scholarly journals Optimizing ZnO/CdS Nano Composite Controlled by Fe Doping Towards Efficiency in Water Treatment and Antimicrobial Activity

2021 ◽  
Vol 16 (3) ◽  
pp. 726-732
Author(s):  
Jayanta Barman ◽  
Archana Das ◽  
Bapan Banik ◽  
Farhana Sultana
Keyword(s):  
Antibacterial Effect ◽  
Rietveld Method ◽  
Fe Doping ◽  
X Ray Diffraction ◽  
Nano Composite ◽  
X Ray ◽  
Antibacterial Studies ◽  
Pure Phase ◽  
Uv Visible ◽  
Nanocrystalline Composite

Nanocrystalline composite zinc oxide (ZnO) and CdS with Fe doping thin films grown on glass substrate by chemical method. The parameters like temperature of the solution, UV exposure, pH of solution, immersion time, immersion cycles, have been controlled and standardized for nanocrystalline film. The synthesis NPs were analyzed by X-ray diffraction (XRD). Rietveld method shows that Fe-doped composite ZnO/CdS is a single pure phase and wurtzite structure. Samples were analyzed by sophisticated various instrument like XRD, UV- Visible spectrometer, HRTEM, HRSEM and composition was analyzed by EDX attached with HRTEM. The band gap was calculated by absorption spectroscopy and found that absorption was blue-shifted. The electron structure shows that doping changes the crystal structure and transition level create better efficiency and creates octahedral symmetry. The antibacterial studies showed that the 5.0 wt% Fe-doped exhibited maximum antibacterial effect.

Effect of Fe Doping on the Morphology of Hydrothermally Derived BaTiO3 Crystals

2012 ◽  
Vol 430-432 ◽  
pp. 12-15
Author(s):  
Lin Lin Yang ◽  
Yu Jiang Wang ◽  
Shun Li Huang ◽  
Yong Gang Wang
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Doping Concentration ◽  
Morphology Evolution ◽  
Fe Doping ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Hexagonal Shape ◽  
Pure Phase

Pure phase Fe doped BaTiO3 crystals have been successfully fabricated at 200°C with 0.7M KOH by a hydrothermal method. The obtained products were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). An obvious morphology evolution from hexagonal shape to sphericity was observed when Fe doping concentration was increased from 0% to 1%, 3%, 6%, and 10%. In addition, the size of the obtained Fe doped BaTiO3 crystals obviously became smaller. The possible mechanism was also discussed.

scholarly journals Controlled Synthesis of CuS and Cu9S5 and Their Application in the Photocatalytic Mineralization of Tetracycline

Catalysts ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 899
Author(s):  
Murendeni P. Ravele ◽  
Opeyemi A. Oyewo ◽  
Damian C. Onwudiwe
Keyword(s):  
Electron Microscopy ◽  
Visible Light ◽  
Blue Shift ◽  
X Ray Diffraction ◽  
X Ray ◽  
Copper Sulfides ◽  
Transmission Electron ◽  
Single Source Precursor ◽  
Pure Phase ◽  
Pure Phases

Pure-phase Cu2−xS (x = 1, 0.2) nanoparticles have been synthesized by the thermal decomposition of copper(II) dithiocarbamate as a single-source precursor in oleylamine as a capping agent. The compositions of the Cu2−xS nanocrystals varied from CuS (covellite) through the mixture of phases (CuS and Cu7.2S4) to Cu9S5 (digenite) by simply varying the temperature of synthesis. The crystallinity and morphology of the copper sulfides were studied using X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM), which showed pure phases at low (120 °C) and high (220 °C) temperatures and a mixture of phases at intermediate temperatures (150 and 180 °C). Covellite was of a spherical morphology, while digenite was rod shaped. The optical properties of these nanocrystals were characterized by UV−vis–NIR and photoluminescence spectroscopies. Both samples had very similar absorption spectra but distinguishable fluorescence properties and exhibited a blue shift in their band gap energies compared to bulk Cu2−xS. The pure phases were used as catalysts for the photocatalytic degradation of tetracycline (TC) under visible-light irradiation. The results demonstrated that the photocatalytic activity of the digenite phase exhibited higher catalytic degradation of 98.5% compared to the covellite phase, which showed 88% degradation within the 120 min reaction time using 80 mg of the catalysts. The higher degradation efficiency achieved with the digenite phase was attributed to its higher absorption of the visible light compared to covellite.

