An Investigation of Steady and Unsteady Flow through a Napier Turboblower Turbine under Conditions of Full and Partial Admission

1968 ◽  
Vol 183 (1) ◽  
pp. 615-630 ◽  
Author(s):  
H. R. M. Craig ◽  
K. J. Edwards ◽  
J. H. Horlock ◽  
M. Janota ◽  
R. Shaw ◽  
...  
Keyword(s):  
Unsteady Flow ◽  
Mass Flow ◽  
Power Output ◽  
Axial Flow ◽  
Limited Range ◽  
Expansion Ratio ◽  
Operating Conditions ◽  
Turbine Efficiency ◽  
Cyclic Operation ◽  
Partial Admission

The paper presents the results of tests on an axial-flow turbine and describes how they are obtained, in steady and unsteady flow. An analysis of turbine-test results obtained under the unsteady operating conditions is then given. It is shown that over a limited range of cyclic operation the mass flow and power output may be predicted by assuming that the turbine operates instantaneously as it would under steady-flow conditions (at the same expansion ratio and the same non-dimensional rotational speed) and integrating over the engine cycle. At high pressure ratios, pulse frequencies and rotational speeds, this ‘quasi-steady’ analysis gives a slight overestimate of mass flow and power output but the error in turbine efficiency is very small.

Comparison of Partial vs Full Admission for Small Turbines at Low Specific Speeds

1985 ◽  
Author(s):  
Ennio Macchi ◽  
Giovanni Lozza
Keyword(s):  
Axial Flow ◽  
Design Procedure ◽  
Optimization Method ◽  
Expansion Ratio ◽  
Operating Conditions ◽  
Design Parameters ◽  
Basic Design ◽  
Partial Admission ◽  
Specific Speed ◽  
The One

Several methods are available for the optimization of basic design parameters and the preliminary efficiency prediction of axial flow turbine stages. However, their application is often questionable for stages having low specific speed and/or small volume flow rates. In particular, the question may arise whether a better performance is achieved by a partial admission, impulse stage or by a full admission reaction stage having lower blade height. The paper firstly reviews the available loss correlation methods applicable to partial admission turbines, then a comparison is performed between the efficiency achievable by partial and full admission stages designed for the same operating conditions. The turbine design procedure for both options is fully automatized by an efficiency optimization method similar to the one described in previous authors’ papers. The results of calculations are presented in the paper as a function of similarity parameters (specific speed, size parameter, expansion ratio). It is found that the results obtained with different correlations are relatively similar for “conventional” turbine stages (low expansion ratio, moderate size parameters), while important differences take place for very small sizes and/or in presence of important compressibility effects. The presented results can be useful: 1) to decide whether selecting full or partial admission solutions; 2) to optimize the degree of admission and the other basic design parameters, and 3) to predict with reasonable accuracy the stage efficiency.

scholarly journals Aerodynamic Analysis of Multistage Turbomachinery Flows in Support of Aerodynamic Design

1999 ◽  
Author(s):  
John J. Adamczyk
Keyword(s):  
Unsteady Flow ◽  
Axial Flow ◽  
Operating Conditions ◽  
Design Environment ◽  
Cfd Simulations ◽  
Average Flow ◽  
Flow Models ◽  
Time Average ◽  
Semi Empirical ◽  
Future Work

This paper summarizes the state of 3D CFD based models of the time average flow field within axial flow multistage turbomachines. Emphasis is placed on models which are compatible with the industrial design environment and those models which offer the potential of providing credible results at both design and off-design operating conditions. The need to develop models which are free of aerodynamic input from semi-empirical design systems is stressed. The accuracy of such models is shown to be dependent upon their ability to account for the unsteady flow environment in multistage turbomachinery. The relevant flow physics associated with some of the unsteady flow processes present in axial flow multistage machinery are presented along with procedures which can be used to account for them in 3D CFD simulations. Sample results are presented for both axial flow compressors and axial flow turbines which help to illustrate the enhanced predictive capabilities afforded by including these procedures in 3D CFD simulations. Finally, suggestions are given for future work on the development of time average flow models.

