An investigation of the impact of an amino-ended hyperbranched polymer as a new type of modifier on the compatibility of PLA/PBAT blends

2018 ◽  
Vol 38 (3) ◽  
pp. 223-229 ◽  
Author(s):  
Yujuan Jin ◽  
Shuang Men ◽  
Yunxuan Weng
Keyword(s):  
Fourier Transform ◽  
Hyperbranched Polymer ◽  
Poly Lactic Acid ◽  
Melt Mixing ◽  
Sem Images ◽  
Roller Mill ◽  
Elongation At Break ◽  
New Type ◽  
The Impact ◽  
Scanning Electron

AbstractPoly(lactic acid) (PLA)/poly(butylene adipate-co-terephthalate) (PBAT) blends using amino-ended hyperbranched polymers (HBP) as modifiers were prepared by melt-mixing through a double-roller mill and injection molding. It was found that when the content of HBP was 2.5 phr, the elongation at break and the impact strength of PLA/PBAT blends both reached peak values. Moreover, by addition of HBP, the ΔTg of the blends was smaller. These results, together with Scanning electron microscope (SEM) images on the fractured morphology of the blends, indicate that the compatibility between PLA and PBAT is improved upon addition of HBP. The mechanism of the impact of HBP on the improvement of the compatibility between PLA and PBAT is proposed based upon Fourier transform infrared (FTIR) spectra.

Effect of inorganic nanofillers on the impact behavior and fracture probability of industrial high-density polyethylene nanocomposite

2017 ◽  
Vol 52 (18) ◽  
pp. 2431-2442 ◽  
Author(s):  
Harun Sepet ◽  
Necmettin Tarakcioglu ◽  
RDK Misra
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
High Density Polyethylene ◽  
Fracture Probability ◽  
High Density ◽  
Impact Behavior ◽  
Inorganic Filler ◽  
Melt Mixing ◽  
The Impact ◽  
Scanning Electron

The main purpose of this work is to study how the morphology of nanofillers and dispersion and distribution level of inorganic nanofiller influence the impact behavior and fracture probability of inorganic filler filled industrial high-density polyethylene nanocomposites. For this study, nanoclay and nano-CaCO3 fillers–high-density polyethylene mixings (0, 1, 3, 5 wt.% high-density polyethylene) was prepared by melt-mixing method using a compounder system. The impact behavior was examined by charpy impact test, scanning electron microscopy, and probability theory and statistics. The level of the dispersion was characterized with scanning electron microscopy energy dispersive X-ray spectroscopy analysis. The results showed rather good dispersion of both of inorganic nanofiller, with a mixture of exfoliated and confined morphology. The results indicated that the impact strength of the industrial nanocomposite decreased with the increase of inorganic particulate content. The impact reliability of the industrial nanocomposites depends on the type of nanofillers and their dispersion and distribution in the matrix.

scholarly journals The combined plasticization of jute and tung oil anhydride for jute fiber reinforced poly(lactic acid) composites

2021 ◽  
pp. 096739112110576
Author(s):  
Ying Zhou ◽  
Can Chen ◽  
Lan Xie ◽  
Xiaolang Chen ◽  
Guangqiang Xiao ◽  
...  
Keyword(s):  
Lactic Acid ◽  
Physical And Mechanical Properties ◽  
Complex Viscosity ◽  
Poly Lactic Acid ◽  
Melt Blending ◽  
Sem Images ◽  
Pseudoplastic Fluid ◽  
Tung Oil ◽  
Biodegradable Poly ◽  
The Impact

In this work, novel plasticizing biodegradable poly (lactic acid) (PLA) composites were prepared by melt blending of jute and tung oil anhydride (TOA), and the physical and mechanical properties of PLA/jute/TOA composites were tested and characterized. The impact strength of PLA/jute/TOA composites significantly increases with increasing the content of TOA. The SEM images of fracture surface of PLA/jute/TOA composites become rough after the incorporation of TOA. In addition, TOA changes the crystallization temperature and decomposition process of PLA/jute/TOA composites. With increasing the amount of TOA, the value of storage modulus (E′) of PLA/jute/TOA composites gradually increases. The complex viscosity (η*) values for all samples reduce obviously with increasing the frequency, which means that the pure PLA and PLA/jute/TOA composites is typical pseudoplastic fluid. This is attributed to the formation of crosslinking, which restricts the deformation of the composites.