X-ray powder diffraction data of LaNi0.5Ti0.45Co0.05O3, LaNi0.45Co0.05Ti0.5O3, and LaNi0.5Ti0.5O3 perovskites

2021 ◽  
pp. 1-6
Author(s):  
Mariana M. V. M. Souza ◽  
Alex Maza ◽  
Pablo V. Tuza
Keyword(s):  
Crystal Structure ◽  
Rietveld Method ◽  
Pechini Method ◽  
Powder Diffraction Data ◽  
X Ray Diffraction ◽  
Unit Cell Parameters ◽  
X Ray ◽  
Cell Parameters ◽  
Modified Pechini Method ◽  
Scanning Electron

In the present work, LaNi0.5Ti0.45Co0.05O3, LaNi0.45Co0.05Ti0.5O3, and LaNi0.5Ti0.5O3 perovskites were synthesized by the modified Pechini method. These materials were characterized using X-ray fluorescence, scanning electron microscopy, and powder X-ray diffraction coupled to the Rietveld method. The crystal structure of these materials is orthorhombic, with space group Pbnm (No 62). The unit-cell parameters are a = 5.535(5) Å, b = 5.527(3) Å, c = 7.819(7) Å, V = 239.2(3) Å3, for the LaNi0.5Ti0.45Co0.05O3, a = 5.538(6) Å, b = 5.528(4) Å, c = 7.825(10) Å, V = 239.5(4) Å3, for the LaNi0.45Co0.05Ti0.5O3, and a = 5.540(2) Å, b = 5.5334(15) Å, c = 7.834(3) Å, V = 240.2(1) Å3, for the LaNi0.5Ti0.5O3.

Optical properties of anatase TiO2 films modified by N ion implantation

2012 ◽  
Vol 90 (1) ◽  
pp. 39-43 ◽  
Author(s):  
X. Xiang ◽  
D. Chang ◽  
Y. Jiang ◽  
C.M. Liu ◽  
X.T. Zu
Keyword(s):  
Thin Films ◽  
Ion Implantation ◽  
Photoelectron Spectroscopy ◽  
Radio Frequency Magnetron Sputtering ◽  
X Ray Diffraction ◽  
X Ray ◽  
Atomic Force ◽  
Light Region ◽  
Uv Visible ◽  
Substrate Temperatures

Anatase TiO2 thin films are deposited on K9 glass samples at different substrate temperatures by radio frequency magnetron sputtering. N ion implantation is performed in the as-deposited TiO2 thin films at ion fluences of 5 × 1016, 1 × 1017, and 5 × 1017 ions/cm2. X-ray diffraction, atomic force microscope, X-ray photoelectron spectroscopy (XPS), and UV–visible spectrophotometer are used to characterize the films. With increasing N ion fluences, the absorption edges of anatase TiO2 films shift to longer wavelengths and the absorbance increases in the visible light region. XPS results show that the red shift of TiO2 films is due to the formation of N–Ti–O compounds. As a result, photoactivity is enhanced with increasing N ion fluence.

