scholarly journals Instability analysis of a filament-wound composite tube subjected to compression/bending

2019 ◽  
Vol 28 ◽  
pp. 096369351987741
Author(s):  
Gyula Szabó ◽  
Károly Váradi
Keyword(s):  
Failure Modes ◽  
Slenderness Ratio ◽  
Equivalent Stress ◽  
Bending Test ◽  
Test Machine ◽  
Fe Model ◽  
Rubber Tube ◽  
Nonlinear Buckling ◽  
Cross Sectional ◽  
Composite Tube

The aim of this study is to investigate the global buckling of a relatively long composite cord–rubber tube subjected to axial compression and its cross-sectional instability due to bending by a macromechanical nonlinear finite element (FE) model (nonlinear buckling analysis). Composite reinforcement layers are modelled as transversely isotropic ones, while elastomer liners are described by a hyperelastic material model that assumes incompressibility. Force–displacement, equivalent strain, equivalent stress results along with oblateness and curvature results for the complete process have been presented. It is justified that bending leads to ovalization of the cross section and results in a loss of the load-carrying capacity of the tube. Strain states in reinforcement layers have been presented, which imply that the probable failure modes of the reinforcement layers are both delamination and yarn-matrix debonding. There is a significant increase in strains due to cross-sectional instability, which proves that the effect of cross-sectional instability on material behaviour of the tube is crucial. A parametric analysis has been performed to investigate the effect of the member slenderness ratio on cross-sectional instability of the composite tube. It shows that Brazier force is inversely proportional to the slenderness ratio. It further shows that higher oblateness parameters occur in case of a lower slenderness ratio and that cross-sectional instability takes place at a lower dimensionless displacement in case of a lower slenderness ratio. FE results have been validated by a compression/bending test experiment conducted on a tensile test machine.

scholarly journals Analysis of Fire Resistance of Square-Cased Square Steel Tube Reinforced Concrete (ST-RC) Columns

Materials ◽  
2021 ◽  
Vol 14 (19) ◽  
pp. 5541
Author(s):  
Gaoxiong Wang ◽  
Yanhong Bao ◽  
Li Yang ◽  
Yang Yu
Keyword(s):  
Reinforced Concrete ◽  
Fire Resistance ◽  
Slenderness Ratio ◽  
Concrete Strength ◽  
Load Ratio ◽  
Internal Force ◽  
Steel Tube ◽  
Fe Model ◽  
Cross Sectional ◽  
Rc Columns

Based on the finite element (FE) analysis software Abaqus, an FE model of square-cased square steel tube reinforced concrete (ST-RC) columns under the hybridized action of high-temperature and load is established. The accuracy of the FE model is verified using experimental data from existing studies. This model is used to analyze the temperature change, internal force distribution, and failure characteristics of the square-cased square ST-RC columns under the action of fire, as well as the factors affecting the fire resistance limit of the column. The results of FE analysis show that under the action of fire, the maximum internal temperature of the square-cased square ST-RC columns occurs in the corner of the section. Moreover, the stress and strain reach their maximum values at the concrete corner outside the tube. During the heating process, an internal force redistribution occurs in the square-cased square ST-RC column. At the same time, the proportion of the axial force and the bending moment of the reinforced concrete outside the pipe decreases gradually, while the proportion of the internal force of the core concrete-filled steel tube (CFST) increases gradually. In essence, it is a process of load transfer from the high-temperature to the low-temperature zone. In addition, the section size, load ratio, slenderness ratio, cross-sectional core area ratio, steel content, and external concrete strength are the main parameters affecting the fire resistance limit of the square-cased square ST-RC columns. Among them, the cross-sectional core area ratio, section size, steel ratio, and external concrete strength are positively correlated with the fire resistance limit of the composite column. On the contrary, with the increase in the load ratio and the slenderness ratio, the fire resistance limit of the square-cased square ST-RC columns decreases. On this basis, a simplified formula to calculate the fire resistance limit of square-cased square ST-RC columns is proposed. The research results can be used as a theoretical reference for the fire protection design of this kind of structure in practical engineering.