Impact of the Expansion Ratio on the Unsteady Aerodynamics and Performance of a HP Axial Turbine

2016 ◽  
Author(s):  
P. Gaetani ◽  
G. Persico ◽  
A. Spinelli ◽  
A. Mora
Keyword(s):  
Flow Field ◽  
Incidence Angle ◽  
Flow Direction ◽  
Axial Flow ◽  
Unsteady Aerodynamics ◽  
Fast Response ◽  
Expansion Ratio ◽  
Operating Conditions ◽  
Inlet Temperature ◽  
And Performance

In the frame of the European research project RECORD, the flow field within a HP axial-flow turbine model was investigated experimentally for several operating conditions. A number of studies on stator-rotor interaction in HP turbines for subsonic as well as transonic/supersonic conditions were proposed in the last decades, but none of them compared different conditions for the same geometry. In this paper, the transonic condition is investigated and compared to three subsonic ones, in the frame of an entirely new experimental campaign. The research was performed at the Laboratorio di Fluidodinamica delle Macchine of the Politecnico di Milano (Italy), where a cold-flow, closed-loop test rig is available for detailed studies on turbines and compressors. The boundary conditions resulted in keeping constant both the turbine inlet temperature and the stage outlet absolute flow direction; so far, while the expansion ratio was varied, the rotational speed was also modified accordingly. The analysis was performed by means of a conventional five hole probe in the stator – rotor axial gap and by a fast response aerodynamic probe downstream of the rotor. The local time-averaged and phase-resolved flow field was then derived and used to analyze the stage aerodynamics and performance. Results show that the stage expansion ratio has a dramatic impact on both the rotor aerodynamics and stage performance. In particular, Mach number effects are recognized in the stator cascade that passes from transonic to low subsonic conditions. On the rotor cascade the reduction of expansion ratio reduces significantly the Mach and Reynolds numbers and increases the incidence angle as well; the rotor loss mechanics as well as the vane-rotor interaction are greatly amplified. Correspondingly a significant variation of stage overall efficiency is recorded.

Experimental investigation and optimization of a low-temperature thermoelectric module with different operating conditions

2019 ◽  
Vol 16 (3) ◽  
pp. 368-376
Author(s):  
Dipak Sudam Patil ◽  
Rachayya R. Arakerimath ◽  
Pramod V. Walke
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Power Output ◽  
External Load ◽  
Thermoelectric Module ◽  
Load Resistance ◽  
Operating Conditions ◽  
Content Type ◽  
Heater Temperature

Purpose This paper aims to present an experimental investigation and optimization of a low-temperature thermoelectric module to examine the influence of the main operating conditions. Design/methodology/approach In this work, a comparison was made by varying the various operating parameters such as heat source temperature, the flow rate of the cold fluid and the external load resistance. A Taguchi method was applied to optimize the parameters of the system. Three factors, including the external load resistance, mass flow rate of water (at the heat sink side) and heater temperature (at the heat source side) along with different levels were taken into account. Analysis of variance was used to determine the significance and percentage contribution of each parameter. Findings The experimental results show that the maximum power output 8.22W and the maximum conversion efficiency 1.11 per cent were obtained at the heater temperature of 240°C, the cold fluid mass flow rate of 0.017 kg/s, module temperature difference of 45°C and the load resistance of 5 O. It was observed that the optimum parameter levels for maximum power output determined as 5 O external load resistance, 0.17 kg/s mass flow rate of water and 240°C heater temperature (A1B3C3). It reflects that these parameters influence on the optimum conditions. The heater temperature is the most significant parameter on the power output of the thermoelectric module. Originality/value It is clear from the confirmation test that experimental values and the predicted values are in good agreement.

Experimental Investigation of Stepped Tip Gap Effects on the Performance of a Transonic Axial-Flow Compressor Rotor

1998 ◽  
Vol 120 (3) ◽  
pp. 477-486 ◽  
Author(s):  
D. W. Thompson ◽  
P. I. King ◽  
D. C. Rabe
Keyword(s):  
Mass Flow ◽  
Pressure Ratio ◽  
Axial Flow ◽  
Operating Conditions ◽  
Tip Clearance ◽  
Axial Flow Compressor ◽  
Transonic Compressor ◽  
Compressor Rotor ◽  
Percent Improvement ◽  
Flow Compressor

The effects of stepped-tip gaps and clearance levels on the performance of a transonic axial-flow compressor rotor were experimentally determined. A two-stage compressor with no inlet guide vanes was tested in a modern transonic compressor research facility. The first-stage rotor was unswept and was tested for an optimum tip clearance with variations in stepped gaps machined into the casing near the aft tip region of the rotor. Nine causing geometries were investigated consisting of three step profiles at each of three clearance levels. For small and intermediate clearances, stepped tip gaps were found to improve pressure ratio, efficiency, and flow range for most operating conditions. At 100 percent design rotor speed, stepped tip gaps produced a doubling of mass flow range with as much as a 2.0 percent increase in mass flow and a 1.5 percent improvement in efficiency. This study provides guidelines for engineers to improve compressor performance for an existing design by applying an optimum casing profile.

