A MODEL FOR ESTIMATION OF THE CONTRIBUTION OF FLY ASH TO CONCRETE STRENGTH

1991 ◽  
pp. 263-277
Author(s):  
Sandor Popovics
Keyword(s):  
Fly Ash ◽  
Concrete Strength

Effect of ground granulated blast funrnace slag and fly ash on strength, permeability, and under-water abrasion of fine-grained concrete

2020 ◽  
Vol 71 (7) ◽  
pp. 775-788
Author(s):  
Quyet Truong Van ◽  
Sang Nguyen Thanh
Keyword(s):  
Fly Ash ◽  
Concrete Strength ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Chloride Permeability ◽  
Cement Replacement ◽  
Fine Grained ◽  
Granulated Blast Furnace Slag ◽  
Compressive Strength Test ◽  
Economic Ground

The utilisation of supplementary cementitious materials (SCMs) is widespread in the concrete industry because of the performance benefits and economic. Ground granulated blast furnace slag (GGBFS) and fly ash (FA) have been used as the SCMs in concrete for reducing the weight of cement and improving durability properties. In this study, GGBFS at different cement replacement ratios of 0%, 20%, 40% and 60% by weight were used in fine-grained concrete. The ternary binders containing GGBFS and FA at cement replacement ratio of 60% by weight have also evaluated. Flexural and compressive strength test, rapid chloride permeability test and under-water abrasion test were performed. Experimental results show that the increase in concrete strength with GGBFS contents from 20% to 40% but at a higher period of maturity (56 days and more). The chloride permeability the under-water abrasion reduced with the increasing cement replacement by GGBFS or a combination of GGBFS and FA

scholarly journals Effects of microbial agents to the properties of fly ash-based paste

2018 ◽  
Vol 195 ◽  
pp. 01012
Author(s):  
Kiki Dwi Wulandari ◽  
Januarti Jaya Ekaputri ◽  
Triwulan ◽  
Chikako Fujiyama ◽  
Davin H. E. Setiamarga
Keyword(s):  
Fly Ash ◽  
Portland Cement ◽  
Cement Paste ◽  
Construction Material ◽  
Concrete Strength ◽  
Self Healing ◽  
Concrete Mixtures ◽  
Microbial Agents ◽  
Portland Cement Paste ◽  
Geopolymer Paste

Specific microbial agents such as bacteria are often used in concrete to improve its performance. Some microbes act as self-healing agents to close cracks in concrete, and to increase concrete strength. This paper presents a study to observe the effects of microbe addition to two types of concrete mixtures the fly ash-based, as geopolymer paste, and portland cement paste containing fly ash. Furthermore, the investigation was conducted to compare the properties of each paste, such as its compressive strengths, specific gravities, porosity, microstructures, and XRay diffracting properties. The results indicate that microbial activities positively affected the properties of both, portland cement paste and geopolymer paste. The result reported here strongly suggests that fly ash can be used to produce a high quality, but environmental friendly construction material when it’s mixed together with useful microbes.

On Effects of Fly Ash as a Partial Replacement of Cement on Concrete Strength

2012 ◽  
Vol 204-208 ◽  
pp. 3970-3973
Author(s):  
Reagan J. Case ◽  
Kai Duan ◽  
Thuraichamy G. Suntharavadivel
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Concrete Strength ◽  
Cementitious Materials ◽  
Partial Replacement ◽  
Replacement Ratio ◽  
Interface Reactions ◽  
Compressive Strength Of Concrete ◽  
Interface Bonding Strength ◽  
Large Research

As a part of a large research program aiming at the cementitious materials containing recycled materials at Central Queensland University – Australia, the current paper presents the preliminary results of a study on the effects of fly ash, which is used to replace cement in concrete, on the concrete compressive strength. For this purpose, systematic experiments have been carried out to investigate the influences of fly ash ratio and age. The compressive strength of concrete specimens with replacement ratios of 15%, 30% and 45%, and aged 7 and 28 days are measured and are compared with those of the concrete specimens without fly ash at the same ages. The results demonstrate that the strength of fly ash containing concrete improves more slowly but more strongly with aging, than their fly ash free counterparts, and an optimum fly ash replacement ratio exists where the maximum compressive strength of fly ash containing concrete can be achieved, and the maximum strength for the specimens aged 28 days and above is higher that of fly ash free concrete. Furthermore, the observation strength behaviours are analysed and discussed in terms of the influences of fly ash on interface reactions and interface bonding strength.

scholarly journals Durability of Structural Lightweight Concrete with Sintered Fly Ash Aggregate