ITO Thin Films on Silicon Buffer by Sol Gel Method

2006 ◽  
Vol 514-516 ◽  
pp. 1155-1160 ◽  
Author(s):  
Talaat Moussa Hammad
Keyword(s):  
Thin Films ◽  
Indium Tin Oxide ◽  
Optical Transmission ◽  
Sol Gel ◽  
Precursor Solution ◽  
Charge Carriers ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ito Thin Films ◽  
Uv Visible

Sol gel indium tin oxide thin films (In: Sn = 90:10) were prepared by the sol-gel dipcoating process on silicon buffer substrate. The precursor solution was prepared by mixing SnCl2.2H2O and InCl3 dissolved in ethanol and acetic acid. The crystalline structure and grain orientation of ITO films were determined by X-ray diffraction. The surface morphology of the films was characterized by scanning electron microscope (SEM). Optical transmission and reflectance spectra of the films were analyzed by using a UV-visible spectrophotometer. The transport properties of majority charge carriers for these films were studied by Hall measurement. ITO thin film with electrical resistivity of 7.6 ×10-3 3.cm, Hall mobility of approximately 2 cm2(Vs)-1 and free carrier concentration of approximately 4.2 ×1020 cm-3 are obtained for films 100 nm thick films. The I-V curve measurement showed typical I-V characteristic behavior of sol gel ITO thin films.

scholarly journals Decolorization of Methylene Blue by Ag/SrSnO3 Composites under Ultraviolet Radiation

2014 ◽  
Vol 2014 ◽  
pp. 1-10 ◽  
Author(s):  
Patcharanan Junploy ◽  
Titipun Thongtem ◽  
Somchai Thongtem ◽  
Anukorn Phuruangrat
Keyword(s):  
Electron Microscopy ◽  
Methylene Blue ◽  
Uv Radiation ◽  
Photoelectron Spectroscopy ◽  
Separation Process ◽  
X Ray Diffraction ◽  
Electron Hole ◽  
X Ray ◽  
Negative Effect ◽  
Uv Visible

SrSn(OH)6 precursors synthesized by a cyclic microwave radiation (CMR) process were calcined at 900°C for 3 h to form rod-like SrSnO3. Further, the rod-like SrSnO3 and AgNO3 in ethylene glycol (EG) were ultrasonically vibrated to form rod-like Ag/SrSnO3 composites, characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), electron microscopy (EM), Fourier transform infrared (FTIR) spectroscopy, and UV-visible analysis. The photocatalyses of rod-like SrSnO3, 1 wt%, 5 wt%, and 10 wt% Ag/SrSnO3 composites were studied for degradation of methylene blue (MB, C16H18N3SCl) dye under ultraviolet (UV) radiation. In this research, the 5 wt% Ag/SrSnO3 composites showed the highest activity, enhanced by the electron-hole separation process. The photoactivity became lower by the excessive Ag nanoparticles due to the negative effect caused by reduction in the absorption of UV radiation.

Solvothermal synthesis and characterization of well-dispersed cerium-doped Y2SiO5 phosphor particles

2021 ◽  
Vol 112 (10) ◽  
pp. 812-816
Author(s):  
Xianxue Li
Keyword(s):  
Solvothermal Method ◽  
Luminescence Decay ◽  
X Ray Diffraction ◽  
X Ray ◽  
Fluorescence Spectrophotometry ◽  
Decay Properties ◽  
Transmission Electron ◽  
Water As Solvent ◽  
Pure Phase

Abstract Well-dispersed cerium-doped Y2SiO5 (Ce:YSO) phosphor particles with spherical morphology and good luminescence intensity have been achieved by a solvothermal method with ethanol and water as solvent media. X-ray diffraction, Fourier transform infrared spectroscopy, fluorescence spectrophotometry and transmission electron microscopy were employed to characterize the as-synthesized Ce:YSO precursor and powders. The results showed that pure-phase Ce:YSO powders with a mean particle size of about 162 nm were accurately available at 310°C and above. The fluorescence ability and persistent luminescence decay properties of the Ce:YSO powders were also studied, and the excellent fluorescence properties could be attributed to the homogeneous Ce:YSO particles obtained through the solvothermal method.

