Establishment of a digital simulated testing platform for radiation protection performance and preparation of three-layer coated flexible composites

2021 ◽  
pp. 004051752110028
Author(s):  
Guoyi Liu ◽  
Xiaoming Zhao ◽  
Yuanjun Liu ◽  
Yuhong Shen
Keyword(s):  
Thermal Conductivity ◽  
Thermal Radiation ◽  
Radiation Protection ◽  
Protective Coating ◽  
Base Material ◽  
Heat Radiation ◽  
Material Structure ◽  
Testing Platform ◽  
Flexible Composites ◽  
Test Platform

Fire proximity suits serve as the highest level of thermal protective clothing for firefighters when passing through the scene of a fire and within close range of open fire. A digital simulated testing platform for radiation protection performance was established based on the TPP701D thermal protective performance tester, by comparison of simulated data and measured results for the outer material of the fire proximity suit. Using single-, double- and three-layer flexible composites and the fabric as the base material, the reliability of the established simulation test platform was investigated. Based on this simulated test platform, in this paper the influence of the material structure and performance parameters (thickness, thermal conductivity, specific heat, density, emission rate and thermal reflectivity) of the heat radiation layer possessed by the three types of coating (thermal radiation protective coating, fireproof heat insulated coating and heat insulating coating) of three-layer coated flexible composites are discussed, thus providing the theoretical basis for the optimization and preparation of alternative outer materials for fire proximity suits. Based on the simulation data and measured results, the radiation protection performance of the three-layer structure is enhanced. Improving the average reflectivity of the heat rays for the thermal radiation protective coating, increasing the thickness of the heat insulating coating and reducing the thermal conductivity of the heat insulating coating are effective means of improving the radiation protection performance of the three-layer coated flexible composites.

scholarly journals Design of Thermal Insulation Materials with Different Geometries of Channels

Polymers ◽  
2021 ◽  
Vol 13 (13) ◽  
pp. 2217
Author(s):  
Daniela Șova ◽  
Mariana Domnica Stanciu ◽  
Sergiu Valeriu Georgescu
Keyword(s):  
Thermal Conductivity ◽  
Porous Structure ◽  
Base Material ◽  
Cost Effective ◽  
Heat Radiation ◽  
Average Temperature ◽  
Temperature Regimes ◽  
The Face ◽  
Inclined Channels ◽  
Air Channels

Investigating the large number of various materials now available, some materials scientists promoted a method of combining existing materials with geometric features. By studying natural materials, the performance of simple constituent materials is improved by manipulating their internal geometry; as such, any base material can be used by performing millimeter-scale air channels. The porous structure obtained utilizes the low thermal conductivity of the gas in the pores. At the same time, heat radiation and gas convection is hindered by the solid structure. The solution that was proposed in this research for obtaining a material with porous structure consisted in perforating extruded polystyrene (XPS) panels, as base material. Perforation was performed horizontally and at an angle of 45 degrees related to the face panel. The method is simple and cost-effective. Perforated and simple XPS panels were subjected to three different temperature regimes in order to measure the thermal conductivity. There was an increase in thermal conductivity with the increase in average temperature in all studied cases. The presence of air channels reduced the thermal conductivity of the perforated panels. The reduction was more significant at the panels with inclined channels. The differences between the thermal conductivity of simple XPS and perforated XPS panels are small, but the latter can be improved by increasing the number of channels and the air channels’ diameter. Additionally, the higher the thermal conductivity of the base material, the more significant is the presence of the channels, reducing the effective thermal conductivity. A base material with low emissivity may also reduce the thermal conductivity.