Materials ◽  
2020 ◽  
Vol 13 (20) ◽  
pp. 4565 ◽  
Author(s):  
Lucyna Domagała
Keyword(s):  
Fly Ash ◽  
Moisture Content ◽  
Water Absorption ◽  
Water Permeability ◽  
Lightweight Concrete ◽  
Concrete Strength ◽  
Initial Moisture Content ◽  
Cement Matrix ◽  
Secondary Importance ◽  
Freeze Thaw

The aim of this study was to present the problem of durability of structural lightweight concrete made of a sintered fly ash aggregate. The issue of durability was researched for 12 concrete series in terms of their water absorption, water permeability, and freeze-thaw resistance. Additionally, the microstructure of several concretes was analyzed with a scanning electron microscope (SEM). In the durability research, the influences of the following parameters were taken into consideration: The initial moisture content of sintered fly ash (mc = 0, 17–18, and 24–25%); the aggregate grading (4/8 and 6/12 mm); and the water-cement ratio (w/c = 0.55 and 0.37). As a result of various compositions, the concretes revealed different properties. The density ranged from 1470 to 1920 kg/m3, and the corresponding strength ranged from 25.0 to 83.5 MPa. The durability research results of tested lightweight concretes showed that, despite considerably higher water absorption, a comparable water permeability and comparable or better freeze-thaw resistance in relation to normal-weight concrete may be present. Nevertheless, the fundamental requirement of lightweight concrete to achieve good durability requires the aggregate’s initial moisture content to be limited and a sufficiently tight cement matrix to be selected. The volume share of the cement matrix and aggregate, the cement content, and even the concrete strength are of secondary importance.

scholarly journals Impact of Climate Change on the Optimization of Mixture Design of Low-CO2 Concrete Containing Fly Ash and Slag

2019 ◽  
Vol 11 (12) ◽  
pp. 3394 ◽  
Author(s):  
Xiao-Yong Wang
Keyword(s):  
Climate Change ◽  
Genetic Algorithm ◽  
Fly Ash ◽  
Co2 Emissions ◽  
Concrete Strength ◽  
Mixture Design ◽  
Control Factor ◽  
Climate Change Scenarios ◽  
Low Co2 ◽  
Carbonation Resistance

Fly ash and slag have been widely used to produce low-CO2 concrete. However, previous studies have not paid enough attention to the lower carbonation resistance of fly-ash-and-slag-blended concrete and the aggravations of carbonation due to climate change. This study proposes a technique for the design of fly-ash-and-slag-blended concrete considering carbonation durability coupled with various climate change scenarios. First, CO2 emissions are evaluated from concrete mixtures. Concrete strength and carbonation depth are evaluated using efficiency factors of fly ash and slag. A genetic algorithm (GA) is used to find the optimal mixture with the lowest CO2 emissions considering the requirements of strength, carbonation durability, and workability. Second, we clarify the effect of cost on the mixture design of low-CO2 concrete. A genetic algorithm is also used to find the optimal mixture with the lowest cost. We found that the optimal mixture with the lowest cost is different from that with the lowest CO2 emissions. Third, by adding the additional constraint of cost, Pareto optimal mixtures are determined, which consider both lower CO2 emissions and lower material cost. The analysis results show that carbonation durability is the control factor of mixture design of fly ash-slag blended concrete. To mitigate the challenge of climate change, the binder content of blended concrete should be increased.

Experiment and Mechanism Study on Effect of Water/Binder and Fly Ash on Mechanical Properties of HPC

2011 ◽  
Vol 255-260 ◽  
pp. 3404-3410
Author(s):  
Shuang Xi Li ◽  
An Quan Xu ◽  
Xin Jun Tang ◽  
Quan Hu
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Concrete Strength ◽  
Early Period ◽  
Point Of View ◽  
Mechanism Study ◽  
Compressive Strength Test ◽  
Large Water

It takes on the technical and economic double benefits that fly ash taking the place of cement. However, water/binder of modern concrete is generally low; the research on the concrete performance which is based on large water/binder is no longer suitable for analysis of modern concrete. As to this problem, using different proportions of W/B and FA dosage as influencing factors, specimen is compounded for the compressive strength test. Then, mechanical properties of HPC are studied systematically. Based on this, macro-performance is analyzed from a micro-mechanism point of view through taking the electron micrograph. As the study shows, strength of HPC mixed with fly ash has low characteristics at early period while high ones at later period. At later hydration, fly ash effect plays a significant role, the growth rate of concrete strength increases as the increase of FA dosage. Compressive strength of concrete decreases as the increase of W/B and FA dosage. When the W/B is high, compressive strength is not sensitive to the change of W/B and FA dosage; but when the W/B decreases from 0.30 to 0.25, the concrete strength transition occurs. The influence of W/B on concrete compressive strength is more significant than that of the FA dosage; in the preparation of HPC, fly ash can be added more and cement is added less relatively by decreasing the W/B, displaying the role of micro-aggregate filling and modification, improving the strength and other performance of concrete. The study on micro-mechanism proves well the macro-phenomena above.