Synthesis of Nanocomposites of V2OO5©Selenium Nanoparticles and Multiwalled Carbon Nanotubes for Antimicrobial Activity

2021 ◽  
Vol 21 (11) ◽  
pp. 5673-5680
Author(s):  
Muthukrishnan Francklin Philips ◽  
Jothirathinam Thangarathinam ◽  
Jayakumar Princy ◽  
Cyril Arockiaraj Crispin Tina ◽  
Cyril Arockiaraj Crispin Tina ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Antimicrobial Activity ◽  
Multiwalled Carbon Nanotubes ◽  
Xrd Analysis ◽  
X Ray Diffraction ◽  
Multiwalled Carbon ◽  
X Ray ◽  
Functionalized Multiwalled Carbon Nanotubes ◽  
Uv Visible ◽  
Micro Organisms

The authors report the preparation of the nanocomposite comprising of vanadium pentoxide (V2O5) and selenium (Se) nanoparticles and functionalized multiwalled carbon nanotubes (MWCNTs) (V2O5@Se NPs/MWCNTs). Since Se NPs possesses extraordinary physicochemical properties including larger surface area with higher adsorption capacity, V2O5 NPs were adsorbed onto Se NPs surface through physisorption process (designated as V2O5@Se NPs). The nanocomposite synthesized hydrothermally was evaluated for its antimicrobial activity. The morphology and microstructure of the nanocomposite were characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD) analysis, respectively. Fourier transform infrared spectroscopy (FTIR) and UV-Visible spectroscopy (UV-Vis) were employed to analyze the spectral properties of nanocomposite. The microbicidal efficacy of nanocomposite was tested against Gram-negative (G-)ZGram-positive (G+) bacteria and fungus. This is the first report on the synthesis of V2O5@Se NPs/MWCNTs nanocomposites by chemical method that showed microbicidal effect on micro-organisms. The thiol (-SH) units facilitates the enrichment of V2O5@Se NPs onto MWCNTs surface. Ultimately, it reflects on the significant antimicrobial activity of V2O5@Se NPs/MWCNTs.

TiO2 nanofibers fabricated by electrospinning technique and degradation of MO dye under UV light

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Naveen Thakur ◽  
Nikesh Thakur ◽  
Viplove Bhullar ◽  
Saurabh Sharma ◽  
Aman Mahajan ◽  
...  
Keyword(s):  
Raman Spectroscopy ◽  
Fiber Diameter ◽  
Uv Light ◽  
Rutile Phase ◽  
Powder Form ◽  
X Ray Diffraction ◽  
Electrospinning Technique ◽  
Tio2 Nanofibers ◽  
X Ray ◽  
Uv Visible

Abstract Titanium dioxide (TiO2) nanofibers were synthesized by electrospinning to optimize the photocatalytic action efficiency. The synthesis of the fibers was carried out at four different wt% concentrations: 8, 9, 10 & 11% of polymer polyvinylpyrrolidone (PVP). The TiO2 fibers were further calcined at 700 °C to get powder form. The uncalcinated and calcined TiO2 nanofibers were characterized by using X-Ray diffraction (XRD), Raman spectroscopy, Scanning electron microscopy (SEM) and UV-Visible spectroscopy. Raman spectroscopy confirmed the rutile phase of the calcined TiO2nanofibers in powder form with a crystallite size of 34–38 nm. The surface morphology of the uncalcinated and calcined TiO2 nanofibers was examined by SEM and the fiber diameter found to be 360–540 nm. The optical bandgap of the calcined TiO2 nanofibers was found in the range of 3.29–3.24 eV. The photocatalytic activity of the TiO2 nanofibers as examined for uncalcinated and calcined nanofibers, methyl orange (MO) dye degraded up to 98 and 78%, respectively in 180 min under the exposure of UV light. Uncalcinated TiO2 nanofibers were found more suitable for degradation of MO dye as compared to calcined nanofibers.

Sign in / Sign up

Export Citation Format

Share Document