost ◽  
Thermal Conversion ◽  
X Ray Diffraction ◽  
Xrd Pattern ◽  
Glass Substrates ◽  
Anion Substitution ◽  
Nano Crystalline ◽  
Before And After ◽  
Uv Visible

AbstractNano crystalline zinc sulfide thin films were deposited onto glass substrates by chemical bath deposition method. One of the samples was annealed at 300 °C for 2 h in air using a muffle furnace. The prepared thin films were investigated by X-ray diffraction (XRD), UV–visible spectroscopy (UV–vis), photoluminescence spectroscopy (PL), scanning electron microscopy (SEM) and Raman spectroscopy (FT-R) studies before and after annealing. The analysis confirmed the thermal-induced anion substitution and conversion of ZnS crystal to ZnO wurtzite crystal. XRD pattern showed that these films were phase pure and polycrystalline in nature. Optical band gap was found to be 3.86 eV for ZnS and 3.21 eV for ZnO. The films prepared by this simple, low-cost technique are suitable for photovoltaic and optoelectronic applications.

scholarly journals Fabrication of Porous Silicon Based Humidity Sensing Elements on Paper

2015 ◽  
Vol 2015 ◽  
pp. 1-10 ◽  
Author(s):  
Tero Jalkanen ◽  
Anni Määttänen ◽  
Ermei Mäkilä ◽  
Jaani Tuura ◽  
Martti Kaasalainen ◽  
...  
Keyword(s):  
Porous Silicon ◽  
Smart Cities ◽  
Low Cost ◽  
Electrical Characterization ◽  
Fabrication Process ◽  
Sensing Element ◽  
Paper Substrate ◽  
Roll To Roll ◽  
Silver Electrodes ◽  
Silicon Based

A roll-to-roll compatible fabrication process of porous silicon (pSi) based sensing elements for a real-time humidity monitoring is described. The sensing elements, consisting of printed interdigitated silver electrodes and a spray-coated pSi layer, were fabricated on a coated paper substrate by a two-step process. Capacitive and resistive responses of the sensing elements were examined under different concentrations of humidity. More than a three orders of magnitude reproducible decrease in resistance was measured when the relative humidity (RH) was increased from 0% to 90%. A relatively fast recovery without the need of any refreshing methods was observed with a change in RH. Humidity background signal and hysteresis arising from the paper substrate were dependent on the thickness of sensing pSi layer. Hysteresis in most optimal sensing element setup (a thick pSi layer) was still noticeable but not detrimental for the sensing. In addition to electrical characterization of sensing elements, thermal degradation and moisture adsorption properties of the paper substrate were examined in connection to the fabrication process of the silver electrodes and the moisture sensitivity of the paper. The results pave the way towards the development of low-cost humidity sensors which could be utilized, for example, in smart packaging applications or in smart cities to monitor the environment.

An application of high-temperature superconductors YBCO to magnetic separation

2017 ◽  
Vol 31 (25) ◽  
pp. 1745001 ◽  
Author(s):  
Qiudong Guo ◽  
Peng Zhang ◽  
Lin Bo ◽  
Guibin Zeng ◽  
Dengqian Li ◽  
...  
Keyword(s):  
Magnetic Field ◽  
High Temperature ◽  
Magnetic Separation ◽  
High Magnetic Field ◽  
Low Cost ◽  
Rapid Development ◽  
High Temperature Superconductors ◽  
New Approach ◽  
Industrial Areas ◽  
Ybco Tape

With the rapid development of manufacturing technology of high temperature superconductive YB[Formula: see text]Cu3O[Formula: see text] YBCO materials and decreasing in cost of production, YBCO is marching into industrial areas with its good performances as source of high-magnetic field and rather low cost in reaching superconductivity. Based on analysis of the performance of high temperature superconductors YBCO and development of technology in superconductive magnetic separation both home and abroad, we propose a new approach of taking YBCO tape to make a solenoid as the source of a high magnetic field of magnetic separatior of ores. The paper also looks into the future of the YBCO high temperature superconductive magnetic separation from the perspective of technology and cost, as well as its applications in other industries.

Mocvd SrS:Ce for Applications in Electroluminescent Devices

1997 ◽  
Vol 471 ◽  
Author(s):  
D. Endisch ◽  
K. Barth ◽  
J. Lau ◽  
G. Peterson ◽  
A. E. Kaloyeros ◽  
...  
Keyword(s):  
Process Development ◽  
Process Integration ◽  
Low Cost ◽  
Chemical Vapor ◽  
High Growth ◽  
Film Structure ◽  
High Growth Rate ◽  
Organic Chemical ◽  
Glass Substrates ◽  
Full Color

ABSTRACTSrS:Ce is an important material for full color electroluminescent (EL) flat panel displays. Using a combination of SrS:Ce/ZnS:Mn and appropriate color filters high quality full color displays have been demonstrated [1]. Major issues for commercially viable process integration of SrS:Ce are the combination of high luminance, high growth rate, and process temperatures below 600°C for compatibility with low cost glass substrates. This work describes the process development and optimization of metal-organic chemical vapor deposition (MOCVD) of SrS:Ce. MOCVD is a promising candidate for deposition of SrS:Ce because it can provide the required growth rates and allows control of crystal structure and stoichiometry. Growth of SrS:Ce was performed in the temperature range from 400°C to 530°C using Sr(tmhd)2, Ce(tmhd)4, and H2S as precursors. The structure of the SrS:Ce was found to be strongly dependent on the H2S flow. A brightness of 15 fL and an efficiency of 0.22 lm/W has been achieved (40 V above threshold voltage, 60 Hz AC). Film analysis included Rutherford backscattering (RBS), X-ray diffraction (XRD), atomic force microscopy (AFM), and EL measurements. Results on the correlation between process parameters, film structure, grain size and EL performance will be presented.

Recovery Value Metals from Mixed Spent Li-Ion Batteries

2014 ◽  
Vol 540 ◽  
pp. 267-271
Author(s):  
Xin Liu ◽  
Lin Yan Li ◽  
Fan Yun Zeng ◽  
Xue Jun Wang ◽  
Sheng Ming Xu
Keyword(s):  
Solvent Extraction ◽  
Raw Materials ◽  
Low Cost ◽  
Rapid Development ◽  
Li Ion Batteries ◽  
Active Materials ◽  
Solid Ratio ◽  
Li Ion ◽  
Leaching Condition ◽  
Addition Amount

With the rapid development and wide application of Li-ion batteries, cathode materials containing value metals Co, Ni and Mn are blended by several kind of metal oxide presently for pursuing high safe stability and low cost. The composition of spent Li-ion batteries has become complicated and optimum leaching condition varied. In this paper, leaching process for the mixture of pure LiCoO2and Li (Ni1/3Co1/3Mn1/3)O2was studied. With an increase in component of LiCoO2in mixed materials, the optimum leaching condition varied as: temperature from 60°C to 90°C, H2O2addition amount from 0.54 to 0.75ml/g and liquid-solid ratio from 10 to 20. According to this result, a real mixed spent batteries materials was recovered by being leached in 2M H2SO4at temperature of 90°C, liquid-solid ratio 20 and 0.6ml/g H2O2added. The leaching efficiencies of Co, Ni, Mn, Li were 96.88%, 93.71%, 92.12%, 99.43% respectively. Cu, Al and Fe in solution were removed by precipitation and solvent extraction. Finally, Ni, Co, Mn were extracted by D2EHPA for separating with Na+and other impurities, which is used as a raw materials for preparation of cathode active materials in batteries.

Sign in / Sign up

Export Citation Format

Share Document