Effective thermal conductivity of open-pore metal foams as a function of the base material

2015 ◽  
Vol 57 (10) ◽  
pp. 825-836 ◽  
Author(s):  
Alexander Martin Matz ◽  
Bettina Stefanie Mocker ◽  
Norbert Jost ◽  
Peter Krug
Keyword(s):  
Thermal Conductivity ◽  
Effective Thermal Conductivity ◽  
Base Material ◽  
Metal Foams

scholarly journals The Equivalent Thermal Conductivity of the Micro/Nano Scaled Periodic Cubic Frame Silver and Its Thermal Radiation Mechanism Analysis

Energies ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 4158
Author(s):  
Haiyan Yu ◽  
Haochun Zhang ◽  
Heming Wang ◽  
Dong Zhang
Keyword(s):  
Thermal Conductivity ◽  
Thermal Radiation ◽  
Cell Size ◽  
Near Infrared ◽  
High Porosity ◽  
Mechanism Analysis ◽  
Infrared Band ◽  
Spectral Radiation ◽  
Radiation Mechanism ◽  
Equivalent Thermal Conductivity

Currently, there are few studies on the influence of microscale thermal radiation on the equivalent thermal conductivity of microscale porous metal. Therefore, this paper calculated the equivalent thermal conductivity of high-porosity periodic cubic silver frame structures with cell size from 100 nm to 100 µm by using the microscale radiation method. Then, the media radiation characteristics, absorptivity, reflectivity and transmissivity were discussed to explain the phenomenon of the radiative thermal conductivity changes. Furthermore, combined with spectral radiation properties at the different cross-sections and wavelength, the radiative transmission mechanism inside high-porosity periodic cubic frame silver structures was obtained. The results showed that the smaller the cell size, the greater radiative contribution in total equivalent thermal conductivity. Periodic cubic silver frames fluctuate more in the visible band and have better thermal radiation modulation properties in the near infrared band, which is formed by the Surface Plasmon Polariton and Magnetic Polaritons resonance jointly. This work provides design guidance for the application of this kind of periodic microporous metal in the field of thermal utilization and management.

Experimental Investigations on Aluminium Ultrasonic Welding Parameters

2014 ◽  
Vol 657 ◽  
pp. 306-310
Author(s):  
Lăcrămioara Apetrei ◽  
Vasile Rață ◽  
Ruxandra Rață ◽  
Elena Raluca Bulai
Keyword(s):  
Microstructural Analysis ◽  
Base Material ◽  
Welding Process ◽  
Ultrasonic Welding ◽  
Experimental Investigations ◽  
Welding Parameters ◽  
Material Structure ◽  
Welding Temperature ◽  
Wide Range ◽  
Made In

Research evolution timely tendencies, in the nonconventional technologies field, are: manufacture conditions optimization and complex equipments design. The increasing of ultrasonic machining use, in various technologies is due to the expanding need of a wide range materials and high quality manufacture standards in many activity fields. This paper present a experimental study made in order to analyze the welded zone material structure and welding quality. The effects of aluminium ultrasonic welding parameters such as relative energy, machining time, amplitude and working force were compared through traction tests values and microstructural analysis. Microhardness tests were, also, made in five different points, two in the base material and three in the welded zone, on each welded aluminium sample. The aluminum welding experiments were made at the National Research and Development Institute for Welding and Material Testing (ISIM) Timişoara. The ultrasonic welding temperature is lower than the aluminium melting temperature, that's so our experiments reveal that the aluminium ultrasonic welding process doesn't determine the appearance of moulding structure. In the joint we have only crystalline grains deformation, phase transformation and aluminium diffusion.

Thermal Conductivity Performance Modeling and Characterization of a Novel Anisotropic Conductive Adhesive Used in Lead-Free Electronics Packaging

2012 ◽  
Author(s):  
Matthew J. Combs ◽  
S. Manian Ramkumar ◽  
Satish Kandlikar
Keyword(s):  
Thermal Conductivity ◽  
Base Material ◽  
Bond Line ◽  
Thermal Interface Material ◽  
The Novel ◽  
Conductive Adhesives ◽  
Curing Conditions ◽  
Bond Line Thickness ◽  
Significant Research ◽  
American Society