Study on the Strength of Sea Sand Concrete in Ningbo

2011 ◽  
Vol 250-253 ◽  
pp. 262-265
Author(s):  
Jun Zhe Liu ◽  
Guo Liang Zhang ◽  
Jian Bin Chen ◽  
Zhi Min He
Keyword(s):  
Fly Ash ◽  
Influence Factor ◽  
Concrete Strength ◽  
Chloride Ion ◽  
Strength Development ◽  
Term Strength ◽  
Two Phase ◽  
Sea Sand ◽  
Early Strength

This paper mainly explain and expounded folding compressive strength of the different types of sea sand mortar , fly ash to the sea sand concretes mortar intensity influence as well as the chloride ion content to the sea sand concretes mortar intensity influence. The pulverized fly ash has the postponement function to the sea sand concretes early strength, the chloride ion has the promoter action to the sea sand concretes early strength. 20% pulverized fly ash be good to the sea sand concretes long-term strength development influence, can achieve the goal which enhances the sea sand concretes the long-term strength . The chloride ion is greater to the concretes early strength influence, especially in previous 3 days. Along with the time development, the chloride ion influence weakens, but the pulverized fly ash enlarges to the concretes intensity's influence factor. A two-phase arrived, the final concrete strength values close to each other.

Prediction of the Strength Development of Fly Ash Concrete

2010 ◽  
Vol 150-151 ◽  
pp. 1026-1033 ◽  
Author(s):  
Ming Hui Liu ◽  
Yuan Feng Wang
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Concrete Strength ◽  
Strength Development ◽  
Standard Temperature ◽  
Development Models ◽  
Fly Ash Concrete ◽  
Strength Tests ◽  
Maturity Method ◽  
Predicted Model

The effect of fly ash in improving the mechanical properties of concrete is investigated and the existing concrete strength development models are studied. Based on the chemic reactivity properties between fly ash and cement, an appropriate concrete strength model are chosen, and a new model for the fly ash strength factor combing Maturity method is built up and the factors are regressed by existing experimental datum. A total of 24 concretes, including two concretes were produced with two partial fly ash replacement ratios (23.7%, 32.7%). The cubic samples produced from ash fly concrete were demoulded after a day, and cured at standard temperature ( in GB/T 50081-2002) with 100% relative humidity until 28 days, then cured in water. The compressive strength tests were carried out on the cubic specimens at different ages. The compressive strength with time was evaluated by using the new predicted model. It was found that the calculated results by new method are fit the experimental data well.

Effects of Fly Ash Particle Sizes on the Compressive Strength and Fracture Toughness of High Performance Concrete

2011 ◽  
Vol 284-286 ◽  
pp. 984-988
Author(s):  
An Shun Cheng ◽  
Yue Lin Huang ◽  
Chung Ho Huang ◽  
Tsong Yen
Keyword(s):  
Fracture Toughness ◽  
Particle Size ◽  
Compressive Strength ◽  
Fly Ash ◽  
High Performance ◽  
High Performance Concrete ◽  
Concrete Strength ◽  
Bending Test ◽  
Strength Development ◽  
Particle Sizes

The study aims to research the effect of the particle size of fly ash on the compressive strength and fracture toughness of high performance concrete (HPC). In all HPC mixtures, the water-to-binder ratio selected is 0.35; the cement replacement ratios includes 0%, 10% and 20%; the particle sizes of fly ash have three types of passing through sieves No. 175, No. 250 and No. 325. Three-point-bending test was adopted to measure the load-deflection relations and the maximum loads to determine the fracture energy (GF) and the critical stress intensity factor (KSIC). Test results show that adding fly ash in HPC apparently enhances the late age strengths of HPC either for replacement ratio of 10% or 20%, in which the concrete with 10% fly ash shows the higher effect. In addition, the smaller the particle size is the better the late age concrete strength will be. The HPC with the finer fly ash can have higher strength development and the values of GF and KSIC due to the facts of better filling effect and pozzolanic reaction. At late age, the GF and KSIC values of concrete with 10% fly ash are all higher than those with 20% fly ash.

Sign in / Sign up

Export Citation Format

Share Document