Determination of the metal toughness components in impact-bending test

2018 ◽  
Vol 84 (12) ◽  
pp. 68-72
Author(s):  
A. B. Maksimov ◽  
I. P. Shevchenko ◽  
I. S. Erokhina
Keyword(s):  
Crack Growth ◽  
Specific Energy ◽  
Crack Formation ◽  
Crack Nucleation ◽  
Scale Effects ◽  
Linear Equations ◽  
Bending Test ◽  
Cross Sectional ◽  
Two Samples ◽  
Sample Width

A method for separating the work of impact into two parts - the work of the crack nucleation and that of crack growth - which consists in testing two samples with the same stress concentrators and different cross-sectional dimensions at the notch site is developed. It is assumed that the work of crack nucleation is proportional to the width of the sample face on which the crack originates and the specific energy of crack formation, whereas the work of the crack growth is proportional to the length of crack development and the specific crack growth energy. In case of the sample fracture upon testing, the crack growth length is assumed equal to the sample width. Data on the work of fracture of two samples and their geometrical dimensions at the site of the notch are used to form a system of two linear equations in two unknowns, i.e., the specific energy of crack formation and specific energy of crack growth. The determined specific energy values are then used to calculate the work of crack nucleation and work of crack growth. The use of the analytical method improves the accuracy compared to graphical - extrapolative procedures. The novelty of the method consists in using one and the same form of the notch in test samples, thus providing the same conditions of the stress-strain state for crack nucleation and growth. Moreover, specimens with different cross-section dimensions are used to eliminate the scale effects. Since the specific energy of the crack nu-cleation and specific energy of the crack growth are independent of the scale factor, they are determined only by the properties of the metal. Introduction the specific energy of crack formation and growth makes possible to assign a specific physical meaning to the fracture energy.

scholarly journals Numerical Modeling and Safety Design for Lithium-Ion Vehicle Battery Modules Subject to Crush Loading

Energies ◽  
2020 ◽  
Vol 14 (1) ◽  
pp. 118
Author(s):  
Feng Zhu ◽  
Runzhou Zhou ◽  
David J. Sypeck
Keyword(s):  
Failure Modes ◽  
Computational Study ◽  
Short Circuit ◽  
Computational Cost ◽  
Lithium Ion ◽  
Simplified Model ◽  
Homogeneous Material ◽  
Fe Model ◽  
Safety Design ◽  
Battery Module

In this work, a computational study was carried out to simulate crushing tests on lithium-ion vehicle battery modules. The tests were performed on commercial battery modules subject to wedge cutting at low speeds. Based on loading and boundary conditions in the tests, finite element (FE) models were developed using explicit FEA code LS-DYNA. The model predictions demonstrated a good agreement in terms of structural failure modes and force–displacement responses at both cell and module levels. The model was extended to study additional loading conditions such as indentation by a cylinder and a rectangular block. The effect of other module components such as the cover and cooling plates was analyzed, and the results have the potential for improving battery module safety design. Based on the detailed FE model, to reduce its computational cost, a simplified model was developed by representing the battery module with a homogeneous material law. Then, all three scenarios were simulated, and the results show that this simplified model can reasonably predict the short circuit initiation of the battery module.

scholarly journals Design and analysis of concrete-filled tubular flange girders under combined loading

2021 ◽  
pp. 136943322110015
Author(s):  
Rana Al-Dujele ◽  
Katherine Ann Cashell
Keyword(s):  
Finite Element ◽  
Axial Force ◽  
Failure Modes ◽  
Numerical Study ◽  
Combined Loading ◽  
Torsional Stiffness ◽  
Fe Model ◽  
Combined Effects ◽  
Element Analysis ◽  
Hollow Section

This paper is concerned with the behaviour of concrete-filled tubular flange girders (CFTFGs) under the combination of bending and tensile axial force. CFTFG is a relatively new structural solution comprising a steel beam in which the compression flange plate is replaced with a concrete-filled hollow section to create an efficient and effective load-carrying solution. These members have very high torsional stiffness and lateral torsional buckling strength in comparison with conventional steel I-girders of similar depth, width and steel weight and are there-fore capable of carrying very heavy loads over long spans. Current design codes do not explicitly include guidance for the design of these members, which are asymmetric in nature under the combined effects of tension and bending. The current paper presents a numerical study into the behaviour of CFTFGs under the combined effects of positive bending and axial tension. The study includes different loading combinations and the associated failure modes are identified and discussed. To facilitate this study, a finite element (FE) model is developed using the ABAQUS software which is capable of capturing both the geometric and material nonlinearities of the behaviour. Based on the results of finite element analysis, the moment–axial force interaction relationship is presented and a simplified equation is proposed for the design of CFTFGs under combined bending and tensile axial force.