scholarly journals Investigation on compatibility of PLA/PBAT blends modified by epoxy-terminated branched polymers through chemical micro-crosslinking

e-Polymers ◽  
2020 ◽  
Vol 20 (1) ◽  
pp. 39-54 ◽  
Author(s):  
Bo Wang ◽  
Yujuan Jin ◽  
Kai’er Kang ◽  
Nan Yang ◽  
Yunxuan Weng ◽  
...  
Keyword(s):  
Lactic Acid ◽  
Glass Transition ◽  
Sem Analysis ◽  
Branched Polymers ◽  
Poly Lactic Acid ◽  
Elongation At Break ◽  
Butylene Terephthalate ◽  
The Difference ◽  
Physical And Chemical ◽  
The Impact

AbstractIn this study, a type of epoxy-terminated branched polymer (ETBP) was used as an interface compati- bilizer to modify the poly lactic acid (PLA)/poly(butylene adipate-co-butylene terephthalate) (PBAT) (70/30) blends. Upon addition of ETBP, the difference in glass transition temperature between PLA and PBAT became smaller. By adding 3.0 phr of ETBP, the elongation at break of the PLA/PBAT blends was found increased from 45.8% to 272.0%; the impact strength increased from 26.2 kJ·m−2 to 45.3 kJ·m−2. In SEM analysis, it was observed that the size of the dispersed PBAT particle decreased with the increasing of ETBP content. These results indicated that the compatibility between PLA and PBAT can be effectively enhanced by using ETBP as the modifier. The modification mechanism was discussed in detail. It proposes that both physical and chemical micro-crosslinking were formed, the latter of which was confirmed by gel content analysis.

scholarly journals Thermal, mechanical and morphological properties of polyurethane–zirconia loading

2020 ◽  
Author(s):  
Ali J Salman ◽  
Ali Assim Al-Obaidi ◽  
Dalya H Al-Mamoori ◽  
Lina M Shaker ◽  
Ahmed A Al-Amiery
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Thermal Properties ◽  
Material Science ◽  
Morphological Properties ◽  
Flexural Stress ◽  
Renewable Materials ◽  
Sem Images ◽  
The Impact ◽  
Scanning Electron

Abstract The polyurethane (PU) has been showing a dramatic increase in applications related to material science and technology. However, the mechanical, physical and thermal properties could be further improved by loading PU with zirconia (Zr) to create renewable materials known as polyurethane–zirconia (PUZ) composites. In this study, PU matrix was treated with wt.% Zr at 0.5, 1.0, 1.5 and 2.0. In this study, the thermo-mechanical properties and the morphology were investigated of PU and PUZ nano-samples. The images of the scanning electron microscope (SEM) were the prime tool in investigating PU and PUZ surfaces and fractured surfaces showing vanishing the cracks and formation of agglomeration on the sample PUZ-1.5%. In addition, the tensile strength, Young’s modulus and maximum loading were improved by 36.7, 31.8 and 39.1%, respectively, at Zr loading of 1.5 wt.%. The flexural stress and the load were improved by 94.3% and 93.6%, respectively, when Zr loading was 1.5 wt.%. The impact without and with a notch was improved by 110.7% and 62.6%, respectively, at Zr loading of 1.5 wt.%. The the morphologies of the PU surface and Zr surface supported by SEM images. Regarding the storage modulus ability of PU and PUZ composites, Zr loading has negatively influenced E. The E functioning temperature was observed to move from 142 to 183°C. Another effect was determined by adding a small amount of Zr. This small amount was enough to shift the crystallization temperature (${T}_c$) and the melting temperature (${T}_m$) of PU from 125 to 129°C and from 150 to 144°C, respectively.

Effect of Compatibilizer on Impact Strength and Morphology of Polystyrene/Zinc Oxide Nanocomposites

2012 ◽  
Vol 545 ◽  
pp. 330-334
Author(s):  
Sirirat Wacharawichanant ◽  
Pranee Saetun ◽  
Thunwawon Lekkong ◽  
Thongyai Supakanok
Keyword(s):  
Particle Size ◽  
Zinc Oxide ◽  
Impact Strength ◽  
Impact Test ◽  
Screw Extruder ◽  
Melt Mixing ◽  
Zno Particles ◽  
Twin Screw ◽  
The Impact ◽  
Scanning Electron

