Characterization and dielectric properties of sodium fluoride doped talc

Clay Minerals ◽  
2014 ◽  
Vol 49 (4) ◽  
pp. 551-558
Author(s):  
S. Gümüştas ◽  
K. Köseoğlu ◽  
E. E. Yalçinkaya ◽  
M. Balcan
Keyword(s):  
Dielectric Constant ◽  
Dielectric Properties ◽  
Dielectric Loss ◽  
Firing Temperature ◽  
Room Temperature ◽  
Dielectric Measurements ◽  
Frequency Range ◽  
Detailed Characterization ◽  
Circuit Element

AbstractThe purpose of this paper is to determine the effect of NaF and firing temperature on the dielectric properties (dielectric constant and dielectric loss) of talc, which is used in the electrical and electronic industries as a circuit element. A detailed characterization of the samples was made by XRD, FTIR, SEM and TG-DTG methods. Dielectric measurements were performed in the frequency range from 1 MHz to 80 MHz at room temperature. The dielectric constant value increased with an increase in firing temperature due to the removal of polarizable compounds from the talc structure. The higher dielectric constant values were obtained by addition of NaF. The dielectric loss of NaF doped talc decreased with the increase of firing temperature and increased with the increase of the amount of NaF.

Preparation and Characterization of CaCu3Ti4O12 Ceramics by Cold Isostatic Press Forming

2008 ◽  
Vol 368-372 ◽  
pp. 123-125
Author(s):  
Jie Li ◽  
Hao Xue ◽  
Zhao Xian Xiong
Keyword(s):  
Dielectric Constant ◽  
Dielectric Properties ◽  
Room Temperature ◽  
Frequency Range ◽  
Cold Isostatic Press ◽  
Temperature Range ◽  
Press Forming ◽  
Conventional Sintering ◽  
Sintering Method

CaCu3Ti4O12 (CCTO) ceramics were prepared by cold isostatic press (CIP) forming combined with the conventional sintering method. The effects of calcining temperature on properties of CCTO ceramics were investigated. The dielectric properties as the function of temperature at typical frequencies were measured in the temperature range from 243 to 363 K. In addition, the dielectric properties and complex impedances at room temperature were analyzed in a frequency range from 20 Hz to 106 Hz. The results showed that CCTO ceramics with dielectric constant higher than 104 were obtained. Compared with the dry press forming, CCTO ceramics prepared by CIP had more homogeneous grains, less porosity and better dielectric properties.

Effect of moisture content on dielectric properties of banana leaves and peels in frequency range of 1–20 GHz

Frequenz ◽  
2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Soumya Sundar Pattanayak ◽  
Soumen Biswas
Keyword(s):  
Dielectric Constant ◽  
Dielectric Properties ◽  
Dielectric Loss ◽  
Moisture Content ◽  
Measurement Data ◽  
Banana Peel ◽  
Frequency Range ◽  
Proposed Model ◽  
Banana Leaves ◽  
Banana Leaf

Abstract The quality of agricultural products can be remotely sensed and enhanced by determining the dielectric properties. This paper studies the dielectric properties of banana leaf and banana peel over the frequency range 1–20 GHz using the open-ended coaxial probe (OCP) method. A new curve fitting model is proposed to characterize the dielectric properties of banana leaf and banana peel. The different moisture content (MC) levels are considered for both banana leaf and banana peel samples and, their dielectric properties are characterized. Further, the banana leaf and banana peel’s measurement data are compared with the data obtained using the proposed model. In addition, Root Mean Square Error (RMSE) and R-squared (R 2) are calculated to validate the performance of the proposed model. In case of banana leaf at 68.26% MC, the dielectric constant achieves the value of R 2 and RMSE of 0.98 and 0.0648, respectively. Similarly, dielectric loss achieves the value of R 2 and RMSE of 0.88 and 0.0795, respectively. Further, for banana peel at 80.89% MC, the dielectric constant achieves the value of R 2 and RMSE of 0.99 and 0.2989, respectively. Similarly, dielectric loss achieves the value of R 2 and RMSE of 0.96 and 0.6132, respectively.

