The effect of Al2O3 on fayalite-based copper smelting slags in equilibrium with matte and tridymite at 1 2008C and P(SO2) = 0.25 atm

Author(s):  
Taufiq Hidayat ◽  
Evgueni Jak ◽  
Ata Fallah-Mehrjardi ◽  
Peter C. Hayesa

Abstract Experimental investigations have been undertaken to determine the effect of Al2O3in slag on the gas/slag/matte/tridymite equilibria in the multi-component Cu-Fe-O-S-Si-Al system at 1 200 8C, and P(SO2) = 0.25 atm. The experimental technique involves high temperature equilibration of synthetic samples on the open silica substrate in controlled gas atmospheres (CO/CO2/SO2/Ar), rapid quenching after a designated equilibration time followed by the compositional analysis of the condensed phases with electron probe X-ray microanalyzer. The experimental data of the present study provide information on the effect of alumina on the slag composition, such as the chemically dissolved copper, dissolved sulphur, and Fe/SiO2 ratio in slag at tridymite saturation at different Cu in matte. The new data have been used as inputs for the optimization of the thermodynamic databases for the copper-containing systems and can also be used to evaluate the fluxing strategy in the copper smelting operation.

2005 ◽  
Vol 37 (2) ◽  
pp. 139-145 ◽  
Author(s):  
Aleksandar Grujic ◽  
Nadezda Talijan ◽  
Aleksa Maricic ◽  
Jasna Stajic-Trosic ◽  
Vladan Cosovic ◽  
...  

As a part of these experimental investigations of melt-spun Nd-Fe-B alloy with Nd rich content in relation to Nd2Fe14B prepared by rapid quenching process for optimally selected cooling rate and heat treatment, the influence of the chosen chemical composition on magnetic properties was observed. The results of X-ray diffraction, M?ssbauer spectroscopy phase analysis and magnetic measurement of investigated melt-spun Nd14.5Fe78.5B7 alloy are presented to bring some new information concerning the relation between their structure and magnetic properties.


Author(s):  
John B. Vander Sande ◽  
Thomas F. Kelly ◽  
Douglas Imeson

In the scanning transmission electron microscope (STEM) a fine probe of electrons is scanned across the thin specimen, or the probe is stationarily placed on a volume of interest, and various products of the electron-specimen interaction are then collected and used for image formation or microanalysis. The microanalysis modes usually employed in STEM include, but are not restricted to, energy dispersive X-ray analysis, electron energy loss spectroscopy, and microdiffraction.


Author(s):  
Ivan Saenko ◽  
O. Fabrichnaya

AbstractThermodynamic parameters were assessed for the MgO–FeOx system and combined with already available descriptions of ZrO2-FeOx and ZrO2-MgO systems to calculate preliminary phase diagrams for planning experimental investigations. Samples of selected compositions were heat treated at 1523, 1673 and 1873 K and characterized using x-ray and scanning electron microscopy combined with energy dispersive x-ray spectroscopy (SEM/EDX). Experiments indicated extension of cubic ZrO2 solid solution into the ternary system at 1873 K (75 mol.% ZrO2, 10 mol.% FeOx and 15 mol.% MgO) and limited solubility of 4 mol.% ZrO2 in spinel phase. Based on the obtained results thermodynamic parameters of C-ZrO2 and spinel phase were optimized.


2014 ◽  
Vol 976 ◽  
pp. 52-58 ◽  
Author(s):  
Janeth Sarmiento Arellano ◽  
Enrique Rosendo ◽  
Román Romano ◽  
Gabriela Nieto ◽  
Tomás Díaz ◽  
...  

A comparative study of the synthesis of cadmium selenide (CdSe) nanoparticles (NPs) using different cadmium precursors such as, cadmium nitrate (Cd (NO3)2·4H2O), cadmium acetate ((CH3COO)2Cd·2H2O) and cadmium chloride (CdCl2·2.5H2O) is presented in this work. The method used to obtain the CdSe NPs was the colloidal synthesis at low temperature and atmospheric pressure. The Cd2+ ions were obtained in aqueous solution at room temperature, the surfactant used in the process was an aqueous solution of sodium hydroxide (NaOH), penta-sodium tripolyphosphate and H2O named commonly extran, which not only helps to stabilize the NPs, but also allows adjusting the pH of the solution. Se2- ions were obtained with sodium borohydride (NaBH4) as reductant at 75 oC. The by-products from the reaction were eliminated through a cleaning process with hydrochloric acid (HCl). Molar concentration of Cd:Se was varied from 3:1 to 1:3 and the pH value was varied between 8 and 11. The obtained samples were characterized by X-ray diffraction (XRD), it was seen that the obtained NPs present cubic centered face structure. The crystallite size from the powder was calculated using the Debye-Scherrer equation and was found between 3.3 nm and 5.6 nm, the variation in size depends on the molar concentration of cadmium and selenium. Morphological study was done using scanning electron microscopy (SEM) and compositional analysis was done by energy dispersive x-ray analysis (EDAX).