This article investigated the effects of particle size of zinc oxide (ZnO) and polystyrene-co-maleic anhydride (SMA) compatibilizer on impact strength and morphology of polystyrene (PS)/ZnO71 (71 nm) and PS/ZnO250 (250 nm) nanocomposites. PS/ZnO nanocomposites with varying concentration of ZnO and SMA were prepared by a melt mixing technique in a twin screw extruder. It was found that the impact strength of PS nanocomposites increased up to a ZnO content of 1.0 wt%. Moreover, PS/ZnO250 nanocomposites had higher impact strength than PS/ZnO71 nanocomposites. The addition of SMA increased the impact strength of PS/ZnO nanocomposites with increasing SMA content. The result showed that SMA could improve impact strength of nanocomposites. The dispersion of ZnO particles on PS/ZnO nanocomposites was studied by scanning electron microscope (SEM). It was observed that the dispersion of ZnO particles of PS/ZnO nanocomposites without SMA was non-uniform and the agglomeration of ZnO particles in the polymer matrix increased with increasing ZnO content. The dispersion of ZnO particles of PS/ZnO nanocomposites after adding SMA was relatively good and only few aggregations exist. These observations support the results of the impact test where the PS/ZnO nanocomposites with SMA displayed higher impact strength than the PS/ZnO nanocomposites without SMA. The study showed that SMA was used as a compatibilizer to improve the dispersability and compatibility of ZnO particles in PS matrix.

Study on the Performance of Nano-CaCO3 and LLDPE Based Artificial Turf Fibers

2011 ◽  
Vol 332-334 ◽  
pp. 1077-1081
Author(s):  
Hong Ling Yi ◽  
Wei Shan Wang ◽  
Heng Lin ◽  
Wei Guang Gong ◽  
Ting Wei ◽  
...  
Keyword(s):  
Cross Sections ◽  
Tensile Force ◽  
Accelerated Aging ◽  
Artificial Turf ◽  
Sem Images ◽  
Crystallinity Degree ◽  
Elongation At Break ◽  
Caco3 Content ◽  
New Type ◽  
Strength Retention

In this paper, a new type of LLDPE/nano CaCO3 composite based artificial turf yarns with good tensile property and UV resistance is introduced. The effect of nano CaCO3content on tensile properties shows that the tensile force reached the maximum value when the CaCO3 content is about 7wt%, and the elongation at break gets to the highest point at 10wt%. After 3000h UV accelerated aging, the nano-CaCO3 and LLDPE based artificial turf fiber yarns has tensile strength retention about 87%, and the elongation at break is higher than LLDPE. DSC results shows that with the increase of nano-CaCO3 content, the crystallization temperature gradually increased, and the crystallinity degree declined. SEM images of cross sections of monofilament fibers show that nano CaCO3 had a good dispersion in monofilament fiber matrix. These reasons give rise to the improved mechanical properties of turf yarns.

scholarly journals A study on the mechanical, thermal properties and crystallization behavior of poly(lactic acid)/thermoplastic poly(propylene carbonate) polyurethane blends

RSC Advances ◽  
2017 ◽  
Vol 7 (73) ◽  
pp. 46183-46194 ◽  
Author(s):  
Jia Yang ◽  
Hongwei Pan ◽  
Xin Li ◽  
Shulin Sun ◽  
Huiliang Zhang ◽  
...  
Keyword(s):  
Lactic Acid ◽  
Thermal Properties ◽  
Impact Strength ◽  
Propylene Carbonate ◽  
Crystallization Behavior ◽  
Raw Materials ◽  
Poly Lactic Acid ◽  
Elongation At Break ◽  
Poly Propylene ◽  
The Impact

PPCU was prepared by using PPC and polyols as the raw materials and diphenyl-methane-diisocyanate (MDI) as the extender chain. The impact strength and elongation at break of PLA were remarkably enhanced by blending with PPCU.

scholarly journals Impact of the Graphite Fillers on the Thermal Processing of Graphite/Poly(lactic acid) Composites

Materials ◽  
2021 ◽  
Vol 14 (18) ◽  
pp. 5346
Author(s):  
Daniel Kaczor ◽  
Kacper Fiedurek ◽  
Krzysztof Bajer ◽  
Aneta Raszkowska-Kaczor ◽  
Grzegorz Domek ◽  
...  
Keyword(s):  
Lactic Acid ◽  
Polymer Matrix ◽  
Thermal Processing ◽  
Poly Lactic Acid ◽  
Expandable Graphite ◽  
Slight Reduction ◽  
Melt Mixing ◽  
Neat Polymer ◽  
Industrial Grade ◽  
The Impact

