Research on coordination design method of main bearing assembly structure based on the maximum radial deformation of bearing bush

2021 ◽  
pp. 146808742110409
Author(s):  
Xin Zhao ◽  
Tiexiong Su ◽  
Xiaoyong Liu ◽  
Yunpeng Feng
Keyword(s):  
High Speed ◽  
Design Method ◽  
Design Parameters ◽  
Radial Deformation ◽  
Main Bearing ◽  
Tightening Force ◽  
Assembly Structure ◽  
Bearing Assembly ◽  
Numerical Calculation Method ◽  
Coordination Design

Aiming at the difficulty of control and evaluation of main bearing deformation in the coordination design of the main bearing assembly structure for a high-speed diesel engine, taking MRD (the MRD means the maximum radial deformation of the bearing bush) of the bearing bush as an index to evaluate the out-of-round deformation of the bearing bush was proposed in this paper. The numerical calculation method of the MRD was given and the correctness of the method was experimentally verified. And the influence rules of different design parameters on the MRD were analyzed. On this basis, the coordination multi-objective optimization research of the main bearing assembly structure was carried out, and the optimization results were analyzed based on the influence rules of different design parameters on the reliability indexes. The results show that, when the pre-tightening force of the vertical bolt and the bearing bush interference are 240 kN and 0.17 mm respectively, the MRD reaches the minimum value. If the two values continue to increase, redundant loads can be generated, leading to the increase of the MRD. After optimization, the engine block strength coordination and bearing cap strength coordination had increased by 2.47% and 10.48%, respectively, and the deformation coordination and contact coordination had increased by 46.15% and 14.84%, respectively.

Development of High-Speed Response Electromagnetic Linear Actuator Using for Pneumatic Control Valve

2014 ◽  
Vol 532 ◽  
pp. 41-45 ◽  
Author(s):  
Myung Jin Chung
Keyword(s):  
Optimal Design ◽  
Dynamic Characteristics ◽  
High Speed ◽  
Design Method ◽  
Control Valve ◽  
Design Parameters ◽  
Linear Actuator ◽  
Analytic Model ◽  
Electromagnetic Linear Actuator ◽  
Quadratic Programming Method

Analytic model of electromagnetic linear actuator in the function of electric and geometric parameters is proposed and the effects of the design parameters on the dynamic characteristics are analyzed. To improve the dynamic characteristics, optimal design is conducted by applying sequential quadratic programming method to the analytic model. This optimal design method aims to minimize the response time and maximize force efficiency. By this procedure, electromagnetic linear actuator having high-speed characteristics is developed.

scholarly journals Design Method for Contra-Rotating Propellers for High-Speed Crafts: Revising the Original Lerbs Theory in a Modern Perspective

2012 ◽  
Vol 2012 ◽  
pp. 1-18 ◽  
Author(s):  
Stefano Brizzolara ◽  
Davide Grassi ◽  
Emilio P. Tincani
Keyword(s):  
High Speed ◽  
Design Theory ◽  
Design Method ◽  
Design Parameters ◽  
Strength Criteria ◽  
New Methods ◽  
Modified Method ◽  
Circulation Distribution ◽  
Pod Propulsor ◽  
Modern Perspective

The main theoretical and numerical aspects of a design method for optimum contrar-rotating (CR) propellers for fast marine crafts are presented. We propose a reformulated version of a well-known design theory for contra-rotating propellers, by taking advantage of a new fully numerical algorithm for the calculation of the mutually induced velocities and introducing new features such as numerical lifting surface corrections, use of an integrated modern cavitation/strength criteria, a modified method to consider different numbers of blades among the two propellers, and to allow for an unloading function in the search for the optimal circulation distribution. The paper first introduces the main theoretical principles of the new methods and then discusses the influence of the main design parameters on an emblematic example of application in the case of counter rotating propellers for a pod propulsor designed for fast planing crafts (35 knots and above).

scholarly journals Optimal Design of High-Power Medium-Frequency Transformer Using Hollow Conductors with Consideration of Multi-Objective Parameters

Energies ◽  
2020 ◽  
Vol 13 (14) ◽  
pp. 3654
Author(s):  
Yunxiang Guo ◽  
Cheng Lu ◽  
Liang Hua ◽  
Xinsong Zhang
Keyword(s):  
Optimal Design ◽  
High Power ◽  
High Speed ◽  
Comprehensive Evaluation ◽  
Design Method ◽  
System Structure ◽  
Design Parameters ◽  
Medium Frequency ◽  
Evaluation Standard ◽  
Leakage Inductance

A power electronic transformer (PET) is applied to the high-speed train for lightweight demand. A 300 kW/5 kHz high-power medium-frequency transformer (HPMFT) using hollow conductors in a power unit of the PET is optimally designed in this paper. The target of the design is to balance the loss, leakage inductance, and weight of the HPMFT. For this purpose, the design parameters of the HPMFT are firstly confirmed according to the system structure and parameters of the PET. Secondly, the design process of HPMFT is developed. Finally, the results of 48 design schemes of core-type and shell-type structures are compared by the comprehensive evaluation standard, which equilibrates the three above objective parameters of the HPMFT. According to the optimal scheme, a prototype is manufactured, whose test results verify the correctness of the optimal design method.