MRS Advances ◽  
2017 ◽  
Vol 2 (25) ◽  
pp. 1341-1346
Author(s):  
Monica Sorescu ◽  
Felicia Tolea ◽  
Mihaela Valeanu ◽  
Mihaela Sofronie

ABSTRACTSamples of Ni57-xNdxFe18Ga25 with x=2 and 4 were prepared in ribbon form by rapid quenching via melt spinning route. The samples were analyzed by X-ray diffraction (XRD), magnetic measurements and Mössbauer spectroscopy, both in the as-quenched form and after thermal annealing at 900 oC for 2 min and 400 °C for 2 hours. For x=2 the Nd atoms are completely dissolved in the Ni-Fe-Ga matrix, while for x=4 the additional occurrence of the secondary 2:17 phase could be resolved. These findings were supported by the analysis of hyperfine magnetic field distributions obtained from the non-linear least-squares fitting of the Mössbauer spectra.


2018 ◽  
Vol 08 (05) ◽  
pp. 1850031 ◽  
Author(s):  
Ambika Ray ◽  
Banarji Behera ◽  
Tanmoy Basu ◽  
Saumitra Vajandar ◽  
Santosh Kumar Satpathy ◽  
...  

[Formula: see text](BiFe[Formula: see text]GdxO3)–y(PbZrO3) composites [Formula: see text], having four different Gd concentrations ([Formula: see text], 0.1, 0.15, and 0.2), were synthesized and their structural, dielectric, and ferroelectric properties have been studied using different characterization techniques. In addition, to investigate the effect of ion implantation on the microstructure and dielectric properties, these composites were exposed to 2[Formula: see text]MeV He[Formula: see text]-ions. Modifications of the structure, surface morphology and electrical properties of the samples before and after ion exposure were demonstrated using powder X-ray diffraction (XRD), scanning electron microscopy (SEM) technique, and LCR meter. The compositional analysis was carried out using energy dispersive X-ray spectrometry (EDS). XRD results demonstrated a decrease in the intensity profile of the dominant peak by a factor of 6 showing a degradation of the crystallinity. Willliamson–Hall (WH) plots reveal reduction in the grain size after irradiation along with an increase in strain and dislocation density. A decrease in the dielectric constant and loss has been recorded after ion beam exposure with reduction in ac conductivity value. The contribution of grain and grain boundary effect in conduction mechanism has been addressed using Nyquist plots. All the samples demonstrate a lossy ferroelectric loop which shows a clear modification upon irradiation. The role of structural defects modifying the physical properties of the composite materials is discussed in this work.


Materials ◽  
2018 ◽  
Vol 11 (11) ◽  
pp. 2150 ◽  
Author(s):  
Su-Seong Ahn ◽  
Sharief Pathan ◽  
Jar-Myung Koo ◽  
Chang-Hyun Baeg ◽  
Chan-Uk Jeong ◽  
...  

In this research, various processing conditions were implemented to enhance the mechanical properties of Al-Si alloys. The silicon content was varied from hypoeutectic (Si-10 wt.%) to eutectic (Si-12.6 wt.%) and hypereutectic (Si-14 wt.%) for the preparation of Al-XSi-3Cu-0.5Fe-0.6 Mg (X = 10–14%) alloys using die casting. Subsequently, these alloys were hot-extruded with an optimum extrusion ratio (17:1) at 400 °C to match the output extruded bar to the compressor size. An analysis of the microstructural features along with a chemical compositional analysis were carried out using scanning electron microscope along with energy dispersive X-ray spectroscopy and transmission electron microscope. The SEM micrographs of the extruded samples displayed cracks in primary Si, and the intermetallic (β-Al5FeSi) phase was fragmented accordingly. In addition, the silicon phase was homogenously distributed, and the size remained constant. The mechanical properties of the extruded samples were enhanced by the increase of silicon content, and consequently the ductility decreased. By implementing proper T6 heat treatment parameters, coherent Al2Cu phases were formed in the Al matrix, and the Si phase was gradually increased along with the silicon content. Therefore, high tensile strength was achieved, reaching values for the Al-XSi-3Cu-0.5Fe-0.6Mg (X = 10–14%) alloys of 366 MPa, 388 MPa, and 420 MPa, respectively.