Effect of Sintering Temperature on Dielectric Properties of CaCu3Ti4O12 Ceramics Prepared by Mechanochemical Process

2014 ◽  
Vol 974 ◽  
pp. 157-161
Author(s):  
Masturah Mohamed ◽  
Mahesh Talari ◽  
Mohd Salleh Mohd Deni ◽  
Azlan Zakaria
Keyword(s):  
Dielectric Constant ◽  
Dielectric Properties ◽  
Sintering Temperature ◽  
Processing Conditions ◽  
Dielectric Measurements ◽  
Frequency Range ◽  
Grain Sizes ◽  
Barrier Capacitance ◽  
Different Temperatures ◽  
Increasing Temperature

CaCu3Ti4O12(CCTO) is well known to have colossal dielectric constant in the range of 105.It is widely accepted that this phenomenon may be attributed to internal layer barrier capacitance (IBLC) model. The dielectric properties of CCTO were reported to be strongly dependent on the processing conditions and grain size. In this work, CCTO samples with different grain sizes were produced by varying sintering temperature in order to investigate IBLC effect on dielectric properties of CCTO. The samples were sintered at four different temperatures, (T=1100°C, 1050°C, 1000°C and 950°C). Dielectric measurements were carried out for the samples in the frequency range of 102– 106Hz using impedance spectrometer. Electron micrographs showed that increasing temperature promoted the grain growth of CCTO while sintering. The internal crystalline defects are seen to play major role by increasing the grain conductivity in dipole formation and increased the dielectric constant of the samples.

scholarly journals Dielectric properties and conductivity of PVdF-co-HFP/LiClO4 polymer electrolytes

2018 ◽  
Vol 96 (7) ◽  
pp. 786-791 ◽  
Author(s):  
Kemal Ulutaş ◽  
Ugur Yahsi ◽  
Hüseyin Deligöz ◽  
Cumali Tav ◽  
Serpil Yılmaztürk ◽  
...  
Keyword(s):  
Dielectric Constant ◽  
Dielectric Properties ◽  
Dielectric Loss ◽  
Polymer Electrolytes ◽  
Room Temperature ◽  
Solid Polymer Electrolytes ◽  
Solid Polymer ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Maximum Conductivity

In this study, it was aimed to prepare a series of PVdF-co-HFP based electrolytes with different LiClO4 loadings and to investigate their chemical and electrical properties in detail. For this purpose, PVdF-co-HFP based electrolytes with different LiClO4 loadings (1–20 weight %) were prepared using solution casting method. X-ray diffraction (XRD), differential scanning calorimetry, and thermogravimetric (TGA) –differential thermal and dielectric spectroscopy analysis of PVdF-co-HFP/LiClO4 were performed to characterize their structural, thermal, and dielectric properties, respectively. XRD results showed that the diffraction peaks of PVdF-co-HFP/LiClO4 electrolytes broadened and decreased with LiClO4. TGA patterns exhibited that PVdF-co-HFP/LiClO4 electrolytes with 20 wt % of LiClO4 had the lowest thermal stability and it degraded above 473 K, which is highly applicable for solid polymer electrolytes. Dielectric constant, dielectric loss, and conductivities were calculated by measuring capacitance and dielectric loss factor of PVdF-co-HFP/LiClO4 in the range from 10 mHz to 20 MHz frequencies at room temperature. In consequence, conductivities of PVdF-co-HFP/LiClO4 increased significantly with frequency for low loading of LiClO4 while they only slightly changed with higher LiClO4 addition. On the other hand, dielectric constant values of PVdF-co-HFP/LiClO4 films decreased with frequency whereas they rose with LiClO4 addition. The dielectric studies showed an increase in dielectric constant and dielectric loss with decreasing frequency. This result was attributed to high contribution of charge accumulation at the electrode–electrolyte interface. The electrolyte showed the maximum conductivity of 8 × 10−2 S/cm at room temperature.