scholarly journals A Systematic Optimization Design Method for Complex Mechatronic Products Design and Development

2018 ◽  
Vol 2018 ◽  
pp. 1-14 ◽  
Author(s):  
Jie Jiang ◽  
Guofu Ding ◽  
Jian Zhang ◽  
Yisheng Zou ◽  
Shengfeng Qin
Keyword(s):  
High Speed ◽  
Optimization Design ◽  
Design Space ◽  
Design Method ◽  
Evaluation Criteria ◽  
Research Problem ◽  
Optimization Techniques ◽  
Design Parameters ◽  
Space Reduction ◽  
Systematic Optimization

Designing a complex mechatronic product involves multiple design variables, objectives, constraints, and evaluation criteria as well as their nonlinearly coupled relationships. The design space can be very big consisting of many functional design parameters, structural design parameters, and behavioral design (or running performances) parameters. Given a big design space and inexplicit relations among them, how to design a product optimally in an optimization design process is a challenging research problem. In this paper, we propose a systematic optimization design method based on design space reduction and surrogate modelling techniques. This method firstly identifies key design parameters from a very big design space to reduce the design space, secondly uses the identified key design parameters to establish a system surrogate model based on data-driven modelling principles for optimization design, and thirdly utilizes the multiobjective optimization techniques to achieve an optimal design of a product in the reduced design space. This method has been tested with a high-speed train design. With comparison to others, the research results show that this method is practical and useful for optimally designing complex mechatronic products.

Aerodynamic and aeroacoustic performance investigations on modified H-rotor Darrieus wind turbine

2021 ◽  
pp. 0309524X2110039
Author(s):  
Amgad Dessoky ◽  
Thorsten Lutz ◽  
Ewald Krämer
Keyword(s):  
Wind Turbine ◽  
High Speed ◽  
Cfd Simulation ◽  
Vertical Axis ◽  
3D Models ◽  
Power Coefficient ◽  
Design Parameters ◽  
Second Phase ◽  
Vertical Axis Wind Turbine ◽  
Guide Vanes

The present paper investigates the aerodynamic and aeroacoustic characteristics of the H-rotor Darrieus vertical axis wind turbine (VAWT) combined with very promising energy conversion and steering technology; a fixed guide-vanes. The main scope of the current work is to enhance the aerodynamic performance and assess the noise production accomplished with such enhancement. The studies are carried out in two phases; the first phase is a parametric 2D CFD simulation employing the unsteady Reynolds-averaged Navier-Stokes (URANS) approach to optimize the design parameters of the guide-vanes. The second phase is a 3D CFD simulation of the full turbine using a higher-order numerical scheme and a hybrid RANS/LES (DDES) method. The guide-vanes show a superior power augmentation, about 42% increase in the power coefficient at λ = 2.75, with a slightly noisy operation and completely change the signal directivity. A remarkable difference in power coefficient is observed between 2D and 3D models at the high-speed ratios stems from the 3D effect. As a result, a 3D simulation of the capped Darrieus turbine is carried out, and then a noise assessment of such configuration is assessed. The results show a 20% increase in power coefficient by using the cap, without significant change in the noise signal.

scholarly journals A modular design method based on TRIZ and AD and its application to cutter changing robot

2021 ◽  
Vol 13 (7) ◽  
pp. 168781402110343
Author(s):  
Mei Yang ◽  
Yimin Xia ◽  
Lianhui Jia ◽  
Dujuan Wang ◽  
Zhiyong Ji
Keyword(s):  
Modular Design ◽  
Design Method ◽  
Idea Generation ◽  
Design Parameters ◽  
Problem Analysis ◽  
Concept Design ◽  
Functional Requirements ◽  
Shield Tunneling ◽  
Structural Hierarchy ◽  
And Performance

Modular design, Axiomatic design (AD) and Theory of inventive problem solving (TRIZ) have been increasingly popularized in concept design of modern mechanical product. Each method has their own advantages and drawbacks. The benefit of modular design is reducing the product design period, and AD has the capability of problem analysis, while TRIZ’s expertise is innovative idea generation. According to the complementarity of these three approaches, an innovative and systematic methodology is proposed to design big complex mechanical system. Firstly, the module partition is executed based on scenario decomposition. Then, the behavior attributes of modules are listed to find the design contradiction, including motion form, spatial constraints, and performance requirements. TRIZ tools are employed to deal with the contradictions between behavior attributes. The decomposition and mapping of functional requirements and design parameters are carried out to construct the structural hierarchy of each module. Then, modules are integrated considering the connections between each other. Finally, the operation steps in application scenario are designed in temporal and spatial dimensions. Design of cutter changing robot for shield tunneling machine is taken as an example to validate the feasibility and effectiveness of the proposed method.