The continued desire to utilize an alternative to lead-based solder materials for electrical interconnections has led to significant research interest in Anisotropic Conductive Adhesives (ACAs). The use of ACAs in electrical connections creates bonds using a combination of metal particles and epoxies to replace solder. The novel ACA discussed in this paper allows for bonds to be created through aligning columns of conductive particles along the Z-axis. These columns are formed by the application of a magnetic field, during the curing process. The benefit of this novel ACA is that it does not require precise printing of the adhesive on pads and also enables the mass curing without creating shorts in the circuitry. This paper will present the findings of the thermal conductivity performance tests using the novel ACA and its applicability as a thermal interface material and for assembling bottom termination components, power devices, etc. The columns that act as electrical conduction paths also contribute towards the thermal conductivity. The thermal conductivity of the novel ACA was measured utilizing a system that is similar to that in ASTM (American Society of Testing Materials) D5470 standard. The goal was to examine the influence of Bond Line Thickness (BLT), particle loading densities, particle diameters and adhesive matrix curing conditions on the electrical and thermal performance of the novel ACA. This paper will also present a numerical model to describe the thermal behavior of the novel ACA. The novel ACA’s applicability for PCB-level assembly has also been successfully demonstrated by RIT, including base material characterization, effect of process parameters, failures, and long-term reliability. Reliability testing included the investigation of the assembly performance in temperature and humidity aging, thermal aging, air-to-air thermal cycling, and drop testing.

scholarly journals Effective Thermal Conductivity of Open Cell Polyurethane Foam Based on the Fractal Theory

2013 ◽  
Vol 2013 ◽  
pp. 1-7 ◽  
Author(s):  
Kan Ankang ◽  
Han Houde
Keyword(s):  
Thermal Conductivity ◽  
Fractal Dimension ◽  
Effective Thermal Conductivity ◽  
Polyurethane Foam ◽  
Solid Phase ◽  
Fractal Theory ◽  
Heat Radiation ◽  
Total Thermal Conductivity ◽  
Equivalent Thermal Conductivity ◽  
Open Cell

Based on the fractal theory, the geometric structure inside an open cell polyurethane foam, which is widely used as adiabatic material, is illustrated. A simplified cell fractal model is created. In the model, the method of calculating the equivalent thermal conductivity of the porous foam is described and the fractal dimension is calculated. The mathematical formulas for the fractal equivalent thermal conductivity combined with gas and solid phase, for heat radiation equivalent thermal conductivity and for the total thermal conductivity, are deduced. However, the total effective heat flux is the summation of the heat conduction by the solid phase and the gas in pores, the radiation, and the convection between gas and solid phase. Fractal mathematical equation of effective thermal conductivity is derived with fractal dimension and vacancy porosity in the cell body. The calculated results have good agreement with the experimental data, and the difference is less than 5%. The main influencing factors are summarized. The research work is useful for the enhancement of adiabatic performance of foam materials and development of new materials.

scholarly journals Experimental investigation of rockwool insulation hygrothermal properties related to material structure

2015 ◽  
Vol 19 (3) ◽  
pp. 923-928 ◽  
Author(s):  
Maja Djurovic-Petrovic
Keyword(s):  
Thermal Conductivity ◽  
Experimental Investigation ◽  
Sorption Properties ◽  
Material Structure ◽  
Insulation Material ◽  
Wide Range ◽  
Two Samples

The hygrothermal properties related to rockwool insulation material structure with different additives are presented using rockwool insulation products obtained from row material of southern Serbia (Vranje region) in the wide range of reference temperatures (10?C to 70?C). The hygrothermal properties of basic sample (without additives) are compared to two samples with different additives for two sets of rockwool insulation samples namely: light-soft-panels (LSP) with density of 50 kg/m3, and middle-weight-panels (MWP) with density of 80 kg/m3. It is shown that there is significant (approximately 10%) improvement of thermal conductivity for additives based on zeolite. Also, correlation of thermal conductivity and sorption properties of selected samples are presented.

scholarly journals FIRE TESTING OF THE BUILDING FACADE INSULATED WITH FOAM POLYSTYRENE/PUTŲ POLISTIRENU APŠILTINTŲ FASADO FRAGMENTŲ GAISRINIAI BANDYMAI