Effect of Fungicide Treatment on Dielectric Properties of a Vegetable Seed

2015 ◽  
Vol 5 (2) ◽  
Author(s):  
Vishal Singh Chandel ◽  
Atiq UR Rahmanm ◽  
J. P. Shukla ◽  
Rajiv Manohar ◽  
Mohd. Shafi Khan
Keyword(s):  
Dielectric Constant ◽  
Dielectric Properties ◽  
Dielectric Loss ◽  
Moisture Content ◽  
Considerable Change ◽  
Frequency Range ◽  
Dielectric Parameters ◽  
Hewlett Packard ◽  
Fungicide Treatment ◽  
Vegetable Seed

Effect of fungicides' (thiram, captan, carbendazim, bagalol) treatment on dielectric constant and dielectric loss of a vegetable seed, namely the brinjal at given moisture content and bulk density was examined using Hewlett-Packard (HP-4194A) impedance/gain phase analyzer over the frequency range of 0.01 to 10 MHz and temperature range of 30-450C. Julabo (temperature controller, F-25, Germany) was used for keeping the temperature of seeds constant. Study showed that fungicide treatment cast considerable change in dielectric parameters namely the dielectric constant and dielectric loss.

scholarly journals Study of Dielectric Properties of Fenugreek Seeds (Trigonella Foenum Graecum)

2014 ◽  
Vol 66 (1) ◽  
pp. 17-28 ◽  
Author(s):  
Mohd. Shafi Khan ◽  
Vishal Singh Chandel ◽  
Rajiv Manohar ◽  
Jagdeesh Prasad Shukla
Keyword(s):  
Dielectric Constant ◽  
Dielectric Properties ◽  
Dielectric Loss ◽  
Moisture Content ◽  
Ac Conductivity ◽  
Frequency Range ◽  
Fenugreek Seeds ◽  
Temperature Controller ◽  
Trigonella Foenum Graecum ◽  
Fenugreek Seed

Abstract The present paper studied the dielectric constant, dielectric loss, and ac conductivity of fenugreek seed, a medicinal seed (Trigonella foenum graecum), within the frequency range of 10 kHz and 10 MHz and the temperature range of 30°C and 50°C. Impedance gain/phase analyser (HP 4194 A) was used to measure the dielectric constant and the dielectric loss and Julabo (temperature controller, F-25, Germany) was used for keeping the temperature of fenugreek seeds constant. It was found that the dielectric constant and the dielectric loss decrease with the increase in the frequency while the same increase with the increase in temperature and moisture content. The ac conductivity increased with the increase in frequency, moisture and temperature.

scholarly journals Dielectric and Conductivity Properties of Some Wood Composites

2016 ◽  
Vol 8 ◽  
pp. 51-60
Author(s):  
K.Ch. Varada Rajulu ◽  
B.N. Mohanty
Keyword(s):  
Dielectric Constant ◽  
Dielectric Properties ◽  
Dielectric Loss ◽  
Low Temperature ◽  
Temperature Region ◽  
Loss Factor ◽  
Wood Composites ◽  
Frequency Range ◽  
Increasing Temperature ◽  
Coaxial Probe

This study presents the dielectric and conductivity properties as function of temperature and frequency of wood based composites. These properties were measured by an open-ended coaxial probe at frequency range between 100 kHz to 100MHz, temperature from 30OC to 200OC which is fully computer interfaced. It has been observed that dielectric constant (ε') and dielectric loss factor (ε") increase with increasing temperature and decrease with increasing frequency. At low temperature region, the conductivity depends significantly on the frequency. However, with the increase in temperature dielectric relaxation takes place and the dependency of the conductivity on frequency get reduced. The patterns of variation were established for the studied specimens and discrepancies were discussed. The study of dielectric properties will help in improving the drying, heating and gluing processes of wood and wood based products.

Bulk and In-Circuit Dielectric Characterization of LTCC Tape Systems Through Millimeter Wave Frequency Range

2011 ◽  
Vol 2011 (1) ◽  
pp. 000740-000746 ◽  
Author(s):  
Bradley Thrasher ◽  
Deepukumar Nair ◽  
James Parisi ◽  
Glenn Oliver ◽  
Michael A. Smith
Keyword(s):  
Dielectric Constant ◽  
Dielectric Properties ◽  
Millimeter Wave ◽  
Design Stage ◽  
Frequency Range ◽  
Dielectric Thickness ◽  
Dielectric Characterization ◽  
Wide Range ◽  
Comprehensive Characterization

