scholarly journals Bioremediation of Hydrocarbon Contaminated Soil: Assessment of Compost Manure and Organic Soap

2019 ◽  
Vol 7 (5) ◽  
pp. 13-22 ◽  
Author(s):  
Hilary Uguru ◽  
Akpokodje, O. I.

This study was carried out to investigate the effect of compost manure and organic soap on hydrocarbon degradation in petroleum products contaminated soil. 10 kg of top soil collected at a depth of 0-20 cm, air dried and sieved, were poured into plastic containers. The soil samples were was pounded with 1 L of spent engine oil, 1 L of kerosene, 1 L of petrol and 1 L of diesel daily for five days. The containers were placed under natural environmental conditions for three weeks to enable full acclimatization of the petroleum products with the soil. A completely randomized design comprising T1 (Polluted soil without treatment ‘control’); T2 (10 kg contaminated soil + 500 g organic soap); T3 (10 kg contaminated soil + 500 g compost manure); and T4 (10 kg contaminated soil + 500 g compost manure + 500 g organic soap) was used for this study. Some physical characteristics (soil porosity and specific gravity) and Total Hydrocarbon Content (THC) of the soil samples were tested for, after the full acclimatization of the soil samples, and at the end of the 10 week experimental period, in accordance with standard methods. Results of the study showed that addition of the compost manure and organic soap the contaminated soil samples significantly (p ≤0.05) degraded the THC, and improved the soil physical characteristics. The result showed that the combination of compost manure and organic soap gave the best remediation result (from 957.21 mg/kg to 154.36 mg/kg), followed by organic soap (from 957.21mg/kg to 203.61 mg/kg), and then compost manure (from 957.21 mg/kg to 262.03 mg/kg). At the end of the experimental period, vegetative growth was observed in the treated soil samples; whereas,  in the control soil samples vegetative growth was absent. Results obtained from this study have shown that amending petroleum products contaminated soils with compost manure and organic soap will enhance remediation of petroleum products contaminated sites.

2020 ◽  
Vol 857 ◽  
pp. 234-242
Author(s):  
Mahmoud S. Abdul Kareem ◽  
Mustafa A. Kadhem ◽  
Halah K.T. AL-Nealy ◽  
Lina H.A. AL-Midhatee

This study focuses on studying the impacts of residues oil on the geotechnical properties of soil and the performance of raft footing rested on oil contaminated soil and subjected to vertical loads. The contaminant used in the present study is residues oil, which is by product disposed of diesel engine oils. The soil samples are contaminated artificially by soaking with two percentage of disposed engine oil of contaminant consist of (disposed engine oil and gasoline) of 20% weight of dried of intact soil samples to obtain different concentrations of contaminant absorbed by soil samples for 30 days to complete the saturation. The mechanical model manufactured to investigate the behavior of raft footing under vertical static loading rested on intact and contaminated soils. The obtained results detected contaminant content have notable impacts on the physical soil characteristics such as the fine particles, specific gravity, plasticity index, and maximum dry unit weight decreased with the increase of contaminant content than that of intact soil. The mechanical soil properties of soil indicated the increase of the compressibility of soil with increase of residues oil percentage, but the soil strength and stiffness are decreased notably. In addition, the total and permanent settlement of raft footing constructed in contaminated soil samples increased by (27-43) % and by (41-58) % than that of an intact soil sample, respectively.


Author(s):  
Olayinka O. Idris ◽  
◽  
Olayinka T. Ogunmefun ◽  
Cinderella N. Tuesimi

One of the biological compounds limiting soil water retention capacity is oil when present due to its hydro-nature. However, some microorganisms exhibit the capacity to degrade oil as a source of carbon, whereby the soil quality is retained and enhanced. Hence, the gravimetric profile of hydrocarbon degrading bacteria and fungi isolated from oil contaminated soil samples was investigated. Soil samples were collected from surface and 10m depth from six different mechanic workshops and generator sites. The pour plate technique was used to isolate the microorganisms. All pure isolates were sub-cultured using Bushnell Haas agar and the isolated bacteria were identified by their morphological and biochemical characteristics. The soil samples pH range was 4.3 - 6.4. Bacteria isolated included Pseudomonas spp., Staphylococcus spp., Microccocus spp., Acinetobacter spp., and Bacillus spp. The fungi isolated included Aspergillus spp., Rhizopus spp., Candida spp., Trichoderma spp. and Penicillium spp. Degradation of kerosene, diesel, crude oil, engine oil, and spent engine oil was allowed using Acinetobacter baumanni, P. aeruginosa, B. subtilis, and S. aureus. Gravimetric analyses were used to determine the percentage of petroleum hydrocarbon degraded by bacterial isolates. The highest percentage of degradation was between P. aeruginosa and B. subtilis. Pseudomonas aeruginosa degraded 97.4% diesel, 88.2% kerosene, 71.3% crude oil, 80.7% engine oil and 78.2% spent engine oil; while Bacillus subtilis degraded 71% diesel, 97% kerosene, 89.6% crude oil, 87% engine oil and 72.6% spent engine oil. This study revealed that bacterial and fungal isolates from oil contaminated soils exhibited the potentials to degrade oil and bioremediation using these microorganisms was possible.