The Engagement of Hybrid Ultra High Space Division Multiplexing with Maximum Time Division Multiplexing Techniques for High-Speed Single-Mode Fiber Cable Systems

2019 ◽  
Vol 0 (0) ◽  
Author(s):  
I. S. Amiri ◽  
P. G. Kuppusamy ◽  
Ahmed Nabih Zaki Rashed ◽  
P. Jayarajan ◽  
M. R. Thiyagupriyadharsan ◽  
...  
Keyword(s):  
Communication Systems ◽  
High Speed ◽  
Single Mode ◽  
Single Mode Fiber ◽  
Design Parameters ◽  
Control Parameters ◽  
Data Rates ◽  
Fiber Optic Communication ◽  
High Space ◽  
Optic Communication

AbstractHigh-speed single-mode fiber-optic communication systems have been presented based on various hybrid multiplexing schemes. Refractive index step and silica-doped germanium percentage parameters are also preserved during their technological boundaries of attention. It is noticed that the connect design parameters suffer more nonlinearity with the number of connects. Two different propagation techniques have been used to investigate the transmitted data rates as a criterion to enhance system performance. The first technique is soliton propagation, where the control parameters lead to equilibrium between the pulse spreading due to dispersion and the pulse shrinking because of nonlinearity. The second technique is the MTDM technique where the parameters are adjusted to lead to minimum dispersion. Two cases are investigated: no dispersion cancellation and dispersion cancellation. The investigations are conducted over an enormous range of the set of control parameters. Thermal effects are considered through three basic quantities, namely the transmission data rates, the dispersion characteristics, and the spectral losses.

Parameter study and optimization design of a hat oblique tunnel portal

2021 ◽  
pp. 095440972110140
Author(s):  
Zijian Guo ◽  
Tanghong Liu ◽  
Wenhui Li ◽  
Yutao Xia
Keyword(s):  
High Speed ◽  
Optimization Design ◽  
Pareto Front ◽  
Optimization Problem ◽  
Optimization Method ◽  
Design Parameters ◽  
Parameter Study ◽  
Buffer Structure ◽  
Tunnel Entrance ◽  
The Ideal

The present work focuses on the aerodynamic problems resulting from a high-speed train (HST) passing through a tunnel. Numerical simulations were employed to obtain the numerical results, and they were verified by a moving-model test. Two responses, [Formula: see text] (coefficient of the peak-to-peak pressure of a single fluctuation) and[Formula: see text] (pressure value of micro-pressure wave), were studied with regard to the three building parameters of the portal-hat buffer structure of the tunnel entrance and exit. The MOPSO (multi-objective particle swarm optimization) method was employed to solve the optimization problem in order to find the minimum [Formula: see text] and[Formula: see text]. Results showed that the effects of the three design parameters on [Formula: see text] were not monotonous, and the influences of[Formula: see text] (the oblique angle of the portal) and [Formula: see text] (the height of the hat structure) were more significant than that of[Formula: see text] (the angle between the vertical line of the portal and the hat). Monotonically decreasing responses were found in [Formula: see text] for [Formula: see text] and[Formula: see text]. The Pareto front of [Formula: see text] and[Formula: see text]was obtained. The ideal single-objective optimums for each response located at the ends of the Pareto front had values of 1.0560 for [Formula: see text] and 101.8 Pa for[Formula: see text].

scholarly journals Reliability Evaluation of Fan-Out Type 3D Packaging-On-Packaging

Micromachines ◽  
2021 ◽  
Vol 12 (3) ◽  
pp. 295
Author(s):  
Pao-Hsiung Wang ◽  
Yu-Wei Huang ◽  
Kuo-Ning Chiang
Keyword(s):  
Finite Element ◽  
Thermal Cycling ◽  
Glass Substrate ◽  
High Speed ◽  
Coefficient Of Thermal Expansion ◽  
Three Dimensional ◽  
Design Parameters ◽  
Time To Failure ◽  
Wafer Level ◽  
Fine Pitch

The development of fan-out packaging technology for fine-pitch and high-pin-count applications is a hot topic in semiconductor research. To reduce the package footprint and improve system performance, many applications have adopted packaging-on-packaging (PoP) architecture. Given its inherent characteristics, glass is a good material for high-speed transmission applications. Therefore, this study proposes a fan-out wafer-level packaging (FO-WLP) with glass substrate-type PoP. The reliability life of the proposed FO-WLP was evaluated under thermal cycling conditions through finite element simulations and empirical calculations. Considering the simulation processing time and consistency with the experimentally obtained mean time to failure (MTTF) of the packaging, both two- and three-dimensional finite element models were developed with appropriate mechanical theories, and were verified to have similar MTTFs. Next, the FO-WLP structure was optimized by simulating various design parameters. The coefficient of thermal expansion of the glass substrate exerted the strongest effect on the reliability life under thermal cycling loading. In addition, the upper and lower pad thicknesses and the buffer layer thickness significantly affected the reliability life of both the FO-WLP and the FO-WLP-type PoP.

Sign in / Sign up

Export Citation Format

Share Document