Low Temperature Co-fired Ceramic (LTCC) material systems offer a highly versatile microwave and millimeter wave packaging platform. Extremely low microwave loss, excellent control of dielectric constant, uniform dielectric thickness, non-existent water absorption leading to very high hermeticity, ability to support multilayer structure leading to 3-dimensional packaging, ability to embed passive functions within the tape layers, availability of a wide range of metallizations, etc. are some of the key advantages of LTCC for microwave packaging. One of the important parameters which needs to be determined at the very early stages of circuit designs are the dielectric properties - dielectric constant and loss tangent, both of which are functions of frequency. These properties need to be known accurately over the entire frequency range of operation for the circuit. For LTCC based designs, the use of dielectric constant of bulk material can lead to deviations between the performance expected at the design stage and for the fabricated circuit. Such deviations are a significant concern for broadband circuits as well as for circuits with sharp resonant behavior such as filters. One of the significant sources of deviation between bulk LTCC and “in-circuit” dielectric constant is the nature of the thick film metallizations used in LTCC technology. Work described here is a comprehensive characterization of three DuPont™ GreenTape™ LTCC systems 951, 943, and 9K7 - in the frequency range 10 to 70 GHz. Both bulk and “in-circuit” dielectric properties with silver and gold metallizations are studied to quantify the deviations in dielectric properties. A Fabry-Perot open resonator technique is used for the bulk characterization while printed ring resonators are used for the in-circuit characterization. This comprehensive characterization will provide key design data for LTCC designers in the 10 – 70 GHz frequency range.

The synthesis, photophysical and dielectric properties of ball-type dinuclear zinc phthalocyanine

2012 ◽  
Vol 16 (07n08) ◽  
pp. 826-832 ◽  
Author(s):  
Mevlüde Canlıca ◽  
Ahmet Altındal ◽  
Tebello Nyokong
Keyword(s):  
Dielectric Constant ◽  
Dielectric Properties ◽  
Dielectric Loss ◽  
Temperature Dependence ◽  
Zinc Phthalocyanine ◽  
Frequency Range ◽  
H Nmr ◽  
Peripheral Position ◽  
Ft Ir ◽  
Polarizability Contribution

The synthesis of ball-type dinuclear Zn(II) phthalocyanine containing four 4,4′-(9H-fluorene-9,9-diyl)diphenol substituents at the non-peripheral position is presented. The structure of the synthesized compound was characterized using elemental analyzes, and UV-vis, FT-IR,1H NMR and mass spectroscopies. The ΦFvalue was 0.16 and ΦTvalue was 0.72. The complex showed reasonably long triplet lifetimes with τT7210 μs in DMSO. The frequency and temperature dependence of the dielectric properties of ZnPc were also investigated in the frequency range of 40–105Hz and in the temperature range of 300–440 °K. It has been observed that both dielectric constant ε′ and dielectric loss ε″ decrease with the rise in frequency as they increase with the rise in temperature. The decrease in ε′ with increasing frequency is attributed to the fact that as the frequency increases, the polarizability contribution from orientation sources decreases and finally disappears.

Dielectric properties of normal, reduced, and specially reduced rutile (TiO2) single crystals at room temperature

1969 ◽  
Vol 47 (1) ◽  
pp. 3-6 ◽  
Author(s):  
H. B. Lal ◽  
K. G. Srivastava
Keyword(s):  
Dielectric Constant ◽  
Relaxation Time ◽  
Dielectric Properties ◽  
Dielectric Loss ◽  
Oxygen Vacancy ◽  
Single Crystals ◽  
Room Temperature ◽  
Interfacial Polarization ◽  
Absorption Peak ◽  
Single Relaxation Time

The variation of the dielectric constant (ε′) and the dielectric loss (ε″) have been studied as a function of frequency (102 to 1010 c.p.s.) for normal (as grown), reduced (heated in vacuum), and specially reduced (heated in vacuum in presence of an asymmetric d.c. field) rutile single crystals parallel to c-axis at room temperature. Dispersions in ε′ have been observed in the frequency ranges 102 to 103 and 107 to 109 c.p.s. for all the samples with absorption peaks in ε″ at 2 × 102 and 6 × 107 c.p.s. Also an extra absorption peak in ε″ has been found at 2 × 104 c.p.s. for the specially reduced sample. The absorption peak at 2 × 102 c.p.s. has been observed by many workers and is typical for interfacial polarization. The peak at 6 × 107 c.p.s. appears to be due to a dipole rotation process with a single relaxation time and is identified as due to relaxation of dipoles formed between Ti3+ and a neighboring oxygen vacancy. The possible mechanism of relaxation for the 2 × 104 c.p.s. absorption peak is also discussed.

Sign in / Sign up

Export Citation Format

Share Document