Author(s):  
O. I. Akpokodje ◽  
H. Uguru

This study investigated the impact of petroleum products on the physiochemical properties, heavy metals and THC of soil samples; and their possible phytoremediation. Perforated plastic buckets were filled with 10 kg of sieved virgin topsoil. A mixture of 2 L of spent engine oil, 2 L of kerosene, 2 L of petrol and 2 L of diesel was gradually poured into each bucket and allowed to drain through the soil, once a day for five days, and there after left to stabilize for a period of 21 days. Fluted pumpkin (Telforia Occidentalis) and Okra (Abelmoschus esculentus, Cv. Kirikou) seeds were planted in buckets and closely monitored for 14 weeks. Soil analysis of the virgin topsoil, contaminated soil and remediated soil was done using standard methods. Tests results showed that the petroleum products significantly (p ≤0.05) altered the physicochemical properties, heavy metals and THC of the soil. From the results, the soil porosity decreased from 35% to 14%; specific gravity decreased from 2.34 to 1.35; the soil pH decreased from 7.05 to 5.34; the THC increased from 0,923 mg/kg to 964.35 mg/kg; copper level increased from 4.892 mg/kg to 7.729 mg/kg; the lead content increased from <0.0001 mg/kg to 1.128 mg/kg; while the iron content increased from 1251.2 mg/kg to 1587.9 mg/kg after the contamination. After the 14 weeks phytoremediation period, Telfairia occidentalis was able to degrade the THC in the soil from 964.35 mg/kg to 82.67 mg/kg; while Abelmoschus esculentus degraded the THC in the soil from 964.35 mg/kg to 104 mg/kg. Therefore, due to the harmful effects of the petroleum products on agricultural soils, laws banning their indiscriminate disposal of should be enforced.


2015 ◽  
Vol 17 (3) ◽  
pp. 565-573 ◽  

<div> <p>Petroleum products are used in different forms in auto-mechanic workshops every day. Spent motor oil disposed-off improperly contains potentially toxic substances which can seep into the water tables and contaminate ground water. This study involved isolation and screening of bacterial species capable of utilizing hydrocarbons from three auto-mechanic workshops in Abeokuta, Ogun State. Total Heterotrophic Bacterial Counts ranged from 1.03 &times; 10<sup>6</sup> to 2.81 &times; 10<sup>6 </sup>CFU/g. Total Oil Degrading Bacterial Counts varied between 4.0 &times; 10<sup>5</sup> and 2.01 &times; 10<sup>6</sup> CFU/g while Surface Active Bacterial Counts were from 1.2 &times; 10<sup>4</sup> to 2.76 &times; 10<sup>5</sup> CFU/g. Twenty-four bacteria species capable of utilizing petroleum as a carbon source were isolated from various contaminated soils using enrichment technique. Isolated bacteria include: <em>Bacillus </em>spp., <em>Pseudomonas aeruginosa,</em> <em>Micrococcus </em>spp., <em>Proteus mirabilis</em>, <em>Proteus vulgaris </em>and<em> Enterobacter </em>spp. Redox indicator 2, 6-dichlorophenol indophenol (DCPIP) was used to screen for efficient hydrocarbon (Kerosene, Premium Motor Spirit, and Engine oil) degradation by bacteria. Degradation efficiency was measured by optical density at 600 nm. <em>Micrococcus </em>spp., <em>Proteus mirabilis</em>, and <em>Pseudomonas aeruginosa</em> were found to be the best isolates growing on majority of hydrocarbons due to their high utilization value when growing on the hydrocarbons tested.</p> </div> <p>&nbsp;</p>


2016 ◽  
Vol 59 ◽  
pp. 38-47
Author(s):  
Conrad K. Enenebeaku ◽  
Chidozie N. Anyanwu ◽  
Nnaemeka J. Okorocha ◽  
Uchechi E. Enenebeaku ◽  
Emmanuel Nzediegwu ◽  
...  