1999 ◽  
Vol 5 (5) ◽  
pp. 340-346 ◽  
Author(s):  
Albertas Nyderis ◽  
Romualdas Mačiulaitis
Keyword(s):  
Thermal Radiation ◽  
Functional Relation ◽  
Heat Radiation ◽  
Bottom Line ◽  
Fire Hazards ◽  
Testing Conditions ◽  
Foam Polystyrene ◽  
Building Insulation ◽  
Building Facade ◽  
Insulation Systems

In the past decade, construction business applied various heat insulating materials comprising a spectrum of properties according to their combustibility. Particular attention was paid to insulation materials related to fire hazards. The normative fire safety documents started to be drawn up in this country at the time when the process of building insulation had not been initiated yet. Therefore, there still exists a great need for assessing the fire hazards of building insulation systems. With the use of the experience of other countries new testing equipment for insulating building facade with foam polystyrene has been recently established. The equipment is loaded with a 2.4×2.0 meter wall fragment and 800×700 mm plate of electrical thermal radiation flow, as well as a gas burner and a device for taking the temperature. The theoretical bottom-line of these testing methods lies in the heat exchange between two parallel walls, one of which is much hotter. The calculation of the thermal radiation flow is presented in formula 1 and the theoretical basis is indicated in formulae 2–10. Formula 11 indicates the rates of the flame heat radiation flows. Formula 12 shows special testing conditions. In the course of testing the insulation systems, the geometrical quantities of violation zones of foam polystyrene have been determined, they have exceeded the calculations of the flow radiation plate of active heat several times. A strong functional relation between the thickness of foam polystyrene and the rates of violation zones (r xy =0.694) and a weak functional relation between the thickness of plaster and the rates of violation zones (r xy = −0.580) have also been defined. Formulas 13 and 14 describe the relations between the surface areas of the destruction, the thickness of the foam polystyrene and the thickness of the plaster. By taking the temperatures in the vertical axis of the geometrical centre of the wall fragment, it was determined that in the course of testing the temperatures become dangerous in relation to the combustibles (about 250°C). The tests indicate that favourable and stable testing conditions established. It is expedient to continue the tests with other types of building facade materials.

scholarly journals The Kirchhoff Transformation for Convective-radiative Thermal Problemsin Fins

2021 ◽  
Vol 15 ◽  
pp. 12-21
Author(s):  
Jonatas Motta Quirino ◽  
Eduardo Dias Correa ◽  
Rodolfo do Lago Sobral
Keyword(s):  
Thermal Conductivity ◽  
Boundary Conditions ◽  
Thermal Radiation ◽  
Heat Dissipation ◽  
Variable Thermal Conductivity ◽  
Dirichlet Boundary Conditions ◽  
Heat Transfer Analysis ◽  
Temperature Function ◽  
Kirchhoff Transformation ◽  
Comparison Of The Results

- The present work describes the thermal profile of a single dissipation fin, where their surfaces reject heat to the environment. The problem happens in steady state, which is, all the analysis occurs after the thermal distribution reach heat balance considering that the fin dissipates heat by conduction, convection and thermal radiation. Neumann and Dirichlet boundary conditions are established, characterizing that heat dissipation occurs only on the fin faces, in addition to predicting that the ambient temperature is homogeneous. Heat transfer analysis is performed by computational simulations using appropriate numerical methods. The most of solutions in the literature consider some simplifications as constant thermal conductivity and linear boundary conditions, this work addresses this subject. The method applied is the Kirchhoff Transformation, that uses the thermal conductivity variation to define the temperatures values, once the thermal conductivity variate as a temperature function. For the real situation approximation, this work appropriated the silicon as the fin material to consider the temperature function at each point, which makes the equation that governs the non-linear problem. Finally, the comparison of the results obtained with typical results proves that the assumptions of variable thermal conductivity and heat dissipation by thermal radiation are crucial to obtain results that are closer to reality.

Sign in / Sign up

Export Citation Format

Share Document