Effect of a waterproof agent on gypsum particleboard properties

Holzforschung ◽  
2006 ◽  
Vol 60 (3) ◽  
pp. 318-321 ◽  
Author(s):  
Yuhe Deng ◽  
Ling Xuan ◽  
Qian Feng
Keyword(s):  
Crystal Size ◽  
Property Values ◽  
Modulus Of Rupture ◽  
Test Results ◽  
Control Board ◽  
X Ray Diffraction ◽  
Thickness Swelling ◽  
X Ray ◽  
Negative Effect ◽  
Gypsum Particleboard

Abstract This paper describes the influence of the addition of an organosilicon waterproof agent on the properties of gypsum particleboard (GPB). Test results showed that the additive at an appropriate concentration reduces the thickness swelling (TS) and water absorption (WA), and increases the mechanical properties. TS was lowered to ∼1.6% and internal bond strength (IB) was increased to ∼0.4 MPa when 3% organosilicon agent was added. Accordingly, the TS was reduced by 53% and the IB increased by 45% relative to control board without additives. The modulus of rupture (MOR) and modulus of elasticity (MOE) were also increased in the presence of the organosilicon waterproof agent. The effect was pronounced for MOR. On the other hand, too high a content of organosilicon additive had a negative effect and the corresponding property values were poorer. X-Ray diffraction revealed that the content of gypsum dihydrate increased in the presence of the additive, but other chemical changes were not observed. Scanning electron microscopy (SEM) confirmed that the crystal size in gypsum was reduced is the presence of the additive.

scholarly journals Study on the Electrical, Structural, Chemical and Optical Properties of PVD Ta(N) Films Deposited with Different N2 Flow Rates

Coatings ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 937
Author(s):  
Yingying Hu ◽  
Md Rasadujjaman ◽  
Yanrong Wang ◽  
Jing Zhang ◽  
Jiang Yan ◽  
...  
Keyword(s):  
Crystal Structure ◽  
Optical Properties ◽  
Photoelectron Spectroscopy ◽  
Crystal Size ◽  
Silicon Substrates ◽  
X Ray Diffraction ◽  
Dc Magnetron Sputtering ◽  
Flow Rates ◽  
X Ray ◽  
N2 Flow Rate

By reactive DC magnetron sputtering from a pure Ta target onto silicon substrates, Ta(N) films were prepared with different N2 flow rates of 0, 12, 17, 25, 38, and 58 sccm. The effects of N2 flow rate on the electrical properties, crystal structure, elemental composition, and optical properties of Ta(N) were studied. These properties were characterized by the four-probe method, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and spectroscopic ellipsometry (SE). Results show that the deposition rate decreases with an increase of N2 flows. Furthermore, as resistivity increases, the crystal size decreases, the crystal structure transitions from β-Ta to TaN(111), and finally becomes the N-rich phase Ta3N5(130, 040). Studying the optical properties, it is found that there are differences in the refractive index (n) and extinction coefficient (k) of Ta(N) with different thicknesses and different N2 flow rates, depending on the crystal size and crystal phase structure.

Transient liquid phase bonding of Cu and Al using metallic particles interlayers

2021 ◽  
pp. 095440542098823
Author(s):  
Alireza Zaheri ◽  
Mohammadreza Farahani ◽  
Alireza Sadeghi ◽  
Naser Souri
Keyword(s):  
Liquid Phase ◽  
Mechanical Test ◽  
Transient Liquid Phase ◽  
Transient Liquid Phase Bonding ◽  
Joint Interface ◽  
Test Results ◽  
X Ray Diffraction ◽  
X Ray ◽  
Metallic Particles ◽  
Powder Interlayer

The bonding strength, and microstructures of Cu and Al couples using metallic powders as interlayer during transient liquid phase bonding (TLP bonding) were investigated. The interfacial morphologies and microstructures were studied by scanning electron microscopy equipped with energy dispersive X-ray spectroscopy, and X-ray diffraction. First, to explore the optimum bonding time and temperature, nine samples were bonded without interlayers in a vacuum condition. Mechanical test results indicated that bonding at 560°C in 20 min returns the highest bond strength (84% of Al). This bonding condition was used to join ten samples with powder interlayers. Powders were prepared by mixing different combinations of Cu, Al (+Fe nanoparticles) and Zn. In the bonding zone, different Cu9Al4, CuAl, and CuAl2 intermetallic co-precipitate. The strongest bonding is formed in the sample with the 70Al (+Fe)-30Cu powder interlayer. Powder interlayers present thinner and more uniform intermetallic layers at the joint interface.