Conceptual Design of an Axial Turbocharger Turbine

2017 ◽  
Author(s):  
Apostolos Pesiridis ◽  
Antonio Ferrara ◽  
Raffaele Tuccillo ◽  
Hua Chen
Keyword(s):  
Internal Combustion Engines ◽  
Fluid Dynamic ◽  
Axial Flow ◽  
Initial Response ◽  
Operating Conditions ◽  
Combustion Engines ◽  
Turbine Efficiency ◽  
Transient Events ◽  
Engine Operating Point ◽  
Original Concept

Despite engine turbocharging being a widespread technology, there are still drawbacks present in current turbocharging systems stemming from the apparent mismatch between the periodic operation of a piston engine operating in conjunction with an essentially steady-state, rotordynamic machine (turbocharger). The primary issue remains the provision of adequate transient response thereby suppressing the issue of turbocharger lag (turbo-lag) or the poor initial response of the turbocharger to driver-commanded, engine operating point changes due to its inertia. Another problem is engine-turbocharger matching and operation under pulsating conditions in the exhaust manifold and generally unsteady engine operating conditions. The exhaust flows of internal combustion engines are characterized by pulsating flows at constant engine speeds (local pulsating effect) as well as “global” unsteadiness during engine transient events. Because of the volute volume and the length of the flow path, this unsteadiness generates a phase shift between mass flow, temperature and pressure at rotor inlet, and a stronger circumferential variation of the rotor inlet condition than in steady flow conditions. The shift and the variation increase the losses in the turbine, resulting in lower turbine efficiency. The current paper develops original concept work carried out at Brunel University London to develop an innovative fluid-dynamic design for an axial turbine for turbocharger application. An axial flow turbine coupled with a specially-designed, outflow volute, arranged in a non-classical way, are the target of this work. CFD analysis and 1D simulation of an engine coupled with the innovative turbine have been performed to highlight the design potential.

The 2-Stage Axial Turbine Test Facility “LISA”

2001 ◽  
Author(s):  
M. Sell ◽  
J. Schlienger ◽  
A. Pfau ◽  
M. Treiber ◽  
R. S. Abhari
Keyword(s):  
Unsteady Flow ◽  
Mass Flow ◽  
Measurement Techniques ◽  
Operating Conditions ◽  
Test Facility ◽  
Two Stage ◽  
Axial Turbine ◽  
Aerodynamic Pressure ◽  
Second Stage ◽  
The Impact

This paper describes the design and construction of a new two stage axial turbine test facility, christened “Lisa”. The research objective of the rig is to study the impact (relevance) of unsteady flow phenomena upon the aerodynamic performance, this being achieved through the use of systematic studies of parametric changes in the stage geometry and operating point. Noteworthy in the design of the rig is the use of a twin shaft arrangement to decouple the stages. The inner shaft carries the load from the first stage whilst the outer is used with an integral torque-meter to measure the loading upon the second stage alone. This gives an accurate measurement of the loading upon the aerodynamically representative second stage, which possesses the correct stage inlet conditions in comparison to the full two stage machine which has an unrealistic axial inlet flow at the first stator. A calibrated Venturi nozzle measures the mass flow at an accuracy of below 1%, from which stage efficiencies can be derived. The rig is arranged in a closed loop system. The turbine has a vertical arrangement and is connected through a gear box to a generator system that works as a brake to maintain the desired operating speed. The turbine exit is open to ambient pressure. The rig runs at a low pressure ratio of 1.5. The maximum Mach number at stator exit is 0.3 at an inlet pressure of 1.5 bar. The maximum mass flow is 14 kg/sec. Nominal rotor design speed is 3000 RPM. The tip to hub blade ratio is 1.29, and the nominal axial chord is 50 mm. The rig is designed to accommodate a broad range of measurement techniques, but with a strong emphasis upon unsteady flow methods, for example fast response aerodynamic pressure probes for time-resolved flow measurements. The first section of this paper describes the overall test facility hardware. This is followed by a detailed focus on the torque measurement device including stage efficiency measurements at operating conditions in Lisa. Discussion of measurement techniques completes the paper.