To assess the impact of graphite fillers on the thermal processing of graphite/poly(lactic acid) (PLA) composites, a series of the composite samples with different graphite of industrial grade as fillers was prepared by melt mixing. The average size of the graphite grains ranged between 100 µm and 6 µm. For comparative purposes, one of the carbon fillers was expandable graphite. Composites were examined by SEM, FTIR, and Raman spectroscopy. As revealed by thermogravimetric (TG) analyses, graphite filler slightly lowered the temperature of thermal decomposition of the PLA matrix. Differential scanning calorimetry (DSC) tests showed that the room temperature crystallinity of the polymer matrix is strongly affected by the graphite filler. The crystallinity of the composites determined from the second heating cycle reached values close to 50%, while these values are close to zero for the neat polymer. The addition of graphite to PLA caused a slight reduction in the oxidation induction time (OIT). The melt flow rate (MFR) of the graphite/PLA composites was lower than the original PLA due to an increase in flow resistance associated with the high crystallinity of the polymer matrix. Expandable graphite did not cause changes in the structure of the polymer matrix during thermal treatment. The crystallinity of the composite with this filler did not increase after first heating and was close to the neat PLA MFR value, which was extremely high due to the low crystallinity of the PLA matrix and delamination of the filler at elevated temperature.

Biocomposites of Poly(Lactic Acid) and Cellulose Nanofibers from Cassava Pulp

2017 ◽  
Vol 753 ◽  
pp. 13-17
Author(s):  
Chi Nguyen Thanh ◽  
Ruksakulpiwat Chaiwat ◽  
Ruksakulpiwat Yupaporn
Keyword(s):  
Electron Microscopy ◽  
Lactic Acid ◽  
Impact Strength ◽  
Epoxy Group ◽  
Cellulose Nanofibers ◽  
Poly Lactic Acid ◽  
Melt Mixing ◽  
Hydrolysis Method ◽  
Cassava Pulp ◽  
The Impact

Cellulose nanofibers (CNFs) were used as biobased fillers to prepare poly(lactic acid) (PLA)-based biocomposites. Cellulose nanofibers were extracted from cassava pulp (CP) by acid hydrolysis method. Before submitted to acid treatment, CP was pre-treated by alkali and bleaching treatments. The biocomposites were prepared by melt mixing, followed by hot melt pressing. In order to improve the compatibility of CNFs with PLA matrix, glycidyl methacrylate (GMA) grafted poly (lactic acid) (PLA-g-GMA) was used as a compatibilizer. PLA-g-GMA was prepared by grafting of GMA onto PLA chain via melt mixing using an internal mixer. Transmission electron microscopy (TEM) micrograph shows that most nanofibers with the diameter in the range of 10-30 nm and immeasurable length were obtained. The appearance of two new peaks at 49.07 and 44.71 ppm in the carbon-13 nuclear magnetic resonance (13C-NMR) spectrum of PLA-g-GMA, which represent the carbons of the epoxy group of GMA, confirms that GMA was successfully grafted onto PLA chain. The morphology of biocomposites, characterized by scanning electron microscopy (SEM), reveals that without using PLA-g-GMA, the poor dispersion of CNFs in PLA matrix was observed. In contrast to that, with using PLA-g-GMA, the dispersion of CNFs in PLA matrix was improved. Moreover, the impact strength results show that by incorporating 1.0 wt% CNFs into PLA matrix and using PLA-g-GMA as a compatibilizer, the impact strength of biocomposites was slightly enhanced compared to that of pure PLA.

Improvement of Electrical Conductivity of Polyurethane/Polypyrrole Blends by Graphene

2020 ◽  
Vol 831 ◽  
pp. 122-126
Author(s):  
Pafun Janpoung ◽  
Prasit Pattananuwat ◽  
Pranut Potiyaraj
Keyword(s):  
Thermal Stability ◽  
Electrical Conductivity ◽  
Fourier Transform ◽  
Graphene Oxide ◽  
Controlled Synthesis ◽  
Sem Images ◽  
Thermogravimetric Analyzer ◽  
Solution Blending ◽  
Blending Process ◽  
Scanning Electron

Polyurethane (TPU)/polypyrrole (PPy) blends were successfully prepared by the solution blending process with different contents of reduce graphene oxide (rGO). The controlled synthesis of PPy/rGO composites was reported by varying graphene contents of 10, 20, 30 and 40% w/v. Fourier transform infrared (FTIR) and Scanning electron microscope (SEM) were used to characterize their structures and morphologies. The SEM images show the growing of PPy along the surface of graphene. FTIR illustrated that the PPy/rGO composites were in the doped state. The electrical conductivity of PPy/rGO composites with the concentration of graphene at 40% was about 30 times higher than that of pure PPy. Thermogravimetric analyzer (TGA) thermograms indicated that the PPy/rGO composites have better thermal stability than pure PPy.

Sign in / Sign up

Export Citation Format

Share Document