Fire and Post-Fire Performance of Space Grid Structures

2012 ◽  
Vol 238 ◽  
pp. 621-624 ◽  
Author(s):  
Guang Yong Wang ◽  
Xing Qiang Wang ◽  
Guang Wei Liu
Keyword(s):  
Finite Element ◽  
Failure Modes ◽  
Fe Model ◽  
Fire Damage ◽  
Fire Performance ◽  
Membrane Action ◽  
Load Bearing Capacity ◽  
Space Grid ◽  
Deformation Stress ◽  
In Fire

A fire performance finite element (FE) model of space grid structures in fire and after fire is proposed, and deformation, stress redistribution, failure modes of grid structures are also studied. The result shows that tensile membrane action arises when the grid is loaded after fire, and the load bearing capacity after fire is reduced by fire damage.

Comparison of the Cross Sectional Area, the Loss in Volume and the Mechanical Properties of LAE442 and MgCa0.8 as Resorbable Magnesium Alloy Implants after 12 Months Implantation Duration

2010 ◽  
Vol 638-642 ◽  
pp. 675-680 ◽  
Author(s):  
Martina Thomann ◽  
Nina von der Höh ◽  
Dirk Bormann ◽  
Dina Rittershaus ◽  
C. Krause ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Cross Sections ◽  
Degradation Process ◽  
Cross Sectional Area ◽  
Bending Test ◽  
Sectional Area ◽  
Cross Sectional ◽  
Initial Strength ◽  
Three Point Bending ◽  
The Cross

Current research focuses on magnesium based alloys in the course of searching a resorbable osteosynthetic material which provides sufficient mechanical properties besides a good biocompatibility. Previous studies reported on a favorable biocompatibility of the alloys LAE442 and MgCa0.8. The present study compared the degradation process of cylindrical LAE442 and MgCa0.8 implants after 12 months implantation duration. Therefore, 10 extruded implants (2.5 x 25 mm, cross sectional area 4.9 mm²) of both alloys were implanted into the medullary cavity of both tibiae of rabbits for 12 months. After euthanization, the right bone-implant-compound was scanned in a µ-computed tomograph (µCT80, ScancoMedical) and nine uniformly distributed cross-sections of each implant were used to determine the residual implants´ cross sectional area (Software AxioVisionRelease 4.5, Zeiss). Left implants were taken out of the bone carefully. After weighing, a three-point bending test was carried out. LAE442 implants degraded obviously slower and more homogeneously than MgCa0.8. The mean residual cross sectional area of LAE442 implants was 4.7 ± 0.07 mm². MgCa0.8 showed an area of only 2.18 ± 1.03 mm². In contrast, the loss in volume of LAE442 pins was more obvious. They lost 64 % of their initial weight. The volume of MgCa0.8 reduced clearly to 54.4 % which corresponds to the cross sectional area results. Three point bending tests revealed that LAE442 showed a loss in strength of 71.2 % while MgCa0.8 lost 85.6 % of its initial strength. All results indicated that LAE442 implants degraded slowly, probably due to the formation of a very obvious degradation layer. Degradation of MgCa0.8 implants was far advanced.

scholarly journals Edgewise Compressive Behavior of Composite Structural Insulated Panels with Magnesium Oxide Board Facings

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3030
Author(s):  
Łukasz Smakosz ◽  
Ireneusz Kreja ◽  
Zbigniew Pozorski
Keyword(s):  
Magnesium Oxide ◽  
Sandwich Panel ◽  
Failure Modes ◽  
Small Scale ◽  
Fe Model ◽  
Compressive Behavior ◽  
Axial Loads ◽  
Reliable Prediction ◽  
Structural Insulated Panels ◽  
Prediction Capability

Edgewise compression response of a composite structural insulated panel (CSIP) with magnesium oxide board facings was investigated. The discussed CSIP is a novel multifunctional sandwich panel introduced to the housing industry as a part of the wall, floor, and roof assemblies. The study aims to propose a computational tool for reliable prediction of failure modes of CSIPs subjected to concentric and eccentric axial loads. An advanced numerical model was proposed that includes geometrical and material nonlinearity as well as incorporates the material bimodularity effect to achieve accurate and versatile failure mode prediction capability. Laboratory tests on small-scale CSIP samples of three different slenderness ratios and full-scale panels loaded with three different eccentricity values were carried out, and the test data were compared with numerical results for validation. The finite element (FE) model successfully captured CSIP’s inelastic response in uniaxial compression and when flexural action was introduced by eccentric loads or buckling and predicted all failure modes correctly. The comprehensive validation showed that the proposed approach could be considered a robust and versatile aid in CSIP design.