In order to estimate plant available fraction of metals in two soil samples-contaminated soil (A) and non-contaminated soil (B), a vegetable crop,Curcubita ficifoliawas grown on both soil samples. The matured leaf was harvested and analyzed for its metal concentration after three (3) months of growth. The soil samples were collected before and after planting, digested with acid and analyzed to determine the pseudo total metal concentration and quantification was done using atomic absorption spectroscopy (AAS). To correlate metal accumulation by the vegetable with potential bioavailability of metals in soils, sequential extraction (SE) using the modified BCR technique was performed on the soils. Soil sample B was used for quality control. It was observed that each metal differed considerably in uptake. And theC. ficifoliacultivated on soil sample A had tissue concentrations of Zn, Mn and Cu as follows: 39.6mgkg-1, 18.3mgkg-1and 26.3mgkg-1respectively. Also,C. ficifoliacultivated on soil sample B had a lower absorption of Zn, Mn and Cu with concentrations of 10.21mgkg-1, 9.11mgkg-1, and 7.6mgkg-1respectively. Results of sequential extraction showed that Zn for soil sample A, and Fe for sample B were mostly present in the acid exchangeable and reducible fractions where these metals were mostly taken up.


2009 ◽  
Vol 62-64 ◽  
pp. 451-455 ◽  
Author(s):  
F.A. Aisien ◽  
J.C. Chiadikobi ◽  
E.T. Aisien

This paper considered the toxicity assessment of some crude oil contaminated soils in Niger Delta areas. The soil samples were collected from different horizontal distances, vertical depths and contaminated soil of different ages. The heavy metals in the contaminated soils were digested and extracted using di-acid digested and DTPA extraction methods respectively. The physiochemical parameters (moisture content, pH, N, P and heavy metals (Ni, Pb and Cd) were analysed with APHA method. The heavy metals concentration was determined using atomic absorption spectrophotometer (AAS). The results show that the metals concentration decreased with the age of the contaminated soil and with increased vertical depths. However, the metals concentrations were almost constant at different horizontal distances. Similar trend was observed for the moisture content, pH, N, P and K.


2018 ◽  
Vol 2018 ◽  
pp. 1-9 ◽  
Author(s):  
Chuang Yu ◽  
Raoping Liao ◽  
Chaopeng Zhu ◽  
Xiaoqing Cai ◽  
Jianjun Ma

Oil-contaminated soils have been paid much attention due to the reclamation of industrial lands in coastal cities of China. As known, oil-contaminated soils are inapplicable for construction due to their weak engineering properties, thus leading to the requirement of remediation and reclamation for oil-contaminated sites. This study presents an experimental investigation on the stabilization of contaminated soils with Portland cement. Investigations including the Atterberg limits, unconfined compressive strength, direct shear strength, and microstructure of cement-stabilized soils have been carried out, verifying the suitability of applying cement to improve engineering properties. Experimental results show that the geotechnical properties of contaminated soil are very poor. With the application of cement, the liquid limit and plasticity index of contaminated soil samples decrease dramatically, and the strength of treated soils has been improved. Experimental results from scanning electron microscope (SEM) indicate that cement-stabilized oil-contaminated soil is featured with a stable supporting microstructure, owing to the cementation between soil particles. This also confirms the applicability of cement to be served as an additive to treat oil-contaminated soils.


2020 ◽  
Vol 8 (1) ◽  
pp. 91-104
Author(s):  
Elizabeth Adeyinka AJIBOYE ◽  
Hikmat Omolara SULAYMAN ◽  
Abdullahi Taiwo AJAO