Medium Density Particleboard with Addition of Impregnated Paper

2014 ◽  
Vol 1025-1026 ◽  
pp. 543-546
Author(s):  
Juliana Cortez Barbosa ◽  
Anderson Luiz da Silva Michelon ◽  
Elen Aparecida Martines Morales ◽  
Cristiane Inácio de Campos ◽  
André Luis Christoforo ◽  
...  
Keyword(s):  
Moisture Content ◽  
Modulus Of Elasticity ◽  
Mechanical Tests ◽  
Modulus Of Rupture ◽  
Medium Density ◽  
Test Results ◽  
Thickness Swelling ◽  
Adhesion Test ◽  
Layer Medium ◽  
Determine Moisture Content

The aim of this research was to produce three-layer Medium Density Particleboard (MDP), with the addition of impregnated paper, in the inner layer, in proportions of 1; 5 and 20%. In this study, MDP was composed with particles of small size in outer layers, and larger particles in internal layer. After panel manufacturing, physical and mechanical tests based on Brazilian Code ABNT NBR 14.810 were carried out to determine moisture content; density; thickness swelling; water absorption; modulus of rupture (MOR) and modulus of elasticity (MOE) in static bending and internal adhesion. Test results were compared to commercial panels, produced with 100% Eucalyptus, considering the requirements specified by Brazilian Code. Properties presented values close to normative specifications, indicating positively the possibility of production of MDP using addition of waste paper impregnated.

scholarly journals Decolorization of Methylene Blue by Ag/SrSnO3 Composites under Ultraviolet Radiation

2014 ◽  
Vol 2014 ◽  
pp. 1-10 ◽  
Author(s):  
Patcharanan Junploy ◽  
Titipun Thongtem ◽  
Somchai Thongtem ◽  
Anukorn Phuruangrat
Keyword(s):  
Electron Microscopy ◽  
Methylene Blue ◽  
Uv Radiation ◽  
Photoelectron Spectroscopy ◽  
Separation Process ◽  
X Ray Diffraction ◽  
Electron Hole ◽  
X Ray ◽  
Negative Effect ◽  
Uv Visible

SrSn(OH)6 precursors synthesized by a cyclic microwave radiation (CMR) process were calcined at 900°C for 3 h to form rod-like SrSnO3. Further, the rod-like SrSnO3 and AgNO3 in ethylene glycol (EG) were ultrasonically vibrated to form rod-like Ag/SrSnO3 composites, characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), electron microscopy (EM), Fourier transform infrared (FTIR) spectroscopy, and UV-visible analysis. The photocatalyses of rod-like SrSnO3, 1 wt%, 5 wt%, and 10 wt% Ag/SrSnO3 composites were studied for degradation of methylene blue (MB, C16H18N3SCl) dye under ultraviolet (UV) radiation. In this research, the 5 wt% Ag/SrSnO3 composites showed the highest activity, enhanced by the electron-hole separation process. The photoactivity became lower by the excessive Ag nanoparticles due to the negative effect caused by reduction in the absorption of UV radiation.

Structural changes in titanium dioxide nanocrystals during plastic deformation

2005 ◽  
Vol 38 (5) ◽  
pp. 749-756 ◽  
Author(s):  
Ulrich Gesenhues
Keyword(s):  
Structural Changes ◽  
Crystal Size ◽  
Lower Layer ◽  
High Energy ◽  
Primary Crystal ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Hall Method ◽  
Means Of Transmission

The polygonization of 200 nm rutile crystals during dry ball-milling at 10gwas monitored in detail by means of transmission electron microscopy (TEM) and X-ray diffraction (XRD). The TEM results showed how to modify the Williamson–Hall method for a successful evaluation of crystal size and microstrain from XRD profiles. Macrostrain development was determined from the minute shift of the most intense reflection. In addition, changes in pycnometrical density were monitored. Accordingly, the primary crystal is disintegrated during milling into a mosaic of 12–35 nm pieces where the grain boundaries induce up to 1.2% microstrain in a lower layer of 6 nm thickness. Macrostrain in the interior of the crystals rises to 0.03%. The pycnometrical density, reflecting the packing density of atoms in the grain boundary, decreases steadily by 1.1%. The results bear relevance to our understanding of plastic flow and the mechanism of phase transitions of metal oxides during high-energy milling.

scholarly journals Structural and thermoelectric properties of the Pr2Zr2O7 compound

2019 ◽  
pp. 4-9
Author(s):  
Adolfo Quiroz-Rodríguez ◽  
Cesia Guarneros-Aguilar ◽  
Ricardo Agustin-Serrano
Keyword(s):  
Electron Microscopy ◽  
Thermal Conductivity ◽  
Thermoelectric Properties ◽  
Crystal Size ◽  
Ambient Pressure ◽  
X Ray Diffraction ◽  
X Ray ◽  
Increasing Temperature ◽  
Thermal Stability Of ◽  
Scanning Electron

In this research, it is presented a detailed study of the structural and thermoelectric properties of the pyrochlore zirconium Pr2Zr2O7 compound prepared by solid-state reaction (SSR) in air at ambient pressure. The synthesized sample was characterized using powder X-ray diffraction. The thermal stability of the thermoelectric compound (TE) Pr2Zr2O7 was tested by thermogravimetric analysis (TGA) and differential thermal analysis (DTA). Scanning electron microscopy shows that the crystal size varies between 0.69 and 2.81μm. Electrical conductivity (\sigma) of the sample calcined at 1400 °C presented values increase irregularly with the increasing temperature from 0.001 to 0.018 S cm-1 as expected in a semiconductor material. The thermal conductivity is lower than 0.44 - 775 W m-1 K-1 which is quite anomalous in comparison with the thermal conductivity of other oxides.