Sensor Fusion and On-Line Monitoring of Friction Stir Blind Riveting for Lightweight Materials Manufacturing

2021 ◽  
pp. 1-36
Author(s):  
Zhe Gao ◽  
Haris Khan ◽  
Jingjing Li ◽  
Weihong Guo
Keyword(s):  
Sensor Fusion ◽  
Failure Modes ◽  
Processing Parameters ◽  
Data Driven ◽  
Structure Property ◽  
Cross Sectional ◽  
Friction Stir ◽  
In Situ Data ◽  
Lap Shear

Abstract This research focused on developing a hybrid quality monitoring model through combining the data driven and key engineering parameters to predict the friction stir blind riveting (FSBR) joint quality. The hybrid model was formulated through utilizing the in-situ processing and joint property data. The in-situ data involved sensor fusion (force and torque signals) and key processing parameters (spindle speed, feed rate and stacking sequence) for data-driven modeling. The quality of the FSBR joints was defined by the tensile strength. Further, the joint cross-sectional analysis and failure modes in lap-shear tests were employed to confirm the efficacy of the proposed model and development of the process-structure-property relationship.

scholarly journals Large deflection and post-buckling of thin-walled structures by finite elements with node-dependent kinematics

2020 ◽  
Author(s):  
E. Carrera ◽  
◽  
A. Pagani ◽  
R. Augello
Keyword(s):  
Finite Elements ◽  
Large Deflection ◽  
Nonlinear Problems ◽  
Structural Domain ◽  
Fe Model ◽  
Efficient Manner ◽  
Cross Sectional ◽  
Thin Walled Structures ◽  
Post Buckling ◽  
Thin Walled

AbstractIn the framework of finite elements (FEs) applications, this paper proposes the use of the node-dependent kinematics (NDK) concept to the large deflection and post-buckling analysis of thin-walled metallic one-dimensional (1D) structures. Thin-walled structures could easily exhibit local phenomena which would require refinement of the kinematics in parts of them. This fact is particularly true whenever these thin structures undergo large deflection and post-buckling. FEs with kinematics uniform in each node could prove inappropriate or computationally expensive to solve these locally dependent deformations. The concept of NDK allows kinematics to be independent in each element node; therefore, the theory of structures changes continuously over the structural domain. NDK has been successfully applied to solve linear problems by the authors in previous works. It is herein extended to analyze in a computationally efficient manner nonlinear problems of beam-like structures. The unified 1D FE model in the framework of the Carrera Unified Formulation (CUF) is referred to. CUF allows introducing, at the node level, any theory/kinematics for the evaluation of the cross-sectional deformations of the thin-walled beam. A total Lagrangian formulation along with full Green–Lagrange strains and 2nd Piola Kirchhoff stresses are used. The resulting geometrical nonlinear equations are solved with the Newton–Raphson linearization and the arc-length type constraint. Thin-walled metallic structures are analyzed, with symmetric and asymmetric C-sections, subjected to transverse and compression loadings. Results show how FE models with NDK behave as well as their convenience with respect to the classical FE analysis with the same kinematics for the whole nodes. In particular, zones which undergo remarkable deformations demand high-order theories of structures, whereas a lower-order theory can be employed if no local phenomena occur: this is easily accomplished by NDK analysis. Remarkable advantages are shown in the analysis of thin-walled structures with transverse stiffeners.

scholarly journals Effect of Bolt-Hole Clearance on Bolted Connection Behavior for Pultruded Fiber-Reinforced Polymer Structural Plastic Members

2017 ◽  
Vol 2017 ◽  
pp. 1-12 ◽  
Author(s):  
Sang-Pyuk Woo ◽  
Sun-Hee Kim ◽  
Soon-Jong Yoon ◽  
Wonchang Choi
Keyword(s):  
Failure Modes ◽  
Fiber Reinforced Polymer ◽  
Structural Members ◽  
Fiber Reinforced ◽  
Cross Sectional ◽  
Bolted Connection ◽  
Reinforced Polymer ◽  
Connection System ◽  
Structural Plastic ◽  
Bolt Connection

Bolt-hole clearance affects the failure mode on the bolted connection system of pultruded fiber-reinforced polymer plastic (PFRP) members. The various geometric parameters, such as the shape and cross-sectional area of the structural members, commonly reported in many references were used to validate the bolt-hole clearance. This study investigates the effects of the bolt-hole clearance in single-bolt connections of PFRP structural members. Single-bolt connection tests were planned using different bolt-hole clearances (e.g., tight-fit and clearances of 0.5 mm to 3.0 mm with 0.5 mm intervals) and uniaxial tension is applied on the test specimens. Most of the specimens failed in two sequential failure modes: bearing failure occurred and the shear-out failure followed. Test results on the bolt-hole clearances are compared with results in the previous research.

Sign in / Sign up

Export Citation Format

Share Document