The research aimed to investigate the bioremediation of spent engine oil on selected contaminated soils within Ilorin metropolis. To achieve this, soil samples were collected from three (3) mechanic workshops along Taiwo axis within the metropolis. The soil samples were then subjected to bioremediation using the land-farming approach. The physicochemical parameters of the soil samples before and after bioremediation were analyzed using standard methods. Bacteria were isolated using standard procedures and identified using biochemical tests and molecular methods. Results for the physicochemical parameters of the soil samples before bioremediation include particle size (all sandy in nature); pH (6.00 ± 0.14 - 6.20 ± 0.14); Organic carbon (14.65 ± 3.20 - 17.54 ± 1.87), Organic matter (33.50 ± 0.85 - 43.45 ± 9.12) and heavy metals (ND - 11.74 ± 0.07). Values after bioremediation for pH, organic carbon, organic matter and heavy metals were 8.25 ± 0.07 - 8.90 ± 0.14, 13.07 ± 0.05 - 13.25 ± 0.84, 37.25 ± 1.06 - 44.80 ± 1.13, ND - 9.40 ± 0.04 respectively. Values for bacterial count before and after bioremediation of the soil samples were 8.00  1.41 - 67.50 ± 2.12 x 105 CFU/mL and 6.50 ± 2.12 - 164.00 ± 11.31 x 105 CFU/mL respectively. Bacterial isolates were identified as Pseudomonas sp., Enterobacter sp., Acinetobacter sp., and Bacillus sp. while the hydrocarbon-utilizing bacteria were identified as Thalassospira mesophila strain JCM 18969; Pseudomonas fluorescens F113; Siccibacter turicensis LMG 23730; Pseudomonas Zeshuii strain KACC 15471; Pseudomonas stutzeri strain CGMCC 1.1803 and Marinobacter hydrocarbonoclasticus strain ATCC 49840. In conclusion, the bacteria isolates effectively bioremediated the spent engine oil contaminated soils with a reduction of hydrocarbon pollutants.


2018 ◽  
Author(s):  
A. A. Ayandele

AbstractThe potential of six microorganisms (Pseudomonas aeruginosa, Micrococcus sp, Flavobacterium sp, Rhizopus sp, Penicillium sp and Fusarium sp) isolated from hydrocarbon contaminated site were evaluated for their biodegradation ability. The soil samples were contaminated with 5% (w/v) of spent engine oil and the rate of biodegradation of the oil was studied for a period of 10weeks under greenhouse experiment. The total heterotrophic bacteria count (THBC), total hydrocarbon degrading bacteria count (THDBC), physicochemical and heavy metals properties of the soil samples and Total Petroleum Hydrocarbon (TPH) were determined after treatment with test organisms. THBC and THDBC ranged from 0.175 to 0.280 CFUg-1 and 0.47 CFUg-1 respectively for the control plot, while THBC is ranging from 0.197 to 0.275 CFUg-1 and THDBC was 0.180 to 0. 473 CFUg-1 for the contaminated plot. There was a slight increase in the pH value of the contaminated soil sample and the treated soil samples as the experimental weeks increased. The results obtained showed a significant decrease (at p ≤ 0.05) in the nutrients content of the soil samples. There was an increase from 1.09 in the control to 15.5% in the content of organic matter after contamination and from 1.88% to 26.8% in the % of organic matter too. There was a significant reduction (at p ≤ 0.05) in the concentration of Fe, Zn, Pb, Cd, Cu, Cr and Ni after 10 weeks of incubation with the tested organisms. Plant growth in the treated contaminated soil samples ranged from 32.6cm to 38.6cm, while that of the control 1 (Uncontaminated soil) was 51.2cm and 19.7cm high was observed in the Control 2 (contaminated untreated soil) after 22 days of the experiment. The TPH degradation (% loss) ranged from 79.7 to 89. 2% after 10 weeks of treatment. P. aeruginosa had the highest level of degradation (89.2%), while Micrococcus sp and Rhizopus sp had the least degradation at 79.9%.All the microorganisms used in this study had the abilities to remediating soil contaminated with spent engine oil and the remediated soil samples were able to support the growth of Zea mays at 5% (w/v) level of contamination.


2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Myoung-Soo Ko ◽  
Seunghak Lee

AbstractThe biodiesel containing fatty acid methyl esters (FAMEs) are blended with refined diesel products. Here, we evaluate relative FAME composition ratio as a potential index to discriminate the pollution origin in diesel-contaminated soil. Artificially contaminated soil was prepared to mimic the release of petroleum products using four different refined diesels; in addition, the contaminated soil was put under natural weathering conditions. The variations in the relative FAME composition ratio was compared with those of the corresponding diesel origin using principal component analysis (PCA) for 60 days. All soil samples could be classified into four groups according to diesel origin using two principal components. The proposed method can be used to discriminate the specific diesel pollution origin in contaminated soils.


Sign in / Sign up

Export Citation Format

Share Document