2019 ◽  
Vol 81 (1) ◽  
pp. 118-128
Author(s):  
V. V. Balandin ◽  
V. V. Balandin ◽  
V. V. Parkhachev

Investigating impact interaction of solid and deformed bodies with obstacles of various physical natures requires developing experimental methodologies of registering the parameters of the interaction process. In experimental investigations of impact interaction of solids, it is common practice to measure displacement of strikers as a function of time, as well as their velocity and deceleration. To determine the displacement and velocity of a striker, a radio-interferometric methodology of registering the displacement of its rear end is proposed. In contrast with the registration methods based on high-speed filming and pulsed X-ray photography, the method using a millimeter-range radio-interferometer provides continuous high-accuracy registering of the displacement of the rear end of a striker in a wide range of displacement values. To test the effectiveness of the methodology, a series of experiments have been conducted on registering the motion of a cylindrical striker of an aluminum alloy, fired from a 20mm-dia gas gun. The displacement of the striker was also monitored using high-speed filming. The results of measuring using the two methodologies differ within the limits of the error of measurement. Based on the results of the above experiments, it has been concluded that the methodology of determining the displacement and velocity of strikers in a ballistic experiment using a mm-range radio-interferometer makes it possible to measure practically continuously large displacements (100 mm and larger) to a safe accuracy. The present methodology can be used for measuring the displacement and velocity of the rear end of a striker interacting with obstacles of various physical natures (metals, ceramics, soils, concretes, etc.).


2010 ◽  
Vol 97 (15) ◽  
pp. 151906 ◽  
Author(s):  
Sarab Preet Singh ◽  
Mohammed H. Modi ◽  
P. Srivastava

1994 ◽  
Vol 72 (7) ◽  
pp. 1709-1721 ◽  
Author(s):  
Erwin Buncel ◽  
Richard M. Tarkka ◽  
Julian M. Dust

Heats of formation (ΔHf) for a series of aromatics that are progressively more electron deficient (benzene, 6; nitrobenzene, 7; 4-fluoronitrobenzene, 8; 1,3-dinitrobenzene, 9; 2,4,6-trinitroanisole, 2; and 1,3,5-trinitrobenzene, 1) were determined by semiempirical AM1 calculations. As a probe of the factors that govern the regioselectivity exhibited in the formation of anionic σ-adducts (Meisenheimer complexes), experimental gas-phase ΔHf values for the prototypical oxygen and carbon nucleophiles (hydroxide, methoxide, and methide anions) were used in a thermochemical calculation along with the calculated ΔHf of the electrophiles and the adducts to determine the heats of complexation (ΔHc). The present results show that for the series of nitroaryl electrophiles, 7, 9, and 1, hydroxide and methide anions exhibit the same regioselectivity based on thermodynamics of Meisenheimer complex formation. Specifically, Meisenheimer complexes derived from attack at a position para to at least one nitro group (designated MC-4) are formed with the greatest exothermicity (ΔHc). Exothermicity of complexation increases for both hydroxide and methide adduct formation as the number of nitro groups in the electrophile is increased, from 7 to 9 and to 1, but formation of the methide adducts occurs uniformly with greater exothermicity than that of hydroxide adducts. These results are considered in light of solution calorimetric data that quantify adduct stability in condensed phases. Surprisingly, it is found that regioselectivity inverts for CH3−as compared to OH−and CH3O−in complexation with 2,4,6-trinitroanisole, 2. Thus, while methoxide and hydroxide form adducts at C-1 of TNA with higher exothermicity than at C-3, methide preferentially forms an adduct at C-3 according to the same enthalpy criterion. These results arise from the degree of stereoelectronic stabilization that may be imparted to the respective Meisenheimer complexes formed from ipso attack, that is, the adducts (MC-1) that are geminally disubstituted with electronegative heteroatom groups. For the methoxide MC-1 of TNA, 2, full stereoelectronic stabilization is provided by n–σ* donation from nonbonding electron pairs of the acetal-like methoxyl moieties to suitable C—O acceptor bonds. However, the methide moiety of the comparable MC-1 of TNA cannot partake in such an interaction and, so, with methide, MC-3 formation is preferred over MC-1. Further evidence is provided by consideration of the two energy minima obtained from optimization of the geometry of the oxygen-centred adducts formed by attack of methoxide at C-1 of TNA, 2. In the presence of a point charge that simulates an ion-paired cation, an "M-shaped" conformer is favoured for MC-1, while in the absence of a counterion the "S-shaped" conformer is favoured. Without a complexing counterion M and S conformers are both local minima, while the "S" conformer constitutes the global minimum. The AM1 optimized structure for the "M" conformer compares favourably to published X-ray data. The greater exothermicity of formation of the "S" conformer in the absence of the counterion is indicative of stereoelectronic stabilization of the O-adduct. The geometry is rationalized as a result of minimizing steric repulsion and maximizing the n-σ* stabilization of the C-1 adduct.


Sign in / Sign up

Export Citation Format

Share Document