Structure Characterization of Sintered CaO-Al2O3-SiO2 Glass-Ceramic Reinforced with Spodumene

2013 ◽  
Vol 834-836 ◽  
pp. 309-314
Author(s):  
Zi Fan Xiao ◽  
Jin Shu Cheng ◽  
Jun Xie
Keyword(s):  
Glass Ceramic ◽  
Energy Dispersive Spectrometry ◽  
Crystal Size ◽  
Bending Strength ◽  
Glass Ceramics ◽  
Structure Characterization ◽  
X Ray Diffraction ◽  
Crystalline Phases ◽  
X Ray

A glass-ceramic belonging to the CaO-Al2O3-SiO2(CAS) system with different composition of spodumene and doping the Li2O with amount between 0~2.5 % (mass fraction) were prepared by onestage heat treatment, under sintering and crystallization temperature at 1120 °C for two hours. In this paper, differential thermal analysis, X-ray diffraction, scanning electron microscopy, energy dispersive spectrometry and bending strength test were employed to investigate the microstructure and properties of all samples. β-wollastonite crystals were identified as the major crystalline phases, and increasing Li2O was found to be benefit for the crystallization and tiny crystalline phases remelting, resulting in the content of major crystalline phases increased first and then decreased with increasing the expense of spodumene. Meanwhile, the crystal size can be positively related with the content of Li2O. The preferable admixed dosage of spodumene can be obtained, besides the strength of glass-ceramics can be more than 90 MPa.

The determination of crystal size and disorder from X-ray diffraction photographs of polymer fibres. 1. The accuracy of determination of Fourier coefficients of the intensity profile of a reflection

1989 ◽  
Vol 22 (4) ◽  
pp. 363-371 ◽  
Author(s):  
R. Somashekar ◽  
I. H. Hall ◽  
P. D. Carr
Keyword(s):  
Crystal Size ◽  
Fourier Coefficients ◽  
Intensity Profile ◽  
X Ray Diffraction ◽  
Scattering Angle ◽  
X Ray ◽  
Fourier Cosine ◽  
High Harmonics ◽  
Lattice Planes

Methods which determine the number and disorder of lattice planes in a crystal from the Fourier cosine coefficients of the intensity profile of an X-ray reflection use only the low harmonics and require that the coefficients be normalized so that the zero harmonic is unity. Experimentally, the profiles can only be recorded over a smaller range of scattering angle than required by the theory, and it is necessary to subtract background, which is likely to be estimated with considerable error, before determining the coefficients. It is shown that with polymer fibres this causes serious errors in the normalization, and in the values of those low harmonics used in the size and disorder determination, and prevents reliable values being obtained. Methods which avoid normalization and use only high harmonics are needed. It is shown that disorder may be obtained in such a way, but not size, for which low-order normalized coefficients are essential. A method of extrapolation is described and tested which enables the accurate high harmonics to be used to improve the estimates of the low ones. Whilst this will yield more reliable values of crystal size than are obtainable from existing methods, the accuracy depends entirely on the validity of the extrapolation, which cannot be tested in many cases of interest.

Effect of nano Al2O3 coated Ag reinforced Cu matrix nanocomposites on mechanical and tribological behavior synthesis by P/M technique

2020 ◽  
Vol 54 (30) ◽  
pp. 4921-4928
Author(s):  
A Mohamed ◽  
MM Mohammed ◽  
AF Ibrahim ◽  
Omyma A El-Kady
Keyword(s):  
Wear Behavior ◽  
Composite Coatings ◽  
Microstructural Analysis ◽  
Wear Test ◽  
Test Results ◽  
X Ray Diffraction ◽  
X Ray ◽  
Average Hardness ◽  
Ag Particles ◽  
Matrix Nanocomposites

In this study, copper powder was reinforced with different weight percentages of Al2O3 particles (0, 5, 10, and 15 wt.% Al2O3 coated Ag) to produce Cu-Al2O3 composites by mechanical alloying and uniaxial cold pressing/sintering route. Electro-less deposition was used to coat Al2O3 particles with Ag. The microstructure of the consolidated samples was investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX) elemental mapping. The porosity, microhardness, and wear behavior of the consolidated samples were also investigated as a function of Al2O3 content. The EDX mapping images reveal that the Al2O3 reinforcement particles were homogeneously distributed into the Cu matrix. Microstructural analysis shows that the addition of Al2O3 coated Ag particles improves density of the composites coating. SEM micrographs result shows that slight porosities exist in the composites produced. Furthermore, the average hardness of the composite coatings varies from 72.3 to 187.6 HV as Al2O3 content increases from 0 to 15 wt.%. The wear test results showed that the composite with higher Al2O3 content 15 wt.% showed the best wear resistance.

Sign in / Sign up

Export Citation Format

Share Document