Experimental Investigation of Stepped Tip Gap Effects on the Performance of a Transonic Axial-Flow Compressor Rotor

1997 ◽  
Author(s):  
Donald W. Thompson ◽  
Paul I. King ◽  
Douglas C. Rabe
Keyword(s):  
Mass Flow ◽  
Pressure Ratio ◽  
Axial Flow ◽  
Operating Conditions ◽  
Tip Clearance ◽  
Axial Flow Compressor ◽  
Transonic Compressor ◽  
Compressor Rotor ◽  
Compressor Performance ◽  
Flow Compressor

The effects of stepped tip gaps and clearance levels on the performance of a transonic axial-flow compressor rotor were experimentally determined. A two-stage compressor with no inlet guide vanes was tested in a modern transonic compressor research facility. The first-stage rotor was unswept and was tested for an optimum tip clearance with variations in stepped gaps machined into the casing near the aft tip region of the rotor. Nine casing geometries were investigated consisting of three step profiles at each of three clearance levels. For small and intermediate clearances, stepped tip gaps were found to improve pressure ratio, efficiency, and flow range for most operating conditions. At 100% design rotor speed, stepped tip gaps produced a doubling of mass flow range with as much as a 2.0% increase in mass flow and a 1.5% improvement in efficiency. This study provides guidelines for engineers to improve compressor performance for an existing design by applying an optimum casing profile.

Unsteady Flow Analysis of the Stator-Rotor Interaction in an Axial Flow Fan

2003 ◽  
Author(s):  
J. Ferna´ndez Oro ◽  
K. Argu¨elles Di´az ◽  
C. Santolaria Morros ◽  
R. Ballesteros Tajadura
Keyword(s):  
Unsteady Flow ◽  
Flow Analysis ◽  
Flow Characteristics ◽  
Axial Flow ◽  
3D Models ◽  
Operating Conditions ◽  
Rotor Blades ◽  
Axial Flow Fan ◽  
Rotating Blade ◽  
Flow Phenomena

In the usual operation of turbomachinery, some unsteady flow phenomena appear due to the non uniformity of the flow inside the rotor, when observed in the fixed reference frame. These phenomena are often related to the unsteady character of the pressure and velocity fields, which produce oscillating forces on the blades, superimposed to the steady force. These oscillating forces are the main mechanism of noise generation, which appear even at a constant rotational speed and at flow rates where the performance curves are stable. In axial turbomachines, the interaction is due to relative motion between the static and rotating blade rows. Considering the case of a fixed blade row (stator) placed upstream of the rotor, the non uniform flow leaving those blades (usually referred as IGV blades) is observed as an unsteady flow by the rotor blades. The effect of this interaction is the generation of unsteady forces on the rotor blades, which generate vibrations (risk of fatigue failure) and noise, and non-uniformity and unsteadiness of the pressure field, that propagates as an acoustic wave. The first part of this work is a brief description of a URANS numerical modeling of the unsteady flow characteristics of a one-stage subsonic axial flow fan with a reaction degree greater than 1. The focus is placed on the statorrotor interaction performance. Both 2D and 3D models of the fan, with 13 IGV’s and 9 rotor blades, were developed and an unsteady simulation was achieved to carry out the main characteristics of the flow inside the turbomachine. Once the actuating forces are determined, the influence of the radial position, the operating conditions and the distance of the fixed and the rotating blade rows is also analyzed. The final part of the paper is focused over the identification, through the definition of deterministic stresses — related to the characteristic blade-passage frequency of every row — that provoke the interaction between fixed and rotating blade rows and its evolution through time. The object is to obtain, in a stress tensor form, the contribution of the velocity field, that is changing because of the sucessive relative positions between blade rows, to the pressure distribution over the blade surfaces in the interior of the stage. Finally, a map of deterministic stresses and even, deterministic kinetic energy, can be obtained to show the influence of the blade rows in the interaction, unsteady phenomena.

scholarly journals Aerodynamic Analysis of Multistage Turbomachinery Flows in Support of Aerodynamic Design

1999 ◽  
Vol 122 (2) ◽  
pp. 189-217 ◽  
Author(s):  
John J. Adamczyk
Keyword(s):  
Unsteady Flow ◽  
Axial Flow ◽  
Operating Conditions ◽  
Aerodynamic Design ◽  
Design Environment ◽  
Cfd Simulations ◽  
Flow Models ◽  
Flow Processes ◽  
Design Systems ◽  
Future Work

This paper summarizes the state of 3D CFD based models of the time-averaged flow field within axial flow multistage turbomachines. Emphasis is placed on models that are compatible with the industrial design environment and those models that offer the potential of providing credible results at both design and off-design operating conditions. The need to develop models free of aerodynamic input from semiempirical design systems is stressed. The accuracy of such models is shown to be dependent upon their ability to account for the unsteady flow environment in multistage turbomachinery. The relevant flow physics associated with some of the unsteady flow processes present in axial flow multistage machinery are presented along with procedures that can be used to account for them in 3D CFD simulations. Sample results are presented for both axial flow compressors and axial flow turbines that help to illustrate the enhanced predictive capabilities afforded by including these procedures in 3D CFD simulations. Finally, suggestions are given for future work on the development of time-averaged flow models. [S0889-504X(00)02002-X]

Sign in / Sign up

Export Citation Format

Share Document